Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

FMC TDC 1NS 5CHA

OHWR0033 · revision R1

FMC TDC 1NS 5CHA (OHWR0033 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 6-layer board of 76.5 × 69 mm with 217 components and 200 nets, published under CERN-OHL-1.1.

review 80% walked · 18 findings: 8 major · 10 minor (49 items)

Open in the interactive viewerRead the full review

FMC TDC 1NS 5CHA (OHWR0033 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 18 findings: 8 major · 10 minor (49 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-189majorOpen

    TDC-GPX core rails come from P12V0 with no clamp to Vddo, so Vddc can exceed Vddo + 0.6 V at power-up

    The TDC-GPX (IC8) core rails VDDC_TDC and VDDC2_TDC come from P12V0 with no Schottky clamp to Vddo (P3V3), so Vddc can exceed the Vddo + 0.6 V absolute maximum at power-up.

    Where it is

    ``mermaid flowchart LR P12["FMC P12V0"] --> IC12["IC12 LM1117-ADJ"] --> V1["VDDC_TDC"] P12 --> IC11["IC11 LM1117-ADJ"] --> V2["VDDC2_TDC"] P33["FMC P3V3 = Vddo"] --> IC8["IC8 TDC-GPX I/O"] V1 --> IC8 V2 --> IC8 ``

    • VDDC_TDC and VDDC2_TDC are the TDC-GPX core, hardmacro and oscillator supplies.
    • No diode connects VDDC_TDC or VDDC2_TDC to P3V3. The only diodes on the board are the BZV55 zener D1, the input clamp arrays D1A-E/D2A-E and BAR66 D7 on the supervisor reset timing.

    What the datasheet requires

    QuantityValueSource
    Vddc absolute maximumVddc < Vddo + 0.6 VTDC-GPX datasheet, p.7
    Recommended regulation circuit (Figure 15)BAT47 Schottky from Vddo to VddcTDC-GPX datasheet, p.16

    Why it matters

    On a carrier that brings up 12 V before 3.3 V, or when 3.3 V is absent, the core rails reach their regulated value with Vddo at 0 V. An absolute maximum violation on every power cycle then depends on carrier rail ordering, which the mezzanine does not control. A Schottky from P3V3 to each Vddc rail, as in the datasheet reference circuit, removes the dependency.

  2. observationOBS-190majorOpen

    A 5 V input pulse drives the CDCLVC1102 inputs above VDD + 0.5 V: the only clamp is a BAR66 to P3V3 behind 33 ohm

    A 5 V input pulse, the designer's stated level, drives each CDCLVC1102 input (IC1A-E pin 1) to about 4.1-4.2 V, above its VDD + 0.5 V = 3.8 V absolute maximum; the only clamp is a BAR66 to P3V3 behind 33 ohm.

    The input chain, every channel

    ``mermaid flowchart LR J["J1-J5 input"] --> F["F1x polyfuse"] --> N1["D1x BAR66<br/>clamp to P5V0"] N1 --> R10["R10x 33 ohm"] --> N2["NetD2x_3<br/>D2x BAR66 clamp to P3V3<br/>R11x 4k12 to GND"] N2 --> IC["IC1x CDCLVC1102<br/>input pin 1"] ``

    The sheet 4 note sizes the termination for 5 V at the input ("termination resistor power dissipation: 5V*5V/50Ohm=0.5W using 3 x 150R"), so 5 V at the fuse output is a normal operating level.

    The numbers

    QuantityValueSource
    Input level5 Vschematic sheet 4 note
    P5V0 rail5.1 V, so D1x does not conductstatement
    Current through R10x into D2x and P3V3about 30 mA per channel, for as long as the pulse lastsderived
    BAR66 forward drop0.95 V typical at 50 mABAR66 datasheet, p.2
    Buffer input voltage3.3 V + BAR66 drop = about 4.1-4.2 Vderived
    CDCLVC1102 absolute max inputVDD + 0.5 V = 3.8 VCDCLVC1102 datasheet, p.5
    CDCLVC1102 input current rating20 mACDCLVC1102 datasheet, p.5

    The buffer's own input clamp shares that current, against its 20 mA input-current rating.

