Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

ARRAY PROBE CARD

OHWR0003 · revision R1

ARRAY PROBE CARD (OHWR0003 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 8-layer board of 220 × 264 mm with 439 components and 291 nets, published under CERN-OHL-1.2.

review 96% walked · 3 findings: 2 major · 1 minor (50 items)

Open in the interactive viewerRead the full review

ARRAY PROBE CARD (OHWR0003 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 3 findings: 2 major · 1 minor (50 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 48 boards×48

    48 checked by the review by Claude walker W4 (Cern session) — 41 different reasons

    At merged:108.59,237.49|121.29,242.57, merged:128.91,237.49|141.61,242.57, merged:149.23,237.49|161.93,242.57, merged:202.93,165.28|214.19,165.28, merged:210.19,237.49|222.89,242.57, merged:230.51,234.95|243.21,242.57 and 42 more

    Each finding, with its own headline
    • merged:108.59,237.49|121.29,242.573 nets cross the slot of 14 drills from (108.59, 237.49) to (121.29, 242.57), whose anti-pads run together in the GND plane on BOTTOM_LAYER, the GND plane on L2 and the GND plane on L6, between 2 pairs of drills (fastest: NetB1_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on BOTTOM_LAYER, the GND plane on L2 and the GND plane on L6 are cleared round a field of 14 drills from (108.59, 237.49) to (121.29, 242.57), and the clearances run together: the straight line from one drill to the next is bare all the way. 3 nets cross between drills of it at 3 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetB1_1' on L7 at (119.38, 240.2), 8.19 mm between the drills at (116.21, 237.49) and (121.29, 237.49) in BOTTOM_LAYER; other side: no plane on L6
      • 'NetB1_1' on L7 at (119.38, 240.2), 8.19 mm between the drills at (116.21, 237.49) and (121.29, 237.49) in L6; other side: no plane on BOTTOM_LAYER
      • 'NetPP27_1' on L3 at (111.13, 236.2), 7.69 mm between the drills at (113.67, 237.49) and (108.59, 237.49) in L2; other side: no plane on L4
      • 'NetPP74_1' on L3 at (118.75, 236.2), 7.69 mm between the drills at (116.21, 237.49) and (121.29, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A108.59%2C237.49%7C121.29%2C242.57 serves each with its own layer_image region; all of them lie in x 107.59..122.29, y 232.64..245.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:128.91,237.49|141.61,242.572 nets cross the slot of 14 drills from (128.91, 237.49) to (141.61, 242.57), whose anti-pads run together in the GND plane on L2, between 2 pairs of drills (fastest: NetPP109_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L2 is cleared round a field of 14 drills from (128.91, 237.49) to (141.61, 242.57), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP109_1' on L3 at (131.45, 236.2), 7.69 mm between the drills at (133.99, 237.49) and (128.91, 237.49) in L2; other side: no plane on L4
      • 'NetPP76_1' on L3 at (139.07, 236.2), 7.69 mm between the drills at (136.53, 237.49) and (141.61, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A128.91%2C237.49%7C141.61%2C242.57 serves each with its own layer_image region; all of them lie in x 127.91..142.61, y 232.64..241.03 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:149.23,237.49|161.93,242.57'NetPP65_1' crosses between the drills at (154.31, 237.49) and (149.23, 237.49), whose anti-pads run together in the GND plane on L2 (fastest: NetPP65_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP65_1' on L3, the GND plane on L2 is cleared round the drills at (154.31, 237.49) and (149.23, 237.49), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 7.69 mm of bare stretch at (151.77, 236.2). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP65_1' on L3 at (151.77, 236.2), 7.69 mm between the drills at (154.31, 237.49) and (149.23, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A149.23%2C237.49%7C161.93%2C242.57 serves each with its own layer_image region; all of them lie in x 148.23..152.77, y 232.64..241.03 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:202.93,165.28|214.19,165.28'NetPP133_1' crosses between the drills at (208.56, 160.95) and (202.93, 165.28), whose anti-pads run together in the GND plane on L6 (fastest: NetPP133_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP133_1' on L7, the GND plane on L6 is cleared round the drills at (208.56, 160.95) and (202.93, 165.28), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 13.85 mm of bare stretch at (203.84, 160.66). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP133_1' on L7 at (203.84, 160.66), 13.85 mm between the drills at (208.56, 160.95) and (202.93, 165.28) in L6; other side: no plane on BOTTOM_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A202.93%2C165.28%7C214.19%2C165.28 serves each with its own layer_image region; all of them lie in x 202.84..206.74, y 153.81..168.08 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:210.19,237.49|222.89,242.57'NetPP104_1' crosses between the drills at (215.27, 237.49) and (210.19, 237.49), whose anti-pads run together in the GND plane on L2 (fastest: NetPP104_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP104_1' on L3, the GND plane on L2 is cleared round the drills at (215.27, 237.49) and (210.19, 237.49), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 7.69 mm of bare stretch at (212.73, 236.2). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP104_1' on L3 at (212.73, 236.2), 7.69 mm between the drills at (215.27, 237.49) and (210.19, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A210.19%2C237.49%7C222.89%2C242.57 serves each with its own layer_image region; all of them lie in x 209.19..213.73, y 232.64..241.03 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:230.51,234.95|243.21,242.57'NetPP118_1' crosses between the drills at (238.13, 237.49) and (243.21, 237.49), whose anti-pads run together in the GND plane on L2 (fastest: NetPP118_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP118_1' on L3, the GND plane on L2 is cleared round the drills at (238.13, 237.49) and (243.21, 237.49), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 7.69 mm of bare stretch at (240.67, 236.2). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP118_1' on L3 at (240.67, 236.2), 7.69 mm between the drills at (238.13, 237.49) and (243.21, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A230.51%2C234.95%7C243.21%2C242.57 serves each with its own layer_image region; all of them lie in x 239.67..244.21, y 232.64..241.03 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:250.83,234.95|263.53,242.57'NetPP62_1' crosses between the drills at (258.45, 237.49) and (263.53, 237.49), whose anti-pads run together in the GND plane on L2 (fastest: NetPP62_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP62_1' on L3, the GND plane on L2 is cleared round the drills at (258.45, 237.49) and (263.53, 237.49), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 7.69 mm of bare stretch at (260.99, 236.2). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP62_1' on L3 at (260.99, 236.2), 7.69 mm between the drills at (258.45, 237.49) and (263.53, 237.49) in L2; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=merged%3A250.83%2C234.95%7C263.53%2C242.57 serves each with its own layer_image region; all of them lie in x 259.99..264.53, y 232.64..241.03 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:149.86,175.03'NetPP87_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 1.68 mm (fastest: NetPP87_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP87_1' on L7, the GND plane on BOTTOM_LAYER has 1.68 mm under the track with no copper, at (149.86, 175.03), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP87_1' on L7 at (149.86, 175.03), 1.68 mm over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A149.86%2C175.03 serves each with its own layer_image region; all of them lie in x 148.86..150.86, y 173.19..176.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:149.86,192.73'NetPP87_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 26.23 mm (fastest: NetPP87_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP87_1' on L7, the GND plane on BOTTOM_LAYER has 26.23 mm under the track with no copper, at (149.86, 192.73), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 22.3 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP87_1' on L7 at (149.86, 192.73), 26.23 mm, running ALONG the bare copper for 22.3 mm, not across it over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A149.86%2C192.73 serves each with its own layer_image region; all of them lie in x 147.82..150.86, y 179.35..207.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:167.01,255.27'NetPP4_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 5.05 mm (fastest: NetPP4_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP4_1' on L7, the GND plane on BOTTOM_LAYER has 5.05 mm under the track with no copper, at (167.01, 255.27), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP4_1' on L7 at (167.01, 255.27), 5.05 mm over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A167.01%2C255.27 serves each with its own layer_image region; all of them lie in x 166.01..168.01, y 251.74..258.8 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:216.54,117.63'NetPP133_1' crosses one void in the GND plane on BOTTOM_LAYER and the GND plane on L6 at 1 place, the longest 18.93 mm; 1 cleared on both sides of the track (fastest: NetPP133_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP133_1' on L7, the GND plane on L6 has 18.93 mm under the track with no copper, at (216.54, 116.66), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 14.58 mm). What cleared it: the hole at x 200.35..266.03, y 95.56..258.87. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 2 reference layers: 'NetPP133_1' on L7 at (216.54, 117.63), 2.11 mm over no copper; other side: no plane on L6 / 'NetPP133_1' on L7 at (216.54, 116.66), 18.93 mm, running ALONG the bare copper for 14.58 mm, not across it over no copper; other side: no plane on BOTTOM_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A216.54%2C117.63 serves each with its own layer_image region; all of them lie in x 214.09..217.54, y 107.22..127.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:228.6,127.37'NetPP106_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 1.55 mm (fastest: NetPP106_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP106_1' on L7, the GND plane on BOTTOM_LAYER has 1.55 mm under the track with no copper, at (228.6, 127.37), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP106_1' on L7 at (228.6, 127.37), 1.55 mm over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A228.6%2C127.37 serves each with its own layer_image region; all of them lie in x 227.6..229.6, y 125.6..129.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:228.6,146.86'NetPP106_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 1.55 mm (fastest: NetPP106_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP106_1' on L7, the GND plane on BOTTOM_LAYER has 1.55 mm under the track with no copper, at (228.6, 146.86), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP106_1' on L7 at (228.6, 146.86), 1.55 mm over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A228.6%2C146.86 serves each with its own layer_image region; all of them lie in x 227.6..229.6, y 145.09..148.64 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:228.6,155.54'NetPP106_1' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 1.55 mm (fastest: NetPP106_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP106_1' on L7, the GND plane on BOTTOM_LAYER has 1.55 mm under the track with no copper, at (228.6, 155.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP106_1' on L7 at (228.6, 155.54), 1.55 mm over no copper; other side: no plane on L6

