Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

F WATCH

OHWR0062 · revision R1

F WATCH (OHWR0062 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in KiCad EDA: a 4-layer board of 40 × 40 mm with 116 components and 98 nets, published under CERN-OHL-1.2, GPL-2.0-or-later.

review 82% walked · 12 findings: 7 major · 5 minor (17 items)

Open in the interactive viewerRead the full review

F WATCH (OHWR0062 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 12 findings: 7 major · 5 minor (17 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-354majorOpen

    GPS ON_OFF (and EXT_RST) driven at 3.0 V into a 1.8 V module rated 2.2 V max

    GPS module U6 ON_OFF (pin 26) is driven straight from the 3.0 V MCU U15, above its 2.2 V absolute maximum, and EXT_RST (pin 10) is driven push-pull where the datasheet asks for it to float.

    Where it is

    ``mermaid flowchart LR U3["U3 TPS780180300<br/>VSET on GND, 3.0 V preset"] -- "VCC 3.0 V" --> U15["U15 EFM32<br/>IOVDD pins 8, 26, 55"] U15 -- "PE13 pin 61, GPS_ON_OFF, direct" --> ON["U6 pin 26 ON_OFF<br/>abs max 2.2 V"] U15 -- "PF5 pin 54, GPS_RST, push-pull" --> RST["U6 pin 10 EXT_RST"] U15 -- "GPS_RXD, direct" --> RX["U6 RX"] ``

    Only TX and WAKUP go through the BSS138 shifters Q1/Q2; the three MCU-to-GPS lines are not shifted. Sheet 2 notes next to U3: "VCC = 3V, 150mA".

    Against the M10478-A1 datasheet

    LineBoardDatasheet
    ON_OFF (pin 26)about 3.0 V high, no resistor, divider or transistorON/OFF pin voltage -0.2 to +2.2 V (p.2); host controlled, cannot be left floating (p.5)
    EXT_RST (pin 10)driven push-pull from U15 pin 54leave floating and GND to reset (p.5)
    RXdriven directly at 3.0 Vtolerated, but back-feeds the internal pull-up if driven from a source higher than 1.8 V (p.10)

    Every rising edge on ON_OFF exceeds the absolute maximum by about 0.8 V.

    Fix

    A divider or open-drain drive with a pull-up to +1.8V on ON_OFF, and open-drain drive on EXT_RST.

  2. observationOBS-355majorOpen

    Magnetic buzzer SP1 (12 ohm coil) driven directly from an MCU pin, no transistor or flyback diode

    Magnetic buzzer SP1 (12 ohm coil, 100 mA at 3 V) is driven directly from MCU U15 pin 18 with no transistor or flyback diode, far beyond the pin's 20 mA drive rating.

    Where it is

    Net /MCU_DISPLAY/BUZ connects only U15 pin 18 (PA9) and SP1 pin 1; SP1 pin 2 is on GND. There is no clamp for the coil flyback at turn-off.

    The numbers

    QuantityValueSource
    SP1 SMT-0540-S-R coil resistance12 +/- 2 ohmSMT-0540-S-R datasheet, p.1
    SP1 current draw at rated 3 V100 mASMT-0540-S-R datasheet, p.1
    EFM32 pin source, high drive mode20 mAEFM32GG330 datasheet, p.71
    EFM32 absolute maximum per pin100 mAEFM32GG330 datasheet, p.61

    The pin is loaded far beyond its drive rating, and the coil current is limited only by the pin driver.

    Why it matters

    The transducer datasheet shows a transistor drive circuit. As built, the buzzer will be quiet and the MCU pin and its IOVDD supply are stressed on each drive cycle; a stuck-high pin puts about 3 V across 12 ohm. Fix: NPN or N-MOSFET low-side switch with a diode across the coil.

