Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

ARMADILLO

OHWR0007 · revision R1

ARMADILLO (OHWR0007 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 6-layer board of 64.5 × 43.7 mm with 178 components and 272 nets, published under MIT.

review 90% walked · 11 findings: 6 major · 5 minor (50 items)

Open in the interactive viewerRead the full review

ARMADILLO (OHWR0007 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 11 findings: 6 major · 5 minor (50 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-381majorOpen

    TPS62000 feedback and enable resistors R23, R26, R25, R39: the BOM part numbers contradict the schematic values; built from the part numbers, +1V2 comes out at 0.9 V (below the AT91SAM9263 VDDCORE minimum) and +3V3 at 3.51 V

    The BOM part numbers for the TPS62000 feedback and enable resistors R23, R26, R25 and R39 contradict the schematic values. Built from the part numbers, +1V2 (IC2) comes out at 0.90 V, below the AT91SAM9263 VDDCORE minimum of 1.08 V, and +3V3 (IC8) at 3.51 V.

    Schematic versus BOM

    On the Power supplies sheet (schematic p6) the dividers are drawn as follows. The released BOM carries those values only in its Name column; the Value, LibRef and Manufacturer Part Number columns (and the part number Probe stores) differ.

    ResistorRoleSchematic (and BOM Name)BOM Value / part numberSource
    R23IC2 FB upper, from +1V2165k 1%100k, R0603_100K_1%_0.1W_100PPMschematic p6; released BOM CSV
    R24IC2 FB lower100kR0603_100Kschematic p6; BOM
    R26IC8 FB upper, from +3V3630k 1%680k, R0603_680K_1%_0.1W_100PPMschematic p6; released BOM CSV
    R27IC8 FB lower100kR0603_100Kschematic p6; BOM
    R25, R39EN pull-ups from EXT_VDD_5V to IC2 EN, IC8 EN330k100k, R0603_100K_1%_0.1W_100PPMschematic p6; released BOM CSV

    The outputs

    TPS62000 datasheet (p.5): VO = 0.45 V x (1 + R1/R2), R1 the upper resistor.

    RailWith schematic valuesWith BOM part numbersSource
    +1V2 (IC2)0.45 x (1 + 165/100) = 1.19 V0.45 x (1 + 100/100) = 0.90 Vderived
    +3V3 (IC8)0.45 x (1 + 630/100) = 3.29 V0.45 x (1 + 680/100) = 3.51 Vderived
    AT91SAM9263 VDDCORE range1.08-1.32 VAtmel datasheet, p.6

    +1V2 reaches IC5 balls A16, H10 and V1 (and L2/C67/R23 from IC2).

    Why it matters

    An assembler buying parts by the BOM's part-number column would fit 100k at R23 and 680k at R26.

    • The core rail would sit at about 0.9 V, 0.18 V under the processor's minimum core supply, and the module would not run reliably.
    • The 3.3 V rail would sit at about 3.5 V, still inside most 3.6 V limits but with little margin.

    The schematic values are clearly what the designer meant.

    Fix: correct the part numbers for R23, R25, R39 and R26 in the library or BOM (and L1, whose Name reads "4.7 uH 220 mA" while its Value reads 10mH). For the designer to confirm which values the built boards carry.

  2. DecapViaFanoutmajorOpen

    DecapViaFanout: 3 components×3

    3 checked by the review by Claude walker W4 (Cern session) — 3 different reasons

    At C4, C60, C65

    Each finding, with its own headline
    • C4C4 on 'ACVDD': its rail pad reaches its via over 2.89 mm of track and its ground pad over 0.90 mm, adding about 0.96 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C4 on 'ACVDD': its rail pad reaches its via over 2.89 mm of track and its ground pad over 0.90 mm, adding about 0.96 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C4.1 (rail) runs 2.89 mm along its copper to its nearest via, 1.89 mm past the 1 mm beside the pad: 0.96 nH; C4.2 (ground) runs 0.90 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.96 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.38 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C60C60 on '+3V3': its ground pad over 3.75 mm, adding about 1.08 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C60 on '+3V3': its ground pad over 3.75 mm, adding about 1.08 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C60.2 (rail) not measured: its own track joins it to IC5.K12 (1.03 mm) before any via: it serves that pin directly, and its loop does not run through its vias; C60.1 (ground) runs 3.75 mm along its copper to its nearest via, 2.75 mm past the 1 mm beside the pad: 1.08 nH. Each run past the pad as one conductor of a pair 0.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.08 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.14 nH (pad 0.07 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C65C65 on '+1V2': its rail pad reaches its via over 4.08 mm of track and its ground pad over 0.00 mm, adding about 1.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C65 on '+1V2': its rail pad reaches its via over 4.08 mm of track and its ground pad over 0.00 mm, adding about 1.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C65.2 (rail) runs 4.08 mm along its copper to its nearest via, 3.08 mm past the 1 mm beside the pad: 1.56 nH; C65.1 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.56 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.38 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  3. FiducialMissingmajorOpen

    FiducialMissing: 2 boards×2

    2 checked by the review by evaluation@esharp.se — 2 different reasons

    At bottom, top

    Each finding, with its own headline
    • bottomThe bottom side carries 56 SMT component(s) and no fiducial was found on it

      The bottom side carries 56 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='bottom', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

    • topThe top side carries 120 SMT component(s) and no fiducial was found on it

      The top side carries 120 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

  4. FloatingInputmajorOpen

    IC5.R17 on 'JTCK' has no driver and no pull

    Net 'JTCK': input(s) IC5.R17 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor.

    At JTCK

  5. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 21 boards×21

    21 checked by the review by Claude walker W4 (Cern session) — 21 different reasons

    At along@INTERNALPLANE1:ACGND|GND, along@INTERNALPLANE2:+1V2|+3V3, gap:INTERNALPLANE2:hole 110.21,101.32|117.3,101.58, refchange:+1V2|GND, refchange:+3V3|ETH100_AGND, refchange:+3V3|GND and 15 more