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A228.6%2C155.54 serves each with its own layer_image region; all of them lie in x 227.6..229.6, y 153.77..157.31 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@BOTTOM_LAYER:228.6,175.0320 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L2, the GND plane on L3, the GND plane on L4, the GND plane on L5, the GND plane on L6, the GND plane on L7 and the GND plane on TOP_LAYER at 1 place, the longest 123.99 mm; 58 over tracks of other nets routed inside it (fastest: NetPP105_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP106_1' on L7, the GND plane on L6 has 123.99 mm under the track with copper of NetPP83_1, NetPP71_1, NetPP117_1, not a plane, at (240.67, 220.62), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 58 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 50 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 95.18 mm). What cleared it: the hole at x 106.08..266.03, y 95.56..271.57 and the hole at x 126.4..245.71, y 85.81..271.57 and the hole at x 200.35..266.03, y 95.56..258.87. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 14 of the 66 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 66 reference layers: 'NetPP105_1' on L4 at (217.17, 181.35), 5.89 mm over copper of NetPP35_1, not a plane; other side: no plane on L5 / 'NetPP105_1' on L4 at (217.17, 182.52), 53.52 mm, running ALONG the bare copper for 47.78 mm, not across it over copper of NetPP94_1, not a plane; other side: no plane on L3 / 'NetPP106_1' on L7 at (228.6, 175.03), 1.55 mm over no copper; other side: no plane on L6 / 'NetPP106_1' on L7 at (240.67, 222.21), 76.57 mm, running ALONG the bare copper for 68.48 mm, not across it over copper of NetPP128_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP106_1' on L7 at (240.67, 220.62), 123.99 mm, running ALONG the bare copper for 95.18 mm, not across it over copper of NetPP83_1, NetPP71_1, NetPP117_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP107_1' on L5 at (228.6, 159.7), 48.44 mm, running ALONG the bare copper for 43.14 mm, not across it over copper of NetPP95_1, not a plane; other side: no plane on L6 / 'NetPP107_1' on L5 at (228.6, 172.05), 65.98 mm, running ALONG the bare copper for 38.21 mm, not across it over copper of NetPP71_1, NetPP117_1, NetPP83_1, not a plane; other side: no plane on L4 / 'NetPP117_1' on L6 at (217.17, 136.48), 18.75 mm, running ALONG the bare copper for 12.87 mm, not across it over copper of NetPP94_1, not a plane; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP117_1' on L6 at (227.97, 213.36), 13.08 mm, running ALONG the bare copper for 7.48 mm, not across it over copper of NetPP60_1, not a plane; other side: no plane on L7 / 'NetPP117_1' on L6 at (228.6, 172.05), 39.94 mm, running ALONG the bare copper for 26.83 mm, not across it over copper of NetPP60_1, NetPP107_1, not a plane; other side: no plane on L7 / 'NetPP117_1' on L6 at (230.51, 218.18), 5.89 mm over copper of NetPP94_1, not a plane; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP117_1' on L6 at (223.61, 158.2), 3.86 mm over no copper; other side: no plane on L5 / 'NetPP117_1' on L6 at (227.97, 213.36), 13.08 mm, running ALONG the bare copper for 7.44 mm, not across it over copper of NetPP48_1, not a plane; other side: no plane on L5 / 'NetPP117_1' on L6 at (228.6, 171.73), 23.04 mm, running ALONG the bare copper for 17.3 mm, not across it over copper of NetPP106_1, not a plane; other side: no plane on L5 / 'NetPP118_1' on L3 at (240.67, 198.47), 5.89 mm over copper of NetPP15_1, not a plane; other side: no plane on L4 / 'NetPP118_1' on L3 at (228.6, 155.44), 57.32 mm, running ALONG the bare copper for 51.74 mm, not across it over copper of NetPP95_1, not a plane; other side: no plane on L2 / 'NetPP118_1' on L3 at (240.67, 217.45), 48.06 mm, running ALONG the bare copper for 43.05 mm, not across it over copper of NetPP95_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP128_1' on BOTTOM_LAYER at (240.67, 222.21), 76.99 mm, running ALONG the bare copper for 68.65 mm, not across it over copper of NetPP106_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP14_1' on L2 at (214.19, 194.61), 5.73 mm, running ALONG the bare copper for 3.47 mm, not across it over no copper; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP14_1' on L2 at (233.05, 226.06), 36.61 mm, running ALONG the bare copper for 31.6 mm, not across it over copper of NetPP35_1, not a plane, to the end of the track; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP14_1' on L2 at (219.69, 202.55), 17.54 mm, running ALONG the bare copper for 13.14 mm, not across it over no copper; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP14_1' on L2 at (233.05, 233.06), 5.94 mm, running ALONG the bare copper for 2.88 mm, not across it over copper of PP117, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP15_1' on L2 at (239.59, 198.92), 5.89 mm over copper of NetPP118_1, not a plane; other side: no plane on TOP_LAYER / 'NetPP15_1' on L2 at (243.21, 218.71), 41.31 mm, running ALONG the bare copper for 32.61 mm, not across it over copper of NetPP36_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP35_1' on L3 at (233.05, 226.1), 39.15 mm, running ALONG the bare copper for 32.22 mm, not across it over copper of NetPP14_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP35_1' on L3 at (216.09, 181.8), 5.89 mm over copper of NetPP105_1, not a plane; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP35_1' on L3 at (221.81, 187.52), 5.89 mm over copper of NetPP59_1, not a plane; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP35_1' on L3 at (233.05, 227.33), 39.15 mm, running ALONG the bare copper for 34.53 mm, not across it over copper of NetPP59_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP36_1' on TOP_LAYER at (241.94, 218.08), 39.07 mm, running ALONG the bare copper for 33.05 mm, not across it over copper of NetPP15_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP47_1' on L6 at (217.17, 183.79), 58.45 mm, running ALONG the bare copper for 49.02 mm, not across it over copper of NetPP94_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP59_1' on L4 at (222.89, 165.28), 0.78 mm over no copper; other side: no plane on L5 / 'NetPP59_1' on L4 at (222.89, 184.77), 0.78 mm over no copper; other side: no plane on L5 / 'NetPP59_1' on L4 at (222.89, 186.97), 6.08 mm over copper of NetPP35_1, not a plane; other side: no plane on L5 / 'NetPP59_1' on L4 at (233.05, 227.37), 41.69 mm, running ALONG the bare copper for 34.37 mm, not across it over copper of NetPP35_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP59_1' on L4 at (222.89, 180.08), 71.51 mm, running ALONG the bare copper for 65.61 mm, not across it over copper of NetPP60_1, not a plane; other side: GND on L3, 0.2 mm from the track against 0.7 mm to L5: 22% of the return on L5 / 'NetPP59_1' on L4 at (233.05, 231.74), 24.56 mm, running ALONG the bare copper for 18.95 mm, not across it over copper of NetPP94_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP60_1' on L5 at (222.89, 180.04), 71.51 mm, running ALONG the bare copper for 65.53 mm, not across it over copper of NetPP59_1, not a plane; other side: no plane on L6 / 'NetPP60_1' on L5 at (240.67, 232.37), 27.63 mm, running ALONG the bare copper for 18.08 mm, not across it over copper of NetPP95_1, GND, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP60_1' on L5 at (222.89, 175.89), 77.74 mm, running ALONG the bare copper for 56.92 mm, not across it over copper of NetPP117_1, NetPP82_1, NetPP71_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP60_1' on L5 at (240.67, 234.32), 27.63 mm, running ALONG the bare copper for 21.89 mm, not across it over copper of NetPP83_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP71_1' on L6 at (233.05, 217.43), 5.03 mm over copper of NetPP60_1, not a plane; other side: no plane on L7 / 'NetPP71_1' on L6 at (233.05, 233.68), 32.18 mm, running ALONG the bare copper for 23.13 mm, not across it over copper of NetPP94_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP71_1' on L6 at (234.32, 172.03), 54.6 mm, running ALONG the bare copper for 34.48 mm, not across it over copper of NetPP107_1, NetPP84_1, not a plane; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP71_1' on L6 at (228.6, 151.16), 18.53 mm, running ALONG the bare copper for 12.94 mm, not across it over copper of NetPP106_1, not a plane; other side: no plane on L5 / 'NetPP71_1' on L6 at (233.05, 232.41), 37.67 mm, running ALONG the bare copper for 33.62 mm, not across it over copper of NetPP48_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP71_1' on L6 at (235.9, 189.55), 10.38 mm, running ALONG the bare copper for 4.49 mm, not across it over copper of NetPP106_1, not a plane; other side: no plane on L5 / 'NetPP71_1' on L6 at (237.49, 199.92), 4.15 mm over no copper; other side: no plane on L5 / 'NetPP72_1' on L4 at (232.33, 150.42), 8.36 mm over copper of NetPP84_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.7 mm to L5: 22% of the return on L5 / 'NetPP82_1' on L6 at (222.89, 175.9), 55.78 mm, running ALONG the bare copper for 41.42 mm, not across it over copper of NetPP94_1, NetPP60_1, not a plane; other side: no plane on L7 / 'NetPP82_1' on L6 at (223.52, 214), 11.28 mm, running ALONG the bare copper for 5.39 mm, not across it over copper of NetPP94_1, not a plane; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP82_1' on L6 at (222.89, 175.9), 65.86 mm, running ALONG the bare copper for 52.33 mm, not across it over copper of NetPP70_1, NetPP48_1, not a plane; other side: no plane on L5 / 'NetPP83_1' on L6 at (234.32, 149.86), 27.71 mm, running ALONG the bare copper for 15.24 mm, not across it over copper of NetPP107_1, NetPP84_1, not a plane, to the end of the track; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP83_1' on L6 at (240.67, 191.4), 13.4 mm over copper of NetPP84_1, NetPP107_1, not a plane; other side: no plane on L7 / 'NetPP83_1' on L6 at (240.67, 234.24), 30.91 mm, running ALONG the bare copper for 21.94 mm, not across it over copper of NetPP60_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP83_1' on L6 at (227.27, 137.12), 5.29 mm over copper of NetPP106_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP83_1' on L6 at (240.67, 220.62), 63.82 mm, running ALONG the bare copper for 58.82 mm, not across it over copper of NetPP106_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP84_1' on L5 at (233.68, 153.33), 5.97 mm, running ALONG the bare copper for 3.21 mm, not across it over copper of NetPP72_1, not a plane; other side: no plane on L6 / 'NetPP84_1' on L5 at (233.68, 152.08), 53.97 mm, running ALONG the bare copper for 35.79 mm, not across it over copper of NetPP83_1, NetPP71_1, not a plane; other side: no plane on L4 / 'NetPP94_1' on L5 at (217.17, 182.52), 63.49 mm, running ALONG the bare copper for 54.42 mm, not across it over copper of NetPP59_1, NetPP105_1, not a plane; other side: no plane on L6 / 'NetPP94_1' on L5 at (233.05, 231.81), 28.9 mm, running ALONG the bare copper for 19.25 mm, not across it over copper of NetPP59_1, GND, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP94_1' on L5 at (217.17, 183.79), 94.14 mm, running ALONG the bare copper for 78.16 mm, not across it over copper of NetPP117_1, NetPP82_1, NetPP47_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP94_1' on L5 at (233.05, 233.68), 32.49 mm, running ALONG the bare copper for 23.31 mm, not across it over copper of NetPP117_1, NetPP71_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP95_1' on L4 at (228.6, 155.37), 56.99 mm, running ALONG the bare copper for 51.14 mm, not across it over copper of NetPP118_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP95_1' on L4 at (240.67, 217.45), 50.6 mm, running ALONG the bare copper for 44.07 mm, not across it over copper of NetPP118_1, not a plane, to the end of the track; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP95_1' on L4 at (228.6, 159.7), 48.44 mm, running ALONG the bare copper for 42.56 mm, not across it over copper of NetPP107_1, not a plane; other side: no plane on L3 / 'NetPP95_1' on L4 at (240.67, 232.37), 23.29 mm, running ALONG the bare copper for 17.69 mm, not across it over copper of NetPP60_1, not a plane, to the end of the track; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A228.6%2C175.03 serves each with its own layer_image region; all of them lie in x 207.56..245.48, y 125.6..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2:hole 106.08,145.91|134.8,246.1714 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L2, the GND plane on L3, the GND plane on L4, the GND plane on L5, the GND plane on L6, the GND plane on L7 and the GND plane on TOP_LAYER at 4 places, the longest 109.06 mm; 27 over tracks of other nets routed inside it (fastest: NetPP109_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP97_1' on L4, the GND plane on L3 has 109.06 mm under the track with copper of NetPP109_1, NetPP74_1, not a plane, at (132.72, 158.36), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 27 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 20 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 94 mm). 4 places on 14 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 106.08..134.8, y 145.91..246.17 and the hole at x 106.08..266.03, y 95.56..271.57 and the hole at x 126.27..171.76, y 95.56..258.87 and the hole at x 126.4..245.71, y 85.81..271.57. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 27 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: 'NetPP109_1' on L3 at (131.45, 200.61), 60.65 mm, running ALONG the bare copper for 52.6 mm, not across it over copper of NetPP97_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP17_1' on BOTTOM_LAYER at (131.45, 218.08), 74.88 mm, running ALONG the bare copper for 67.66 mm, not across it over copper of NetPP41_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP28_1' on L2 at (135.42, 170.79), 22.03 mm, running ALONG the bare copper for 18.98 mm, not across it over copper of NetPP74_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP28_1' on L2 at (135.42, 170.79), 18.77 mm, running ALONG the bare copper for 9.87 mm, not across it over copper of NetPP52_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP41_1' on L7 at (131.45, 218.08), 85.25 mm, running ALONG the bare copper for 78.19 mm, not across it over copper of NetPP17_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP41_1' on L7 at (131.45, 197.75), 79.06 mm, running ALONG the bare copper for 68.71 mm, not across it over copper of NetPP98_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP51_1' on L2 at (132.72, 155.87), 14.86 mm, running ALONG the bare copper for 7.03 mm, not across it over copper of NetPP74_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP51_1' on L2 at (132.72, 155.87), 16.98 mm, running ALONG the bare copper for 7.17 mm, not across it over copper of NetPP52_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP52_1' on TOP_LAYER at (132.72, 155.87), 12.92 mm, running ALONG the bare copper for 6.86 mm, not across it over copper of NetPP51_1, not a plane; other side: none: the signal layer is outermost / 'NetPP52_1' on TOP_LAYER at (132.72, 179.96), 5.89 mm over copper of NetPP28_1, not a plane; other side: none: the signal layer is outermost / 'NetPP74_1' on L3 at (130.78, 180.37), 11.28 mm, running ALONG the bare copper for 5.44 mm, not across it over copper of NetPP28_1, not a plane; other side: no plane on L4 / 'NetPP74_1' on L3 at (132.72, 155.87), 12.92 mm, running ALONG the bare copper for 6.86 mm, not across it over copper of NetPP51_1, not a plane; other side: no plane on L4 / 'NetPP74_1' on L3 at (126.81, 184.34), 5.89 mm over copper of NetPP86_1, not a plane; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP74_1' on L3 at (132.72, 158.36), 47.99 mm, running ALONG the bare copper for 40.16 mm, not across it over copper of NetPP97_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP75_1' on L5 at (131.45, 197.75), 73.24 mm, running ALONG the bare copper for 60.46 mm, not across it over copper of GND, NetPP97_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP75_1' on L5 at (131.45, 197.75), 73.24 mm, running ALONG the bare copper for 64.37 mm, not across it over copper of NetPP98_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP86_1' on L4 at (125.73, 186.95), 5.89 mm over copper of NetPP74_1, not a plane; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP97_1' on L4 at (132.72, 158.36), 109.06 mm, running ALONG the bare copper for 94 mm, not across it over copper of NetPP109_1, NetPP74_1, not a plane, to the end of the track; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP97_1' on L4 at (132.72, 196.59), 68.9 mm, running ALONG the bare copper for 60.26 mm, not across it over copper of NetPP75_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP98_1' on L6 at (132.72, 196.59), 76.52 mm, running ALONG the bare copper for 64.41 mm, not across it over copper of NetPP75_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP98_1' on L6 at (132.72, 196.59), 76.52 mm, running ALONG the bare copper for 68.48 mm, not across it over copper of NetPP41_1, not a plane, to the end of the track; other side: no plane on L5
      • one crossing of two tracks, seen from each: 'NetPP40_1' on L2 at (108.59, 198.08), 82.76 mm, running ALONG the bare copper for 74.62 mm, not across it over copper of NetPP63_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP63_1' on TOP_LAYER at (109.86, 197.46), 80.3 mm, running ALONG the bare copper for 73.73 mm, not across it over copper of NetPP40_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP27_1' on L3 at (120.21, 176.63), 5.89 mm over copper of NetPP51_1, not a plane; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2 / 'NetPP51_1' on L2 at (121.29, 177.08), 5.89 mm over copper of NetPP27_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3
      • one crossing of two tracks, seen from each: 'NetPP51_1' on L2 at (121.29, 191.39), 5.89 mm over copper of NetPP74_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP74_1' on L3 at (120.21, 190.94), 5.89 mm over copper of NetPP51_1, not a plane; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L2%3Ahole%20106.08%2C145.91%7C134.8%2C246.17 serves each with its own layer_image region; all of them lie in x 106.33..140.17, y 133.42..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2:hole 126.4,85.81|245.71,271.5746 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L2, the GND plane on L3, the GND plane on L4, the GND plane on L5, the GND plane on L6, the GND plane on L7 and the GND plane on TOP_LAYER at 12 places, the longest 142.52 mm; 91 over tracks of other nets routed inside it (fastest: NetPP100_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP91_1' on L3, the GND plane on L4 has 142.52 mm under the track with copper of NetPP90_1, NetPP11_1, not a plane, at (184.79, 233.36), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 91 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 85 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 122.79 mm). 12 places on 46 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 106.08..266.03, y 95.56..271.57 and the hole at x 126.27..171.76, y 95.56..258.87 and the hole at x 126.4..245.71, y 85.81..271.57. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 18 of the 97 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 52 reference layers: 'NetPP100_1' on L6 at (154.94, 170.7), 87.16 mm, running ALONG the bare copper for 81.34 mm, not across it over copper of NetPP88_1, not a plane; other side: no plane on L7 / 'NetPP100_1' on L6 at (159.39, 230.51), 37.67 mm, running ALONG the bare copper for 29.66 mm, not across it over copper of NetPP122_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP100_1' on L6 at (154.94, 180.16), 68.4 mm, running ALONG the bare copper for 62.68 mm, not across it over copper of NetPP54_1, not a plane; other side: no plane on L5 / 'NetPP100_1' on L6 at (159.39, 232.45), 37.67 mm, running ALONG the bare copper for 33.62 mm, not across it over copper of NetPP77_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP101_1' on BOTTOM_LAYER at (172.09, 165.42), 20.52 mm, running ALONG the bare copper for 17.86 mm, not across it over copper of NetPP77_1, not a plane; other side: none: the signal layer is outermost / 'NetPP102_1' on L3 at (177.8, 179.74), 100.48 mm, running ALONG the bare copper for 80.27 mm, not across it over copper of NetPP124_1, NetPP79_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP102_1' on L3 at (177.8, 188.87), 113.62 mm, running ALONG the bare copper for 94.99 mm, not across it over copper of NetPP89_1, NetPP90_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP111_1' on L6 at (151.77, 230.58), 37.67 mm, running ALONG the bare copper for 29.56 mm, not across it over copper of NetPP88_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP111_1' on L6 at (151.77, 232.45), 37.67 mm, running ALONG the bare copper for 33.62 mm, not across it over copper of NetPP54_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP112_1' on L2 at (154.94, 148.68), 35.64 mm, running ALONG the bare copper for 20.12 mm, not across it over copper of NetPP65_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP112_1' on L2 at (167.01, 236.86), 89.49 mm, running ALONG the bare copper for 83.9 mm, not across it over copper of NetPP44_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP112_1' on L2 at (166.37, 192.72), 109.78 mm, running ALONG the bare copper for 71 mm, not across it over copper of NetPP43_1, GND, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP121_1' on L4 at (151.77, 227.72), 29.79 mm, running ALONG the bare copper for 23.06 mm, not across it over copper of NetPP65_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP121_1' on L4 at (151.77, 228.64), 30.24 mm, running ALONG the bare copper for 25.41 mm, not across it over copper of NetPP88_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP122_1' on L5 at (172.09, 154.28), 120.5 mm, running ALONG the bare copper for 100.02 mm, not across it over copper of NetPP66_1, GND, NetPP19_1, NetPP89_1, not a plane, to the end of the track; other side: GND on L6, 0.2 mm from the track against 0.7 mm to L4: 22% of the return on L4 / 'NetPP122_1' on L5 at (159.39, 230.51), 34.39 mm, running ALONG the bare copper for 29.51 mm, not across it over copper of NetPP100_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP122_1' on L5 at (166.37, 199.5), 20.87 mm, running ALONG the bare copper for 16.53 mm, not across it over no copper; other side: no plane on L4 / 'NetPP124_1' on L2 at (177.8, 179.74), 68.12 mm, running ALONG the bare copper for 51.66 mm, not across it over copper of NetPP102_1, NetPP91_1, NetPP78_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP124_1' on L2 at (179.71, 227.29), 50.64 mm, running ALONG the bare copper for 37.88 mm, not across it over copper of NetPP102_1, not a plane, to the end of the track; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP124_1' on L2 at (174.63, 204.79), 15.02 mm, running ALONG the bare copper for 12.07 mm, not across it over no copper; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP124_1' on L2 at (179.71, 245.11), 29.23 mm, running ALONG the bare copper for 11.33 mm, not across it over copper of PP1, PP79, PP102, PP90, PP67, PP56, PP130, PP113, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP19_1' on L4 at (167.01, 199.39), 30.55 mm, running ALONG the bare copper for 22.99 mm, not across it over copper of NetPP44_1, not a plane; other side: no plane on L5 / 'NetPP19_1' on L4 at (167.01, 199.39), 34.29 mm, running ALONG the bare copper for 28.72 mm, not across it over copper of NetPP122_1, not a plane; other side: no plane on L3 / 'NetPP30_1' on BOTTOM_LAYER at (152.4, 234.37), 44.51 mm, running ALONG the bare copper for 37.35 mm, not across it over copper of NetPP54_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP43_1' on