  3. observationOBS-356majorOpen

    Charger programming resistors R4/R5/R6 (ISET, ILIM, TMR) have no value

    The bq24072 charger's programming resistors R4 (ISET), R5 (ILIM) and R6 (TMR) have no value, so the published files do not say what current the Li-ion cell is charged with, what the USB input is limited to, or how long the safety timer runs.

    Where it is

    ResistorU2 pinSetsValue on schematic, PCB and BOM
    R416 ISET, to GNDfast-charge current"RES"
    R512 ILIM, to GND (EN2=1/EN1=0 mode)input current limit"RES"
    R614 TMR, to GNDsafety timers"RES"

    Sheet 2 gives only the formulas, not the resistances:

    FormulaConstant
    I_CHG = K_ISET / R_ISETK_ISET = 890 A*ohm
    I_IN_MAX = K_ILIM / R_ILIMK_ILIM = 1550 A*ohm
    timerK_TMR = 48 s/kohm

    Why it matters

    The board cannot be built as designed from the published files, and the charge current must suit a small watch cell.

    The GPS matching inductor L1 ("IND", between U6 pins 4 and 6) is also unvalued, with C10/C11 marked NM.

  4. PartLifecyclemajorOpen

    M10478-A1 on U6: the distributor catalogue reports "Obsolete" for Antenova's M10478-A1

    M10478-A1 on U6: the distributor catalogue reports "Obsolete" for Antenova's M10478-A1 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/M10478-A1/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    At U6

  5. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 3 boards×3

    3 checked by the review by Claude walker W4 (Cern session) — 3 different reasons

    At refchange:+VIN|GND, refchange:GND|VCC, void:routed@B.CU|INNER1.CU

    Each finding, with its own headline
    • refchange:+VIN|GND5 nets change reference between +VIN and GND at 5 vias, none with a reference that continues across (fastest: /MCU_DISPLAY/BUZ at 100 ps 10-90 %, ASSUMED)

      At 5 via(s), on 5 net(s), the signal leaves a layer referenced by one of +VIN and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 5 with none. 5 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +VIN and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'BC_PGOOD_N' at (94.55, -112.94), F.CU -> B.CU: GND on INNER2.CU to +VIN on INNER1.CU; pure, no reference continues across; stitching none, 24.8 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +VIN and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C3 (1 uF 0603) 2.6 mm away: 0.58 nH in the 0.480 mm cavity + 0.51 nH ESL + 0.68 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.96 mm depth, ASSUMED): 55.5 ohm at the knee, 111 % of 50 ohm (assumed track impedance). None.
      • 'BC_CHG_N' at (94.61, -111.64), F.CU -> B.CU: GND on INNER2.CU to +VIN on INNER1.CU; pure, no reference continues across; stitching none, 22.7 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +VIN and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C3 (1 uF 0603) 1.6 mm away: 0.48 nH in the 0.480 mm cavity + 0.51 nH ESL + 0.68 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.96 mm depth, ASSUMED): 52.4 ohm at the knee, 105 % of 50 ohm (assumed track impedance). None.
      • 'USB_ID' at (90.94, -93.64), F.CU -> B.CU: GND on INNER2.CU to +VIN on INNER1.CU; pure, no reference continues across; stitching none, 20.3 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +VIN and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/SW_TL' at (90.95, -88.6), F.CU -> B.CU: GND on INNER2.CU to +VIN on INNER1.CU; pure, no reference continues across; stitching none, 17.0 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +VIN and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/BUZ' at (117.04, -104.15), F.CU -> B.CU: GND on INNER2.CU to +VIN on INNER1.CU; pure, no reference continues across; stitching none, 3.6 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +VIN and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=refchange%3A%2BVIN%7CGND serves each with its own layer_image region; all of them lie in x 88.94..119.04, y -114.94..-86.6 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:GND|VCC24 nets change reference between GND and VCC at 33 vias, none with a reference that continues across (fastest: /MCU_DISPLAY/BUZ at 100 ps 10-90 %, ASSUMED)