    Each finding, with its own headline
    • along@INTERNALPLANE1:ACGND|GND'PE11' runs ALONG the split between the ACGND and GND planes on INTERNALPLANE1 at 1 place, the longest 1.26 mm; the impedance there is not said (fastest: PE11 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE1 the ACGND and GND planes part, and 'PE11' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. At 1 place(s) the impedance cannot be said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on. No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'PE11' on MIDLAYER1 at (85.08, 98.71), 1.59 mm, running ALONG the split for 1.26 mm, not across it, impedance not said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=along%40INTERNALPLANE1%3AACGND%7CGND serves each with its own layer_image region; all of them lie in x 83.15..86.52, y 97.6..100.14 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • along@INTERNALPLANE2:+1V2|+3V37 nets run ALONG the split between the +1V2 and +3V3 planes on INTERNALPLANE2 at 7 places, the longest 3.46 mm; the impedance rises from 82 ohm to 84 ohm there at worst, 1 % of each edge reflected (fastest: A14 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +1V2 and +3V3 planes part, and 7 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 82 ohm; along the slot 84 ohm, reflecting up to 1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 101 ohm). At 3 place(s) the impedance cannot be said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on. At 4 of the 7 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'PD9' on MIDLAYER2 at (110.03, 104.12), 3.2 mm, running ALONG the split for 2.78 mm, not across it, impedance not said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on; other side: no plane on MIDLAYER1
      • 'PD8' on MIDLAYER2 at (132.85, 107.93), 1.58 mm, running ALONG the split for 1.22 mm, not across it, impedance not said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on; other side: no plane on MIDLAYER1
      • 'PD10' on MIDLAYER2 at (133.46, 108.16), 1.45 mm, running ALONG the split for 1.09 mm, not across it, impedance not said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on; other side: no plane on MIDLAYER1
      • 'D18' on BOTTOM_LAYER at (110.03, 102.37), 1.53 mm, running ALONG the split for 1.13 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'D25' on BOTTOM_LAYER at (110.03, 105.13), 0.89 mm, running ALONG the split for 0.55 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'A14' on BOTTOM_LAYER at (113.99, 98.16), 2.39 mm, running ALONG the split for 2 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'D12' on BOTTOM_LAYER at (115.39, 101.52), 3.99 mm, running ALONG the split for 3.46 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 0.9 % of each edge reflected; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=along%40INTERNALPLANE2%3A%2B1V2%7C%2B3V3 serves each with its own layer_image region; all of them lie in x 108.91..135.01, y 97.02..109.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • gap:INTERNALPLANE2:hole 110.21,101.32|117.3,101.58'PD6' crosses one gap in INTERNALPLANE2's negative-plane field at 1 place, the longest 0.25 mm (fastest: PD6 at 100 ps 10-90 %, ASSUMED)

      Along 'PD6' on MIDLAYER2, INTERNALPLANE2 is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.25 mm under the track at (110.99, 101.45). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. What cleared it: the hole at x 110.21..117.3, y 101.32..101.58. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PD6' on MIDLAYER2 at (110.99, 101.45), 0.25 mm; other side: no plane on MIDLAYER1

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=gap%3AINTERNALPLANE2%3Ahole%20110.21%2C101.32%7C117.3%2C101.58 serves each with its own layer_image region; all of them lie in x 109.99..111.99, y 100.32..102.58 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:+1V2|GND34 nets change reference between +1V2 and GND at 38 vias, none with a reference that continues across (fastest: A16 at 100 ps 10-90 %, ASSUMED)

      At 38 via(s), on 34 net(s), the signal leaves a layer referenced by one of +1V2 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 38 with none. 38 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +1V2 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'PD8' at (110.99, 98.56), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 48.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PD9' at (110.19, 100.16), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 37.9 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PD5' at (110.99, 99.36), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 36.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'D1' at (113.39, 100.16), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 25.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC4_19' at (117.58, 85.8), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 19.1 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C49 (22 uF 1206) 2.3 mm away: 1.12 nH in the 0.960 mm cavity + 0.80 nH ESL + 0.97 nH mounting (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 90.6 ohm at the knee, 181 % of 50 ohm (assumed track impedance). None.
      • 'D12' at (111.79, 99.36), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 18.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'D11' at (111.79, 100.16), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 16.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC5_N16' at (104.67, 105.71), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 16.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C36 (22 uF 1206) 1.9 mm away: 1.05 nH in the 0.960 mm cavity + 0.80 nH ESL + 0.97 nH mounting (pad 0.20 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 88.5 ohm at the knee, 177 % of 50 ohm (assumed track impedance). None.
      • 'D14' at (110.99, 100.16), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 15.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'D25' at (107.79, 96.96), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 14.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'D31' at (107.79, 98.56), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 13.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'D29' at (107.77, 97.76), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +1V2 on INTERNALPLANE2; pure, no reference continues across; stitching none, 13.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +1V2 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 26 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3A%2B1V2%7CGND serves each with its own layer_image region; all of them lie in x 102.67..141.5, y 83.8..108.98 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:+3V3|ETH100_AGND15 nets change reference between +3V3 and ETH100_AGND at 18 vias, none with a reference that continues across (fastest: NetIC4_12 at 100 ps 10-90 %, ASSUMED)

      At 18 via(s), on 15 net(s), the signal leaves a layer referenced by one of +3V3 and ETH100_AGND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 18 with none. 18 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V3 and ETH100_AGND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'NRST' at (102.26, 79.17), MIDLAYER1 -> MIDLAYER2: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NRST' at (134.11, 80.75), MIDLAYER1 -> MIDLAYER2: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC0' at (134.39, 86.18), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 7.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC4' at (134.82, 89.59), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC10' at (134.87, 88.34), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC2' at (135.08, 87.17), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC8' at (134.04, 89.84), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 3.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC13' at (134.19, 88.01), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 3.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC3' at (134.34, 88.93), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 2.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PC18' at (134.52, 86.79), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 2.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC4_13' at (123.39, 82.12), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 2.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC4_13' at (133.71, 79.96), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 2.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and ETH100_AGND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 6 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3A%2B3V3%7CETH100_AGND serves each with its own layer_image region; all of them lie in x 100.26..137.15, y 74.71..91.84 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:+3V3|GND118 nets change reference between +3V3 and GND at 174 vias, none with a reference that continues across (fastest: A0 at 100 ps 10-90 %, ASSUMED)

      At 174 via(s), on 118 net(s), the signal leaves a layer referenced by one of +3V3 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 174 with none. 174 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V3 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'PD10' at (110.99, 97.76), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 50.7 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C50 (100 nF 0402) 2.1 mm away: 1.08 nH in the 0.960 mm cavity + 0.30 nH ESL + 0.84 nH mounting (pad 0.07 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 69.7 ohm at the knee, 139 % of 50 ohm (assumed track impedance). None.
      • 'NRST' at (102.26, 79.17), MIDLAYER1 -> MIDLAYER2: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NRST' at (134.11, 80.75), MIDLAYER1 -> MIDLAYER2: GND on INTERNALPLANE1, ETH100_AGND on MIDLAYER2 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NRST' at (100.28, 91.19), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C48 (22 uF 1206) 2.7 mm away: 1.18 nH in the 0.960 mm cavity + 0.80 nH ESL + 0.97 nH mounting (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 92.5 ohm at the knee, 185 % of 50 ohm (assumed track impedance). None.
      • 'NetCN1_G4' at (93.24, 78.87), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 38.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetCN1_G4' at (106.6, 102.79), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 38.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PD7' at (110.9, 103.51), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 33.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C47 (22 uF 1206) 2.1 mm away: 1.08 nH in the 0.960 mm cavity + 0.80 nH ESL + 0.97 nH mounting (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 89.6 ohm at the knee, 179 % of 50 ohm (assumed track impedance). None.
      • 'NetIC4_38' at (102.18, 91.34), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 26.8 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC4_38' at (119.56, 76.99), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 26.8 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC5_M17' at (104.19, 107.82), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 24.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC5_M17' at (106.73, 87.58), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 24.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC4_29' at (102.99, 91.36), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to +3V3 on INTERNALPLANE2; pure, no reference continues across; stitching none, 24.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 162 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3A%2B3V3%7CGND serves each with its own layer_image region; all of them lie in x 86.34..141.37, y 73.79..113.84 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:ACGND|ACVDD5 nets change reference between ACGND and ACVDD at 5 vias, none with a reference that continues across (fastest: AUDIO_HPOUT_L at 100 ps 10-90 %, ASSUMED)