    Why it matters

    The level is the designer's stated input amplitude, not an ESD transient, so the absolute maximum applies. A Schottky clamp, a larger series resistor, or a divider ahead of the 3.3 V buffer would hold the pin inside VDD + 0.5 V.

  3. observationOBS-532majorOpen

    LM1117-ADJ regulators IC11 and IC12 have output ESR below the 0.3 Ω minimum the datasheet requires

    IC11 and IC12 (LM1117-ADJ) are loaded with parallel low-ESR tantalums whose combined ESR is about 0.06-0.13 Ω, below the 0.3-22 Ω window TI requires for LM1117 stability. The regulators may ring or oscillate, especially cold or at light load.

    The requirement

    ItemValueSource
    Minimum output capacitance (tantalum)10 µF; 22 µF when the ADJ pin is bypassedLM1117 datasheet p.15, 9.2.2.1.3
    Output capacitor ESR0.3 Ω to 22 Ωsame

    What the board fits

    RegulatorOutput netOutput capacitorsESR eachCombined ESR
    IC11VDDC2_TDCC17, C27: 47 µF 6.3 V tantalum 'CTE3528-21_47UF_6.3V_10%_LESR0250', plus C58, C59 100 nF X7R0.25 Ω (from the part code)about 0.125 Ω
    IC12VDDC_TDCC13, C16, C19, C21: same 47 µF part, plus four 100 nF X7R0.25 Ωabout 0.06 Ω

    Both ADJ pins are bypassed (C22 / C28, 10 µF), so the 22 µF minimum applies. Capacitance is met (94 µF and 188 µF); ESR is not. The parallel ceramics lower it further at high frequency.

    Why it matters

    The LM1117's loop relies on the output capacitor's ESR zero for phase margin. Below 0.3 Ω that zero moves past crossover and phase margin falls. Single-capacitor outputs with a 0.3-1 Ω tantalum, or an LDO specified for low-ESR ceramics, meet the datasheet.

    A working board in the field shows margin under its conditions, not across temperature and load. Worth a bring-up check of VDDC_TDC and VDDC2_TDC ringing on a load step.

  4. PartLifecyclemajorOpen

    BAR66 on 6 placements (D2A, D2B, D2C, D2D, D2E, D7): the distributor catalogue reports "Obsolete" for Infineon Technologies's BAR66

    BAR66 on 6 placements (D2A, D2B, D2C, D2D, D2E, D7): the distributor catalogue reports "Obsolete" for Infineon Technologies's BAR66 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (INFINEON). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/BAR66/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    At D2A

  5. DecapViaFanoutmajorOpen

    DecapViaFanout: 2 components×2

    Checked by the review, stands · Claude walker W3 (Cern session) — Checked: the fan-out length is read from the copper as stated. The 0.5 nH limit is Probe's starting value, not a datasheet or vendor requirement on file; whether it matters depends on this capacitor's role in the rail's PDN target. Left for the owner.

    At C47, C48

    Each finding, with its own headline
    • C47C47 on 'P3V3_PLL': its rail pad reaches its via over 2.27 mm of track and its ground pad over 1.37 mm, adding about 0.83 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C47 on 'P3V3_PLL': its rail pad reaches its via over 2.27 mm of track and its ground pad over 1.37 mm, adding about 0.83 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C47.2 (rail) runs 2.27 mm along its copper to its nearest via, 1.27 mm past the 1 mm beside the pad: 0.64 nH; C47.1 (ground) runs 1.37 mm along its copper to its nearest via, 0.37 mm past the 1 mm beside the pad: 0.19 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.83 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.48 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.45 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C48C48 on 'P3V3': its rail pad reaches its via over 0.00 mm of track and its ground pad over 3.63 mm, adding about 1.33 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C48 on 'P3V3': its rail pad reaches its via over 0.00 mm of track and its ground pad over 3.63 mm, adding about 1.33 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C48.1 (rail) runs 0.00 mm along its copper to its nearest via, beside the pad; C48.2 (ground) runs 3.63 mm along its copper to its nearest via, 2.63 mm past the 1 mm beside the pad: 1.33 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.33 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  6. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 12 boards×12