      At 33 via(s), on 24 net(s), the signal leaves a layer referenced by one of GND and VCC for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 33 with none. 33 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and VCC are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'SCL' at (98.3, -99.16), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 42.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SCL' at (98.62, -101.72), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 42.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SCL' at (103.6, -105.21), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 42.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SCL' at (111.35, -107.65), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 42.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SDA' at (111.96, -106.93), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 22.7 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/SW_TL' at (97.65, -95.7), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 17.0 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C34 (100 nF 0603) 1.7 mm away: 0.50 nH in the 0.480 mm cavity + 0.51 nH ESL + 0.68 nH mounting (pad 0.10 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 0.96 mm depth, ASSUMED): 53.1 ohm at the knee, 106 % of 50 ohm (assumed track impedance). None.
      • '/MCU_DISPLAY/SW_BR' at (112.55, -97.6), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 12.4 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/SW_BR' at (116.43, -102.39), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 12.4 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/SW_BR' at (122.44, -105.41), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 12.4 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'GPS_ON_OFF' at (112.12, -77.24), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 11.8 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SD_CLK' at (96.51, -105.8), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 10.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (1 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SD_CLK' at (98.86, -103.3), F.CU -> B.CU: GND on INNER2.CU to VCC on INNER1.CU; pure, no reference continues across; stitching none, 10.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (1 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VCC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 21 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=refchange%3AGND%7CVCC serves each with its own layer_image region; all of them lie in x 94.51..124.44, y -112.6..-75.24 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@B.CU|INNER1.CUTracks on B.CU and INNER1.CU cross each other at 14 places, each layer the other's reference with its pour cleared round its own tracks, the longest 8.74 mm; 11 run ALONG the cut round another net's track (fastest: /MCU_DISPLAY/LCD_BKL1 at 100 ps 10-90 %, ASSUMED)