      At 5 via(s), on 5 net(s), the signal leaves a layer referenced by one of ACGND and ACVDD for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 5 with none. 5 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether ACGND and ACVDD are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'AUDIO_MIC_IN' at (84.79, 109.75), TOP_LAYER -> BOTTOM_LAYER: ACGND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 19.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACGND and ACVDD are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C14 (100 nF 0603) 1.1 mm away: 0.82 nH in the 0.960 mm cavity + 0.51 nH ESL + 0.87 nH mounting (pad 0.10 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 69.0 ohm at the knee, 138 % of 50 ohm (assumed track impedance). None.
      • 'NetC16_1' at (95.05, 105.51), TOP_LAYER -> BOTTOM_LAYER: ACGND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACGND and ACVDD are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetC17_1' at (94.26, 104.78), TOP_LAYER -> BOTTOM_LAYER: ACGND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACGND and ACVDD are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'AUDIO_HPOUT_L' at (84.4, 111.18), TOP_LAYER -> BOTTOM_LAYER: ACGND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACGND and ACVDD are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C14 (100 nF 0603) 1.8 mm away: 1.01 nH in the 0.960 mm cavity + 0.51 nH ESL + 0.87 nH mounting (pad 0.10 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED): 75.0 ohm at the knee, 150 % of 50 ohm (assumed track impedance). None.
      • 'AUDIO_HPOUT_R' at (81.25, 111.81), TOP_LAYER -> BOTTOM_LAYER: ACGND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACGND and ACVDD are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3AACGND%7CACVDD serves each with its own layer_image region; all of them lie in x 79.25..97.05, y 102.78..113.81 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:ACVDD|GND5 nets change reference between ACVDD and GND at 5 vias, none with a reference that continues across (fastest: PE0 at 100 ps 10-90 %, ASSUMED)

      At 5 via(s), on 5 net(s), the signal leaves a layer referenced by one of ACVDD and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 5 with none. 5 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether ACVDD and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'PE0' at (81.15, 101.65), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACVDD and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PE1' at (81.18, 100.41), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACVDD and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PE10' at (81.23, 102.9), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACVDD and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PE6' at (81.25, 105.46), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACVDD and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PE4' at (81.25, 104.22), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to ACVDD on INTERNALPLANE2; pure, no reference continues across; stitching none, 1.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. ACVDD and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3AACVDD%7CGND serves each with its own layer_image region; all of them lie in x 79.15..83.25, y 98.41..107.46 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:EXT_VDD_5V|GND39 nets change reference between EXT_VDD_5V and GND at 43 vias, none with a reference that continues across (fastest: NetIC2_4 at 100 ps 10-90 %, ASSUMED)

      At 43 via(s), on 39 net(s), the signal leaves a layer referenced by one of EXT_VDD_5V and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 43 with none. 43 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether EXT_VDD_5V and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'NRST' at (138.61, 97.28), TOP_LAYER -> MIDLAYER2: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NRST' at (142.95, 104.88), MIDLAYER1 -> MIDLAYER2: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 42.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB16' at (81.33, 86.39), TOP_LAYER -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 16.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'USB_HOST_B_N' at (84.71, 78.82), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 16.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'USB_HOST_B_N' at (91.52, 76.53), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 16.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'USB_HOST_B_P' at (84.73, 77.55), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 15.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'USB_HOST_B_P' at (91.49, 75.82), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 15.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB9' at (91.08, 85.17), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 8.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB10' at (90.5, 85.17), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 7.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB6' at (90.5, 83.52), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB8' at (90.98, 83.11), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 6.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PB5' at (90.5, 82.65), MIDLAYER1 -> BOTTOM_LAYER: GND on INTERNALPLANE1 to EXT_VDD_5V on INTERNALPLANE2; pure, no reference continues across; stitching none, 5.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. EXT_VDD_5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 31 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=refchange%3AEXT_VDD_5V%7CGND serves each with its own layer_image region; all of them lie in x 79.13..145.26, y 73.57..112.67 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INTERNALPLANE1:ACGND|GND9 nets cross the split between the ACGND and GND planes on INTERNALPLANE1 at 15 places, with no plane on the track's other side (fastest: AUDIO_HPOUT_R at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE1 the ACGND and GND planes part, and 9 nets cross from one to the other at 15 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 15 crossing(s) the track's other neighbour carries a plane, which the return can use there; 5 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'AUDIO_HPOUT_R' on TOP_LAYER at (81.75, 108.56), 0.25 mm; other side: none: the signal layer is outermost
      • 'AUDIO_HPOUT_R' on TOP_LAYER at (83.92, 103.45), 0.25 mm; other side: none: the signal layer is outermost
      • 'NetC17_1' on TOP_LAYER at (96.06, 104.81), 0.17 mm; other side: none: the signal layer is outermost
      • 'NetC1_1' on TOP_LAYER at (83.88, 100.64), 0.29 mm; other side: none: the signal layer is outermost
      • 'NetC2_1' on TOP_LAYER at (83.92, 105.05), 0.36 mm; other side: none: the signal layer is outermost
      • 'PE0' on MIDLAYER1 at (83.92, 102.67), 0.36 mm; other side: no plane on MIDLAYER2
      • 'PE0' on MIDLAYER1 at (100.08, 105.16), 0.31 mm; other side: no plane on MIDLAYER2
      • 'PE1' on MIDLAYER1 at (83.92, 100.38), 0.25 mm; other side: no plane on MIDLAYER2
      • 'PE1' on MIDLAYER1 at (85.93, 98.73), 0.36 mm; other side: no plane on MIDLAYER2
      • 'PE10' on MIDLAYER1 at (83.92, 103.35), 0.36 mm; other side: no plane on MIDLAYER2
      • 'PE10' on MIDLAYER1 at (100.24, 105.32), 0.25 mm; other side: no plane on MIDLAYER2
      • 'PE4' on MIDLAYER1 at (83.92, 106.2), 0.36 mm; other side: no plane on MIDLAYER2
      • and 3 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=split%40INTERNALPLANE1%3AACGND%7CGND serves each with its own layer_image region; all of them lie in x 80.75..101.68, y 97.6..109.69 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INTERNALPLANE2:+1V2|+3V331 nets cross the split between the +1V2 and +3V3 planes on INTERNALPLANE2 at 45 places, with no plane on the track's other side (fastest: A16 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +1V2 and +3V3 planes part, and 31 nets cross from one to the other at 45 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 45 crossing(s) the track's other neighbour carries a plane, which the return can use there; 35 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A16' on BOTTOM_LAYER at (112.18, 98.15), 0.36 mm; other side: none: the signal layer is outermost
      • 'D0' on BOTTOM_LAYER at (128.8, 108.05), 0.25 mm; other side: none: the signal layer is outermost
      • 'D1' on BOTTOM_LAYER at (129.21, 108.05), 0.25 mm; other side: none: the signal layer is outermost
      • 'D11' on BOTTOM_LAYER at (111.53, 101.45), 0.36 mm; other side: none: the signal layer is outermost
      • 'D12' on BOTTOM_LAYER at (119.05, 102.44), 0.36 mm; other side: none: the signal layer is outermost
      • 'D12' on BOTTOM_LAYER at (121.5, 102.57), 0.36 mm; other side: none: the signal layer is outermost
      • 'D12' on BOTTOM_LAYER at (122.84, 103.92), 0.36 mm; other side: none: the signal layer is outermost
      • 'D14' on BOTTOM_LAYER at (110.74, 101.45), 0.36 mm; other side: none: the signal layer is outermost
      • 'D16' on BOTTOM_LAYER at (110.44, 101.47), 0.34 mm; other side: none: the signal layer is outermost
      • 'D16' on BOTTOM_LAYER at (110.52, 98.09), 0.31 mm; other side: none: the signal layer is outermost
      • 'D19' on BOTTOM_LAYER at (110.03, 103.23), 0.36 mm; other side: none: the signal layer is outermost
      • 'D2' on BOTTOM_LAYER at (129.62, 108.04), 0.26 mm; other side: none: the signal layer is outermost
      • and 33 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=split%40INTERNALPLANE2%3A%2B1V2%7C%2B3V3 serves each with its own layer_image region; all of them lie in x 102.43..132.98, y 84.14..109.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INTERNALPLANE2:+1V2|EXT_VDD_5V7 nets cross the split between the +1V2 and EXT_VDD_5V planes on INTERNALPLANE2 at 9 places, with no plane on the track's other side (fastest: NetIC2_4 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +1V2 and EXT_VDD_5V planes part, and 7 nets cross from one to the other at 9 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 9 crossing(s) the track's other neighbour carries a plane, which the return can use there; 4 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'DTXD' on BOTTOM_LAYER at (141.48, 102.92), 0.25 mm; other side: none: the signal layer is outermost
      • 'NRST' on BOTTOM_LAYER at (134.77, 111.15), 0.38 mm; other side: none: the signal layer is outermost
      • 'NRST' on MIDLAYER2 at (141.15, 102.11), 0.36 mm; other side: no plane on MIDLAYER1
      • 'NRST' on MIDLAYER2 at (141.48, 103.4), 0.36 mm; other side: no plane on MIDLAYER1
      • 'NetIC2_4' on BOTTOM_LAYER at (138.65, 107.75), 0.36 mm; other side: none: the signal layer is outermost
      • 'PD10' on MIDLAYER2 at (139.29, 107.11), 0.36 mm; other side: no plane on MIDLAYER1
      • 'PD3' on BOTTOM_LAYER at (141.48, 104.19), 0.25 mm; other side: none: the signal layer is outermost
      • 'PD6' on MIDLAYER2 at (140.98, 105.43), 0.36 mm; other side: no plane on MIDLAYER1
      • 'PD8' on MIDLAYER2 at (139.67, 106.73), 0.36 mm; other side: no plane on MIDLAYER1