    Checked by the review, stands · Claude walker W3 (Cern session) — Checked: the reference break is read from the copper as stated. Whether it matters depends on the signal's edge rate and the receiver's margin, which no datasheet or app note on file fixes for this net; the impedance step and reflection figures are Probe's model, and the thresholds are its starting values. Layout practice, not a datasheet requirement. Left for the owner.

    At along@PWR_PLANE:P3V3|P3V3_PLL, merged:145.07,122.14|147.61,124.68, merged:145.07,125.95|147.61,128.49, merged:145.07,129.76|146.34,129.76, merged:145.07,133.57|146.34,137.38, merged:145.07,133.57|146.34,138.65 and 6 more

    Each finding, with its own headline
    • along@PWR_PLANE:P3V3|P3V3_PLL2 nets run ALONG the split between the P3V3 and P3V3_PLL planes on PWR_PLANE at 3 places, the longest 10.48 mm; the impedance rises from 81 ohm to 82 ohm there at worst, 0.5 % of each edge reflected (fastest: CP at 100 ps 10-90 %, ASSUMED)

      On PWR_PLANE the P3V3 and P3V3_PLL planes part, and 2 nets run down the slot between them at 3 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 81 ohm; along the slot 82 ohm, reflecting up to 0.5 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 89 ohm). At 2 place(s) the impedance cannot be said: the track's centreline is not over the slot. At 1 of the 3 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'PLL_SDI' on SIGNAL_INT1 at (129.4, 131.45), 3.27 mm, running ALONG the split for 2.82 mm, not across it, impedance not said: the track's centreline is not over the slot; other side: no plane on SIGNAL_INT2
      • 'CP' on TOP_LAYER at (119.07, 137.48), 1.9 mm, running ALONG the split for 1.91 mm, not across it, impedance not said: the track's centreline is not over the slot; other side: none: the signal layer is outermost
      • 'PLL_SDI' on SIGNAL_INT1 at (116.36, 135.1), 10.48 mm, running ALONG the split for 10.48 mm, not across it, 81 ohm over solid plane, 82 ohm along it: 0.5 % of each edge reflected; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=along%40PWR_PLANE%3AP3V3%7CP3V3_PLL serves each with its own layer_image region; all of them lie in x 110.13..131.81, y 130.45..138.8 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.07,122.14|147.61,124.682 nets cross the slot of 7 drills from (145.07, 122.14) to (147.61, 124.68), whose anti-pads run together in the P3V3 plane on PWR_PLANE, between 2 pairs of drills (fastest: PLL_SDO at 100 ps 10-90 %, ASSUMED)

      The P3V3 plane on PWR_PLANE is cleared round a field of 7 drills from (145.07, 122.14) to (147.61, 124.68), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PLL_CSN' on SIGNAL_INT1 at (146.97, 123.98), 1.74 mm between the drills at (147.61, 123.41) and (147.61, 124.68) in PWR_PLANE; other side: no plane on SIGNAL_INT2
      • 'PLL_SDO' on SIGNAL_INT1 at (145.7, 122.77), 1.74 mm between the drills at (145.07, 122.14) and (145.07, 123.41) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C122.14%7C147.61%2C124.68 serves each with its own layer_image region; all of them lie in x 143.84..148.84, y 121.77..124.98 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.07,125.95|147.61,128.492 nets cross the slot of 5 drills from (145.07, 125.95) to (147.61, 128.49), whose anti-pads run together in the P3V3 plane on PWR_PLANE, between 2 pairs of drills (fastest: PLL_SDI at 100 ps 10-90 %, ASSUMED)