      B.CU and INNER1.CU each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 14 place(s) on 20 net(s), 3 of them seen from both tracks (each counted once). 11 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 3.79 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 17 of the 41 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: '/MCU_DISPLAY/LCD_BKL2' on INNER1.CU at (116.51, -93.7), 8.74 mm, running ALONG the bare copper for 3.79 mm, not across it over copper of GND, /MCU_DISPLAY/LCD_EN, /MCU_DISPLAY/LCD_VCC, /MCU_DISPLAY/LCD_DI, /MCU_DISPLAY/LCD_CLK, /MCU_DISPLAY/LCD_CS, Net-(C31-Pad2), not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/LCD_CLK' on B.CU at (115.39, -97.94), 0.52 mm over copper of /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost / '/MCU_DISPLAY/LCD_DI' on B.CU at (115.08, -95.29), 2.05 mm over copper of /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWCLK, not a plane; other side: none: the signal layer is outermost / '/MCU_DISPLAY/LCD_DI' on B.CU at (115.73, -97.59), 0.67 mm over copper of /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost / '/MCU_DISPLAY/LCD_EN' on B.CU at (115.86, -92.83), 2.05 mm over copper of /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost / '/MCU_DISPLAY/SWCLK' on INNER1.CU at (115.13, -92.04), 4.17 mm, running ALONG the bare copper for 1.25 mm, not across it over copper of /MCU_DISPLAY/LCD_DI, /MCU_DISPLAY/LCD_VCC, /MCU_DISPLAY/LCD_EN, not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDIO' on INNER1.CU at (115.57, -91.89), 2.68 mm, running ALONG the bare copper for 2.02 mm, not across it over copper of GND, /MCU_DISPLAY/LCD_EN, /MCU_DISPLAY/LCD_VCC, not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDO' on INNER1.CU at (116.15, -91.89), 5.15 mm, running ALONG the bare copper for 2.24 mm, not across it over copper of /MCU_DISPLAY/LCD_VCC, /MCU_DISPLAY/LCD_EN, GND, /MCU_DISPLAY/LCD_DI, not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU
      • one crossing of two tracks, seen from each: '/MCU_DISPLAY/LCD_BKL1' on B.CU at (107.71, -83.14), 5.03 mm, running ALONG the bare copper for 1.61 mm, not across it over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/LCD_BKL2, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/MCU_DISPLAY/LCD_BKL1' on INNER1.CU at (110.52, -84.52), 0.98 mm over copper of GPS_RXD, GPS_ON_OFF, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/LCD_BKL1' on INNER1.CU at (111.37, -85.38), 0.52 mm over copper of GPS_TXD, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/LCD_BKL2' on B.CU at (108.9, -85.68), 1.68 mm over copper of /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/MCU_DISPLAY/LCD_BKL2' on INNER1.CU at (107.69, -84.29), 4.03 mm, running ALONG the bare copper for 0.79 mm, not across it over copper of /MCU_DISPLAY/LCD_BKL1, GPS_ON_OFF, GPS_RXD, GPS_TXD, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/LCD_BKL2' on INNER1.CU at (115.33, -89.08), 2.71 mm over copper of VM_EN, /MCU_DISPLAY/SW_TR, GPS_WAKUP, /MCU_DISPLAY/LCD_INV, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/LCD_INV' on B.CU at (115.07, -89.83), 2.23 mm over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost / '/MCU_DISPLAY/SWCLK' on INNER1.CU at (113.01, -88.75), 8.67 mm, running ALONG the bare copper for 1.82 mm, not across it over copper of VM_EN, /MCU_DISPLAY/LCD_INV, GPS_WAKUP, /MCU_DISPLAY/SW_TR, Net-(U15-Pad64), GPS_TXD, GPS_RXD, GPS_ON_OFF, /MCU_DISPLAY/LCD_BKL1, /MCU_DISPLAY/LCD_BKL2, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDIO' on INNER1.CU at (110.16, -86.43), 3.42 mm over copper of /MCU_DISPLAY/LCD_BKL2, /MCU_DISPLAY/LCD_BKL1, GPS_ON_OFF, GPS_RXD, GPS_TXD, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDIO' on INNER1.CU at (115.32, -90.08), 2.74 mm over copper of /MCU_DISPLAY/SW_TR, GPS_WAKUP, /MCU_DISPLAY/LCD_INV, VM_EN, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDO' on INNER1.CU at (110.16, -85.92), 3.52 mm over copper of /MCU_DISPLAY/LCD_BKL2, GPS_TXD, GPS_RXD, GPS_ON_OFF, /MCU_DISPLAY/LCD_BKL1, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDO' on INNER1.CU at (115.82, -90.08), 2.77 mm over copper of VM_EN, /MCU_DISPLAY/LCD_INV, GPS_WAKUP, /MCU_DISPLAY/SW_TR, not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SW_TR' on B.CU at (112.83, -88.83), 3.34 mm, running ALONG the bare copper for 1.26 mm, not across it over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/LCD_BKL2, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'GPS_ON_OFF' on B.CU at (110.09, -84.61), 3.12 mm over copper of /MCU_DISPLAY/LCD_BKL1, /MCU_DISPLAY/LCD_BKL2, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWCLK, not a plane; other side: none: the signal layer is outermost / 'GPS_RXD' on B.CU at (110.41, -85.25), 3.22 mm over copper of /MCU_DISPLAY/LCD_BKL2, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/LCD_BKL1, not a plane; other side: none: the signal layer is outermost / 'GPS_TXD' on B.CU at (111.1, -85.65), 3.16 mm over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/LCD_BKL2, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/LCD_BKL1, not a plane; other side: none: the signal layer is outermost / 'GPS_WAKUP' on B.CU at (114.57, -89.33), 2.22 mm over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost / 'VM_EN' on B.CU at (116.07, -90.33), 2.05 mm over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/MCU_DISPLAY/SWCLK' on INNER1.CU at (103.76, -87.17), 5.34 mm, running ALONG the bare copper for 1.18 mm, not across it over copper of VCC, GPS_RST, USB_ID, +5V, /MCU_DISPLAY/SWDO, /MCU_DISPLAY/SWDIO, not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDIO' on B.CU at (104.05, -86.92), 0.87 mm over copper of /MCU_DISPLAY/SWCLK, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/MCU_DISPLAY/SWDIO' on INNER1.CU at (106.86, -85.7), 4.64 mm, running ALONG the bare copper for 1.17 mm, not across it over copper of GND, /MCU_DISPLAY/SWDO, +5V, USB_ID, GPS_RST, not a plane, to the end of the track; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU / '/MCU_DISPLAY/SWDO' on B.CU at (104.9, -86.92), 1.08 mm over copper of /MCU_DISPLAY/SWCLK, /MCU_DISPLAY/SWDIO, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'GPS_TXD' on B.CU at (114.21, -85.29), 0.86 mm over copper of +1.8V, not a plane; other side: none: the signal layer is outermost
      • 'SD_CS_N' on B.CU at (99.81, -105.26), 0.78 mm over copper of Net-(C6-Pad2), not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'SD_MISO' on B.CU at (96.6, -103.9), 0.72 mm over copper of Net-(C6-Pad2), not a plane; other side: none: the signal layer is outermost
      • 'GPS_RXD' on B.CU at (112.15, -83.23), 0.7 mm over copper of +1.8V, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • 'GPS_ON_OFF' on B.CU at (110.83, -82.77), 0.61 mm over copper of +1.8V, not a plane; other side: none: the signal layer is outermost
      • 'Net-(C31-Pad2)' on B.CU at (114.67, -98.65), 0.52 mm over copper of /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost
      • 'SD_MOSI' on B.CU at (101.68, -104.95), 0.51 mm over copper of Net-(C6-Pad2), not a plane; other side: none: the signal layer is outermost
      • 'SD_MOSI' on B.CU at (98.71, -104.95), 0.51 mm over copper of Net-(C6-Pad2), not a plane; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/LCD_CS' on B.CU at (115.13, -98.19), 0.51 mm over copper of /MCU_DISPLAY/LCD_BKL2, not a plane; other side: none: the signal layer is outermost
      • and 2 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=void%3Arouted%40B.CU%7CINNER1.CU serves each with its own layer_image region; all of them lie in x 95.24..117.76, y -106.77..-81.47 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  6. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 4 boards×4