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=split%40INTERNALPLANE2%3A%2B1V2%7CEXT_VDD_5V serves each with its own layer_image region; all of them lie in x 133.62..142.61, y 100.93..112.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INTERNALPLANE2:+3V3|ACVDD16 nets cross the split between the +3V3 and ACVDD planes on INTERNALPLANE2 at 32 places, with no plane on the track's other side (fastest: AUDIO_MIC_IN at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +3V3 and ACVDD planes part, and 16 nets cross from one to the other at 32 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 32 crossing(s) the track's other neighbour carries a plane, which the return can use there; 22 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'AUDIO_MIC_IN' on BOTTOM_LAYER at (97.97, 104.06), 0.25 mm; other side: none: the signal layer is outermost
      • 'NetC16_1' on BOTTOM_LAYER at (97.92, 106.35), 0.3 mm; other side: none: the signal layer is outermost
      • 'NetC16_1' on BOTTOM_LAYER at (97.97, 108.31), 0.36 mm; other side: none: the signal layer is outermost
      • 'NetC16_2' on BOTTOM_LAYER at (99.05, 109.98), 0.25 mm; other side: none: the signal layer is outermost
      • 'NetIC1_6' on BOTTOM_LAYER at (96.16, 98.4), 0.25 mm; other side: none: the signal layer is outermost
      • 'NetIC1_6' on BOTTOM_LAYER at (99.77, 97.1), 0.28 mm; other side: none: the signal layer is outermost
      • 'PA26' on BOTTOM_LAYER at (91.54, 99.98), 0.36 mm; other side: none: the signal layer is outermost
      • 'PA26' on BOTTOM_LAYER at (96.16, 99.16), 0.25 mm; other side: none: the signal layer is outermost
      • 'PA27' on BOTTOM_LAYER at (94.14, 100.51), 0.25 mm; other side: none: the signal layer is outermost
      • 'PA27' on BOTTOM_LAYER at (96.16, 100.13), 0.25 mm; other side: none: the signal layer is outermost
      • 'PA27' on BOTTOM_LAYER at (97.97, 100.13), 0.25 mm; other side: none: the signal layer is outermost
      • 'PA28' on BOTTOM_LAYER at (96.16, 99.45), 0.25 mm; other side: none: the signal layer is outermost
      • and 20 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=split%40INTERNALPLANE2%3A%2B3V3%7CACVDD serves each with its own layer_image region; all of them lie in x 87.52..100.92, y 95.57..111.11 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INTERNALPLANE2:+3V3|EXT_VDD_5V12 nets cross the split between the +3V3 and EXT_VDD_5V planes on INTERNALPLANE2 at 14 places, with no plane on the track's other side (fastest: NetIC1_5 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +3V3 and EXT_VDD_5V planes part, and 12 nets cross from one to the other at 14 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 14 crossing(s) the track's other neighbour carries a plane, which the return can use there; 13 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ETH_RX-' on BOTTOM_LAYER at (140.08, 77.52), 0.36 mm; other side: none: the signal layer is outermost
      • 'NRST' on MIDLAYER2 at (137.16, 93.73), 0.25 mm; other side: no plane on MIDLAYER1
      • 'NetIC1_5' on BOTTOM_LAYER at (90.88, 94.11), 0.3 mm; other side: none: the signal layer is outermost
      • 'NetIC1_5' on BOTTOM_LAYER at (90.88, 95.48), 0.25 mm; other side: none: the signal layer is outermost
      • 'PB11' on BOTTOM_LAYER at (89.77, 90.88), 0.36 mm; other side: none: the signal layer is outermost
      • 'PB11' on BOTTOM_LAYER at (92.15, 85.57), 0.25 mm; other side: none: the signal layer is outermost
      • 'PC11' on BOTTOM_LAYER at (133.45, 97.84), 0.25 mm; other side: none: the signal layer is outermost
      • 'PC9' on BOTTOM_LAYER at (135.97, 93.73), 0.36 mm; other side: none: the signal layer is outermost
      • 'PE14' on BOTTOM_LAYER at (87.1, 96.57), 0.25 mm; other side: none: the signal layer is outermost
      • 'PE15' on BOTTOM_LAYER at (87.1, 97.84), 0.25 mm; other side: none: the signal layer is outermost
      • 'PE8' on BOTTOM_LAYER at (88.28, 94.03), 0.45 mm; other side: none: the signal layer is outermost
      • 'USB_HOST_A_N' on BOTTOM_LAYER at (92.15, 77.83), 0.25 mm; other side: none: the signal layer is outermost
      • and 2 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=split%40INTERNALPLANE2%3A%2B3V3%7CEXT_VDD_5V serves each with its own layer_image region; all of them lie in x 85.97..141.26, y 74.82..98.84 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:EXT_VDD_5V@INTERNALPLANE2:hole 132.77,95.91|133.38,96.52'PC6' crosses one void in the EXT_VDD_5V plane on INTERNALPLANE2 at 1 place, the longest 0.51 mm (fastest: PC6 at 100 ps 10-90 %, ASSUMED)

