Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

ARRAY SWITCHING MATRIX

OHWR0004 · revision R1

ARRAY SWITCHING MATRIX (OHWR0004 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 8-layer board of 220 × 230 mm with 1190 components and 1446 nets, published under CERN-OHL-1.2.

review 60% walked · 11 findings: 3 major · 8 minor (406 items)

Open in the interactive viewerRead the full review

ARRAY SWITCHING MATRIX (OHWR0004 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 11 findings: 3 major · 8 minor (406 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. PartLifecyclemajorOpen

    PartLifecycle: 4 part numbers×4

    4 Obsolete · on 13 placements

    At DS1, IC166, IC89, J10

    Each finding, with its own headline
    • DS1SA52-11SRWA on 3 placements (DS1, DS2, DS3): the distributor catalogue reports "Obsolete" for Kingbright's SA52-11SRWA

      SA52-11SRWA on 3 placements (DS1, DS2, DS3): the distributor catalogue reports "Obsolete" for Kingbright's SA52-11SRWA — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/SA52-11SRWA/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • IC166SN74HC595D on 3 placements (IC166, IC167, IC168): the distributor catalogue reports "Obsolete" for Texas Instruments's SN74HC595D

      SN74HC595D on 3 placements (IC166, IC167, IC168): the distributor catalogue reports "Obsolete" for Texas Instruments's SN74HC595D — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/SN74HC595D/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • IC89ISO7221AD on IC89: the distributor catalogue reports "Obsolete" for Texas Instruments's ISO7221AD

      ISO7221AD on IC89: the distributor catalogue reports "Obsolete" for Texas Instruments's ISO7221AD — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/ISO7221AD/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2024-06-21, 877 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.

    • J101-1337543-0 on 6 placements (J10, J2, J4, J5, J6, J7): the distributor catalogue reports "Obsolete" for TE Connectivity AMP Connectors's 1-1337543-0

      1-1337543-0 on 6 placements (J10, J2, J4, J5, J6, J7): the distributor catalogue reports "Obsolete" for TE Connectivity AMP Connectors's 1-1337543-0 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/1-1337543-0/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

  2. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 369 boards×369

    369 checked by the review by Claude walker W4 (Cern session) — 369 different reasons

    At along@L2P:+15V|G1, merged:122.56,201.3|125.1,201.3, merged:122.56,214|125.1,214, merged:122.56,226.7|125.1,226.7, merged:122.56,239.4|125.1,239.4, merged:122.56,252.1|125.1,252.1 and 363 more

    Each finding, with its own headline — 100 of 369 shown
    • along@L2P:+15V|G1'NetIC79_3' runs ALONG the split between the +15V and G1 planes on L2P at 2 places, the longest 6.82 mm; the impedance there is not said (fastest: NetIC79_3 at 100 ps 10-90 %, ASSUMED)