      The P3V3 plane on PWR_PLANE is cleared round a field of 5 drills from (145.07, 125.95) to (147.61, 128.49), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PLL_SDI' on SIGNAL_INT1 at (145.07, 126.52), 0.47 mm between the drills at (145.07, 125.95) and (145.07, 127.22) in PWR_PLANE; other side: no plane on SIGNAL_INT2
      • 'SCL' on SIGNAL_INT1 at (147.61, 127.85), 0.47 mm between the drills at (147.61, 127.22) and (147.61, 128.49) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C125.95%7C147.61%2C128.49 serves each with its own layer_image region; all of them lie in x 143.84..148.84, y 125.52..128.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.07,129.76|146.34,129.76'PLL_STATUS' crosses between the drills at (145.07, 129.76) and (145.07, 131.03), whose anti-pads run together in the P3V3 plane on PWR_PLANE (fastest: PLL_STATUS at 100 ps 10-90 %, ASSUMED)

      Along 'PLL_STATUS' on SIGNAL_INT1, the P3V3 plane on PWR_PLANE is cleared round the drills at (145.07, 129.76) and (145.07, 131.03), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.47 mm of bare stretch at (145.07, 130.39). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PLL_STATUS' on SIGNAL_INT1 at (145.07, 130.39), 0.47 mm between the drills at (145.07, 129.76) and (145.07, 131.03) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C129.76%7C146.34%2C129.76 serves each with its own layer_image region; all of them lie in x 143.84..146.3, y 129.39..131.39 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.07,133.57|146.34,137.382 nets cross between the drills at (146.34, 136.11) and (146.34, 137.38), whose anti-pads run together in the GND plane on GND_PLANE (fastest: LED_TRIG_3 at 100 ps 10-90 %, ASSUMED)

      The GND plane on GND_PLANE is cleared round a field of 6 drills from (145.07, 133.57) to (146.34, 137.38), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LED_TRIG_3' on BOTTOM_LAYER at (146.14, 136.74), 1.47 mm between the drills at (146.34, 136.11) and (146.34, 137.38) in GND_PLANE; other side: none: the signal layer is outermost
      • 'RESETN' on SIGNAL_INT2 at (145.7, 136.78), 1.74 mm between the drills at (146.34, 136.11) and (146.34, 137.38) in GND_PLANE; other side: no plane on SIGNAL_INT1

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C133.57%7C146.34%2C137.38 serves each with its own layer_image region; all of them lie in x 143.84..147.57, y 135.74..138.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:145.07,133.57|146.34,138.65'PLL_DAC_SYNCN' crosses between the drills at (145.07, 134.84) and (145.07, 136.11), whose anti-pads run together in the P3V3 plane on PWR_PLANE (fastest: PLL_DAC_SYNCN at 100 ps 10-90 %, ASSUMED)

      Along 'PLL_DAC_SYNCN' on SIGNAL_INT1, the P3V3 plane on PWR_PLANE is cleared round the drills at (145.07, 134.84) and (145.07, 136.11), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 1.74 mm of bare stretch at (145.7, 135.41). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PLL_DAC_SYNCN' on SIGNAL_INT1 at (145.7, 135.41), 1.74 mm between the drills at (145.07, 134.84) and (145.07, 136.11) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C133.57%7C146.34%2C138.65 serves each with its own layer_image region; all of them lie in x 143.84..147.57, y 134.41..136.41 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:146.34,110.71|146.34,111.98'TDC_D24' crosses between the drills at (146.34, 110.71) and (146.34, 111.98), whose anti-pads run together in the P3V3 plane on PWR_PLANE (fastest: TDC_D24 at 100 ps 10-90 %, ASSUMED)