      Along 'PC6' on BOTTOM_LAYER, the EXT_VDD_5V plane on INTERNALPLANE2 has 0.51 mm under the track with no copper, at (133.22, 96.22), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 132.77..133.38, y 95.91..96.52. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PC6' on BOTTOM_LAYER at (133.22, 96.22), 0.51 mm over no copper, to the end of the track; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AEXT_VDD_5V%40INTERNALPLANE2%3Ahole%20132.77%2C95.91%7C133.38%2C96.52 serves each with its own layer_image region; all of them lie in x 132.07..134.58, y 95.22..97.22 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 133.58,89.05|136.12,91.59'PC5' crosses one void in the GND plane on INTERNALPLANE1 at 1 place, the longest 0.25 mm (fastest: PC5 at 100 ps 10-90 %, ASSUMED)

      Along 'PC5' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 0.25 mm under the track with no copper, at (134.35, 90.82), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 133.58..136.12, y 89.05..91.59. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PC5' on MIDLAYER1 at (134.35, 90.82), 0.25 mm over no copper; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20133.58%2C89.05%7C136.12%2C91.59 serves each with its own layer_image region; all of them lie in x 133.26..135.44, y 89.73..91.91 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 133.58,91.34|133.83,98.936 nets cross one void in the GND plane on INTERNALPLANE1 at 6 places, the longest 1.15 mm (fastest: PC12 at 100 ps 10-90 %, ASSUMED)

      Along 'PC12' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 1.15 mm under the track with no copper, at (133.63, 91.9), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.76 mm). 6 places on 6 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 133.58..133.83, y 91.34..98.93. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PC12' on MIDLAYER1 at (133.63, 91.9), 1.15 mm, running ALONG the bare copper for 0.76 mm, not across it over no copper; other side: no plane on MIDLAYER2
      • 'PC14' on MIDLAYER1 at (133.71, 95.53), 0.36 mm over no copper; other side: no plane on MIDLAYER2
      • 'PC17' on MIDLAYER1 at (133.71, 96.01), 0.36 mm over no copper; other side: no plane on MIDLAYER2
      • 'DRXD' on MIDLAYER1 at (133.71, 97.83), 0.25 mm over no copper; other side: no plane on MIDLAYER2
      • 'PC16' on MIDLAYER1 at (133.71, 93.77), 0.25 mm over no copper; other side: no plane on MIDLAYER2
      • 'PD0' on MIDLAYER1 at (133.71, 96.62), 0.25 mm over no copper; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20133.58%2C91.34%7C133.83%2C98.93 serves each with its own layer_image region; all of them lie in x 132.58..134.83, y 90.36..98.83 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 133.71,98.32|134.32,98.93'PC20' crosses one void in the GND plane on INTERNALPLANE1 at 1 place, the longest 0.44 mm (fastest: PC20 at 100 ps 10-90 %, ASSUMED)

      Along 'PC20' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 0.44 mm under the track with no copper, at (133.85, 98.65), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 133.71..134.32, y 98.32..98.93. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PC20' on MIDLAYER1 at (133.85, 98.65), 0.44 mm over no copper, to the end of the track; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20133.71%2C98.32%7C134.32%2C98.93 serves each with its own layer_image region; all of them lie in x 132.58..135.01, y 97.63..99.65 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 133.73,93.07|134.34,93.68'PC9' crosses one void in the GND plane on INTERNALPLANE1 at 1 place, the longest 0.46 mm (fastest: PC9 at 100 ps 10-90 %, ASSUMED)

      Along 'PC9' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 0.46 mm under the track with no copper, at (133.88, 93.37), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 133.73..134.34, y 93.07..93.68. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PC9' on MIDLAYER1 at (133.88, 93.37), 0.46 mm over no copper, to the end of the track; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20133.73%2C93.07%7C134.34%2C93.68 serves each with its own layer_image region; all of them lie in x 132.58..135.04, y 92.37..94.37 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 134.44,104.19|134.7,115.55'PD3' crosses one void in the GND plane on INTERNALPLANE1 at 1 place, the longest 0.25 mm (fastest: PD3 at 100 ps 10-90 %, ASSUMED)

      Along 'PD3' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 0.25 mm under the track with no copper, at (134.57, 104.55), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 134.44..134.7, y 104.19..115.55. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PD3' on MIDLAYER1 at (134.57, 104.55), 0.25 mm over no copper; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20134.44%2C104.19%7C134.7%2C115.55 serves each with its own layer_image region; all of them lie in x 133.44..135.7, y 103.55..105.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@INTERNALPLANE1:hole 134.49,104.14|139.42,104.392 nets cross one void in the GND plane on INTERNALPLANE1 at 2 places, the longest 3.71 mm (fastest: PD3 at 100 ps 10-90 %, ASSUMED)

      Along 'DTXD' on MIDLAYER1, the GND plane on INTERNALPLANE1 has 3.71 mm under the track with no copper, at (136.2, 104.32), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 3.25 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 134.49..139.42, y 104.14..104.39. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'DTXD' on MIDLAYER1 at (136.2, 104.32), 3.71 mm, running ALONG the bare copper for 3.25 mm, not across it over no copper; other side: no plane on MIDLAYER2
      • 'PD3' on MIDLAYER1 at (138.43, 104.27), 0.36 mm over no copper; other side: no plane on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AGND%40INTERNALPLANE1%3Ahole%20134.49%2C104.14%7C139.42%2C104.39 serves each with its own layer_image region; all of them lie in x 133.44..139.56, y 103.14..105.39 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  6. SinglePointNetmajorOpen

    SinglePointNet: 9 pins×9

    Checked by the review, stands · Claude walker (cern session) — AD1981B IC1 unused analog inputs (PHONE_IN, AUX_L/R, CD_L/CD_GND_REF/CD_R, MIC2) and chip-select inputs ID0/ID1 (45/46) are open (netlist). The datasheet pin table (p.10-11) does not say whether unused inputs may be left open, nor state an internal pull on ID0/ID1, so left checked.