      On L2P the +15V and G1 planes part, and 'NetIC79_3' runs down the slot between them at 2 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. At 2 place(s) the impedance cannot be said: the track's centreline is not over the slot. No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'NetIC79_3' on TOP_LAYER at (94.62, 134.39), 6.82 mm, running ALONG the split for 6.82 mm, not across it, impedance not said: the track's centreline is not over the slot; other side: none: the signal layer is outermost
      • 'NetIC79_3' on TOP_LAYER at (92.71, 142.95), 5.87 mm, running ALONG the split for 5.87 mm, not across it, impedance not said: the track's centreline is not over the slot; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=along%40L2P%3A%2B15V%7CG1 serves each with its own layer_image region; all of them lie in x 91.71..95.62, y 129.98..146.89 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,201.3|125.1,201.3'NetIC57_10' crosses between the drills at (122.56, 201.3) and (125.1, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC57_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC57_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 201.3) and (125.1, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.83, 200.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC57_10' on TOP_LAYER at (123.83, 200.97), 1.3 mm between the drills at (122.56, 201.3) and (125.1, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C201.3%7C125.1%2C201.3 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,214|125.1,214'NetIC49_10' crosses between the drills at (122.56, 214) and (125.1, 214), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC49_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC49_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 214) and (125.1, 214), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 214.22). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC49_10' on TOP_LAYER at (123.6, 214.22), 1.3 mm between the drills at (122.56, 214) and (125.1, 214) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C214%7C125.1%2C214 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 212.35..215.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,226.7|125.1,226.7'NetIC41_10' crosses between the drills at (122.56, 226.7) and (125.1, 226.7), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC41_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC41_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 226.7) and (125.1, 226.7), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.83, 226.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC41_10' on TOP_LAYER at (123.83, 226.37), 1.3 mm between the drills at (122.56, 226.7) and (125.1, 226.7) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C226.7%7C125.1%2C226.7 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 225.05..228.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,239.4|125.1,239.4'NetIC33_10' crosses between the drills at (122.56, 239.4) and (125.1, 239.4), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC33_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC33_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 239.4) and (125.1, 239.4), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 239.62). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC33_10' on TOP_LAYER at (123.6, 239.62), 1.3 mm between the drills at (122.56, 239.4) and (125.1, 239.4) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C239.4%7C125.1%2C239.4 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 237.75..240.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,252.1|125.1,252.1'NetIC25_10' crosses between the drills at (122.56, 252.1) and (125.1, 252.1), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC25_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC25_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 252.1) and (125.1, 252.1), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 252.32). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC25_10' on TOP_LAYER at (123.6, 252.32), 1.3 mm between the drills at (122.56, 252.1) and (125.1, 252.1) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C252.1%7C125.1%2C252.1 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 250.45..253.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,267.34|125.1,267.34'NetIC17_10' crosses between the drills at (122.56, 267.34) and (125.1, 267.34), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC17_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC17_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 267.34) and (125.1, 267.34), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 267.56). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC17_10' on TOP_LAYER at (123.6, 267.56), 1.3 mm between the drills at (122.56, 267.34) and (125.1, 267.34) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C267.34%7C125.1%2C267.34 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 265.69..268.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,280.04|125.1,280.04'NetIC9_10' crosses between the drills at (122.56, 280.04) and (125.1, 280.04), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC9_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC9_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 280.04) and (125.1, 280.04), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 280.26). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC9_10' on TOP_LAYER at (123.6, 280.26), 1.3 mm between the drills at (122.56, 280.04) and (125.1, 280.04) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C280.04%7C125.1%2C280.04 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 278.39..281.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:122.56,292.74|125.1,292.74'NetIC1_10' crosses between the drills at (122.56, 292.74) and (125.1, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC1_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC1_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (122.56, 292.74) and (125.1, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (123.6, 292.96). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC1_10' on TOP_LAYER at (123.6, 292.96), 1.3 mm between the drills at (122.56, 292.74) and (125.1, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A122.56%2C292.74%7C125.1%2C292.74 serves each with its own layer_image region; all of them lie in x 122.37..124.83, y 291.09..294.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,184.79|123.83,186.06'A5_1' crosses between the drills at (123.83, 184.79) and (123.83, 186.06), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: A5_1 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (123.83, 184.79) and (123.83, 186.06), and the clearances run together: the straight line from one drill to the next is bare all the way. 'A5_1' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A5_1' on L3 at (123.83, 185.42), 0.28 mm between the drills at (123.83, 184.79) and (123.83, 186.06) in L2P; other side: no plane on L4P
      • 'A5_1' on L3 at (123.83, 185.42), 0.28 mm between the drills at (123.83, 184.79) and (123.83, 186.06) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C184.79%7C123.83%2C186.06 serves each with its own layer_image region; all of them lie in x 122.69..124.96, y 184.42..186.42 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,201.3|126.37,201.3'NetIC57_11' crosses between the drills at (123.83, 201.3) and (126.37, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC57_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC57_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 201.3) and (126.37, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 201.52). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC57_11' on TOP_LAYER at (124.87, 201.52), 1.3 mm between the drills at (123.83, 201.3) and (126.37, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C201.3%7C126.37%2C201.3 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,207.65|126.37,207.65'NetIC57_6' crosses between the drills at (123.83, 207.65) and (126.37, 207.65), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC57_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC57_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 207.65) and (126.37, 207.65), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (125.1, 207.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC57_6' on TOP_LAYER at (125.1, 207.97), 1.3 mm between the drills at (123.83, 207.65) and (126.37, 207.65) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C207.65%7C126.37%2C207.65 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 206.19..209.3 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,214|126.37,214'NetIC49_11' crosses between the drills at (123.83, 214) and (126.37, 214), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC49_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC49_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 214) and (126.37, 214), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (125.1, 213.67). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC49_11' on TOP_LAYER at (125.1, 213.67), 1.3 mm between the drills at (123.83, 214) and (126.37, 214) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C214%7C126.37%2C214 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 212.35..215.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,220.35|126.37,220.35'NetIC49_6' crosses between the drills at (123.83, 220.35) and (126.37, 220.35), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC49_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC49_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 220.35) and (126.37, 220.35), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 220.12). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC49_6' on TOP_LAYER at (124.87, 220.12), 1.3 mm between the drills at (123.83, 220.35) and (126.37, 220.35) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C220.35%7C126.37%2C220.35 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 218.89..222 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,226.7|126.37,226.7'NetIC41_11' crosses between the drills at (123.83, 226.7) and (126.37, 226.7), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC41_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC41_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 226.7) and (126.37, 226.7), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 226.92). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC41_11' on TOP_LAYER at (124.87, 226.92), 1.3 mm between the drills at (123.83, 226.7) and (126.37, 226.7) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C226.7%7C126.37%2C226.7 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 225.05..228.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,233.05|126.37,233.05'NetIC41_6' crosses between the drills at (123.83, 233.05) and (126.37, 233.05), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC41_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC41_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 233.05) and (126.37, 233.05), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 232.82). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC41_6' on TOP_LAYER at (124.87, 232.82), 1.3 mm between the drills at (123.83, 233.05) and (126.37, 233.05) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C233.05%7C126.37%2C233.05 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 231.59..234.7 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,239.4|126.37,239.4'NetIC33_11' crosses between the drills at (123.83, 239.4) and (126.37, 239.4), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC33_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC33_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 239.4) and (126.37, 239.4), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (125.1, 239.07). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC33_11' on TOP_LAYER at (125.1, 239.07), 1.3 mm between the drills at (123.83, 239.4) and (126.37, 239.4) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C239.4%7C126.37%2C239.4 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 237.75..240.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,245.75|126.37,245.75'NetIC33_6' crosses between the drills at (123.83, 245.75) and (126.37, 245.75), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC33_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC33_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 245.75) and (126.37, 245.75), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 245.52). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC33_6' on TOP_LAYER at (124.87, 245.52), 1.3 mm between the drills at (123.83, 245.75) and (126.37, 245.75) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C245.75%7C126.37%2C245.75 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 244.29..247.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,252.1|126.37,252.1'NetIC25_11' crosses between the drills at (123.83, 252.1) and (126.37, 252.1), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC25_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC25_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 252.1) and (126.37, 252.1), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 252.32). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC25_11' on TOP_LAYER at (124.87, 252.32), 1.3 mm between the drills at (123.83, 252.1) and (126.37, 252.1) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C252.1%7C126.37%2C252.1 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 250.45..253.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,258.45|126.37,258.45'NetIC25_6' crosses between the drills at (123.83, 258.45) and (126.37, 258.45), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC25_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC25_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 258.45) and (126.37, 258.45), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 258.22). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC25_6' on TOP_LAYER at (124.87, 258.22), 1.3 mm between the drills at (123.83, 258.45) and (126.37, 258.45) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C258.45%7C126.37%2C258.45 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 256.99..260.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,267.34|126.37,267.34'NetIC17_11' crosses between the drills at (123.83, 267.34) and (126.37, 267.34), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC17_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC17_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 267.34) and (126.37, 267.34), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 267.56). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC17_11' on TOP_LAYER at (124.87, 267.56), 1.3 mm between the drills at (123.83, 267.34) and (126.37, 267.34) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C267.34%7C126.37%2C267.34 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 265.69..268.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,273.69|126.37,273.69'NetIC17_6' crosses between the drills at (123.83, 273.69) and (126.37, 273.69), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC17_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC17_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 273.69) and (126.37, 273.69), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 273.46). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC17_6' on TOP_LAYER at (124.87, 273.46), 1.3 mm between the drills at (123.83, 273.69) and (126.37, 273.69) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C273.69%7C126.37%2C273.69 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 272.23..275.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,280.04|126.37,280.04'NetIC9_11' crosses between the drills at (123.83, 280.04) and (126.37, 280.04), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC9_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC9_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 280.04) and (126.37, 280.04), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (125.1, 279.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC9_11' on TOP_LAYER at (125.1, 279.71), 1.3 mm between the drills at (123.83, 280.04) and (126.37, 280.04) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C280.04%7C126.37%2C280.04 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 278.39..281.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,286.39|126.37,286.39'NetIC9_6' crosses between the drills at (123.83, 286.39) and (126.37, 286.39), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC9_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC9_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 286.39) and (126.37, 286.39), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 286.16). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC9_6' on TOP_LAYER at (124.87, 286.16), 1.3 mm between the drills at (123.83, 286.39) and (126.37, 286.39) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C286.39%7C126.37%2C286.39 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 284.93..288.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,292.74|126.37,292.74'NetIC1_11' crosses between the drills at (123.83, 292.74) and (126.37, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC1_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC1_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 292.74) and (126.37, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (125.1, 292.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC1_11' on TOP_LAYER at (125.1, 292.41), 1.3 mm between the drills at (123.83, 292.74) and (126.37, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C292.74%7C126.37%2C292.74 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 291.09..294.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:123.83,299.09|126.37,299.09'NetIC1_6' crosses between the drills at (123.83, 299.09) and (126.37, 299.09), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC1_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC1_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (123.83, 299.09) and (126.37, 299.09), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (124.87, 298.86). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC1_6' on TOP_LAYER at (124.87, 298.86), 1.3 mm between the drills at (123.83, 299.09) and (126.37, 299.09) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A123.83%2C299.09%7C126.37%2C299.09 serves each with its own layer_image region; all of them lie in x 123.64..126.1, y 297.63..300.74 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,207.65|127.64,207.65'NetIC57_5' crosses between the drills at (125.1, 207.65) and (127.64, 207.65), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC57_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC57_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 207.65) and (127.64, 207.65), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.14, 207.42). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC57_5' on TOP_LAYER at (126.14, 207.42), 1.3 mm between the drills at (125.1, 207.65) and (127.64, 207.65) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C207.65%7C127.64%2C207.65 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 206.19..209.3 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,220.35|127.64,220.35'NetIC49_5' crosses between the drills at (125.1, 220.35) and (127.64, 220.35), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC49_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC49_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 220.35) and (127.64, 220.35), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.14, 220.12). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC49_5' on TOP_LAYER at (126.14, 220.12), 1.3 mm between the drills at (125.1, 220.35) and (127.64, 220.35) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C220.35%7C127.64%2C220.35 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 218.89..222 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,233.05|127.64,233.05'NetIC41_5' crosses between the drills at (125.1, 233.05) and (127.64, 233.05), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC41_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC41_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 233.05) and (127.64, 233.05), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.37, 233.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC41_5' on TOP_LAYER at (126.37, 233.37), 1.3 mm between the drills at (125.1, 233.05) and (127.64, 233.05) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C233.05%7C127.64%2C233.05 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 231.59..234.7 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,245.75|127.64,245.75'NetIC33_5' crosses between the drills at (125.1, 245.75) and (127.64, 245.75), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC33_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC33_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 245.75) and (127.64, 245.75), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.14, 245.52). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC33_5' on TOP_LAYER at (126.14, 245.52), 1.3 mm between the drills at (125.1, 245.75) and (127.64, 245.75) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C245.75%7C127.64%2C245.75 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 244.29..247.