TOP_LAYER at (158.48, 157.75), 10.82 mm over copper of NetPP112_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP44_1' on L3 at (167.01, 236.89), 108.4 mm, running ALONG the bare copper for 94.3 mm, not across it over copper of NetPP112_1, NetPP55_1, not a plane, to the end of the track; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2 / 'NetPP44_1' on L3 at (166.37, 199.39), 61.78 mm, running ALONG the bare copper for 46.23 mm, not across it over copper of NetPP19_1, NetPP89_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP54_1' on L7 at (151.77, 233.68), 92.03 mm, running ALONG the bare copper for 81.07 mm, not across it over copper of NetPP30_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP54_1' on L7 at (151.77, 232.45), 40.21 mm, running ALONG the bare copper for 33.85 mm, not across it over copper of NetPP111_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP54_1' on L7 at (154.94, 180.08), 68.78 mm, running ALONG the bare copper for 62.68 mm, not across it over copper of NetPP100_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP55_1' on L2 at (172.09, 203.87), 82.73 mm, running ALONG the bare copper for 73.73 mm, not across it over copper of NetPP78_1, NetPP44_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP55_1' on L2 at (172.09, 191.41), 74.92 mm, running ALONG the bare copper for 67.2 mm, not across it over copper of PP31, NetPP31_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP65_1' on L3 at (154.94, 148.68), 26.17 mm, running ALONG the bare copper for 20.07 mm, not across it over copper of NetPP112_1, not a plane, to the end of the track; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2 / 'NetPP65_1' on L3 at (151.77, 227.65), 27.56 mm, running ALONG the bare copper for 22.83 mm, not across it over copper of NetPP121_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP65_1' on L3 at (154.94, 183.46), 61.57 mm, running ALONG the bare copper for 57.33 mm, not across it over copper of NetPP66_1, not a plane; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP66_1' on L4 at (154.94, 183.47), 61.85 mm, running ALONG the bare copper for 55.98 mm, not across it over copper of NetPP65_1, not a plane; other side: no plane on L5 / 'NetPP66_1' on L4 at (154.94, 183.47), 61.7 mm, running ALONG the bare copper for 55.98 mm, not across it over copper of NetPP88_1, not a plane; other side: no plane on L3 / 'NetPP77_1' on L7 at (159.39, 233.68), 125.12 mm, running ALONG the bare copper for 103.15 mm, not across it over copper of NetPP9_1, NetPP101_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP77_1' on L7 at (159.39, 232.37), 40.33 mm, running ALONG the bare copper for 33.95 mm, not across it over copper of NetPP100_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP78_1' on L3 at (172.09, 203.87), 96.14 mm, running ALONG the bare copper for 80.56 mm, not across it over copper of NetPP124_1, NetPP55_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP78_1' on L3 at (172.09, 205.74), 104.23 mm, running ALONG the bare copper for 83.15 mm, not across it over copper of NetPP89_1, NetPP90_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP88_1' on L5 at (151.77, 228.64), 34.78 mm, running ALONG the bare copper for 25.6 mm, not across it over copper of GND, NetPP121_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP88_1' on L5 at (154.94, 183.47), 61.38 mm, running ALONG the bare copper for 57.33 mm, not across it over copper of NetPP66_1, not a plane; other side: no plane on L6 / 'NetPP88_1' on L5 at (151.77, 230.51), 34.39 mm, running ALONG the bare copper for 29.51 mm, not across it over copper of NetPP111_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP88_1' on L5 at (154.94, 170.7), 87.05 mm, running ALONG the bare copper for 81.45 mm, not across it over copper of NetPP100_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP89_1' on L4 at (172.09, 138.4), 14.76 mm, running ALONG the bare copper for 5.96 mm, not across it over copper of NetPP102_1, NetPP78_1, not a plane; other side: no plane on L5 / 'NetPP89_1' on L4 at (172.09, 205.82), 88.56 mm, running ALONG the bare copper for 78.82 mm, not across it over copper of NetPP44_1, NetPP78_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP89_1' on L4 at (172.09, 214.45), 110.9 mm, running ALONG the bare copper for 103.9 mm, not across it over copper of NetPP122_1, NetPP10_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP90_1' on L4 at (177.8, 188.91), 114.25 mm, running ALONG the bare copper for 97.16 mm, not across it over copper of NetPP91_1, NetPP102_1, NetPP78_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP90_1' on L4 at (177.8, 176.44), 108.55 mm, running ALONG the bare copper for 102.95 mm, not across it over copper of NetPP67_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP91_1' on L3 at (183.52, 166.05), 88.36 mm, running ALONG the bare copper for 62.41 mm, not across it over copper of NetPP124_1, NetPP79_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP91_1' on L3 at (184.79, 233.36), 142.52 mm, running ALONG the bare copper for 122.79 mm, not across it over copper of NetPP90_1, NetPP11_1, not a plane, to the end of the track; other side: no plane on L2
      • one crossing of two tracks, seen from each: 'NetPP103_1' on L4 at (194.31, 145.1), 92.25 mm, running ALONG the bare copper for 86.17 mm, not across it over copper of NetPP115_1, NetPP22_1, not a plane; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP103_1' on L4 at (194.31, 188.97), 54.15 mm, running ALONG the bare copper for 43.54 mm, not across it over copper of NetPP57_1, NetPP33_1, not a plane; other side: no plane on L3 / 'NetPP115_1' on L3 at (194.31, 145.1), 50.23 mm, running ALONG the bare copper for 42.55 mm, not across it over copper of NetPP125_1, not a plane; other side: no plane on L4 / 'NetPP115_1' on L3 at (194.31, 145.1), 124.92 mm, running ALONG the bare copper for 111.92 mm, not across it over copper of NetPP103_1, NetPP92_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP125_1' on L2 at (194.95, 145.1), 94.42 mm, running ALONG the bare copper for 83.74 mm, not across it over copper of NetPP22_1, NetPP115_1, not a plane; other side: no plane on TOP_LAYER / 'NetPP125_1' on L2 at (194.95, 161.6), 93.44 mm, running ALONG the bare copper for 71.82 mm, not across it over copper of 3.3V, VSS, NetPP69_1, NetPP21_1, not a plane; other side: no plane on L3 / 'NetPP22_1' on L3 at (194.31, 188.65), 39.25 mm, running ALONG the bare copper for 29.03 mm, not across it over copper of NetPP5_1, NetPP125_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP45_1' on L3 at (188.6, 172.7), 54.13 mm, running ALONG the bare copper for 41.89 mm, not across it over copper of NetPP5_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP5_1' on L2 at (194.31, 203.84), 21.52 mm, running ALONG the bare copper for 10.55 mm, not across it over copper of NetPP22_1, NetPP45_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP69_1' on TOP_LAYER at (194.31, 161.6), 52.61 mm, running ALONG the bare copper for 45.4 mm, not across it over copper of NetPP125_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP92_1' on L4 at (200.03, 151.04), 116.96 mm, running ALONG the bare copper for 106.62 mm, not across it over copper of NetPP115_1, not a plane, to the end of the track; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP92_1' on L4 at (200.03, 189.15), 104.14 mm, running ALONG the bare copper for 99.13 mm, not across it over copper of NetPP57_1, not a plane, to the end of the track; other side: no plane on L3
      • one stretch, cleared on 13 reference layers: 'NetPP104_1' on L3 at (200.66, 153.25), 77.78 mm, running ALONG the bare copper for 59.91 mm, not across it over copper of NetPP81_1, NetPP127_1, not a plane; other side: no plane on L4 / 'NetPP104_1' on L3 at (200.66, 148.59), 74.48 mm, running ALONG the bare copper for 59.09 mm, not across it over copper of NetPP126_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP104_1' on L3 at (212.73, 227.29), 28.37 mm, running ALONG the bare copper for 23.36 mm, not across it over copper of NetPP126_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP126_1' on L4 at (201.85, 125.65), 5.68 mm over copper of NetPP104_1, not a plane; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3 / 'NetPP126_1' on L4 at (203.2, 159.38), 11.29 mm over no copper; other side: no plane on L5 / 'NetPP126_1' on L4 at (205.74, 179.31), 20.5 mm, running ALONG the bare copper for 14.96 mm, not across it over copper of NetPP104_1, not a plane; other side: no plane on L5 / 'NetPP126_1' on L4 at (212.73, 227.37), 30.91 mm, running ALONG the bare copper for 23.69 mm, not across it over copper of NetPP104_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP126_1' on L4 at (205.74, 188.43), 90.97 mm, running ALONG the bare copper for 83.85 mm, not across it over copper of NetPP34_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP127_1' on L2 at (211.46, 198.49), 19.75 mm, running ALONG the bare copper for 10.73 mm, not across it over copper of NetPP104_1, not a plane; other side: no plane on TOP_LAYER / 'NetPP127_1' on L2 at (211.46, 200), 10.14 mm, running ALONG the bare copper for 4.64 mm, not across it over copper of NetPP7_1, not a plane; other side: no plane on L3 / 'NetPP7_1' on TOP_LAYER at (210.17, 196.13), 6.57 mm over copper of NetPP127_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP81_1' on L2 at (200.03, 153.83), 55.51 mm, running ALONG the bare copper for 47.97 mm, not across it over copper of NetPP104_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP81_1' on L2 at (205.74, 193.32), 97.57 mm, running ALONG the bare copper for 88.7 mm, not across it over copper of NetPP58_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER
      • one stretch, cleared on 5 reference layers: 'NetPP42_1' on L2 at (149.23, 182.12), 53.85 mm, running ALONG the bare copper for 46.39 mm, not across it over copper of NetPP76_1, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP42_1' on L2 at (149.23, 165.28), 5.03 mm over no copper; other side: no plane on L3 / 'NetPP42_1' on L2 at (149.23, 203.95), 63.96 mm, running ALONG the bare copper for 62.12 mm, not across it over copper of NetPP18_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP76_1' on L3 at (149.86, 181.59), 64.92 mm, running ALONG the bare copper for 53.84 mm, not across it over copper of NetPP8_1, NetPP42_1, not a plane; other side: no plane on L4 / 'NetPP8_1' on L2 at (144.14, 213.37), 13.06 mm, running ALONG the bare copper for 7.43 mm, not across it over copper of NetPP76_1, not a plane; other side: no plane on TOP_LAYER
      • 'NetPP29_1' on TOP_LAYER at (146.69, 201.34), 50.09 mm, running ALONG the bare copper for 45.25 mm, not across it over copper of NetPP8_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'NetPP22_1' on L3 at (200.03, 251.46), 30.55 mm, running ALONG the bare copper for 8.46 mm, not across it over copper of GND, not a plane, to the end of the track; other side: no plane on L4
      • one crossing of two tracks, seen from each: 'NetPP127_1' on L2 at (222.89, 225.39), 27.95 mm, running ALONG the bare copper for 19.25 mm, not across it over copper of NetPP7_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP7_1' on TOP_LAYER at (221.62, 224.76), 25.69 mm, running ALONG the bare copper for 19.69 mm, not across it over copper of NetPP127_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP1_1' on TOP_LAYER at (183.52, 225.38), 24.36 mm, running ALONG the bare copper for 18.94 mm, not across it over copper of NetPP79_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP79_1' on L2 at (183.52, 225.17), 26.68 mm, running ALONG the bare copper for 19.56 mm, not across it over copper of NetPP1_1, not a plane, to the end of the track; other side: no plane on L3
      • one crossing of two tracks, seen from each: 'NetPP28_1' on L2 at (128.91, 223.49), 24.89 mm, running ALONG the bare copper for 20.63 mm, not across it over copper of NetPP52_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetPP52_1' on TOP_LAYER at (130.18, 225.34), 22.63 mm, running ALONG the bare copper for 19.76 mm, not across it over copper of NetPP28_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP127_1' on L2 at (217.17, 133.48), 6.07 mm over copper of 3.3V, SCL3, SDA3, VSS, not a plane; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'SCL3' on TOP_LAYER at (216.09, 131.13), 4.17 mm over copper of NetPP127_1, not a plane; other side: none: the signal layer is outermost / 'SDA3' on TOP_LAYER at (218.25, 131.76), 4.17 mm over copper of NetPP127_1, not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP127_1' on L2 at (213.11, 171.7), 5.89 mm over copper of NetPP35_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP35_1' on L3 at (214.19, 168.19), 7.71 mm over copper of NetPP127_1, not a plane, to the end of the track; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2
      • one crossing of two tracks, seen from each: 'NetPP102_1' on L3 at (176.68, 118.59), 4.94 mm over copper of NetPP124_1, not a plane, to the end of the track; other side: GND on L4, 0.2 mm from the track against 0.2 mm to L2: 50% of the return on L2 / 'NetPP124_1' on L2 at (177.8, 119.06), 4.87 mm over copper of NetPP102_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L2%3Ahole%20126.4%2C85.81%7C245.71%2C271.57 serves each with its own layer_image region; all of them lie in x 126.65..225.14, y 114.55..266.43 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2:hole 228.48,165.4|266.03,258.8715 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L2, the GND plane on L3, the GND plane on L4, the GND plane on L5, the GND plane on L6, the GND plane on L7 and the GND plane on TOP_LAYER at 3 places, the longest 127.37 mm; 35 over tracks of other nets routed inside it (fastest: NetPP119_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP96_1' on L7, the GND plane on L6 has 127.37 mm under the track with copper of NetPP85_1, not a plane, at (260.99, 197.48), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 35 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 25 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 120.16 mm). 3 places on 15 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 106.08..266.03, y 95.56..271.57 and the hole at x 200.35..266.03, y 95.56..258.87 and the hole at x 228.48..266.03, y 165.4..258.87 and the hole at x 234.11..266.03, y 124.79..258.87. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 36 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: 'NetPP38_1' on L2 at (259.91, 184.63), 5.89 mm over copper of NetPP62_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP50_1' on L5 at (260.99, 220.62), 51.12 mm, running ALONG the bare copper for 41.58 mm, not across it over copper of NetPP73_1, GND, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP50_1' on L5 at (260.99, 222.57), 51.12 mm, running ALONG the bare copper for 45.38 mm, not across it over copper of NetPP85_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP62_1' on L3 at (260.99, 187.24), 5.89 mm over copper of NetPP38_1, not a plane; other side: no plane on L4 / 'NetPP62_1' on L3 at (260.99, 199.07), 88.38 mm, running ALONG the bare copper for 86.13 mm, not across it over copper of NetPP73_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP73_1' on L4 at (260.99, 199.07), 87.43 mm, running ALONG the bare copper for 80.31 mm, not across it over copper of NetPP62_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP73_1' on L4 at (260.99, 220.7), 46.79 mm, running ALONG the bare copper for 41.28 mm, not across it over copper of NetPP50_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP85_1' on L6 at (260.99, 222.57), 54.41 mm, running ALONG the bare copper for 45.54 mm, not across it over copper of NetPP50_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP85_1' on L6 at (260.99, 197.52), 124.83 mm, running ALONG the bare copper for 119.92 mm, not across it over copper of NetPP96_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP96_1' on L7 at (260.99, 197.48), 127.37 mm, running ALONG the bare copper for 120.16 mm, not across it over copper of NetPP85_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER
      • one stretch, cleared on 24 reference layers: 'NetPP119_1' on BOTTOM_LAYER at (253.37, 202.49), 77.27 mm, running ALONG the bare copper for 69.95 mm, not across it over copper of NetPP37_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP25_1' on L2 at (253.37, 216.77), 44.4 mm, running ALONG the bare copper for 39.49 mm, not across it over copper of NetPP49_1, not a plane, to the end of the track; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP25_1' on L2 at (253.37, 233.06), 5.94 mm, running ALONG the bare copper for 3.03 mm, not across it over copper of PP107, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP37_1' on L7 at (253.37, 202.57), 76.85 mm, running ALONG the bare copper for 69.82 mm, not across it over copper of NetPP119_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP37_1' on L7 at (242.89, 171.77), 16.31 mm over copper of NetPP83_1, NetPP61_1, not a plane, to the end of the track; other side: GND on BOTTOM_LAYER, 0.2 mm from the track against 0.2 mm to L6: 50% of the return on L6 / 'NetPP37_1' on L7 at (253.37, 207.61), 64.57 mm, running ALONG the bare copper for 57.24 mm, not across it over copper of NetPP61_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP38_1' on L2 at (254.44, 179.17), 5.89 mm over copper of NetPP49_1, not a plane; other side: GND on TOP_LAYER, 0.2 mm from the track against 0.2 mm to L3: 50% of the return on L3 / 'NetPP49_1' on L3 at (253.37, 179.62), 5.89 mm over copper of NetPP38_1, not a plane; other side: no plane on L4 / 'NetPP49_1' on L3 at (253.37, 216.77), 46.94 mm, running ALONG the bare copper for 39.94 mm, not across it over copper of NetPP25_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP49_1' on L3 at (253.37, 205.11), 95.32 mm, running ALONG the bare copper for 90.41 mm, not across it over copper of NetPP72_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP50_1' on L5 at (246.38, 165.99), 5.89 mm over copper of NetPP72_1, not a plane; other side: no plane on L6 / 'NetPP50_1' on L5 at (254.44, 193.48), 5.89 mm over copper of NetPP72_1, not a plane; other side: no plane on L6 / 'NetPP50_1' on L5 at (246.38, 172.47), 43.81 mm, running ALONG the bare copper for 37.93 mm, not across it over copper of NetPP61_1, not a plane, to the end of the track; other side: GND on L4, 0.7 mm from the track against 0.2 mm to L6: 78% of the return on L6 / 'NetPP61_1' on L6 at (246.38, 172.44), 41.59 mm, running ALONG the bare copper for 35.6 mm, not across it over copper of NetPP50_1, not a plane; other side: no plane on L7 / 'NetPP61_1' on L6 at (253.37, 222.57), 54.41 mm, running ALONG the bare copper for 45.36 mm, not across it over copper of NetPP84_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP61_1' on L6 at (246.38, 176.79), 5.89 mm over copper of NetPP37_1, not a plane; other side: no plane on L5 / 'NetPP61_1' on L6 at (253.37, 207.61), 62.03 mm, running ALONG the bare copper for 57.12 mm, not across it over copper of NetPP37_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP72_1' on L4 at (253.37, 205.14), 97.86 mm, running ALONG the bare copper for 90.54 mm, not across it over copper of NetPP49_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP72_1' on L4 at (245.3, 163.39), 5.89 mm over copper of NetPP50_1, not a plane; other side: no plane on L3 / 'NetPP72_1' on L4 at (253.37, 193.93), 5.89 mm over copper of NetPP50_1, not a plane; other side: no plane on L3 / 'NetPP72_1' on L4 at (253.37, 220.62), 46.79 mm, running ALONG the bare copper for 41.18 mm, not across it over copper of NetPP84_1, not a plane, to the end of the track; other side: no plane on L3 / 'NetPP83_1' on L6 at (239.4, 166.75), 5.89 mm over copper of NetPP37_1, not a plane; other side: GND on L5, 0.2 mm from the track against 0.2 mm to L7: 50% of the return on L7 / 'NetPP84_1' on L5 at (253.37, 220.7), 51.12 mm, running ALONG the bare copper for 41.48 mm, not across it over copper of NetPP72_1, GND, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP84_1' on L5 at (253.37, 222.57), 51.12 mm, running ALONG the bare copper for 45.38 mm, not across it over copper of NetPP61_1, not a plane, to the end of the track; other side: no plane on L4