    4 checked by the review by Claude walker W4 (Cern session) — 4 different reasons

    At refchange:+5V|GND, split@INNER1.CU:+5V|+VIN, split@INNER1.CU:+5V|VCC, split@INNER1.CU:+VIN|VCC

    Each finding, with its own headline
    • refchange:+5V|GND6 nets change reference between +5V and GND at 7 vias, none with a reference that continues across (fastest: /MCU_DISPLAY/LCD_BKL1 at 100 ps 10-90 %, ASSUMED)

      At 7 via(s), on 6 net(s), the signal leaves a layer referenced by one of +5V and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 7 with none. 7 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +5V and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'SCL' at (95.4, -93.45), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 42.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'SDA' at (94.67, -93.85), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 22.7 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'USB_ID' at (96.14, -92.84), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 20.3 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/LCD_BKL1' at (104.47, -84.81), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 14.0 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/MCU_DISPLAY/LCD_BKL1' at (99.31, -87.99), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 14.0 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C35 (4.7 uF 0603) 2.7 mm away: 0.59 nH in the 0.480 mm cavity + 0.51 nH ESL + 1.36 nH mounting (pad 0.10 nH (vias beside the pads) + 1 via pair(s) at 3.30 mm pitch, 0.25 mm drill, 0.96 mm to the farther plane): 77.1 ohm at the knee, 154 % of 50 ohm (assumed track impedance). None.
      • 'FG_ALRT_N' at (93.67, -101.62), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 13.4 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'GPS_RST' at (104.62, -83.38), F.CU -> B.CU: GND on INNER2.CU to +5V on INNER1.CU; pure, no reference continues across; stitching none, 5.9 mm of track past the via on B.CU: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=refchange%3A%2B5V%7CGND serves each with its own layer_image region; all of them lie in x 91.67..106.62, y -103.62..-81.38 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INNER1.CU:+5V|+VIN7 nets cross the split between the +5V and +VIN planes on INNER1.CU at 7 places, with no plane on the track's other side (fastest: /MCU_DISPLAY/SW_BL at 100 ps 10-90 %, ASSUMED)