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,258.45|127.64,258.45'NetIC25_5' crosses between the drills at (125.1, 258.45) and (127.64, 258.45), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC25_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC25_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 258.45) and (127.64, 258.45), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.37, 258.77). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC25_5' on TOP_LAYER at (126.37, 258.77), 1.3 mm between the drills at (125.1, 258.45) and (127.64, 258.45) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C258.45%7C127.64%2C258.45 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 256.99..260.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,273.69|127.64,273.69'NetIC17_5' crosses between the drills at (125.1, 273.69) and (127.64, 273.69), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC17_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC17_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 273.69) and (127.64, 273.69), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.37, 274.01). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC17_5' on TOP_LAYER at (126.37, 274.01), 1.3 mm between the drills at (125.1, 273.69) and (127.64, 273.69) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C273.69%7C127.64%2C273.69 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 272.23..275.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,286.39|127.64,286.39'NetIC9_5' crosses between the drills at (125.1, 286.39) and (127.64, 286.39), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC9_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC9_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 286.39) and (127.64, 286.39), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.37, 286.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC9_5' on TOP_LAYER at (126.37, 286.71), 1.3 mm between the drills at (125.1, 286.39) and (127.64, 286.39) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C286.39%7C127.64%2C286.39 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 284.93..288.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:125.1,299.09|127.64,299.09'NetIC1_5' crosses between the drills at (125.1, 299.09) and (127.64, 299.09), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC1_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC1_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (125.1, 299.09) and (127.64, 299.09), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (126.37, 299.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC1_5' on TOP_LAYER at (126.37, 299.41), 1.3 mm between the drills at (125.1, 299.09) and (127.64, 299.09) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A125.1%2C299.09%7C127.64%2C299.09 serves each with its own layer_image region; all of them lie in x 124.91..127.37, y 297.63..300.74 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,203.84|130.18,203.842 nets cross the slot of 3 drills from (127.64, 203.84) to (130.18, 203.84), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 203.84) to (130.18, 203.84), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 203.84), 0.28 mm between the drills at (128.91, 203.84) and (130.18, 203.84) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 203.84), 0.28 mm between the drills at (128.91, 203.84) and (130.18, 203.84) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 203.51), 1.3 mm between the drills at (127.64, 203.84) and (130.18, 203.84) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 203.51), 1.3 mm between the drills at (127.64, 203.84) and (130.18, 203.84) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C203.84%7C130.18%2C203.84 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 202.19..205.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,216.54|130.18,216.542 nets cross the slot of 3 drills from (127.64, 216.54) to (130.18, 216.54), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 216.54) to (130.18, 216.54), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 216.54), 0.28 mm between the drills at (128.91, 216.54) and (130.18, 216.54) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 216.54), 0.28 mm between the drills at (128.91, 216.54) and (130.18, 216.54) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 216.21), 1.3 mm between the drills at (127.64, 216.54) and (130.18, 216.54) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 216.21), 1.3 mm between the drills at (127.64, 216.54) and (130.18, 216.54) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C216.54%7C130.18%2C216.54 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 214.89..218.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,229.24|130.18,229.242 nets cross the slot of 3 drills from (127.64, 229.24) to (130.18, 229.24), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 229.24) to (130.18, 229.24), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 229.24), 0.28 mm between the drills at (128.91, 229.24) and (130.18, 229.24) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 229.24), 0.28 mm between the drills at (128.91, 229.24) and (130.18, 229.24) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 228.91), 1.3 mm between the drills at (127.64, 229.24) and (130.18, 229.24) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 228.91), 1.3 mm between the drills at (127.64, 229.24) and (130.18, 229.24) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C229.24%7C130.18%2C229.24 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 227.59..230.89 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,241.94|130.18,241.942 nets cross the slot of 3 drills from (127.64, 241.94) to (130.18, 241.94), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 241.94) to (130.18, 241.94), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 241.94), 0.28 mm between the drills at (128.91, 241.94) and (130.18, 241.94) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 241.94), 0.28 mm between the drills at (128.91, 241.94) and (130.18, 241.94) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 241.61), 1.3 mm between the drills at (127.64, 241.94) and (130.18, 241.94) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 241.61), 1.3 mm between the drills at (127.64, 241.94) and (130.18, 241.94) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C241.94%7C130.18%2C241.94 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 240.29..243.59 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,254.64|130.18,254.642 nets cross the slot of 3 drills from (127.64, 254.64) to (130.18, 254.64), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 254.64) to (130.18, 254.64), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 254.64), 0.28 mm between the drills at (128.91, 254.64) and (130.18, 254.64) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 254.64), 0.28 mm between the drills at (128.91, 254.64) and (130.18, 254.64) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 254.31), 1.3 mm between the drills at (127.64, 254.64) and (130.18, 254.64) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 254.31), 1.3 mm between the drills at (127.64, 254.64) and (130.18, 254.64) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C254.64%7C130.18%2C254.64 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 252.99..256.29 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,269.88|130.18,269.882 nets cross the slot of 3 drills from (127.64, 269.88) to (130.18, 269.88), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 269.88) to (130.18, 269.88), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 269.88), 0.28 mm between the drills at (128.91, 269.88) and (130.18, 269.88) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 269.88), 0.28 mm between the drills at (128.91, 269.88) and (130.18, 269.88) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 269.55), 1.3 mm between the drills at (127.64, 269.88) and (130.18, 269.88) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 269.55), 1.3 mm between the drills at (127.64, 269.88) and (130.18, 269.88) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C269.88%7C130.18%2C269.88 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 268.23..271.53 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:127.64,282.58|130.18,282.582 nets cross the slot of 3 drills from (127.64, 282.58) to (130.18, 282.58), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_1 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (127.64, 282.58) to (130.18, 282.58), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_1' on L6 at (129.54, 282.58), 0.28 mm between the drills at (128.91, 282.58) and (130.18, 282.58) in L5P; other side: no plane on L7P
      • 'A2B_1' on L6 at (129.54, 282.58), 0.28 mm between the drills at (128.91, 282.58) and (130.18, 282.58) in L7P; other side: no plane on L5P
      • 'RESET_1' on L6 at (128.91, 282.25), 1.3 mm between the drills at (127.64, 282.58) and (130.18, 282.58) in L5P; other side: no plane on L7P
      • 'RESET_1' on L6 at (128.91, 282.25), 1.3 mm between the drills at (127.64, 282.58) and (130.18, 282.58) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A127.64%2C282.58%7C130.18%2C282.58 serves each with its own layer_image region; all of them lie in x 127.91..130.54, y 280.93..284.23 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:135.26,176.53|135.26,177.8'NetIC75_18' crosses between the drills at (135.26, 176.53) and (135.26, 177.8), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: NetIC75_18 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (135.26, 176.53) and (135.26, 177.8), and the clearances run together: the straight line from one drill to the next is bare all the way. 'NetIC75_18' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC75_18' on L3 at (135.26, 177.17), 0.28 mm between the drills at (135.26, 176.53) and (135.26, 177.8) in L2P; other side: no plane on L4P
      • 'NetIC75_18' on L3 at (135.26, 177.17), 0.28 mm between the drills at (135.26, 176.53) and (135.26, 177.8) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A135.26%2C176.53%7C135.26%2C177.8 serves each with its own layer_image region; all of them lie in x 134.12..136.39, y 176.17..178.17 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:137.8,184.15|137.8,185.42'A3_1' crosses between the drills at (137.8, 184.15) and (137.8, 185.42), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: A3_1 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (137.8, 184.15) and (137.8, 185.42), and the clearances run together: the straight line from one drill to the next is bare all the way. 'A3_1' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A3_1' on L3 at (137.8, 184.79), 0.28 mm between the drills at (137.8, 184.15) and (137.8, 185.42) in L2P; other side: no plane on L4P
      • 'A3_1' on L3 at (137.8, 184.79), 0.28 mm between the drills at (137.8, 184.15) and (137.8, 185.42) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A137.8%2C184.15%7C137.8%2C185.42 serves each with its own layer_image region; all of them lie in x 136.66..138.93, y 183.79..185.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:137.8,188.6|137.8,193.684 nets cross the slot of 5 drills from (137.8, 188.6) to (137.8, 193.68), whose anti-pads run together in the +3.3V plane on L4P, between 4 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +3.3V plane on L4P is cleared round a field of 5 drills from (137.8, 188.6) to (137.8, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 4 nets cross between drills of it at 4 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (137.8, 191.77), 0.28 mm between the drills at (137.8, 191.14) and (137.8, 192.41) in L4P; other side: no plane on L2P
      • 'A2B' on L3 at (137.8, 189.23), 0.28 mm between the drills at (137.8, 188.6) and (137.8, 189.87) in L4P; other side: no plane on L2P
      • 'ENB' on L3 at (137.8, 193.04), 0.28 mm between the drills at (137.8, 192.41) and (137.8, 193.68) in L4P; other side: no plane on L2P
      • 'SYNCB' on L3 at (137.8, 190.5), 0.28 mm between the drills at (137.8, 189.87) and (137.8, 191.14) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A137.8%2C188.6%7C137.8%2C193.68 serves each with its own layer_image region; all of them lie in x 136.66..138.93, y 188.23..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:137.8,189.87|137.8,193.683 nets cross the slot of 4 drills from (137.8, 189.87) to (137.8, 193.68), whose anti-pads run together in the +15V plane on L2P, between 3 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P is cleared round a field of 4 drills from (137.8, 189.87) to (137.8, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 3 nets cross between drills of it at 3 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (137.8, 191.77), 0.28 mm between the drills at (137.8, 191.14) and (137.8, 192.41) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (137.8, 193.04), 0.28 mm between the drills at (137.8, 192.41) and (137.8, 193.68) in L2P; other side: no plane on L4P
      • 'SYNCB' on L3 at (137.8, 190.5), 0.28 mm between the drills at (137.8, 189.87) and (137.8, 191.14) in L2P; other side: no plane on L4P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A137.8%2C189.87%7C137.8%2C193.68 serves each with its own layer_image region; all of them lie in x 136.66..138.93, y 189.5..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,201.3|145.42,201.3'NetIC58_10' crosses between the drills at (142.88, 201.3) and (145.42, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC58_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC58_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 201.3) and (145.42, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 200.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC58_10' on TOP_LAYER at (144.15, 200.97), 1.3 mm between the drills at (142.88, 201.3) and (145.42, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C201.3%7C145.42%2C201.3 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,214|145.42,214'NetIC50_10' crosses between the drills at (142.88, 214) and (145.42, 214), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC50_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC50_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 214) and (145.42, 214), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 213.67). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC50_10' on TOP_LAYER at (144.15, 213.67), 1.3 mm between the drills at (142.88, 214) and (145.42, 214) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C214%7C145.42%2C214 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 212.35..215.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,226.7|145.42,226.7'NetIC42_10' crosses between the drills at (142.88, 226.7) and (145.42, 226.7), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC42_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC42_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 226.7) and (145.42, 226.7), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 226.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC42_10' on TOP_LAYER at (144.15, 226.37), 1.3 mm between the drills at (142.88, 226.7) and (145.42, 226.7) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C226.7%7C145.42%2C226.7 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 225.05..228.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,239.4|145.42,239.4'NetIC34_10' crosses between the drills at (142.88, 239.4) and (145.42, 239.4), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC34_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC34_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 239.4) and (145.42, 239.4), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 239.07). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC34_10' on TOP_LAYER at (144.15, 239.07), 1.3 mm between the drills at (142.88, 239.4) and (145.42, 239.4) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C239.4%7C145.42%2C239.4 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 237.75..240.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,252.1|145.42,252.1'NetIC26_10' crosses between the drills at (142.88, 252.1) and (145.42, 252.1), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC26_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC26_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 252.1) and (145.42, 252.1), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 251.77). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC26_10' on TOP_LAYER at (144.15, 251.77), 1.3 mm between the drills at (142.88, 252.1) and (145.42, 252.1) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C252.1%7C145.42%2C252.1 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 250.45..253.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,267.34|145.42,267.34'NetIC18_10' crosses between the drills at (142.88, 267.34) and (145.42, 267.34), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC18_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC18_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 267.34) and (145.42, 267.34), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (143.92, 267.56). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC18_10' on TOP_LAYER at (143.92, 267.56), 1.3 mm between the drills at (142.88, 267.34) and (145.42, 267.34) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C267.34%7C145.42%2C267.34 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 265.69..268.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,280.04|145.42,280.04'NetIC10_10' crosses between the drills at (142.88, 280.04) and (145.42, 280.04), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC10_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC10_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 280.04) and (145.42, 280.04), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 279.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC10_10' on TOP_LAYER at (144.15, 279.71), 1.3 mm between the drills at (142.88, 280.04) and (145.42, 280.04) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C280.04%7C145.42%2C280.04 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 278.39..281.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:142.88,292.74|145.42,292.74'NetIC2_10' crosses between the drills at (142.88, 292.74) and (145.42, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC2_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC2_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (142.88, 292.74) and (145.42, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (144.15, 292.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC2_10' on TOP_LAYER at (144.15, 292.41), 1.3 mm between the drills at (142.88, 292.74) and (145.42, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A142.88%2C292.74%7C145.42%2C292.74 serves each with its own layer_image region; all of them lie in x 142.69..145.15, y 291.09..294.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,184.79|144.15,186.06'A5_1' crosses between the drills at (144.15, 184.79) and (144.15, 186.06), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: A5_1 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (144.15, 184.79) and (144.15, 186.06), and the clearances run together: the straight line from one drill to the next is bare all the way. 'A5_1' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A5_1' on L3 at (144.15, 185.42), 0.28 mm between the drills at (144.15, 184.79) and (144.15, 186.06) in L2P; other side: no plane on L4P