      • one crossing of two tracks, seen from each: 'NetPP26_1' on TOP_LAYER at (262.26, 214.88), 43.56 mm, running ALONG the bare copper for 40.69 mm, not across it over copper of NetPP38_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP38_1' on L2 at (263.53, 213.02), 45.82 mm, running ALONG the bare copper for 40.34 mm, not across it over copper of NetPP26_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L2%3Ahole%20228.48%2C165.4%7C266.03%2C258.87 serves each with its own layer_image region; all of them lie in x 233.51..265.78, y 131.33..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:144.15,137.12'NetPP99_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP99_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP99_1' on L4, the GND plane on L3 has 1 mm under the track with no copper, at (144.15, 137.12), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP99_1' on L4 at (144.15, 137.12), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A144.15%2C137.12 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 135.62..138.62 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:144.15,145.79'NetPP99_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP99_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP99_1' on L4, the GND plane on L3 has 1 mm under the track with no copper, at (144.15, 145.79), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP99_1' on L4 at (144.15, 145.79), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A144.15%2C145.79 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 144.29..147.29 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:144.15,165.28'NetPP99_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP99_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP99_1' on L4, the GND plane on L3 has 1 mm under the track with no copper, at (144.15, 165.28), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP99_1' on L4 at (144.15, 165.28), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A144.15%2C165.28 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 163.78..166.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:144.15,184.77'NetPP99_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP99_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP99_1' on L4, the GND plane on L3 has 1 mm under the track with no copper, at (144.15, 184.77), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP99_1' on L4 at (144.15, 184.77), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A144.15%2C184.77 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 183.27..186.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:146.67,199.92'NetPP8_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 7.49 mm (fastest: NetPP8_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP8_1' on L2, the GND plane on L3 has 7.49 mm under the track with no copper, at (146.67, 199.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP8_1' on L2 at (146.67, 199.92), 7.49 mm over no copper; other side: no plane on TOP_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A146.67%2C199.92 serves each with its own layer_image region; all of them lie in x 145.67..147.67, y 195.18..204.67 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:146.69,199.92'NetPP99_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 7.45 mm (fastest: NetPP99_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP99_1' on L4, the GND plane on L3 has 7.45 mm under the track with no copper, at (146.69, 199.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP99_1' on L4 at (146.69, 199.92), 7.45 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A146.69%2C199.92 serves each with its own layer_image region; all of them lie in x 145.69..147.69, y 195.2..204.65 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:149.86,136.05'NetPP121_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 1.68 mm (fastest: NetPP121_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP121_1' on L4, the GND plane on L3 has 1.68 mm under the track with no copper, at (149.86, 136.05), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP121_1' on L4 at (149.86, 136.05), 1.68 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A149.86%2C136.05 serves each with its own layer_image region; all of them lie in x 148.86..150.86, y 134.21..137.89 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:192.41,251.46'NetPP125_1' crosses where the GND plane on L3 and the GND plane on TOP_LAYER is drawn back round copper of PP103, PP114, PP131, PP21, PP39, PP45, PP5, PP80, at 1 place, the longest 29.23 mm; 1 cleared on both sides of the track (fastest: NetPP125_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP125_1' on L2, the GND plane on TOP_LAYER has 29.23 mm under the track with copper of PP21, PP5, PP45, PP103, PP39, PP114, PP80, PP131, not a plane, at (192.41, 245.11), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 11.33 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 2 reference layers: 'NetPP125_1' on L2 at (192.41, 251.46), 27.26 mm, running ALONG the bare copper for 10.1 mm, not across it over copper of GND, not a plane, to the end of the track; other side: no plane on TOP_LAYER / 'NetPP125_1' on L2 at (192.41, 245.11), 29.23 mm, running ALONG the bare copper for 11.33 mm, not across it over copper of PP21, PP5, PP45, PP103, PP39, PP114, PP80, PP131, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A192.41%2C251.46 serves each with its own layer_image region; all of them lie in x 188.87..193.41, y 230.67..261.35 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:194.95,107.89'NetPP125_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 2.05 mm (fastest: NetPP125_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP125_1' on L2, the GND plane on L3 has 2.05 mm under the track with no copper, at (194.95, 107.89), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP125_1' on L2 at (194.95, 107.89), 2.05 mm over no copper; other side: no plane on TOP_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A194.95%2C107.89 serves each with its own layer_image region; all of them lie in x 193.95..195.95, y 105.86..109.91 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L3:235.83,195.16'NetPP15_1' crosses where the outline of the GND plane on L3 is drawn back, at 1 place, the longest 0.92 mm (fastest: NetPP15_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP15_1' on L2, the GND plane on L3 has 0.92 mm under the track with no copper, at (235.83, 195.16), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP15_1' on L2 at (235.83, 195.16), 0.92 mm over no copper; other side: no plane on TOP_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L3%3A235.83%2C195.16 serves each with its own layer_image region; all of them lie in x 234.5..237.15, y 193.83..196.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L4:hole 106.08,95.56|266.03,271.5712 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L3, the GND plane on L4, the GND plane on L5, the GND plane on L6 and the GND plane on L7 at 4 places, the longest 134.21 mm; 23 over tracks of other nets routed inside it (fastest: NetPP105_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP133_1' on L7, the GND plane on BOTTOM_LAYER has 134.21 mm under the track with copper of NetPP116_1, NetPP93_1, NetPP46_1, not a plane, at (212.73, 233.68), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 23 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 17 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 100.42 mm). 4 places on 12 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 106.08..266.03, y 95.56..271.57 and the hole at x 200.35..266.03, y 95.56..258.87. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 5 of the 24 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 18 reference layers: 'NetPP105_1' on L4 at (220.35, 227.33), 32.86 mm, running ALONG the bare copper for 27.35 mm, not across it over copper of NetPP23_1, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.7 mm to L5: 22% of the return on L5 / 'NetPP116_1' on BOTTOM_LAYER at (200.03, 157.48), 72.47 mm, running ALONG the bare copper for 43.57 mm, not across it over copper of NetPP132_1, NetPP133_1, not a plane; other side: none: the signal layer is outermost / 'NetPP116_1' on BOTTOM_LAYER at (212.73, 233.72), 45.41 mm, running ALONG the bare copper for 38.18 mm, not across it over copper of NetPP133_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP133_1' on L7 at (212.73, 233.68), 134.21 mm, running ALONG the bare copper for 100.42 mm, not across it over copper of NetPP116_1, NetPP93_1, NetPP46_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP133_1' on L7 at (205.74, 186.05), 5.89 mm over copper of NetPP13_1, not a plane; other side: no plane on BOTTOM_LAYER / 'NetPP133_1' on L7 at (205.74, 202.4), 15.08 mm, running ALONG the bare copper for 10.74 mm, not across it over no copper; other side: no plane on BOTTOM_LAYER / 'NetPP133_1' on L7 at (212.73, 232.45), 41.07 mm, running ALONG the bare copper for 33.85 mm, not across it over copper of NetPP13_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP13_1' on L6 at (212.73, 201.37), 29.93 mm, running ALONG the bare copper for 12.38 mm, not across it over copper of NetPP34_1, NetPP23_1, not a plane, to the end of the track; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP13_1' on L6 at (212.73, 230.5), 38.53 mm, running ALONG the bare copper for 29.48 mm, not across it over copper of NetPP34_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP13_1' on L6 at (204.5, 186.34), 6.34 mm over copper of NetPP133_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP13_1' on L6 at (212.73, 232.37), 38.53 mm, running ALONG the bare copper for 33.52 mm, not across it over copper of NetPP133_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP23_1' on L5 at (220.35, 227.29), 39.74 mm, running ALONG the bare copper for 28.17 mm, not across it over copper of NetPP105_1, GND, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP23_1' on L5 at (211.46, 200.21), 21.4 mm, running ALONG the bare copper for 12.53 mm, not across it over copper of NetPP13_1, not a plane; other side: GND on L4, 0.7 mm from the track against 0.2 mm to L6: 78% of the return on L6 / 'NetPP23_1' on L5 at (220.35, 230.51), 39.74 mm, running ALONG the bare copper for 33.9 mm, not across it over copper of NetPP47_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP34_1' on L5 at (205.74, 186.05), 5.89 mm over copper of NetPP13_1, not a plane; other side: no plane on L4 / 'NetPP34_1' on L5 at (212.73, 230.51), 35.25 mm, running ALONG the bare copper for 29.51 mm, not across it over copper of NetPP13_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP46_1' on BOTTOM_LAYER at (205.74, 194.27), 59.24 mm, running ALONG the bare copper for 44.38 mm, not across it over copper of NetPP132_1, NetPP133_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP47_1' on L6 at (220.35, 230.47), 43.02 mm, running ALONG the bare copper for 34.15 mm, not across it over copper of NetPP23_1, not a plane, to the end of the track; other side: no plane on L7
      • one crossing of two tracks, seen from each: 'NetPP74_1' on L3 at (118.75, 227.37), 28.37 mm, running ALONG the bare copper for 23.47 mm, not across it over copper of NetPP86_1, not a plane, to the end of the track; other side: GND on L2, 0.2 mm from the track against 0.2 mm to L4: 50% of the return on L4 / 'NetPP86_1' on L4 at (118.75, 227.29), 30.91 mm, running ALONG the bare copper for 23.79 mm, not across it over copper of NetPP74_1, not a plane, to the end of the track; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3
      • one crossing of two tracks, seen from each: 'NetPP27_1' on L3 at (127.13, 169.71), 6.79 mm over copper of NetPP86_1, not a plane, to the end of the track; other side: no plane on L2 / 'NetPP86_1' on L4 at (125.73, 172.63), 5.89 mm over copper of NetPP27_1, not a plane; other side: GND on L5, 0.7 mm from the track against 0.2 mm to L3: 78% of the return on L3
      • one crossing of two tracks, seen from each: 'NetPP16_1' on L5 at (126.81, 178.01), 5.89 mm over copper of NetPP86_1, not a plane; other side: GND on L6, 0.2 mm from the track against 0.7 mm to L4: 22% of the return on L4 / 'NetPP86_1' on L4 at (125.73, 180.62), 5.89 mm over copper of NetPP16_1, not a plane; other side: GND on L3, 0.2 mm from the track against 0.7 mm to L5: 22% of the return on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L4%3Ahole%20106.08%2C95.56%7C266.03%2C271.57 serves each with its own layer_image region; all of them lie in x 117.75..223.89, y 113.34..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L5:hole 106.08,95.56|266.03,271.5724 nets cross one void in the GND plane on BOTTOM_LAYER, the GND plane on L3, the GND plane on L5, the GND plane on L6 and the GND plane on L7 at 12 places, the longest 153.23 mm; 6 cleared on both sides of the track; 39 over tracks of other nets routed inside it (fastest: NetPP101_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP123_1' on L7, the GND plane on BOTTOM_LAYER has 153.23 mm under the track with copper of NetPP101_1, NetPP113_1, NetPP134_1, not a plane, at (172.09, 233.68), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 39 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 35 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 129.29 mm). 12 places on 24 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 106.08..266.03, y 95.56..271.57. At 6 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 2 of the 39 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: 'NetPP101_1' on BOTTOM_LAYER at (172.09, 233.76), 58.93 mm, running ALONG the bare copper for 45.03 mm, not across it over copper of NetPP4_1, NetPP123_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP113_1' on BOTTOM_LAYER at (172.09, 202.81), 21.46 mm, running ALONG the bare copper for 11.09 mm, not across it over copper of NetPP4_1, NetPP123_1, not a plane; other side: none: the signal layer is outermost / 'NetPP113_1' on BOTTOM_LAYER at (177.8, 165.1), 28.75 mm, running ALONG the bare copper for 24.05 mm, not across it over copper of NetPP123_1, not a plane; other side: none: the signal layer is outermost / 'NetPP123_1' on L7 at (172.09, 233.68), 153.23 mm, running ALONG the bare copper for 122.56 mm, not across it over copper of NetPP101_1, NetPP113_1, NetPP134_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP123_1' on L7 at (172.09, 232.45), 41.07 mm, running ALONG the bare copper for 34.6 mm, not across it over copper of NetPP129_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP123_1' on L7 at (177.8, 167.04), 67 mm, running ALONG the bare copper for 55.8 mm, not across it over copper of NetPP129_1, NetPP56_1, not a plane; other side: no plane on BOTTOM_LAYER / 'NetPP129_1' on L6 at (172.09, 218.8), 117.75 mm, running ALONG the bare copper for 103.63 mm, not across it over copper of NetPP10_1, NetPP67_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP129_1' on L6 at (172.09, 232.45), 57.2 mm, running ALONG the bare copper for 52.23 mm, not across it over copper of NetPP123_1, NetPP4_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP129_1' on L6 at (177.8, 166.97), 85.73 mm, running ALONG the bare copper for 66.89 mm, not across it over copper of NetPP123_1, NetPP130_1, not a plane; other side: no plane on L5 / 'NetPP130_1' on L7 at (183.52, 167.79), 147.56 mm, running ALONG the bare copper for 129.29 mm, not across it over copper of NetPP129_1, NetPP56_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP134_1' on BOTTOM_LAYER at (177.8, 115.15), 125.08 mm, running ALONG the bare copper for 101.51 mm, not across it over copper of NetPP130_1, NetPP123_1, not a plane; other side: none: the signal layer is outermost / 'NetPP32_1' on L5 at (184.79, 232.41), 89.89 mm, running ALONG the bare copper for 79.73 mm, not across it over copper of NetPP56_1, not a plane, to the end of the track; other side: no plane on L4 / 'NetPP4_1' on L7 at (167.01, 206.51), 24.03 mm, running ALONG the bare copper for 8.53 mm, not across it over copper of NetPP101_1, NetPP113_1, not a plane, to the end of the track; other side: no plane on L6 / 'NetPP56_1' on L6 at (184.79, 232.41), 91.32 mm, running ALONG the bare copper for 76.35 mm, not across it over copper of NetPP67_1, NetPP32_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP56_1' on L6 at (183.52, 167.79), 68.97 mm, running ALONG the bare copper for 59.43 mm, not across it over copper of NetPP123_1, NetPP130_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP56_1' on L6 at (184.79, 232.41), 38.53 mm, running ALONG the bare copper for 33.62 mm, not across it over copper of NetPP130_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP67_1' on L5 at (177.8, 162.91), 76.48 mm, running ALONG the bare copper for 64.07 mm, not across it over copper of NetPP129_1, NetPP56_1, not a plane, to the end of the track; other side: no plane on L4
      • one stretch, cleared on 2 reference layers: 'NetPP68_1' on L4 at (189.23, 168.95), 97.92 mm, running ALONG the bare copper for 92.75 mm, not across it over copper of NetPP45_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP68_1' on L4 at (187.33, 225.11), 89.23 mm, running ALONG the bare copper for 85.97 mm, not across it over copper of NetPP39_1, not a plane; other side: no plane on L3
      • 'NetPP114_1' on L6 at (187.33, 225.11), 94.23 mm, running ALONG the bare copper for 75.45 mm, not across it over copper of NetPP39_1, NetPP33_1, NetPP57_1, not a plane; other side: no plane on L7
      • one stretch, cleared on 2 reference layers: 'NetPP111_1' on L6 at (149.86, 177.04), 62.02 mm, running ALONG the bare copper for 55.95 mm, not across it over copper of NetPP53_1, not a plane; other side: no plane on L7 / 'NetPP111_1' on L6 at (149.86, 170.65), 74.81 mm, running ALONG the bare copper for 68.75 mm, not across it over copper of NetPP87_1, not a plane; other side: no plane on L5
      • one crossing of two tracks, seen from each: 'NetPP12_1' on L6 at (205.11, 241.58), 47.95 mm, running ALONG the bare copper for 41.96 mm, not across it over copper of NetPP57_1, not a plane, to the end of the track; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5 / 'NetPP57_1' on L5 at (205.11, 241.66), 72.69 mm, running ALONG the bare copper for 59.68 mm, not across it over copper of NetPP12_1, not a plane; other side: no plane on L4
      • one stretch, cleared on 2 reference layers: 'NetPP121_1' on L4 at (149.86, 172.71), 70.74 mm, running ALONG the bare copper for 65.99 mm, not across it over copper of NetPP76_1, not a plane; other side: no plane on L5 / 'NetPP121_1' on L4 at (149.86, 177.04), 62.02 mm, running ALONG the bare copper for 55.95 mm, not across it over copper of NetPP53_1, not a plane; other side: no plane on L3
      • one stretch, cleared on 2 reference layers: 'NetPP110_1' on L6 at (139.07, 232.37), 49.31 mm, running ALONG the bare copper for 40.44 mm, not across it over copper of NetPP53_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP110_1' on L6 at (139.07, 234.32), 49.31 mm, running ALONG the bare copper for 44.4 mm, not across it over copper of NetPP87_1, not a plane, to the end of the track; other side: no plane on L5
      • one stretch, cleared on 2 reference layers: 'NetPP99_1' on L4 at (139.07, 227.33), 41.69 mm, running ALONG the bare copper for 34.56 mm, not across it over copper of NetPP76_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP99_1' on L4 at (139.07, 228.64), 41.69 mm, running ALONG the bare copper for 36.18 mm, not across it over copper of NetPP53_1, not a plane, to the end of the track; other side: no plane on L3
      • one stretch, cleared on 2 reference layers: 'NetPP66_1' on L4 at (159.39, 229.99), 30.91 mm, running ALONG the bare copper for 23.79 mm, not across it over copper of NetPP3_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP66_1' on L4 at (159.39, 231.3), 30.05 mm, running ALONG the bare copper for 25.4 mm, not across it over copper of NetPP122_1, not a plane, to the end of the track; other side: no plane on L3
      • one crossing of two tracks, seen from each: 'NetPP120_1' on L7 at (194.31, 197.15), 25.38 mm, running ALONG the bare copper for 16.83 mm, not across it over copper of NetPP12_1, NetPP2_1, not a plane; other side: no plane on BOTTOM_LAYER / 'NetPP12_1' on L6 at (197.17, 190.26), 14.17 mm over copper of NetPP33_1, NetPP57_1, not a plane, to the end of the track; other side: no plane on L7 / 'NetPP12_1' on L6 at (197.17, 190.26), 14.17 mm over copper of NetPP120_1, NetPP132_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP2_1' on L6 at (193.16, 205.74), 6.09 mm over copper of NetPP120_1, not a plane, to the end of the track; other side: no plane on L5 / 'NetPP33_1' on L5 at (194.31, 197.15), 25.38 mm, running ALONG the bare copper for 16.83 mm, not across it over copper of NetPP12_1, NetPP2_1, not a plane; other side: no plane on L4
      • 'NetPP59_1' on L4 at (215.84, 147.45), 6.59 mm over copper of NetPP94_1, not a plane, to the end of the track; other side: no plane on L3
      • 'NetPP20_1' on L6 at (174.8, 180.1), 15.79 mm, running ALONG the bare copper for 10.64 mm, not across it over copper of NetPP10_1, not a plane, to the end of the track; other side: GND on L7, 0.2 mm from the track against 0.2 mm to L5: 50% of the return on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L5%3Ahole%20106.08%2C95.56%7C266.03%2C271.57 serves each with its own layer_image region; all of them lie in x 138.07..220.25, y 87.45..261.76 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L6:192.41,245.65'NetPP120_1' crosses where the outline of the GND plane on L6 is drawn back, at 1 place, the longest 35.63 mm (fastest: NetPP120_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP120_1' on L7, the GND plane on L6 has 35.63 mm under the track with copper of GND, not a plane, at (192.41, 245.65), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 12.61 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP120_1' on L7 at (192.41, 245.65), 35.63 mm, running ALONG the bare copper for 12.61 mm, not across it over copper of GND, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L6%3A192.41%2C245.65 serves each with its own layer_image region; all of them lie in x 188.87..193.41, y 232.64..268.97 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L6:205.74,202.4'NetPP34_1' crosses where the outline of the GND plane on L6 is drawn back, at 1 place, the longest 15.08 mm (fastest: NetPP34_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP34_1' on L5, the GND plane on L6 has 15.08 mm under the track with no copper, at (205.74, 202.4), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 10.74 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP34_1' on L5 at (205.74, 202.4), 15.08 mm, running ALONG the bare copper for 10.74 mm, not across it over no copper; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L6%3A205.74%2C202.4 serves each with its own layer_image region; all of them lie in x 204.74..208.19, y 194.89..211.36 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:134.62,199.92'NetPP64_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 4.15 mm (fastest: NetPP64_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP64_1' on BOTTOM_LAYER, the GND plane on L7 has 4.15 mm under the track with no copper, at (134.62, 199.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP64_1' on BOTTOM_LAYER at (134.62, 199.92), 4.15 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A134.62%2C199.92 serves each with its own layer_image region; all of them lie in x 133.62..135.62, y 196.85..203 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:144.15,137.12'NetPP110_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP110_1' on L6, the GND plane on L7 has 1 mm under the track with no copper, at (144.15, 137.12), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP110_1' on L6 at (144.15, 137.12), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A144.15%2C137.12 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 135.62..138.62 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:144.15,145.79'NetPP110_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP110_1' on L6, the GND plane on L7 has 1 mm under the track with no copper, at (144.15, 145.79), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP110_1' on L6 at (144.15, 145.79), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A144.15%2C145.79 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 144.29..147.29 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:144.15,165.282 nets cross where the outline of the GND plane on L7 is drawn back, at 2 places, the longest 1 mm (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP64_1' on BOTTOM_LAYER, the GND plane on L7 has 1 mm under the track with no copper, at (144.15, 165.28), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 places on 2 net(s) cross it, listed below, the longest first. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP110_1' on L6 at (144.15, 165.28), 1 mm over no copper; other side: no plane on L5
      • 'NetPP64_1' on BOTTOM_LAYER at (144.15, 165.28), 1 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A144.15%2C165.28 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 163.78..166.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:144.15,184.77'NetPP110_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 1 mm (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP110_1' on L6, the GND plane on L7 has 1 mm under the track with no copper, at (144.15, 184.77), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP110_1' on L6 at (144.15, 184.77), 1 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A144.15%2C184.77 serves each with its own layer_image region; all of them lie in x 143.15..145.15, y 183.27..186.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:146.69,199.92'NetPP110_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 7.45 mm (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP110_1' on L6, the GND plane on L7 has 7.45 mm under the track with no copper, at (146.69, 199.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP110_1' on L6 at (146.69, 199.92), 7.45 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A146.69%2C199.92 serves each with its own layer_image region; all of them lie in x 145.69..147.69, y 195.2..204.65 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:205.11,204.71'NetPP12_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 15.08 mm (fastest: NetPP12_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP12_1' on L6, the GND plane on L7 has 15.08 mm under the track with no copper, at (205.11, 204.71), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 10.74 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP12_1' on L6 at (205.11, 204.71), 15.08 mm, running ALONG the bare copper for 10.74 mm, not across it over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A205.11%2C204.71 serves each with its own layer_image region; all of them lie in x 202.66..206.11, y 195.75..212.23 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:225.43,199.92'NetPP117_1' crosses where the outline of the GND plane on L7 is drawn back, at 1 place, the longest 7.45 mm (fastest: NetPP117_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP117_1' on L6, the GND plane on L7 has 7.45 mm under the track with no copper, at (225.43, 199.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP117_1' on L6 at (225.43, 199.92), 7.45 mm over no copper; other side: no plane on L5