      On INNER1.CU the +5V and +VIN planes part, and 7 nets cross from one to the other at 7 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 7 crossing(s) the track's other neighbour carries a plane, which the return can use there; 7 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/MCU_DISPLAY/SW_BL' on B.CU at (91.4, -103.67), 0.28 mm; other side: none: the signal layer is outermost
      • 'BC_CHG_N' on B.CU at (92.23, -106.19), 0.22 mm; other side: none: the signal layer is outermost
      • 'BC_PGOOD_N' on B.CU at (91.87, -105.83), 0.22 mm; other side: none: the signal layer is outermost
      • 'SCL' on B.CU at (95.09, -89.51), 0.3 mm; other side: none: the signal layer is outermost
      • 'SDA' on B.CU at (94.67, -89.93), 0.3 mm; other side: none: the signal layer is outermost
      • 'USB_DM' on B.CU at (91.4, -94.79), 0.2 mm; other side: none: the signal layer is outermost
      • 'USB_DP' on B.CU at (91.4, -94.43), 0.2 mm; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=split%40INNER1.CU%3A%2B5V%7C%2BVIN serves each with its own layer_image region; all of them lie in x 90.3..96.09, y -107.3..-88.36 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INNER1.CU:+5V|VCC11 nets cross the split between the +5V and VCC planes on INNER1.CU at 12 places, with no plane on the track's other side (fastest: /MCU_DISPLAY/SW_BL at 100 ps 10-90 %, ASSUMED)

      On INNER1.CU the +5V and VCC planes part, and 11 nets cross from one to the other at 12 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 12 crossing(s) the track's other neighbour carries a plane, which the return can use there; 12 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/MCU_DISPLAY/SW_BL' on B.CU at (94.83, -98.25), 0.16 mm; other side: none: the signal layer is outermost
      • 'AC_SDIO' on B.CU at (101.74, -91.14), 0.53 mm; other side: none: the signal layer is outermost
      • 'BC_CHG_N' on B.CU at (94.83, -101.81), 0.23 mm; other side: none: the signal layer is outermost
      • 'BC_PGOOD_N' on B.CU at (94.83, -101.3), 0.23 mm; other side: none: the signal layer is outermost
      • 'FG_ALRT_N' on B.CU at (94.83, -98.99), 0.16 mm; other side: none: the signal layer is outermost
      • 'GPS_RST' on B.CU at (106.4, -84.7), 3.2 mm; other side: none: the signal layer is outermost
      • 'Net-(R21-Pad2)' on B.CU at (101.88, -89.29), 0.16 mm; other side: none: the signal layer is outermost
      • 'Net-(R22-Pad2)' on B.CU at (101.88, -88.85), 0.16 mm; other side: none: the signal layer is outermost
      • 'SD_MISO' on B.CU at (94.81, -103.96), 0.21 mm; other side: none: the signal layer is outermost
      • 'USB_DM' on B.CU at (95.42, -94.79), 0.23 mm; other side: none: the signal layer is outermost
      • 'USB_DM' on B.CU at (97.18, -93.03), 0.22 mm; other side: none: the signal layer is outermost
      • 'USB_ID' on B.CU at (105.91, -85.71), 2.59 mm; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=split%40INNER1.CU%3A%2B5V%7CVCC serves each with its own layer_image region; all of them lie in x 93.75..107.4, y -105.01..-82.99 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@INNER1.CU:+VIN|VCC6 nets cross the split between the +VIN and VCC planes on INNER1.CU at 8 places, with no plane on the track's other side (fastest: /MCU_DISPLAY/SW_BR at 100 ps 10-90 %, ASSUMED)