      Along 'TDC_D24' on SIGNAL_INT1, the P3V3 plane on PWR_PLANE is cleared round the drills at (146.34, 110.71) and (146.34, 111.98), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.47 mm of bare stretch at (146.34, 111.34). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'TDC_D24' on SIGNAL_INT1 at (146.34, 111.34), 0.47 mm between the drills at (146.34, 110.71) and (146.34, 111.98) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A146.34%2C110.71%7C146.34%2C111.98 serves each with its own layer_image region; all of them lie in x 145.1..147.57, y 110.34..112.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:146.34,132.3|151.42,133.57'GA1' crosses between the drills at (147.61, 131.03) and (147.61, 132.3), whose anti-pads run together in the P3V3 plane on PWR_PLANE (fastest: GA1 at 100 ps 10-90 %, ASSUMED)

      Along 'GA1' on SIGNAL_INT1, the P3V3 plane on PWR_PLANE is cleared round the drills at (147.61, 131.03) and (147.61, 132.3), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.47 mm of bare stretch at (147.61, 131.66). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'GA1' on SIGNAL_INT1 at (147.61, 131.66), 0.47 mm between the drills at (147.61, 131.03) and (147.61, 132.3) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A146.34%2C132.3%7C151.42%2C133.57 serves each with its own layer_image region; all of them lie in x 146.38..148.84, y 130.66..132.66 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • merged:150.15,109.44|151.42,125.952 nets cross the slot of 22 drills from (150.15, 109.44) to (151.42, 125.95), whose anti-pads run together in the P3V3 plane on PWR_PLANE, between 2 pairs of drills (fastest: PLL_SDO at 100 ps 10-90 %, ASSUMED)

      The P3V3 plane on PWR_PLANE is cleared round a field of 22 drills from (150.15, 109.44) to (151.42, 125.95), and the clearances run together: the straight line from one drill to the next is bare all the way. 2 nets cross between drills of it at 2 place(s), each listed below with its two drills. Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. One decision covers the slot: whether these tracks may cross it, or the clearances should leave copper between the drills. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'PLL_SDO' on SIGNAL_INT1 at (150.18, 122.77), 0.58 mm between the drills at (150.15, 122.14) and (150.21, 123.35) in PWR_PLANE; other side: no plane on SIGNAL_INT2
      • 'TDC_D27' on SIGNAL_INT1 at (150.35, 115.15), 1.47 mm between the drills at (150.15, 114.52) and (150.15, 115.79) in PWR_PLANE; other side: no plane on SIGNAL_INT2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A150.15%2C109.44%7C151.42%2C125.95 serves each with its own layer_image region; all of them lie in x 148.89..152.42, y 113.52..123.77 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:GND|P3V3_PLL3 nets change reference between GND and P3V3_PLL at 4 vias, none with a reference that continues across (fastest: BYPASS at 100 ps 10-90 %, ASSUMED)

      At 4 via(s), on 3 net(s), the signal leaves a layer referenced by one of GND and P3V3_PLL for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 4 with none. 4 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P3V3_PLL are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'RESETN' at (128.27, 132.72), TOP_LAYER -> SIGNAL_INT2: P3V3_PLL on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 101.7 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3_PLL are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'PLLDAC_OUT' at (115.89, 140.97), TOP_LAYER -> SIGNAL_INT2: P3V3_PLL on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 12.7 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3_PLL are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'BYPASS' at (114.94, 136.21), TOP_LAYER -> SIGNAL_INT2: P3V3_PLL on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 7.8 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3_PLL are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'BYPASS' at (122.24, 137.48), TOP_LAYER -> SIGNAL_INT2: P3V3_PLL on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 7.8 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3_PLL are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=refchange%3AGND%7CP3V3_PLL serves each with its own layer_image region; all of them lie in x 112.94..130.27, y 130.72..142.97 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@PWR_PLANE:P3V3|P3V3_PLL16 nets cross the split between the P3V3 and P3V3_PLL planes on PWR_PLANE at 19 places, with no plane on the track's other side (fastest: BYPASS at 100 ps 10-90 %, ASSUMED)