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3A225.43%2C199.92 serves each with its own layer_image region; all of them lie in x 224.43..226.43, y 195.2..204.65 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7:hole 234.11,124.79|266.03,258.87'NetPP108_1' crosses one void in the GND plane on L7 at 1 place, the longest 113.47 mm; 1 over tracks of other nets routed inside it (fastest: NetPP108_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP108_1' on BOTTOM_LAYER, the GND plane on L7 has 113.47 mm under the track with copper of NetPP96_1, not a plane, at (260.99, 198.75), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 106.35 mm). What cleared it: the hole at x 234.11..266.03, y 124.79..258.87. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP108_1' on BOTTOM_LAYER at (260.99, 198.75), 113.47 mm, running ALONG the bare copper for 106.35 mm, not across it over copper of NetPP96_1, not a plane, to the end of the track; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L7%3Ahole%20234.11%2C124.79%7C266.03%2C258.87 serves each with its own layer_image region; all of them lie in x 259.99..264.53, y 142.1..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@TOP_LAYER:118.54,155.54'NetPP40_1' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 8.08 mm (fastest: NetPP40_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP40_1' on L2, the GND plane on TOP_LAYER has 8.08 mm under the track with no copper, at (118.54, 155.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP40_1' on L2 at (118.54, 155.54), 8.08 mm over no copper; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40TOP_LAYER%3A118.54%2C155.54 serves each with its own layer_image region; all of them lie in x 113.5..123.58, y 154.54..156.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@TOP_LAYER:177.17,204.26'NetPP79_1' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 2.93 mm (fastest: NetPP79_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP79_1' on L2, the GND plane on TOP_LAYER has 2.93 mm under the track with no copper, at (177.17, 204.26), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP79_1' on L2 at (177.17, 204.26), 2.93 mm over no copper; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40TOP_LAYER%3A177.17%2C204.26 serves each with its own layer_image region; all of them lie in x 176.17..178.17, y 201.79..206.73 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@TOP_LAYER:181.33,195.86'NetPP79_1' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 4.73 mm (fastest: NetPP79_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP79_1' on L2, the GND plane on TOP_LAYER has 4.73 mm under the track with no copper, at (181.33, 195.86), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP79_1' on L2 at (181.33, 195.86), 4.73 mm over no copper; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40TOP_LAYER%3A181.33%2C195.86 serves each with its own layer_image region; all of them lie in x 178.79..183.88, y 192.96..198.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@TOP_LAYER:182.88,181.49'NetPP79_1' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 16.23 mm (fastest: NetPP79_1 at 100 ps 10-90 %, ASSUMED)