      On INNER1.CU the +VIN and VCC planes part, and 6 nets cross from one to the other at 8 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 8 crossing(s) the track's other neighbour carries a plane, which the return can use there; 8 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/MCU_DISPLAY/LCD_CS' on B.CU at (119.37, -98.92), 0.23 mm; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/LCD_CS' on B.CU at (122.03, -96.26), 0.22 mm; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/MCU_RST_N' on B.CU at (112.75, -110.34), 0.18 mm; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/SW_BR' on B.CU at (117.27, -102.94), 0.16 mm; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/SW_BR' on B.CU at (120.32, -103.29), 0.16 mm; other side: none: the signal layer is outermost
      • '/MCU_DISPLAY/SW_TL' on B.CU at (89.73, -87.05), 0.22 mm; other side: none: the signal layer is outermost
      • 'SCL' on B.CU at (95.09, -85.04), 0.18 mm; other side: none: the signal layer is outermost
      • 'SDA' on B.CU at (94.67, -85.02), 0.16 mm; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=split%40INNER1.CU%3A%2BVIN%7CVCC serves each with its own layer_image region; all of them lie in x 88.73..123.03, y -111.45..-83.94 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  7. FiducialMissingmajorOpen

    The top side carries 6 SMT component(s) and no fiducial was found on it

    The top side carries 6 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

    At top

  8. observationOBS-357minorOpen

    No battery temperature sensing: charger TS and fuel-gauge AIN on fixed resistors

    Neither the charger nor the fuel gauge sees the battery temperature: bq24072 TS and MAX17047 AIN sit on fixed resistors, so the Li-ion cell is charged without temperature qualification.

    Where it is

    • Charger U2 bq24072: TS (pin 1) is tied to GND through R27 10k.
    • Fuel gauge U4 MAX17047: the thermistor input AIN (pin 2) sits on a fixed 10k/10k divider: U4 pin 9 THRM - R8 10k - AIN - R28 10k - battery negative (CSP), with C7 on AIN.

    Why it matters

    The datasheet allows a fixed 10k on TS when the function is not used, so this is a design choice. But for a cell worn on the wrist and charged unattended, the missing hot/cold charge cut-off deserves a deliberate decision.

  9. observationOBS-358minorOpen

    No fiducials; title blocks undated with mixed revisions

    The board has no fiducials, and its schematic title blocks are undated with mixed revisions.

    • Fiducials: none on either side, while the board carries 0.5 mm pitch QFN/LFCSP/LGA parts (EFM32 QFN64, ADP198, LSM303C). Assembly of the fine-pitch parts relies on board-edge registration.
    • Title blocks: sheet 1 says "Rev: v2", sheets 2-4 say "Rev: v1", and "Date:" is empty on all four. The design files are named freewatch_v1. The revision marking does not say which release the drawing is.
  10. observationOBS-359minorOpen

    GPS 1PPS not connected: GPS_PPS label on the MCU sheet goes nowhere, U6 TM pin open

    The GPS 1PPS is never wired: the GPS_PPS label on the MCU sheet goes nowhere and U6 pin 11 (TM) is open, so the watch cannot discipline its clock to GPS time in hardware.

    • Sheet 3 (MCU & Display) carries a global label GPS_PPS, drawn near C36, that is attached to no wire or pin.
    • No GPS_PPS label exists on sheet 4.
    • U6 pin 11 (TM, 1PPS time mark) is on a single-pin net, Net-(U6-Pad11).
    • Six MCU pins are free: PA4, PA5, PE8, PE9, PE10, PA15.