      On PWR_PLANE the P3V3 and P3V3_PLL planes part, and 16 nets cross from one to the other at 19 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 19 crossing(s) the track's other neighbour carries a plane, which the return can use there; 15 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'BYPASS' on TOP_LAYER at (116.68, 135.1), 0.32 mm; other side: none: the signal layer is outermost
      • 'CP' on TOP_LAYER at (117.56, 135.02), 0.39 mm; other side: none: the signal layer is outermost
      • 'CP' on TOP_LAYER at (121.52, 140.1), 0.39 mm; other side: none: the signal layer is outermost
      • 'EXTOUT1_N' on TOP_LAYER at (134.14, 136.18), 0.32 mm; other side: none: the signal layer is outermost
      • 'EXTOUT1_P' on TOP_LAYER at (134.14, 135.68), 0.32 mm; other side: none: the signal layer is outermost
      • 'EXTOUT2_N' on TOP_LAYER at (134.14, 141.68), 0.32 mm; other side: none: the signal layer is outermost
      • 'EXTOUT2_P' on TOP_LAYER at (134.14, 142.18), 0.32 mm; other side: none: the signal layer is outermost
      • 'NetC1_2' on TOP_LAYER at (124.3, 144.94), 0.45 mm; other side: none: the signal layer is outermost
      • 'NetIC4_21' on TOP_LAYER at (125.9, 131.6), 0.32 mm; other side: none: the signal layer is outermost
      • 'NetIC4_45' on TOP_LAYER at (134.14, 140.18), 0.45 mm; other side: none: the signal layer is outermost
      • 'NetIC4_46' on TOP_LAYER at (134.2, 141.08), 0.4 mm; other side: none: the signal layer is outermost
      • 'NetIC4_58' on TOP_LAYER at (127.52, 144.94), 0.32 mm; other side: none: the signal layer is outermost
      • and 7 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=split%40PWR_PLANE%3AP3V3%7CP3V3_PLL serves each with its own layer_image region; all of them lie in x 107.27..135.3, y 130.45..146.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:VDDC_TDC@SIGNAL_INT1:116.46,111.16'TDC_STOP_DIS' crosses where the outline of the VDDC_TDC plane on SIGNAL_INT1 is drawn back, at 1 place, the longest 0.66 mm (fastest: TDC_STOP_DIS at 100 ps 10-90 %, ASSUMED)

      Along 'TDC_STOP_DIS' on SIGNAL_INT2, the VDDC_TDC plane on SIGNAL_INT1 has 0.66 mm under the track with no copper, at (116.46, 111.16), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 111.76..134.62, y 93.66..131.76 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 0 of the 1 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • 'TDC_STOP_DIS' on SIGNAL_INT2 at (116.46, 111.16), 0.66 mm over no copper; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=void%3AVDDC_TDC%40SIGNAL_INT1%3A116.46%2C111.16 serves each with its own layer_image region; all of them lie in x 115.46..117.52, y 109.81..112.44 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  7. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 3 boards×3

    Checked by the review, stands · Claude walker W3 (Cern session) — Checked: the reference break is read from the copper as stated. Whether it matters depends on the signal's edge rate and the receiver's margin, which no datasheet or app note on file fixes for this net; the impedance step and reflection figures are Probe's model, and the thresholds are its starting values. Layout practice, not a datasheet requirement. Left for the owner.

    At refchange:GND|P3V3, refchange:P3V3|VDDC_TDC, void:routed@SIGNAL_INT1|SIGNAL_INT2

    Each finding, with its own headline
    • refchange:GND|P3V359 nets change reference between GND and P3V3 at 90 vias, none with a reference that continues across (fastest: ALU_TRIGGER at 100 ps 10-90 %, ASSUMED)