      • 'A5_1' on L3 at (144.15, 185.42), 0.28 mm between the drills at (144.15, 184.79) and (144.15, 186.06) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C184.79%7C144.15%2C186.06 serves each with its own layer_image region; all of them lie in x 143.01..145.28, y 184.42..186.42 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,201.3|146.69,201.3'NetIC58_11' crosses between the drills at (144.15, 201.3) and (146.69, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC58_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC58_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 201.3) and (146.69, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 200.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC58_11' on TOP_LAYER at (145.42, 200.97), 1.3 mm between the drills at (144.15, 201.3) and (146.69, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C201.3%7C146.69%2C201.3 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,207.65|146.69,207.65'NetIC58_6' crosses between the drills at (144.15, 207.65) and (146.69, 207.65), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC58_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC58_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 207.65) and (146.69, 207.65), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 207.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC58_6' on TOP_LAYER at (145.42, 207.97), 1.3 mm between the drills at (144.15, 207.65) and (146.69, 207.65) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C207.65%7C146.69%2C207.65 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 206.19..209.3 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,214|146.69,214'NetIC50_11' crosses between the drills at (144.15, 214) and (146.69, 214), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC50_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC50_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 214) and (146.69, 214), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 213.67). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC50_11' on TOP_LAYER at (145.42, 213.67), 1.3 mm between the drills at (144.15, 214) and (146.69, 214) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C214%7C146.69%2C214 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 212.35..215.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,220.35|146.69,220.35'NetIC50_6' crosses between the drills at (144.15, 220.35) and (146.69, 220.35), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC50_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC50_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 220.35) and (146.69, 220.35), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 220.67). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC50_6' on TOP_LAYER at (145.42, 220.67), 1.3 mm between the drills at (144.15, 220.35) and (146.69, 220.35) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C220.35%7C146.69%2C220.35 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 218.89..222 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,226.7|146.69,226.7'NetIC42_11' crosses between the drills at (144.15, 226.7) and (146.69, 226.7), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC42_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC42_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 226.7) and (146.69, 226.7), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 226.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC42_11' on TOP_LAYER at (145.42, 226.37), 1.3 mm between the drills at (144.15, 226.7) and (146.69, 226.7) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C226.7%7C146.69%2C226.7 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 225.05..228.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,233.05|146.69,233.05'NetIC42_6' crosses between the drills at (144.15, 233.05) and (146.69, 233.05), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC42_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC42_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 233.05) and (146.69, 233.05), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 232.82). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC42_6' on TOP_LAYER at (145.19, 232.82), 1.3 mm between the drills at (144.15, 233.05) and (146.69, 233.05) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C233.05%7C146.69%2C233.05 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 231.59..234.7 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,239.4|146.69,239.4'NetIC34_11' crosses between the drills at (144.15, 239.4) and (146.69, 239.4), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC34_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC34_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 239.4) and (146.69, 239.4), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 239.07). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC34_11' on TOP_LAYER at (145.42, 239.07), 1.3 mm between the drills at (144.15, 239.4) and (146.69, 239.4) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C239.4%7C146.69%2C239.4 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 237.75..240.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,245.75|146.69,245.75'NetIC34_6' crosses between the drills at (144.15, 245.75) and (146.69, 245.75), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC34_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC34_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 245.75) and (146.69, 245.75), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 246.07). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC34_6' on TOP_LAYER at (145.42, 246.07), 1.3 mm between the drills at (144.15, 245.75) and (146.69, 245.75) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C245.75%7C146.69%2C245.75 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 244.29..247.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,252.1|146.69,252.1'NetIC26_11' crosses between the drills at (144.15, 252.1) and (146.69, 252.1), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC26_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC26_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 252.1) and (146.69, 252.1), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 251.77). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC26_11' on TOP_LAYER at (145.42, 251.77), 1.3 mm between the drills at (144.15, 252.1) and (146.69, 252.1) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C252.1%7C146.69%2C252.1 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 250.45..253.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,258.45|146.69,258.45'NetIC26_6' crosses between the drills at (144.15, 258.45) and (146.69, 258.45), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC26_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC26_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 258.45) and (146.69, 258.45), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 258.22). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC26_6' on TOP_LAYER at (145.19, 258.22), 1.3 mm between the drills at (144.15, 258.45) and (146.69, 258.45) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C258.45%7C146.69%2C258.45 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 256.99..260.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,267.34|146.69,267.34'NetIC18_11' crosses between the drills at (144.15, 267.34) and (146.69, 267.34), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC18_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC18_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 267.34) and (146.69, 267.34), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 267.56). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC18_11' on TOP_LAYER at (145.19, 267.56), 1.3 mm between the drills at (144.15, 267.34) and (146.69, 267.34) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C267.34%7C146.69%2C267.34 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 265.69..268.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,273.69|146.69,273.69'NetIC18_6' crosses between the drills at (144.15, 273.69) and (146.69, 273.69), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC18_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC18_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 273.69) and (146.69, 273.69), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 273.46). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC18_6' on TOP_LAYER at (145.19, 273.46), 1.3 mm between the drills at (144.15, 273.69) and (146.69, 273.69) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C273.69%7C146.69%2C273.69 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 272.23..275.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,280.04|146.69,280.04'NetIC10_11' crosses between the drills at (144.15, 280.04) and (146.69, 280.04), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC10_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC10_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 280.04) and (146.69, 280.04), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 279.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC10_11' on TOP_LAYER at (145.42, 279.71), 1.3 mm between the drills at (144.15, 280.04) and (146.69, 280.04) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C280.04%7C146.69%2C280.04 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 278.39..281.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,286.39|146.69,286.39'NetIC10_6' crosses between the drills at (144.15, 286.39) and (146.69, 286.39), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC10_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC10_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 286.39) and (146.69, 286.39), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 286.16). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC10_6' on TOP_LAYER at (145.19, 286.16), 1.3 mm between the drills at (144.15, 286.39) and (146.69, 286.39) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C286.39%7C146.69%2C286.39 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 284.93..288.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,292.74|146.69,292.74'NetIC2_11' crosses between the drills at (144.15, 292.74) and (146.69, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC2_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC2_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 292.74) and (146.69, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.42, 292.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC2_11' on TOP_LAYER at (145.42, 292.41), 1.3 mm between the drills at (144.15, 292.74) and (146.69, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C292.74%7C146.69%2C292.74 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 291.09..294.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:144.15,299.09|146.69,299.09'NetIC2_6' crosses between the drills at (144.15, 299.09) and (146.69, 299.09), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC2_6 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC2_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (144.15, 299.09) and (146.69, 299.09), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (145.19, 298.86). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC2_6' on TOP_LAYER at (145.19, 298.86), 1.3 mm between the drills at (144.15, 299.09) and (146.69, 299.09) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A144.15%2C299.09%7C146.69%2C299.09 serves each with its own layer_image region; all of them lie in x 143.96..146.42, y 297.63..300.74 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,207.65|147.96,207.65'NetIC58_5' crosses between the drills at (145.42, 207.65) and (147.96, 207.65), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC58_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC58_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 207.65) and (147.96, 207.65), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.46, 207.42). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC58_5' on TOP_LAYER at (146.46, 207.42), 1.3 mm between the drills at (145.42, 207.65) and (147.96, 207.65) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C207.65%7C147.96%2C207.65 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 206.19..209.3 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,220.35|147.96,220.35'NetIC50_5' crosses between the drills at (145.42, 220.35) and (147.96, 220.35), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC50_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC50_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 220.35) and (147.96, 220.35), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.46, 220.12). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC50_5' on TOP_LAYER at (146.46, 220.12), 1.3 mm between the drills at (145.42, 220.35) and (147.96, 220.35) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C220.35%7C147.96%2C220.35 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 218.89..222 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,233.05|147.96,233.05'NetIC42_5' crosses between the drills at (145.42, 233.05) and (147.96, 233.05), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC42_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC42_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 233.05) and (147.96, 233.05), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.69, 233.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC42_5' on TOP_LAYER at (146.69, 233.37), 1.3 mm between the drills at (145.42, 233.05) and (147.96, 233.05) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C233.05%7C147.96%2C233.05 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 231.59..234.7 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,245.75|147.96,245.75'NetIC34_5' crosses between the drills at (145.42, 245.75) and (147.96, 245.75), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC34_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC34_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 245.75) and (147.96, 245.75), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.46, 245.52). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC34_5' on TOP_LAYER at (146.46, 245.52), 1.3 mm between the drills at (145.42, 245.75) and (147.96, 245.75) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C245.75%7C147.96%2C245.75 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 244.29..247.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,258.45|147.96,258.45'NetIC26_5' crosses between the drills at (145.42, 258.45) and (147.96, 258.45), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC26_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC26_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 258.45) and (147.96, 258.45), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.69, 258.77). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC26_5' on TOP_LAYER at (146.69, 258.77), 1.3 mm between the drills at (145.42, 258.45) and (147.96, 258.45) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C258.45%7C147.96%2C258.45 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 256.99..260.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,273.69|147.96,273.69'NetIC18_5' crosses between the drills at (145.42, 273.69) and (147.96, 273.69), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC18_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC18_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 273.69) and (147.96, 273.69), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.69, 274.01). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC18_5' on TOP_LAYER at (146.69, 274.01), 1.3 mm between the drills at (145.42, 273.69) and (147.96, 273.69) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C273.69%7C147.96%2C273.69 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 272.23..275.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,286.39|147.96,286.39'NetIC10_5' crosses between the drills at (145.42, 286.39) and (147.96, 286.39), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC10_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC10_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 286.39) and (147.96, 286.39), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.69, 286.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC10_5' on TOP_LAYER at (146.69, 286.71), 1.3 mm between the drills at (145.42, 286.39) and (147.96, 286.39) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C286.39%7C147.96%2C286.39 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 284.93..288.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.42,299.09|147.96,299.09'NetIC2_5' crosses between the drills at (145.42, 299.09) and (147.96, 299.09), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC2_5 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC2_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (145.42, 299.09) and (147.96, 299.09), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (146.69, 299.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC2_5' on TOP_LAYER at (146.69, 299.41), 1.3 mm between the drills at (145.42, 299.09) and (147.96, 299.09) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A145.42%2C299.09%7C147.96%2C299.09 serves each with its own layer_image region; all of them lie in x 145.23..147.69, y 297.63..300.74 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,203.84|150.5,203.842 nets cross the slot of 3 drills from (147.96, 203.84) to (150.5, 203.84), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 203.84) to (150.5, 203.84), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 203.84), 0.28 mm between the drills at (149.23, 203.84) and (150.5, 203.84) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 203.84), 0.28 mm between the drills at (149.23, 203.84) and (150.5, 203.84) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 203.51), 1.3 mm between the drills at (147.96, 203.84) and (150.5, 203.84) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 203.51), 1.3 mm between the drills at (147.96, 203.84) and (150.5, 203.84) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C203.84%7C150.5%2C203.84 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 202.19..205.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,216.54|150.5,216.542 nets cross the slot of 3 drills from (147.96, 216.54) to (150.5, 216.54), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 216.54) to (150.5, 216.54), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 216.54), 0.28 mm between the drills at (149.23, 216.54) and (150.5, 216.54) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 216.54), 0.28 mm between the drills at (149.23, 216.54) and (150.5, 216.54) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 216.21), 1.3 mm between the drills at (147.96, 216.54) and (150.5, 216.54) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 216.21), 1.3 mm between the drills at (147.96, 216.54) and (150.5, 216.54) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C216.54%7C150.5%2C216.54 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 214.89..218.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,229.24|150.5,229.242 nets cross the slot of 3 drills from (147.96, 229.24) to (150.5, 229.24), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 229.24) to (150.5, 229.24), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 229.24), 0.28 mm between the drills at (149.23, 229.24) and (150.5, 229.24) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 229.24), 0.28 mm between the drills at (149.23, 229.24) and (150.5, 229.24) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 228.91), 1.3 mm between the drills at (147.96, 229.24) and (150.5, 229.24) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 228.91), 1.3 mm between the drills at (147.96, 229.24) and (150.5, 229.24) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C229.24%7C150.5%2C229.24 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 227.59..230.89 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,241.94|150.5,241.942 nets cross the slot of 3 drills from (147.96, 241.94) to (150.5, 241.94), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 241.94) to (150.5, 241.94), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 241.94), 0.28 mm between the drills at (149.23, 241.94) and (150.5, 241.94) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 241.94), 0.28 mm between the drills at (149.23, 241.94) and (150.5, 241.94) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 241.61), 1.3 mm between the drills at (147.96, 241.94) and (150.5, 241.94) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 241.61), 1.3 mm between the drills at (147.96, 241.94) and (150.5, 241.94) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C241.94%7C150.5%2C241.94 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 240.29..243.59 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,254.64|150.5,254.642 nets cross the slot of 3 drills from (147.96, 254.64) to (150.5, 254.64), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 254.64) to (150.5, 254.64), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 254.64), 0.28 mm between the drills at (149.23, 254.64) and (150.5, 254.64) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 254.64), 0.28 mm between the drills at (149.23, 254.64) and (150.5, 254.64) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 254.31), 1.3 mm between the drills at (147.96, 254.64) and (150.5, 254.64) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 254.31), 1.3 mm between the drills at (147.96, 254.64) and (150.5, 254.64) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C254.64%7C150.5%2C254.64 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 252.99..256.29 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,269.88|150.5,269.882 nets cross the slot of 3 drills from (147.96, 269.88) to (150.5, 269.88), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 269.88) to (150.5, 269.88), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 269.88), 0.28 mm between the drills at (149.23, 269.88) and (150.5, 269.88) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 269.88), 0.28 mm between the drills at (149.23, 269.88) and (150.5, 269.88) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 269.55), 1.3 mm between the drills at (147.96, 269.88) and (150.5, 269.88) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 269.55), 1.3 mm between the drills at (147.96, 269.88) and (150.5, 269.88) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C269.88%7C150.5%2C269.88 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 268.23..271.53 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:147.96,282.58|150.5,282.582 nets cross the slot of 3 drills from (147.96, 282.58) to (150.5, 282.58), whose anti-pads run together in the GND plane on L5P and the -15V plane on L7P, between 2 pairs of drills (fastest: A2B_2 at 100 ps 10-90 %, ASSUMED)

