Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

FMC PROFINET JTAG BREAKOUT

OHWR0052 · revision R1

FMC PROFINET JTAG BREAKOUT (OHWR0052 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 2-layer board of 39 × 38 mm with 4 components and 10 nets, published under CERN-OHL-W-2.0.

review 97% walked · 3 findings: 1 major · 2 minor

Open in the interactive viewerRead the full review

FMC PROFINET JTAG BREAKOUT (OHWR0052 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 3 findings: 1 major · 2 minor on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-198majorOpen

    R2 is 1k on the schematic but ordered as the 10k part: built by part number, nTRST sits at mid-rail against the 10k pull-down on the FMC Profinet board

    R2 is 1k on the schematic but its BOM part number is the 10k part (R0805_10K_1%_0.125W_100PPM); built by part number, HDR_nTRST sits at 1.65 V, in the undefined band of a 3.3 V input, so the debug logic may stay in reset or toggle with noise.

    Where it is

    • The BOM row for R2 gives the value 1k but the part number R0805_10K_1%_0.125W_100PPM, the same 10k part as R1. The LibRef was not changed when the value was edited.
    • R2 pulls HDR_nTRST (J1.3, J2.14) up to P3V3.
    • Sheet note #1: HDR_nTRST "is connected with 10k Pull-down on FMC Profinet, strong pull-up R2 (1k) here is enough to enable the debug logic when plugged in".

    The numbers

    R2 fittedHDR_nTRST levelSource
    1k, as intendedabout 3.0 V, logic highderived: 3.3 × 10/(10+1)
    10k, as ordered3.3 × 10/(10+10) = 1.65 V, undefined bandderived
  2. observationOBS-199minorOpen

    Title block leaves revision, document number, sheet number and checker as '*' placeholders

    The title block of the only schematic sheet leaves Rev, Document, Drawn by, Check.by and the sheet number as "*" template placeholders; the design version exists only inside the project title text (V2.0).

    FieldValue
    Project/Equipment"JTAG Breakout Board for FMC Profinet V2.0"
    Designerfilled
    Filefilled
    Rev"*"
    Document"*"
    Drawn by"*"
    Check.by"*"
    Sheet"Sheet * of 1"

    No revision is stated in the revision field.

  3. FiducialMissingminorOpen

    The top side carries 2 SMT component(s) and no fiducial was found on it

    The top side carries 2 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release. Graded minor: the side carries only 2 SMT part(s) (at most 5), which a placement machine can usually align on their own pads; a fine-pitch part among them would still want one.

    At top

Main parts

Part numberMakerDescriptionWhere
87833-1420MOLEXConnector 14 MaleJ2
N2520-6002RB3MConnector 20 MaleJ1
R0805_10K_1%_0.125W_100PPMGENERICResistor - 1%R1, R2

About this design

Design
FMC PROFINET JTAG BREAKOUT — OHWR0052 R1
Designed in
Altium Designer
Board
2 copper layers, 39 × 38 mm, 4 components, 10 nets
Licence
CERN-OHL-W-2.0
Source
https://gitlab.com/ohwr/project/fmc-profinet at commit 54c1b43fddf9
Attribution
CERN Open Hardware Repository, project ohwr/project/fmc-profinet (commit 54c1b43fddf994704061cdc9ba3c4c7f1677d31a, 2025-04-10). Licence: CERN-OHL-W-2.0. Source: https://gitlab.com/ohwr/project/fmc-profinet. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)