    The intent to bring the GPS 1PPS to the MCU is visible but was never wired.

  11. ReferencePlaneDiscontinuityminorOpen

    '/MCU_DISPLAY/SWDIO' crosses where the GND plane on B.CU is drawn back round copper of Net-(U15-Pad64), at 1 place, the longest 0.61 mm (fastest: /MCU_DISPLAY/SWDIO at 100 ps 10-90 %, ASSUMED)

    Along '/MCU_DISPLAY/SWDIO' on INNER1.CU, the GND plane on B.CU has 0.61 mm under the track with copper of Net-(U15-Pad64), not a plane, at (111.63, -87.9), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 86.8..125.8, y -93.01..-74.8 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

    • '/MCU_DISPLAY/SWDIO' on INNER1.CU at (111.63, -87.9), 0.61 mm over copper of Net-(U15-Pad64), not a plane; other side: GND on INNER2.CU, 0.48 mm from the track against 0.48 mm to B.CU: 50% of the return on B.CU

    Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/63/reference-planes?group=void%3AGND%40B.CU%3Acopper%20of%20Net-%28U15-Pad64%29 serves each with its own layer_image region; all of them lie in x 110.28..112.71, y -88.98..-86.55 mm (board frame, Y up).

    Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    At void:GND@B.CU:copper of Net-(U15-Pad64)

  12. DecapViaFanoutminorOpen

    C38 on 'VCC': its rail pad reaches its via over 2.14 mm of track, adding about 0.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

    C38 on 'VCC': its rail pad reaches its via over 2.14 mm of track, adding about 0.56 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C38.1 (rail) runs 2.14 mm along its copper to its nearest via, 1.14 mm past the 1 mm beside the pad: 0.56 nH; C38.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.51 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.56 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.19 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.96 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    At C38

Main parts

Part numberMakerDescriptionWhere
bq24072Li-ion charger with power-path (TI BQ24072, RGT QFN-16)U2
CDBU0130RD3
EFM32GG330EFM32 Giant Gecko MCU, QFN64U15
LS013B7DH03Sharp 1.28 in memory LCD 128x128 on FPC connector (Molex 503480-1000 footprint)U14
LSM303C3D accelerometer and magnetometer, 3-wire SPIU11
M10478-A1GPS module with antenna, SiRFstarIV (Antenova M10478-A1)U6
MAX170471-cell fuel gauge (Maxim MAX17047, TDFN-10)U4
MAX44009ambient light sensor, I2C 0x4AU10
MS5806-02BAbarometric pressure sensor, I2C 0x77 (CSB low)U12
PRTR5V0U2XUSB ESD protectionU1
SMT-0540-S-RPUI Audio magnetic transducer, 3 V, 12 ohm coil (footprint BUZZER_SMT-0540-S-R)SP1
SST25WF040B4 Mbit 1.8 V SPI flash for the GPSU9
ADP1981 A high-side load switch, vibration motor supplyU13, U8
BSS138Q1, Q2
TPS780180300LDO 1.8/3.0 V selectable, 150 mA; VSET low = 3.0 V (VCC)U3, U5
EVQ-P4MB3KSW1, SW2, SW3, SW4

About this design

Design
F WATCH — OHWR0062 R1
Designed in
KiCad EDA
Board
4 copper layers, 40 × 40 mm, 116 components, 98 nets
Licence
CERN-OHL-1.2, GPL-2.0-or-later
Source
https://gitlab.com/ohwr/project/f-watch at commit 102fcc56ed22
Attribution
CERN Open Hardware Repository, project ohwr/project/f-watch (commit 102fcc56ed2237c1340b527cdd4478025e4ad4a3, 2025-04-09). Licence: CERN-OHL-1.2, GPL-2.0-or-later. Source: https://gitlab.com/ohwr/project/f-watch. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)