      Along 'NetPP79_1' on L2, the GND plane on TOP_LAYER has 16.23 mm under the track with no copper, at (182.88, 181.49), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 13.18 mm). No hole cleared it: the outline of the pour at x 78.16..293.95, y 78.47..338.25 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP79_1' on L2 at (182.88, 181.49), 16.23 mm, running ALONG the bare copper for 13.18 mm, not across it over no copper; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40TOP_LAYER%3A182.88%2C181.49 serves each with its own layer_image region; all of them lie in x 181.88..183.88, y 172.38..190.61 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@BOTTOM_LAYER|L7Tracks on BOTTOM_LAYER and L7 cross each other at 9 places, each layer the other's reference with its pour cleared round its own tracks, the longest 177.87 mm; 11 run ALONG the cut round another net's track (fastest: NetPP101_1 at 100 ps 10-90 %, ASSUMED)

      BOTTOM_LAYER and L7 each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 9 place(s) on 11 net(s), 2 of them seen from both tracks (each counted once). 11 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 140.44 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP135_1' on BOTTOM_LAYER at (200.03, 219.67), 177.87 mm, running ALONG the bare copper for 139.07 mm, not across it over copper of NetPP120_1, NetPP132_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'NetPP131_1' on BOTTOM_LAYER at (189.23, 165.79), 159.15 mm, running ALONG the bare copper for 140.44 mm, not across it over copper of NetPP120_1, NetPP80_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'NetPP93_1' on BOTTOM_LAYER at (217.17, 184.02), 105.35 mm, running ALONG the bare copper for 98.13 mm, not across it over copper of NetPP70_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP24_1' on BOTTOM_LAYER at (233.05, 233.72), 58.88 mm, running ALONG the bare copper for 51.56 mm, not across it over copper of NetPP48_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP48_1' on L7 at (233.05, 233.68), 86.09 mm, running ALONG the bare copper for 81.72 mm, not across it over copper of NetPP24_1, not a plane, to the end of the track; other side: no plane on L6
      • 'NetPP134_1' on BOTTOM_LAYER at (187.33, 233.64), 45.01 mm, running ALONG the bare copper for 36.59 mm, not across it over copper of NetPP130_1, NetPP80_1, not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: 'NetPP64_1' on BOTTOM_LAYER at (139.07, 233.68), 42.75 mm, running ALONG the bare copper for 36.49 mm, not across it over copper of NetPP87_1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetPP87_1' on L7 at (139.07, 233.68), 41.71 mm, running ALONG the bare copper for 36.16 mm, not across it over copper of NetPP64_1, not a plane, to the end of the track; other side: no plane on L6
      • 'NetPP113_1' on BOTTOM_LAYER at (172.09, 126.07), 37.22 mm, running ALONG the bare copper for 31.01 mm, not across it over copper of NetPP123_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'NetPP30_1' on BOTTOM_LAYER at (157.93, 171.61), 18.66 mm, running ALONG the bare copper for 14.38 mm, not across it over copper of NetPP54_1, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'NetPP101_1' on BOTTOM_LAYER at (166.37, 144.74), 12.24 mm, running ALONG the bare copper for 6.41 mm, not across it over copper of NetPP77_1, not a plane; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3Arouted%40BOTTOM_LAYER%7CL7 serves each with its own layer_image region; all of them lie in x 136.59..234.05, y 87.17..256.27 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@L5|L62 nets on L5 cross the tracks routed through the GND pour on L6 at 3 places, the longest 35.25 mm; 2 run ALONG the cut round another net's track (fastest: NetPP33_1 at 100 ps 10-90 %, ASSUMED)