    At IC1.13, IC1.14, IC1.15, IC1.18, IC1.19, IC1.20 and 3 more

    Each finding, with its own headline
    • IC1.13IC1.13 (PHONE_IN) is an IC input left unconnected

      Pin IC1.13 (PHONE_IN) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.14IC1.14 (AUX_L) is an IC input left unconnected

      Pin IC1.14 (AUX_L) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.15IC1.15 (AUX_R) is an IC input left unconnected

      Pin IC1.15 (AUX_R) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.18IC1.18 (CD_L) is an IC input left unconnected

      Pin IC1.18 (CD_L) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.19IC1.19 (CD_GND_REF) is an IC input left unconnected

      Pin IC1.19 (CD_GND_REF) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.20IC1.20 (CD_R) is an IC input left unconnected

      Pin IC1.20 (CD_R) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.22IC1.22 (MIC2) is an IC input left unconnected

      Pin IC1.22 (MIC2) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.45IC1.45 (ID0) is an IC input left unconnected

      Pin IC1.45 (ID0) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC1.46IC1.46 (ID1) is an IC input left unconnected

      Pin IC1.46 (ID1) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

  7. observationOBS-383minorOpen

    AT91SAM9263 JTAG port is not reachable: JTDO, JTCK, JTDI, JTMS, JNTRST and JRTCK end on IC5 and the RP4 pull-ups, with no connector contact, header or test point, and TCK has no defined level

    The AT91SAM9263 (IC5) JTAG port is not reachable: JTDO, JTCK, JTDI, JTMS, JNTRST and JRTCK end on IC5 and the RP4 pull-ups, with no connector contact, header or test point, and TCK has no defined level.

    The nets

    NetIC5 ballOther membersSource
    JTDIP17 (TDI)RP4.3, 10k to +3V3netlist
    JTDON18 (TDO)nonenetlist
    JTMSN17 (TMS)RP4.4, 10k to +3V3netlist
    JTCKR17 (TCK)nonenetlist
    JNTRSTU16 (NTRST)RP4.2, 10k to +3V3netlist
    JRTCKU15 (RTCK)RP4.1, 10k to +3V3netlist
    JTAGSELP5R18 (0R, fitted) to +1V2netlist

    RP4 pins 5-8 are on +3V3. None of the six nets reaches CN2, CN3, a test point or any other component. The top-level sheet (schematic p5) draws the U_CPU_io_ports sheet symbol's JTDO/TDI/TMS/TCK/NTRST/RTCK ports out to net labels JTDO...JRTCK that connect to nothing else. CN2/CN3 carry USB, PIO, audio, Ethernet, NRST, PSU_EN and 5 V.

    What the datasheet says (Atmel AT91SAM9263, p.17)

    • "TMS, TDI and TCK are Schmitt trigger inputs and have no pull-up resistors", so JTCK floats.
    • JTAGSEL high selects boundary scan rather than ICE debug. JTAGSEL integrates a pull-down "so that it can be left unconnected for normal operations".

    Why it matters

    With no access to TDI, TDO, TCK and TMS there is no in-circuit debug or boundary-scan test of the module, which matters for bring-up and board test. JTAGSEL strapped high suggests boundary scan was intended, which makes the missing access look like an oversight rather than a choice.

    The floating TCK is harmless while TMS is pulled high (the TAP stays in Test-Logic-Reset), but it is an undefined CMOS input.

    For the designer to confirm whether JTAG access exists as bare pads that the component netlist does not show, or whether the labels on the top sheet were meant to reach CN2/CN3.

  8. observationOBS-393minorOpen

    Bottom silkscreen: designators of the USB pull-downs R40, R43, R44 and R47 are printed on top of each other, and the R40 text runs over a pad of C70

    On the bottom silkscreen the designators of the USB pull-downs R40, R43, R44 and R47 are printed on top of each other, and the R40 text runs over a paste pad of C70.

    Where it is

    The four are 15k USB host D+/D- pull-downs, all bottom side at x 105.664 mm on a 1.5 mm pitch:

    • R43 at (105.664, 75.692)
    • R40 at (105.664, 77.343)
    • R47 at (105.664, 78.867)
    • R44 at (105.664, 80.391)
    • C70 at (109.118, 76.429), C71 at (110.642, 76.429)

    Rendered from the ODB++ bottom overlay and bottom paste at 75 px/mm (region x 96-112, y 72-82), the texts overlap and read as "RR4R43" and a garbled "R40/R4" block. The R40 glyphs also overlap one of the paste pads beside C70/C71.

    Why it matters

    Superimposed designators cannot be read at assembly, rework or inspection, so the four near-identical resistors cannot be told apart by their silk. Silk ink on a pad can lift or mask a solder joint, depending on whether the fab clips silk to the solder-mask opening.

    Fix: move the designators apart and clear of the pads.

  9. observationOBS-477minorOpen

    No fiducials on the ARMADILLO: neither global fiducials nor a local pair for the 0.8 mm-pitch TFBGA324 AT91SAM9263 (IC5) is present in the ODB++

    The ARMADILLO has no fiducials on either side: no global fiducials, and no local pair at the 0.8 mm-pitch TFBGA324 processor IC5 (AT91SAM9263). The pick-and-place machine has nothing designed-in to align on for the finest-pitch part on a double-sided board.

    What was checked

    • The ODB++ export has no pad with fiducial usage (.pad_usage g_fiducial or l_fiducial) and no component that reads as a fiducial by refdes or part name, on either side.
    • The job is a single board step, not a panel (no step-repeat), so no panel-frame fiducials are in the data either.
    • The full-board top and bottom renders (copper, paste, silk) show no fiducial marks.

    What is on each side

    SideFine-pitch or large partsSource
    TopIC5 AT91SAM9263-CU, TFBGA324, 0.8 mm ball pitchplacement; AT91SAM9263 datasheet p.4
    TopIC7 SDRAM MT48LC16M16A2, TSOP54placement
    TopIC10 AT45DB642D DataFlash, TSOP28placement
    TopIC1 AD1981B and IC4 DM9161AEP, LQFP48placement
    BottomIC6 SDRAM MT48LC16M16A2, TSOP54placement
    BottomCN2, CN3, 60-way 1.27 mm board-to-board headers (PBHTD60S)placement, BOM
    QuantityValueSource
    Fiducials found, top / bottom0 / 0ODB++ scan (placement, layer_image)
    Board sizeabout 64.5 x 43.7 mmODB++ outline
    IC5 ball pitch0.8 mmAT91SAM9263 datasheet p.4

    Why it matters

    Placing a 0.8 mm BGA and TSOPs on both sides normally relies on two or three global fiducials per side, and often a local pair at the BGA. Without them the assembler has to align on pads or on fiducials added to a panel frame, which is less accurate and is not under the designer's control.

    What would close it

    The designer or assembler confirming how the board was aligned, for example on a panel with its own fiducials. Otherwise add at least three global fiducials per side and consider a local pair at IC5.