      The GND plane on L5P and the -15V plane on L7P are cleared round a field of 3 drills from (147.96, 282.58) to (150.5, 282.58), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), 4 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A2B_2' on L6 at (149.86, 282.58), 0.28 mm between the drills at (149.23, 282.58) and (150.5, 282.58) in L5P; other side: no plane on L7P
      • 'A2B_2' on L6 at (149.86, 282.58), 0.28 mm between the drills at (149.23, 282.58) and (150.5, 282.58) in L7P; other side: no plane on L5P
      • 'RESET_2' on L6 at (149.23, 282.25), 1.3 mm between the drills at (147.96, 282.58) and (150.5, 282.58) in L5P; other side: no plane on L7P
      • 'RESET_2' on L6 at (149.23, 282.25), 1.3 mm between the drills at (147.96, 282.58) and (150.5, 282.58) in L7P; other side: no plane on L5P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A147.96%2C282.58%7C150.5%2C282.58 serves each with its own layer_image region; all of them lie in x 148.23..150.86, y 280.93..284.23 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:150.5,188.6|150.5,192.413 nets cross the slot of 4 drills from (150.5, 188.6) to (150.5, 192.41), whose anti-pads run together in the +3.3V plane on L4P, between 3 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +3.3V plane on L4P is cleared round a field of 4 drills from (150.5, 188.6) to (150.5, 192.41), and the clearances run together: the straight line from one drill to the next is bare all the way. 3 nets cross between drills of it at 3 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (150.5, 191.77), 0.28 mm between the drills at (150.5, 191.14) and (150.5, 192.41) in L4P; other side: no plane on L2P
      • 'A2B' on L3 at (150.5, 189.23), 0.28 mm between the drills at (150.5, 188.6) and (150.5, 189.87) in L4P; other side: no plane on L2P
      • 'SYNCB' on L3 at (150.27, 190.09), 1.3 mm between the drills at (150.5, 188.6) and (150.5, 191.14) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A150.5%2C188.6%7C150.5%2C192.41 serves each with its own layer_image region; all of them lie in x 149.04..151.95, y 188.23..192.77 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:150.5,188.6|150.5,193.684 nets cross the slot of 5 drills from (150.5, 188.6) to (150.5, 193.68), whose anti-pads run together in the +15V plane on L2P, between 4 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P is cleared round a field of 5 drills from (150.5, 188.6) to (150.5, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 4 nets cross between drills of it at 4 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (150.5, 191.77), 0.28 mm between the drills at (150.5, 191.14) and (150.5, 192.41) in L2P; other side: no plane on L4P
      • 'A2B' on L3 at (150.5, 189.23), 0.28 mm between the drills at (150.5, 188.6) and (150.5, 189.87) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (150.27, 192.63), 1.3 mm between the drills at (150.5, 191.14) and (150.5, 193.68) in L2P; other side: no plane on L4P
      • 'SYNCB' on L3 at (150.27, 190.09), 1.3 mm between the drills at (150.5, 188.6) and (150.5, 191.14) in L2P; other side: no plane on L4P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A150.5%2C188.6%7C150.5%2C193.68 serves each with its own layer_image region; all of them lie in x 149.04..151.95, y 188.23..193.86 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:158.12,184.15|158.12,185.42'A3_1' crosses between the drills at (158.12, 184.15) and (158.12, 185.42), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: A3_1 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (158.12, 184.15) and (158.12, 185.42), and the clearances run together: the straight line from one drill to the next is bare all the way. 'A3_1' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A3_1' on L3 at (158.12, 184.79), 0.28 mm between the drills at (158.12, 184.15) and (158.12, 185.42) in L2P; other side: no plane on L4P
      • 'A3_1' on L3 at (158.12, 184.79), 0.28 mm between the drills at (158.12, 184.15) and (158.12, 185.42) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A158.12%2C184.15%7C158.12%2C185.42 serves each with its own layer_image region; all of them lie in x 156.98..159.25, y 183.79..185.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:158.12,188.6|158.12,193.684 nets cross the slot of 5 drills from (158.12, 188.6) to (158.12, 193.68), whose anti-pads run together in the +3.3V plane on L4P, between 4 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +3.3V plane on L4P is cleared round a field of 5 drills from (158.12, 188.6) to (158.12, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 4 nets cross between drills of it at 4 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (158.12, 191.77), 0.28 mm between the drills at (158.12, 191.14) and (158.12, 192.41) in L4P; other side: no plane on L2P
      • 'A2B' on L3 at (158.12, 189.23), 0.28 mm between the drills at (158.12, 188.6) and (158.12, 189.87) in L4P; other side: no plane on L2P
      • 'ENB' on L3 at (158.12, 193.04), 0.28 mm between the drills at (158.12, 192.41) and (158.12, 193.68) in L4P; other side: no plane on L2P
      • 'SYNCB' on L3 at (158.12, 190.5), 0.28 mm between the drills at (158.12, 189.87) and (158.12, 191.14) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A158.12%2C188.6%7C158.12%2C193.68 serves each with its own layer_image region; all of them lie in x 156.98..159.25, y 188.23..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:158.12,189.87|158.12,193.683 nets cross the slot of 4 drills from (158.12, 189.87) to (158.12, 193.68), whose anti-pads run together in the +15V plane on L2P, between 3 pairs of drills (fastest: A1B at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P is cleared round a field of 4 drills from (158.12, 189.87) to (158.12, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 3 nets cross between drills of it at 3 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A1B' on L3 at (158.12, 191.77), 0.28 mm between the drills at (158.12, 191.14) and (158.12, 192.41) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (158.12, 193.04), 0.28 mm between the drills at (158.12, 192.41) and (158.12, 193.68) in L2P; other side: no plane on L4P
      • 'SYNCB' on L3 at (158.12, 190.5), 0.28 mm between the drills at (158.12, 189.87) and (158.12, 191.14) in L2P; other side: no plane on L4P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A158.12%2C189.87%7C158.12%2C193.68 serves each with its own layer_image region; all of them lie in x 156.98..159.25, y 189.5..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,201.3|165.74,201.3'NetIC59_10' crosses between the drills at (163.2, 201.3) and (165.74, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC59_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC59_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 201.3) and (165.74, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 200.97). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC59_10' on TOP_LAYER at (164.47, 200.97), 1.3 mm between the drills at (163.2, 201.3) and (165.74, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C201.3%7C165.74%2C201.3 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,214|165.74,214'NetIC51_10' crosses between the drills at (163.2, 214) and (165.74, 214), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC51_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC51_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 214) and (165.74, 214), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 213.67). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC51_10' on TOP_LAYER at (164.47, 213.67), 1.3 mm between the drills at (163.2, 214) and (165.74, 214) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C214%7C165.74%2C214 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 212.35..215.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,226.7|165.74,226.7'NetIC43_10' crosses between the drills at (163.2, 226.7) and (165.74, 226.7), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC43_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC43_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 226.7) and (165.74, 226.7), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 226.37). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC43_10' on TOP_LAYER at (164.47, 226.37), 1.3 mm between the drills at (163.2, 226.7) and (165.74, 226.7) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C226.7%7C165.74%2C226.7 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 225.05..228.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,239.4|165.74,239.4'NetIC35_10' crosses between the drills at (163.2, 239.4) and (165.74, 239.4), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC35_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC35_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 239.4) and (165.74, 239.4), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 239.07). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC35_10' on TOP_LAYER at (164.47, 239.07), 1.3 mm between the drills at (163.2, 239.4) and (165.74, 239.4) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C239.4%7C165.74%2C239.4 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 237.75..240.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,252.1|165.74,252.1'NetIC27_10' crosses between the drills at (163.2, 252.1) and (165.74, 252.1), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC27_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC27_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 252.1) and (165.74, 252.1), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 251.77). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC27_10' on TOP_LAYER at (164.47, 251.77), 1.3 mm between the drills at (163.2, 252.1) and (165.74, 252.1) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C252.1%7C165.74%2C252.1 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 250.45..253.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,267.34|165.74,267.34'NetIC19_10' crosses between the drills at (163.2, 267.34) and (165.74, 267.34), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC19_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC19_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 267.34) and (165.74, 267.34), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.24, 267.56). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC19_10' on TOP_LAYER at (164.24, 267.56), 1.3 mm between the drills at (163.2, 267.34) and (165.74, 267.34) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C267.34%7C165.74%2C267.34 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 265.69..268.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,280.04|165.74,280.04'NetIC11_10' crosses between the drills at (163.2, 280.04) and (165.74, 280.04), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC11_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC11_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 280.04) and (165.74, 280.04), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 279.71). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC11_10' on TOP_LAYER at (164.47, 279.71), 1.3 mm between the drills at (163.2, 280.04) and (165.74, 280.04) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C280.04%7C165.74%2C280.04 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 278.39..281.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:163.2,292.74|165.74,292.74'NetIC3_10' crosses between the drills at (163.2, 292.74) and (165.74, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC3_10 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC3_10' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (163.2, 292.74) and (165.74, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (164.47, 292.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC3_10' on TOP_LAYER at (164.47, 292.41), 1.3 mm between the drills at (163.2, 292.74) and (165.74, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A163.2%2C292.74%7C165.74%2C292.74 serves each with its own layer_image region; all of them lie in x 163.01..165.47, y 291.09..294.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:164.47,184.79|164.47,186.06'A5_1' crosses between the drills at (164.47, 184.79) and (164.47, 186.06), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: A5_1 at 100 ps 10-90 %, ASSUMED)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (164.47, 184.79) and (164.47, 186.06), and the clearances run together: the straight line from one drill to the next is bare all the way. 'A5_1' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'A5_1' on L3 at (164.47, 185.42), 0.28 mm between the drills at (164.47, 184.79) and (164.47, 186.06) in L2P; other side: no plane on L4P
      • 'A5_1' on L3 at (164.47, 185.42), 0.28 mm between the drills at (164.47, 184.79) and (164.47, 186.06) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A164.47%2C184.79%7C164.47%2C186.06 serves each with its own layer_image region; all of them lie in x 163.33..165.6, y 184.42..186.42 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:164.47,201.3|167.01,201.3'NetIC59_11' crosses between the drills at (164.47, 201.3) and (167.01, 201.3), whose anti-pads run together in the +15V plane on L2P (fastest: NetIC59_11 at 100 ps 10-90 %, ASSUMED)