      The GND pour on L6 is cleared round tracks routed through it, and tracks on L5, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 3 place(s) on 2 net(s). 2 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 29.95 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetPP33_1' on L5 at (200.03, 230.51), 35.25 mm, running ALONG the bare copper for 29.95 mm, not across it over copper of NetPP2_1, not a plane, to the end of the track; other side: no plane on L4
      • 'NetPP57_1' on L5 at (191.68, 152.83), 20.49 mm, running ALONG the bare copper for 12.93 mm, not across it over copper of NetPP114_1, not a plane, to the end of the track; other side: no plane on L4
      • 'NetPP33_1' on L5 at (194.31, 170.26), 10.9 mm over copper of NetPP114_1, not a plane, to the end of the track; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3Arouted%40L5%7CL6 serves each with its own layer_image region; all of them lie in x 190.68..203.57, y 144.79..248.65 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@L6|L7Tracks on L6 and L7 cross each other at 5 places, each layer the other's reference with its pour cleared round its own tracks, the longest 67.36 mm; 4 run ALONG the cut round another net's track (fastest: NetPP110_1 at 100 ps 10-90 %, ASSUMED)

      L6 and L7 each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 5 place(s) on 6 net(s), 1 of them seen from both tracks (each counted once). 4 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 62.45 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 2 of the 6 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: 'NetPP132_1' on L7 at (200.03, 230.69), 63.86 mm, running ALONG the bare copper for 55.94 mm, not across it over copper of NetPP12_1, NetPP2_1, not a plane, to the end of the track; other side: no plane on BOTTOM_LAYER / 'NetPP2_1' on L6 at (200.03, 230.76), 41.83 mm, running ALONG the bare copper for 36.92 mm, not across it over copper of NetPP132_1, not a plane, to the end of the track; other side: no plane on L5
      • 'NetPP120_1' on L7 at (194.31, 151.13), 49.07 mm, running ALONG the bare copper for 42.34 mm, not across it over copper of NetPP114_1, not a plane; other side: no plane on BOTTOM_LAYER
      • 'NetPP123_1' on L7 at (172.09, 107.69), 5.89 mm over copper of NetPP129_1, not a plane; other side: no plane on BOTTOM_LAYER
      • 'NetPP20_1' on L6 at (167.01, 233.28), 67.36 mm, running ALONG the bare copper for 62.45 mm, not across it over copper of NetPP4_1, not a plane, to the end of the track; other side: GND on L5, 0.2 mm from the track against 0.2 mm to L7: 50% of the return on L7
      • 'NetPP110_1' on L6 at (144.15, 128.95), 5.89 mm over copper of NetPP87_1, not a plane; other side: GND on L5, 0.2 mm from the track against 0.2 mm to L7: 50% of the return on L7