  10. DecapViaFanoutminorOpen

    DecapViaFanout: 5 components×5

    5 checked by the review by Claude walker W4 (Cern session) — 5 different reasons

    At C136, C21, C35, C49, C67

    Each finding, with its own headline
    • C136C136 on '+3V3': its rail pad reaches its via over 0.86 mm of track and its ground pad over 2.43 mm, adding about 0.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C136 on '+3V3': its rail pad reaches its via over 0.86 mm of track and its ground pad over 2.43 mm, adding about 0.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C136.2 (rail) runs 0.86 mm along its copper to its nearest via, beside the pad; C136.1 (ground) runs 2.43 mm along its copper to its nearest via, 1.43 mm past the 1 mm beside the pad: 0.56 nH. Each run past the pad as one conductor of a pair 0.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.56 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.32 nH (pad 0.07 nH (vias beside the pads) + 1 via pair(s) at 0.64 mm pitch, 0.20 mm drill, 1.28 mm to the farther plane). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C21C21 on 'ACVDD': its rail pad reaches its via over 1.83 mm of track and its ground pad over 1.58 mm, adding about 0.88 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 100 uF bulk capacitor: its inductance matters only far above the band it serves)

      C21 on 'ACVDD': its rail pad reaches its via over 1.83 mm of track and its ground pad over 1.58 mm, adding about 0.88 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 100 uF bulk capacitor: its inductance matters only far above the band it serves). C21.1 (rail) runs 1.83 mm along its copper to its nearest via, 0.83 mm past the 1 mm beside the pad: 0.52 nH; C21.2 (ground) runs 1.58 mm along its copper to its nearest via, 0.58 mm past the 1 mm beside the pad: 0.36 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.88 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.77 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C35C35 on '+3V3': its rail pad reaches its via over 1.99 mm of track and its ground pad over 1.24 mm, adding about 0.74 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C35 on '+3V3': its rail pad reaches its via over 1.99 mm of track and its ground pad over 1.24 mm, adding about 0.74 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C35.1 (rail) runs 1.99 mm along its copper to its nearest via, 0.99 mm past the 1 mm beside the pad: 0.60 nH; C35.2 (ground) runs 1.24 mm along its copper to its nearest via, 0.24 mm past the 1 mm beside the pad: 0.14 nH. Each run past the pad as one conductor of a pair 2.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.74 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.77 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C49C49 on '+1V2': its rail pad reaches its via over 2.01 mm of track and its ground pad over 1.65 mm, adding about 1.00 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 22 uF bulk capacitor: its inductance matters only far above the band it serves)

      C49 on '+1V2': its rail pad reaches its via over 2.01 mm of track and its ground pad over 1.65 mm, adding about 1.00 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 22 uF bulk capacitor: its inductance matters only far above the band it serves). C49.1 (rail) runs 2.01 mm along its copper to its nearest via, 1.01 mm past the 1 mm beside the pad: 0.61 nH; C49.2 (ground) runs 1.65 mm along its copper to its nearest via, 0.65 mm past the 1 mm beside the pad: 0.39 nH. Each run past the pad as one conductor of a pair 2.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.00 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.77 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C67C67 on '+1V2': its rail pad reaches its via over 1.44 mm of track and its ground pad over 1.64 mm, adding about 0.68 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C67 on '+1V2': its rail pad reaches its via over 1.44 mm of track and its ground pad over 1.64 mm, adding about 0.68 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C67.1 (rail) runs 1.44 mm along its copper to its nearest via, 0.44 mm past the 1 mm beside the pad: 0.28 nH; C67.2 (ground) runs 1.64 mm along its copper to its nearest via, 0.64 mm past the 1 mm beside the pad: 0.40 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.68 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.77 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.28 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  11. ReferencePlaneDiscontinuityminorOpen

    ReferencePlaneDiscontinuity: 5 boards×5

    5 checked by the review by Claude walker W4 (Cern session) — 5 different reasons

    At along@INTERNALPLANE2:+3V3|ACVDD, along@INTERNALPLANE2:+3V3|EXT_VDD_5V, void:ETH100_AGND@MIDLAYER2:134.4,85.17, void:ETH100_AGND@MIDLAYER2:134.49,87.2, void:routed@MIDLAYER1|MIDLAYER2

    Each finding, with its own headline
    • along@INTERNALPLANE2:+3V3|ACVDD4 nets run ALONG the split between the +3V3 and ACVDD planes on INTERNALPLANE2 at 4 places, the longest 1.92 mm; the impedance rises from 82 ohm to 84 ohm there at worst, 1 % of each edge reflected (fastest: PA26 at 100 ps 10-90 %, ASSUMED)

      On INTERNALPLANE2 the +3V3 and ACVDD planes part, and 4 nets run down the slot between them at 4 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 82 ohm; along the slot 83 ohm, reflecting up to 1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 101 ohm). At every place the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is the lower tier (info). One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'PA26' on BOTTOM_LAYER at (99.22, 98.69), 1.76 mm, running ALONG the split for 1.47 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'WKUP' on BOTTOM_LAYER at (90.53, 99.51), 1.74 mm, running ALONG the split for 1.37 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'PA28' on BOTTOM_LAYER at (92.73, 100.21), 2.3 mm, running ALONG the split for 1.92 mm, not across it, 82 ohm over solid plane, 84 ohm along it: 1 % of each edge reflected; other side: none: the signal layer is outermost
      • 'PE9' on BOTTOM_LAYER at (87.44, 99.11), 1.29 mm, running ALONG the split for 1.04 mm, not across it, 82 ohm over solid plane, 83 ohm along it: 0.9 % of each edge reflected; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=along%40INTERNALPLANE2%3A%2B3V3%7CACVDD serves each with its own layer_image region; all of them lie in x 85.78..100.92, y 97.12..101.21 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • along@INTERNALPLANE2:+3V3|EXT_VDD_5V'USB_HOST_B_N' runs ALONG the split between the +3V3 and EXT_VDD_5V planes on INTERNALPLANE2 at 1 place, the longest 0.54 mm; the impedance rises from 69 ohm to 71 ohm there at worst, 1.1 % of each edge reflected (fastest: USB_HOST_B_N at 500 ps 10-90 %, suggested by its name)

      On INTERNALPLANE2 the +3V3 and EXT_VDD_5V planes part, and 'USB_HOST_B_N' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 69 ohm; along the slot 71 ohm, reflecting up to 1.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 88 ohm). At every place the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is the lower tier (info). One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'USB_HOST_B_N' on BOTTOM_LAYER at (92.27, 76.37), 0.8 mm, running ALONG the split for 0.54 mm, not across it, 69 ohm over solid plane, 71 ohm along it: 1.1 % of each edge reflected; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=along%40INTERNALPLANE2%3A%2B3V3%7CEXT_VDD_5V serves each with its own layer_image region; all of them lie in x 91.03..93.69, y 75.2..77.53 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:ETH100_AGND@MIDLAYER2:134.4,85.17'PB17' crosses where the outline of the ETH100_AGND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.08 mm (fastest: PB17 at 100 ps 10-90 %, ASSUMED)