      Along 'NetIC59_11' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (164.47, 201.3) and (167.01, 201.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.3 mm of bare stretch at (165.51, 201.52). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetIC59_11' on TOP_LAYER at (165.51, 201.52), 1.3 mm between the drills at (164.47, 201.3) and (167.01, 201.3) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A164.47%2C201.3%7C167.01%2C201.3 serves each with its own layer_image region; all of them lie in x 164.28..166.74, y 199.65..202.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    All 369 in the full review

  3. PartLifecyclemajorOpen

    SHT25 on IC78: the distributor catalogue reports "Obsolete" for Sensirion AG's SHT25

    SHT25 on IC78: the distributor catalogue reports "Obsolete" for Sensirion AG's SHT25 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/SHT25/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2026-10-31, 15 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.

    At IC78

  4. observationOBS-283minorOpen

    Display shift registers IC166-IC168 run from +5V but their inputs are driven directly by 3.3 V XMEGA pins

    Display shift registers IC166-IC168 (SN74HC595D) run from +5V, but their inputs are driven directly by 3.3 V XMEGA IC75 pins, below the HC595's guaranteed high threshold.

    Where it is

    • IC166-IC168: VCC (pin 16) and SRCLR (pin 10) on +5V, the unregulated TMV 0505EN IC83 output after L2.
    • SER (IC166 pin 14), SRCLK (11), RCLK (12) and OE (13) come straight from IC75 pins 50, 52, 62 and 49; the clock and enable nets are shared with IC167 and IC168.
    • IC75 ATXMEGA128A1U runs from +3.3V (ADP7104 IC84, 1.22 V x (1 + 62k/36k) = 3.32 V).

    The numbers

    QuantityValueSource
    HC595 VIH min at VCC = 4.5 V3.15 V (more at 5 V)SN74HC595D datasheet, p.4
    XMEGA VOH at 2 mA2.4 V guaranteedATXMEGA128A1U datasheet, p.85
    XMEGA VOH unloadedat most its 3.3 V supplystatement

    Why it matters

    Correct operation relies on typical rather than specified thresholds, and gets worse because +5V comes from an unregulated module. The usual fixes are an HCT595 (VIH 2.0 V) or a level translator. Severity minor: the fault is a 3-digit status display, not the measurement path.

  5. observationOBS-284minorOpen

    LD1 (+3.3V) and LD8 (+5V) indicators are reverse-biased past their 5 V rating whenever +15V is up and T6 is off

    LD1 (+3.3V) and LD8 (+5V) are reverse-biased to about 10 V, past their 5 V rating, whenever +15V is up and the shared low-side switch T6 is off.

    The circuit

    ``mermaid flowchart TD P15["+15V"] --> LD10["LD10"] --> R671["R671 2k4"] --> N["NetR655_1<br/>T6 drain"] P33["+3.3V"] --> LD1["LD1"] --> R655["R655 330R"] --> N P5["+5V"] --> LD8["LD8"] --> R656["R656 750R"] --> N N --> T6["T6 2N7002<br/>gate VPOS, IC75 pin 71<br/>R654 100k pull-down"] --> G["GND"] ``

    With T6 off and +15V enabled, +15V pulls NetR655_1 up through LD10 and R671, and the only paths down are LD1 (anode +3.3V) and LD8 (anode +5V) in reverse.

    The numbers

    QuantityValueSource
    LD1 reverse voltageabout 15 - 1.6 - 3.3 = 10 Vderived
    HSMG-C150 reverse voltage rating5 V (at 100 uA)HSMG-C150 datasheet, p.6
    HSMG-C150 typical breakdown9 VHSMG-C150 datasheet, p.7

    LD1 therefore conducts a few hundred microamps in breakdown, limited by R671.

    Why it matters

    This happens in every state where the firmware drives EN15V high but VPOS low (or during programming, when VPOS is pulled low by R654 but EN15V could be left high by the application). The current is small, so the effect is an out-of-rating stress and a faint glow of LD10 rather than immediate damage. A series diode or a separate switch per rail avoids it. Needs a person to confirm the firmware states.

  6. observationOBS-285minorOpen

    R658 (0603, 0.1 W) dissipates about 105-110 mW while the -15V indicator LD9 is lit

    R658 (0603, 0.1 W) dissipates about 105-110 mW whenever the -15V indicator LD9 is lit, at or slightly above its rating.

    Where it is

    ``mermaid flowchart LR P["+3.3V"] --> T7["T7 BSH203 P-channel<br/>gate VNEG, IC75.70<br/>R657 100k to +3.3V"] T7 -- "NetR658_2" --> R658["R658 2k4<br/>0603 0.1 W"] -- "NetLD9_2" --> LD9["LD9 HSMG-C150"] --> N["-15V"] ``

    The numbers

    QuantityValueSource
    -15V rail-1.22 V x (1 + 91/8.2) = -14.76 V (IC85 ADP7182, R561 91k, R562 8k2)netlist; derived
    LD9 forward voltage2.2 V typicalHSMG-C150 datasheet, p.7
    LED current(3.3 + 14.76 - 2.2) / 2400 = 6.6 mAderived
    R658 dissipation6.6 mA squared x 2k4 = 105 mWderived
    R658 dissipation at nominal -15 V108 mWderived
    R658 rating0.1 W (R0603_2K4_1%_0.1W)BOM

    Why it matters

    The resistor runs at or slightly above its rated power continuously whenever the indicator is on, with no derating for ambient temperature. A 1206 part or a larger value (the LED is rated 25 mA, so 3k9 still gives about 4 mA) would restore margin.

  7. observationOBS-288minorOpen

    Switch-matrix control lines from the XMEGA to the 74HC04 buffers have no pull resistors and float while IC75 is in reset or being programmed

    The switch-matrix control lines from the XMEGA IC75 into the 74HC04 buffer tree have no pull resistors, so they float, and the whole matrix's RESET/VL, SYNC, SCLK, enables and addresses are undefined, while IC75 is in reset or being programmed.

    The lines

    Every line has only a test point on it, no resistor:

    IC75 pinNetDrives
    PD3NetIC75_28 (TP5)RESET/VL (pin 23) of all 64 ADG1414, through IC164 pins 1/3/5/9/11/13 and IC165 pins 1/5 (RESET_1..RESET_8)
    PD4 SSNetIC75_29 (TP18)SYNC, through IC155.11
    PD5 MOSINetIC75_30 (TP11)chain DIN, through IC165.9
    PD7 SCKNetIC75_32 (TP20)SCLK, through IC155.9
    PC0-PC2, PE2MAX328 address and enable lines, through IC155

    The XMEGA tri-states its I/O as soon as reset is asserted (ATXMEGA128A1U datasheet, p.30), so during power-up, reset and PDI programming the 74HC04 inputs float.

    Why it matters

    The +15V and -15V rails that power the MAX328 and ADG1414 analog sides stay off in that window, because EN15V is held low by the ADP7104 internal enable pull-down (500 nA, ADP7104 datasheet, p.4), so no switch can connect a signal. What remains:

    • floating CMOS inputs on eleven 74HC04 (extra supply current, possible oscillation);
    • VL applied to unpowered ADG1414 parts.

    Pull-downs on PD3 (switches held reset) and on the enable lines would make the pre-firmware state defined. Minor, and needs a person to judge against the intended power-up sequence.