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3Arouted%40L6%7CL7 serves each with its own layer_image region; all of them lie in x 143.15..203.57, y 105.27..266.43 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  2. PartLifecyclemajorOpen

    SHT25 on IC1: the distributor catalogue reports "Obsolete" for Sensirion AG's SHT25

    SHT25 on IC1: the distributor catalogue reports "Obsolete" for Sensirion AG's SHT25 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/SHT25/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2026-10-31, 15 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.

    At IC1

  3. ReferencePlaneDiscontinuityminorOpen

    3 nets cross one void in the GND plane on L2 and the GND plane on TOP_LAYER at 2 places, the longest 14.72 mm; 3 over tracks of other nets routed inside it (fastest: SCL3 at 10 ns 10-90 %, suggested by its name)

    Along 'SDA3' on TOP_LAYER, the GND plane on L2 has 14.72 mm under the track with copper of SCL4, SDA4, not a plane, at (273.05, 328.3), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 3 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 3.22 mm). 2 places on 3 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 259.36..281.62, y 322.79..337.61. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 3 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

    • one crossing of two tracks, seen from each: 'SCL4' on L2 at (271.34, 326.39), 5.04 mm over copper of VSS, SDA3, SCL3, 3.3V, not a plane, to the end of the track; other side: GND on L3, 0.2 mm from the track against 0.2 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'SDA3' on TOP_LAYER at (273.05, 328.3), 14.72 mm, running ALONG the bare copper for 3.22 mm, not across it over copper of SCL4, SDA4, not a plane; other side: none: the signal layer is outermost
    • 'SCL3' on TOP_LAYER at (279.05, 330.2), 12.03 mm, running ALONG the bare copper for 1.76 mm, not across it over copper of SDA4, SCL4, not a plane; other side: none: the signal layer is outermost

    Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/6/reference-planes?group=void%3AGND%40L2%3Ahole%20259.36%2C322.79%7C281.62%2C337.61 serves each with its own layer_image region; all of them lie in x 269.33..282.62, y 323.31..335.01 mm (board frame, Y up).

    Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    At void:GND@L2:hole 259.36,322.79|281.62,337.61

Main parts

Part numberMakerDescriptionWhere
EPK.00.250.NTNJ2
SHT25Humidity and Temperature Sensor ICIC1
SSW-104-02-L-S-RAConnector 4 FemaleJ3
MTLW-106-07-L-D-250Connector 12 MaleJ1, J4
MTLW-116-07-L-D-250Connector 32 MaleJ5, J8, J9
MTLW-111-07-L-D-250Connector 20 MaleJ10, J11, J12, J6, J7
0985-1-15-20-71-14-11-0Test PointPP1, PP10, PP100, PP101, PP102, PP103 and 129 more

About this design

Design
ARRAY PROBE CARD — OHWR0003 R1
Designed in
Altium Designer
Board
8 copper layers, 220 × 264 mm, 439 components, 291 nets
Licence
CERN-OHL-1.2
Source
https://gitlab.com/ohwr/project/array/array-hardware at commit 3ad9dd6a5460
Attribution
CERN Open Hardware Repository, project ohwr/project/array/array-hardware (commit 3ad9dd6a5460d9055e14ee77ac9d389869d6d45e, 2025-04-09). Licence: CERN-OHL-1.2. Source: https://gitlab.com/ohwr/project/array/array-hardware. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)