      Along 'PB17' on MIDLAYER1, the ETH100_AGND plane on MIDLAYER2 has 0.08 mm under the track with no copper, at (134.4, 85.17), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 121.87..136.17, y 72.62..88.29 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'PB17' on MIDLAYER1 at (134.4, 85.17), 0.08 mm over no copper, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AETH100_AGND%40MIDLAYER2%3A134.4%2C85.17 serves each with its own layer_image region; all of them lie in x 133.37..135.44, y 84.17..86.17 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:ETH100_AGND@MIDLAYER2:134.49,87.2'PC2' crosses where the outline of the ETH100_AGND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.25 mm (fastest: PC2 at 100 ps 10-90 %, ASSUMED)

      Along 'PC2' on MIDLAYER1, the ETH100_AGND plane on MIDLAYER2 has 0.25 mm under the track with no copper, at (134.49, 87.2), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 121.87..136.17, y 72.62..88.29 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'PC2' on MIDLAYER1 at (134.49, 87.2), 0.25 mm over no copper, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3AETH100_AGND%40MIDLAYER2%3A134.49%2C87.2 serves each with its own layer_image region; all of them lie in x 133.37..135.62, y 86.2..88.2 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@MIDLAYER1|MIDLAYER25 nets on MIDLAYER1 cross the tracks routed through the ETH100_AGND pour on MIDLAYER2 at 5 places, the longest 18.61 mm; 4 run ALONG the cut round another net's track (fastest: PB13 at 100 ps 10-90 %, ASSUMED)

      The ETH100_AGND pour on MIDLAYER2 is cleared round tracks routed through it, and tracks on MIDLAYER1, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 5 place(s) on 5 net(s). 4 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 8.13 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'PB17' on MIDLAYER1 at (119.94, 85.17), 18.61 mm, running ALONG the bare copper for 7.94 mm, not across it over copper of NetIC4_19, NetIC4_20, not a plane, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2
      • 'PB15' on MIDLAYER1 at (120.9, 84.94), 18.1 mm, running ALONG the bare copper for 8.11 mm, not across it over copper of NetIC4_19, NetIC4_20, NetIC4_24, not a plane, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2
      • 'PB13' on MIDLAYER1 at (121.01, 84.71), 17.59 mm, running ALONG the bare copper for 8.13 mm, not across it over copper of NetIC4_19, NetIC4_20, NetIC4_24, NetIC4_28, not a plane, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2
      • 'PB18' on MIDLAYER1 at (121.15, 84.43), 15.12 mm, running ALONG the bare copper for 7.48 mm, not across it over copper of NetIC4_19, NetIC4_20, NetIC4_24, NetIC4_28, not a plane, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2
      • 'PC1' on MIDLAYER1 at (135.73, 85.75), 5.05 mm over copper of NRST, not a plane, to the end of the track; other side: GND on INTERNALPLANE1, 0.32 mm from the track against 0.32 mm to MIDLAYER2: 50% of the return on MIDLAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/10/reference-planes?group=void%3Arouted%40MIDLAYER1%7CMIDLAYER2 serves each with its own layer_image region; all of them lie in x 109.19..140.45, y 83.43..93.16 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

Main parts

Part numberMakerDescriptionWhere
AD1981BAC ’97 SoundMAX® CodecIC1
AT91SAM9263-CUAtmel ARM926 MCUIC5
CFPX-180 24.576 MHzMiniature crystal oscillator (ABRACON)X2
DM9161AEPDavicom 100Mbps ethernet PHYIC4
MEM_AT45DB642serial data FLASHIC10
microSD cardSecure Digital Cards socket (Farnell)CN1
SN74LVC1G66DCKRTI single analog switchIC9
SP2526USB power switchIC11
TR_H1260NLethernet trafo (TME)Tr1
XO53050UITA 50 MHzSMD oscillator 3.3V (Elfa)IC3
MT48LC16M16A2TGMicron 256Mbit PC133 SDRAM w/16-bit data busIC6, IC7
PBHTD60S1.27 mm dual row goldpin (Maritex)CN2, CN3
TPS62000DGSTI sync converterIC2, IC8
B32529C0104K000EPCOSNon-polarised capacitorC69
CC0402_1NF_50V_10%_X7RGENERICNon-polarised capacitorC59
CC0603_10NF_50V_10%_X7RGENERICNon-polarised capacitorC39
CC0603_10uF_6.3V_20%_X5RGENERICNon-polarised capacitorC22
CC0603_1NF_50V_10%_X7RGENERICNon-polarised capacitorC40
CC0603_4.7NF_50V_10%_X7RGENERICNon-polarised capacitorC37
CC0603_470PF_50V_5%_NP0GENERICNon-polarised capacitorC38
CTE3528-21_47UF_6.3V_10%_LESR0250GENERICPolarised capacitorC67
R0603_22K_1%_0.1W_100PPMGENERICResistor - 1%R31
R0603_2K_1%_0.1W_100PPMGENERICResistor - 1%R17
R0603_3K9_1%_0.1W_100PPMGENERICResistor - 1%R11
R0603_680K_1%_0.1W_100PPMGENERICResistor - 1%R26
R0603_6K8_1%_0.1W_100PPMGENERICResistor - 1%R51
R0805_0R_JUMPERGENERICResistor - 1%R10
R1206_0R_JUMPERGENERICResistor - 1%R117
RAC4X101 68kResistor network 1206 (4x0402) Maritex RAC4XxxxRP5
CC0603_33PF_50V_5%_NP0GENERICNon-polarised capacitorC66, C68
R0603_0R_JUMPERGENERICResistor - 1%R18, R22
R0603_1K5_1%_0.1W_100PPMGENERICResistor - 1%R15, R19
R0603_1K_1%_0.1W_100PPMGENERICResistor - 1%R1, R2
R0603_27R_1%_0.1W_100PPMGENERICResistor - 1%R32, R33
R0603_2K2_1%_0.1W_100PPMGENERICResistor - 1%R4, R5
R0603_47R_1%_0.1W_100PPMGENERICResistor - 1%R3, R34
R0603_75R_1%_0.1W_100PPMGENERICResistor - 1%R28, R29
CC0603_1uF_16V_10%_X7RGENERICNon-polarised capacitorC15, C16, C17
CC1206_10uF_10V_10%_X7RGENERICNon-polarised capacitorC63, C64, C82
CTE3528-21_100UF_6.3V_10%GENERICPolarised capacitorC1, C2, C21

About this design

Design
ARMADILLO — OHWR0007 R1
Designed in
Altium Designer
Board
6 copper layers, 64.5 × 43.7 mm, 178 components, 272 nets
Licence
MIT
Source
https://gitlab.com/ohwr/project/armadillo at commit 5afa855fbea7
Attribution
CERN Open Hardware Repository, project ohwr/project/armadillo (commit 5afa855fbea7759648476863b023cada73d2c9c1, 2025-04-09). Licence: MIT (the schematic title block says 'MIT-style'). Source: https://gitlab.com/ohwr/project/armadillo. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)