  8. observationOBS-290minorOpen

    MAX328 address and enable inputs are driven from the always-on 3.3 V logic while the switched +/-15V rails are off

    The 76 MAX328 multiplexers get their A0-A2 and EN inputs from 74HC04 buffers on the always-on +3.3V, while their +/-15V supplies stay off until firmware drives EN15V, so a high input exceeds the (V+ + 2 V) absolute maximum and back-feeds +15V.

    The supplies

    ``mermaid flowchart LR IC84["IC84 ADP7104<br/>EN tied to +5V"] -- "+3.3V, up whenever USB power is present" --> HC["74HC04 IC155-IC163"] EN["IC75 PF1 EN15V<br/>no resistor"] --> IC88["IC88 ADP7104 EN"] -- "+15V" --> MUX["76 x MAX328<br/>V+ / V-"] EN --> IC85["IC85 ADP7182 EN"] -- "-15V" --> MUX HC -- "A0-A2, EN" --> MUX ``

    • Example: IC1 MAX328 pin 13 V+ on +15V, pin 3 V- on -15V, pins 1/16/15 A0-A2 on A0B_1/A1B_1/A2B_1, pin 2 EN on ENB_1. The same pattern holds on all 76.
    • Example buffer: IC157 74HC04, supplied from +3.3V (pin 14), drives A0B_7, A1B_7, A2B_7, ENB_7, SCLKB_7 and SYNCB_7; IC155-IC163 are the same.

    What goes wrong

    Any buffer output that is high while the +/-15V rails are off puts 3.3 V on a MAX328 digital input with V+ at 0 V. That is above the MAX328 digital-input absolute maximum of -2 V to (V+ + 2 V) (MAX328 datasheet, p.2), and the input clamp diodes then back-feed the +15V net from the logic supply.

    The window covers every power-up (the MCU pins float and the buffer outputs are undefined, see the floating control line observation), and any firmware state that sets mux lines before enabling EN15V.

    Why it matters

    The MAX328 is sold as latch-up proof, so the likely effect is an out-of-rating stress and a partly powered +15V net rather than failure. Holding the 74HC04 outputs low until +/-15V is up (pull-downs plus firmware ordering) or gating the buffer supply would avoid it. Needs a person to confirm the firmware sequence.

  9. observationOBS-292minorOpen

    -15V LDO IC85 (ADP7182) has only 22 uF tantalum capacitors at its input and output; the part asks for ESR of 0.2 ohm or less

    The -15V LDO IC85 (ADP7182) has only 22 uF tantalum capacitors, coded 400 mOhm ESR, at its input and output, where the datasheet asks for ESR of 0.2 ohm or less for stability.

    The numbers

    QuantityValueSource
    Input capacitor, NetC11_2 (IC85 pin 2 VIN)C11 only: CTE3528-21_22UF_20V_10%_LESR0400 tantalumnetlist; BOM
    Output capacitor on -15V within 9 mmC12 only, same part, 8.9 mm awaynetlist; ODB placement
    ESR of that part400 mOhm, inferred from the house code; no manufacturer part number on the BOMBOM code
    Nearest ceramic on -15VC180 100 nF at 51.4 mm (then C179 100 nF at 57.1 mm)ODB placement
    ADP7182 capacitor ESR range0.001 to 0.2 ohmADP7182 datasheet, p.5
    ADP7182 recommendationat least 2.2 uF with an ESR of 0.2 ohm or lessADP7182 datasheet, p.23

    Why it matters

    If the fitted tantalums are at their code ESR, the regulator runs outside its stated stability conditions. -15V feeds V- of all 76 MAX328, all 64 ADG1414 and the analog front end, so oscillation would show up as noise on the leakage measurement.

    A 2.2 uF to 4.7 uF X7R ceramic next to IC85 pins 2 and 5 would satisfy the datasheet. The ADP7104 regulators IC84 and IC88 use the same tantalums but their datasheet accepts ESR up to 1 ohm (page 17), so they are not included. Needs a person to confirm the fitted part ESR.

  10. DecapViaFanoutminorOpen

    DecapViaFanout: 8 components×8

    8 checked by the review by Claude walker W4 (Cern session) — 8 different reasons

    At C145, C146, C147, C148, C149, C150, C151, C152

    Each finding, with its own headline
    • C145C145 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C145 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C145.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C145.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C146C146 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C146 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C146.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C146.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C147C147 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C147 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C147.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C147.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C148C148 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C148 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C148.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C148.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C149C149 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C149 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C149.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C149.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C150C150 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C150 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C150.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C150.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C151C151 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C151 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C151.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C151.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C152C152 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C152 on '+3.3V': its rail pad reaches its via over 2.23 mm of track, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C152.2 (rail) runs 2.23 mm along its copper to its nearest via, 1.23 mm past the 1 mm beside the pad: 0.62 nH; C152.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.54 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.55 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  11. ReferencePlaneDiscontinuityminorOpen

    ReferencePlaneDiscontinuity: 18 boards×18

    18 checked by the review by Claude walker W4 (Cern session) — 18 different reasons

    At merged:130.18,292.74|131.45,292.74, merged:132.72,192.41|132.72,193.68, merged:150.5,292.74|151.77,292.74, merged:153.04,192.41|153.04,193.68, merged:170.82,292.74|172.09,292.74, merged:173.36,192.41|173.36,193.68 and 12 more

    Each finding, with its own headline
    • merged:130.18,292.74|131.45,292.74'ENB_1' crosses between the drills at (130.18, 292.74) and (131.45, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_1 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_1' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (130.18, 292.74) and (131.45, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (130.81, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_1' on TOP_LAYER at (130.81, 292.74), 0.28 mm between the drills at (130.18, 292.74) and (131.45, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A130.18%2C292.74%7C131.45%2C292.74 serves each with its own layer_image region; all of them lie in x 129.81..131.81, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:132.72,192.41|132.72,193.68'ENB' crosses between the drills at (132.72, 192.41) and (132.72, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (132.72, 192.41) and (132.72, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (132.72, 193.04), 0.28 mm between the drills at (132.72, 192.41) and (132.72, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (132.72, 193.04), 0.28 mm between the drills at (132.72, 192.41) and (132.72, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A132.72%2C192.41%7C132.72%2C193.68 serves each with its own layer_image region; all of them lie in x 131.58..133.85, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:150.5,292.74|151.77,292.74'ENB_2' crosses between the drills at (150.5, 292.74) and (151.77, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_2 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_2' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (150.5, 292.74) and (151.77, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (151.13, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_2' on TOP_LAYER at (151.13, 292.74), 0.28 mm between the drills at (150.5, 292.74) and (151.77, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A150.5%2C292.74%7C151.77%2C292.74 serves each with its own layer_image region; all of them lie in x 150.13..152.13, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:153.04,192.41|153.04,193.68'ENB' crosses between the drills at (153.04, 192.41) and (153.04, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (153.04, 192.41) and (153.04, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (153.04, 193.04), 0.28 mm between the drills at (153.04, 192.41) and (153.04, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (153.04, 193.04), 0.28 mm between the drills at (153.04, 192.41) and (153.04, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A153.04%2C192.41%7C153.04%2C193.68 serves each with its own layer_image region; all of them lie in x 151.9..154.17, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:170.82,292.74|172.09,292.74'ENB_3' crosses between the drills at (170.82, 292.74) and (172.09, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_3 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_3' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (170.82, 292.74) and (172.09, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (171.45, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_3' on TOP_LAYER at (171.45, 292.74), 0.28 mm between the drills at (170.82, 292.74) and (172.09, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A170.82%2C292.74%7C172.09%2C292.74 serves each with its own layer_image region; all of them lie in x 170.45..172.45, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:173.36,192.41|173.36,193.68'ENB' crosses between the drills at (173.36, 192.41) and (173.36, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (173.36, 192.41) and (173.36, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (173.36, 193.04), 0.28 mm between the drills at (173.36, 192.41) and (173.36, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (173.36, 193.04), 0.28 mm between the drills at (173.36, 192.41) and (173.36, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A173.36%2C192.41%7C173.36%2C193.68 serves each with its own layer_image region; all of them lie in x 172.22..174.49, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:191.14,292.74|192.41,292.74'ENB_4' crosses between the drills at (191.14, 292.74) and (192.41, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_4 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_4' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (191.14, 292.74) and (192.41, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (191.77, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_4' on TOP_LAYER at (191.77, 292.74), 0.28 mm between the drills at (191.14, 292.74) and (192.41, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A191.14%2C292.74%7C192.41%2C292.74 serves each with its own layer_image region; all of them lie in x 190.77..192.77, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:193.68,192.41|193.68,193.68'ENB' crosses between the drills at (193.68, 192.41) and (193.68, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (193.68, 192.41) and (193.68, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (193.68, 193.04), 0.28 mm between the drills at (193.68, 192.41) and (193.68, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (193.68, 193.04), 0.28 mm between the drills at (193.68, 192.41) and (193.68, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A193.68%2C192.41%7C193.68%2C193.68 serves each with its own layer_image region; all of them lie in x 192.54..194.81, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:211.46,292.74|212.73,292.74'ENB_5' crosses between the drills at (211.46, 292.74) and (212.73, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_5 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_5' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (211.46, 292.74) and (212.73, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (212.09, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_5' on TOP_LAYER at (212.09, 292.74), 0.28 mm between the drills at (211.46, 292.74) and (212.73, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A211.46%2C292.74%7C212.73%2C292.74 serves each with its own layer_image region; all of them lie in x 211.09..213.09, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:214,192.41|214,193.68'ENB' crosses between the drills at (214, 192.41) and (214, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (214, 192.41) and (214, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (214, 193.04), 0.28 mm between the drills at (214, 192.41) and (214, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (214, 193.04), 0.28 mm between the drills at (214, 192.41) and (214, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A214%2C192.41%7C214%2C193.68 serves each with its own layer_image region; all of them lie in x 212.86..215.13, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:231.78,292.74|233.05,292.74'ENB_6' crosses between the drills at (231.78, 292.74) and (233.05, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_6 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_6' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (231.78, 292.74) and (233.05, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (232.41, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_6' on TOP_LAYER at (232.41, 292.74), 0.28 mm between the drills at (231.78, 292.74) and (233.05, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A231.78%2C292.74%7C233.05%2C292.74 serves each with its own layer_image region; all of them lie in x 231.41..233.41, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:234.32,192.41|234.32,193.68'ENB' crosses between the drills at (234.32, 192.41) and (234.32, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (234.32, 192.41) and (234.32, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (234.32, 193.04), 0.28 mm between the drills at (234.32, 192.41) and (234.32, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (234.32, 193.04), 0.28 mm between the drills at (234.32, 192.41) and (234.32, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A234.32%2C192.41%7C234.32%2C193.68 serves each with its own layer_image region; all of them lie in x 233.18..235.45, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:252.1,292.74|253.37,292.74'ENB_7' crosses between the drills at (252.1, 292.74) and (253.37, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_7 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_7' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (252.1, 292.74) and (253.37, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (252.73, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_7' on TOP_LAYER at (252.73, 292.74), 0.28 mm between the drills at (252.1, 292.74) and (253.37, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A252.1%2C292.74%7C253.37%2C292.74 serves each with its own layer_image region; all of them lie in x 251.73..253.73, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:254.64,192.41|254.64,193.68'ENB' crosses between the drills at (254.64, 192.41) and (254.64, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (254.64, 192.41) and (254.64, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (254.64, 193.04), 0.28 mm between the drills at (254.64, 192.41) and (254.64, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (254.64, 193.04), 0.28 mm between the drills at (254.64, 192.41) and (254.64, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A254.64%2C192.41%7C254.64%2C193.68 serves each with its own layer_image region; all of them lie in x 253.5..255.77, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:272.42,292.74|273.69,292.74'ENB_8' crosses between the drills at (272.42, 292.74) and (273.69, 292.74), whose anti-pads run together in the +15V plane on L2P (fastest: ENB_8 at 20 ns 10-90 %, suggested by its name)

      Along 'ENB_8' on TOP_LAYER, the +15V plane on L2P is cleared round the drills at (272.42, 292.74) and (273.69, 292.74), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.28 mm of bare stretch at (273.05, 292.74). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB_8' on TOP_LAYER at (273.05, 292.74), 0.28 mm between the drills at (272.42, 292.74) and (273.69, 292.74) in L2P; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A272.42%2C292.74%7C273.69%2C292.74 serves each with its own layer_image region; all of them lie in x 272.05..274.05, y 291.6..293.87 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:274.96,192.41|274.96,193.68'ENB' crosses between the drills at (274.96, 192.41) and (274.96, 193.68), whose anti-pads run together in the +15V plane on L2P and the +3.3V plane on L4P (fastest: ENB at 20 ns 10-90 %, suggested by its name)

      The +15V plane on L2P and the +3.3V plane on L4P are cleared round the drills at (274.96, 192.41) and (274.96, 193.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 'ENB' crosses between drills of it at 1 place(s), 2 crossings counting each plane beside the track, each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'ENB' on L3 at (274.96, 193.04), 0.28 mm between the drills at (274.96, 192.41) and (274.96, 193.68) in L2P; other side: no plane on L4P
      • 'ENB' on L3 at (274.96, 193.04), 0.28 mm between the drills at (274.96, 192.41) and (274.96, 193.68) in L4P; other side: no plane on L2P

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=merged%3A274.96%2C192.41%7C274.96%2C193.68 serves each with its own layer_image region; all of them lie in x 273.82..276.09, y 192.04..194.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:+15V|-15V678 nets change reference between +15V and -15V at 992 vias, none with a reference that continues across (fastest: A0B at 100 ps 10-90 %, ASSUMED)

      At 992 via(s), on 678 net(s), the signal leaves a layer referenced by one of +15V and -15V for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 992 served. Every site is served, so the finding is the lower tier (info). 992 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +15V and -15V are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'NetIC75_31' at (180.34, 158.12), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 234.2 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'SDA3' at (195.9, 149.86), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 233.9 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'SCL3' at (196.53, 149.23), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 229.4 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'SDA4' at (195.9, 147.96), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 229.1 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'SCL4' at (193.04, 148.27), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 227.7 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_59' at (184.15, 144.15), TOP_LAYER -> BOTTOM_LAYER: +15V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 134.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetC211_2' at (187.96, 148.27), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 133.5 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetC210_2' at (189.23, 147.96), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 132.2 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_37' at (180.34, 154.94), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 131.0 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_15' at (186.06, 160.34), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 126.3 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_58' at (183.52, 144.78), TOP_LAYER -> BOTTOM_LAYER: +15V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 126.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_32' at (180.98, 157.48), TOP_LAYER -> L6: +15V on L2P to GND on L5P, -15V on L7P; pure, no reference continues across; stitching served, 125.2 mm of track past the via on L6: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +15V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • and 980 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=refchange%3A%2B15V%7C-15V serves each with its own layer_image region; all of them lie in x 92.93..286.48, y 93.25..302.36 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:+5V|-15V10 nets change reference between +5V and -15V at 16 vias, none with a reference that continues across (fastest: NetIC166_15 at 100 ps 10-90 %, ASSUMED)

      At 16 via(s), on 10 net(s), the signal leaves a layer referenced by one of +5V and -15V for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 16 served. Every site is served, so the finding is the lower tier (info). 16 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +5V and -15V are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'NetIC75_59' at (284.48, 104.78), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 134.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_58' at (275.59, 104.78), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 126.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_60' at (266.7, 104.78), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 114.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC75_61' at (257.81, 104.78), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 102.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC166_7' at (240.67, 111.13), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC166_7' at (248.92, 90.81), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC167_7' at (227.33, 111.13), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC167_7' at (235.59, 90.81), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC168_7' at (214, 111.13), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC168_7' at (222.25, 90.81), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC166_15' at (246.38, 106.05), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • 'NetIC166_15' at (247.02, 113.67), TOP_LAYER -> BOTTOM_LAYER: +5V on L2P to -15V on L7P; pure, no reference continues across; stitching served, 2.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V on L2P is 0.150 mm from UGND on TOP_LAYER and -15V on L7P 0.150 mm from UGND on BOTTOM_LAYER: their own capacitance carries the return. Served.
      • and 4 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/7/reference-planes?group=refchange%3A%2B5V%7C-15V serves each with its own layer_image region; all of them lie in x 212..286.48, y 88.81..115.67 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

Main parts

Part numberMakerDescriptionWhere
292304-14 Pin + 1 Shield USB ReceptacleJ12
2N7002N-CHANNEL MOSFET WITH DIODET6
ADP7182AUJZ-R7-1.22V to -27V, -200mA, Adjustable, Low Noise, Negative Linear RegulatorIC85
ADR440BRZ5V Ultralow Noise, LDO XFET Voltage References with Current Sink and SourceIC74
ATXMEGA128A1U-AU8/16-bit AVR XMEGA A1U Microcontroller, 1.6-3.6V, 128KB + 8KB Flash, 2KB EEPROM, 8KB SRAM, 100-pin TQFP, Industrial Grade (-40°C to 85°C), Pb-FreeIC75
BSH203P-CHANNEL MOSFET WITH DIODET7
FT232RLUSB to serial UART InterfaceIC87
HSMC-C150LED Red 1C 2ALD4
IRLML6402PBFP-CHANNEL MOSFET WITH ZENER DIODET4
ISO7221ADDual Channel Digital IsolatorIC89
MF-PSMF050X-2FuseF1
MTLW-103-07-L-D-250Connector 6 MaleJ8
MTLW-103-07-L-S-2503 Mini Wire-Wrap Contact Strip HeaderST1
SHT25Humidity and Temperature Sensor ICIC78
SSW-104-02-L-SConnector 4 FemaleJ13
TMV 0505ENTRACO, TMV Serie, Single Output DCDC ConverterIC83
TMV 0515DTRACO, TMV Serie, Dual Output DCDC ConverterIC86
USBLC6-2P62 Data-Line Protection, Very Low Capacitance ESD ProtectionIC90
ADP7104ARDZ-R720V, 500mA, Low Noise, CMOS LDO Linear RegulatorIC84, IC88
ESW-106-69-L-DConnector 12 FemaleJ14, J23
3131730000402Jumper 1 PinSW1, SW2, SW3
HSMY-C150LED Yellow 1C 2ALD3, LD6, LD7
SA52-11SRWA7-Segment Red Display Common AnodeDS1, DS2, DS3
SN74HC595D8-Bit Shift Register With 3-State Output RegisterIC166, IC167, IC168
BZV55-B10Zener DiodeD1, D2, D3, D4
MTLW-102-07-L-S-2502 Mini Wire-Wrap Contact Strip HeaderST2, ST3, ST4, ST5, ST6
SKHHDTA010Push-Button Switch SPDTPB1, PB2, PB3, PB4, PB5
1-1337543-0J10, J2, J4, J5, J6, J7
HSMG-C150LED Green 1C 2ALD1, LD10, LD2, LD5, LD8, LD9
ESW-116-69-L-DConnector 32 FemaleJ15, J16, J17, J18, J19, J20, J21, J22
ESW-125-69-L-DConnector 50 FemaleJ24, J25, J26, J27, J28, J29, J30, J31
74HC04DHex InverterIC155, IC156, IC157, IC158, IC159, IC160 and 5 more
ADG1414BRUZ9.5 Ohm ON Resistance, ±15 V/+12 V/±5 V iCMOS, Serially-Controlled Octal SPST SwitchesIC100, IC101, IC102, IC103, IC104, IC105 and 58 more
MAX328EWE+Ultra-Low Leakage Monolithic CMOS Analog MultiplexersIC1, IC10, IC11, IC12, IC13, IC14 and 69 more
742792037InductorL5
HVC0603T1006FETResistor - 1%R528
HVC0603T5004FETResistor - 1%R519
HVC0603T5005FETResistor - 1%R524
LQH32CN100K33LInductor With CoreL1
LQH32CN4R7M33LInductor With CoreL2, L3, L4

About this design

Design
ARRAY SWITCHING MATRIX — OHWR0004 R1
Designed in
Altium Designer
Board
8 copper layers, 220 × 230 mm, 1190 components, 1446 nets
Licence
CERN-OHL-1.2
Source
https://gitlab.com/ohwr/project/array/array-hardware at commit 3ad9dd6a5460
Attribution
CERN Open Hardware Repository, project ohwr/project/array/array-hardware (commit 3ad9dd6a5460d9055e14ee77ac9d389869d6d45e, 2025-04-09). Licence: CERN-OHL-1.2. Source: https://gitlab.com/ohwr/project/array/array-hardware. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)