      At 90 via(s), on 59 net(s), the signal leaves a layer referenced by one of GND and P3V3 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 90 with none. 90 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P3V3 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'RESETN' at (130.49, 87), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 101.7 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_4' at (147.61, 131.03), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 101.2 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'STATUS_LED' at (146.34, 122.14), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 98.4 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_3' at (103.51, 90.81), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 94.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_3' at (145.07, 137.38), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 94.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TERM_EN_1' at (147.61, 98.01), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 93.4 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_1' at (103.51, 94.93), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 92.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_1' at (145.07, 134.84), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 92.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_5' at (103.51, 86.68), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 89.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_TRIG_5' at (147.61, 132.3), TOP_LAYER -> BOTTOM_LAYER: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 89.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C45 (100 nF 0603) 2.7 mm away: 1.40 nH in the 1.150 mm cavity + 0.51 nH ESL + 0.88 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED): 87.6 ohm at the knee, 175 % of 50 ohm (assumed track impedance). None.
      • 'TERM_EN_2' at (147.61, 99.28), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 84.5 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TERM_EN_3' at (146.34, 117.06), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to GND on GND_PLANE; pure, no reference continues across; stitching none, 69.4 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 78 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=refchange%3AGND%7CP3V3 serves each with its own layer_image region; all of them lie in x 89.12..153.42, y 84.68..148.53 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:P3V3|VDDC_TDC13 nets change reference between P3V3 and VDDC_TDC at 13 vias, none with a reference that continues across (fastest: ALU_TRIGGER at 100 ps 10-90 %, ASSUMED)

      At 13 via(s), on 13 net(s), the signal leaves a layer referenced by one of P3V3 and VDDC_TDC for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 13 with none. 13 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether P3V3 and VDDC_TDC are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'TDC_STOP_DIS' at (120.02, 106.36), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 52.5 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_START_DIS' at (120.02, 110.17), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 50.5 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_START_FPGA' at (109.54, 119.38), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 46.7 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_IN_FPGA_2' at (101.6, 130.18), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 44.9 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_ADR0' at (119.38, 125.41), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 37.3 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_ADR1' at (118.75, 122.24), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 36.0 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_WRN' at (124.14, 105.73), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 33.6 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_ADR2' at (120.02, 121.92), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 30.0 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_RDN' at (125.25, 106.36), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 28.8 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'ALU_TRIGGER' at (118.11, 125.41), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 28.4 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_ADR3' at (121.29, 121.92), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 26.0 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'TDC_CSN' at (124.94, 110.81), TOP_LAYER -> SIGNAL_INT2: P3V3 on PWR_PLANE to VDDC_TDC on SIGNAL_INT1, GND on GND_PLANE; pure, no reference continues across; stitching none, 23.3 mm of track past the via on SIGNAL_INT2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 and VDDC_TDC are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 1 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=refchange%3AP3V3%7CVDDC_TDC serves each with its own layer_image region; all of them lie in x 99.6..127.25, y 103.73..132.18 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@SIGNAL_INT1|SIGNAL_INT220 nets on SIGNAL_INT2 cross the tracks routed through the VDDC_TDC pour on SIGNAL_INT1 at 27 places, the longest 41.61 mm; 25 run ALONG the cut round another net's track (fastest: ALU_TRIGGER at 100 ps 10-90 %, ASSUMED)

      The VDDC_TDC pour on SIGNAL_INT1 is cleared round tracks routed through it, and tracks on SIGNAL_INT2, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 27 place(s) on 20 net(s). 25 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 23.41 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 0 of the 27 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • 'TERM_EN_3' on SIGNAL_INT2 at (112.78, 104.14), 41.61 mm, running ALONG the bare copper for 14.45 mm, not across it over copper of ENABLE_INPUTS, TDC_STOP5, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_IN_FPGA_5' on SIGNAL_INT2 at (106.36, 117.48), 30.44 mm, running ALONG the bare copper for 23.41 mm, not across it over copper of ENABLE_INPUTS, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TERM_EN_5' on SIGNAL_INT2 at (112.7, 103.66), 28.67 mm, running ALONG the bare copper for 11.76 mm, not across it over copper of TDC_STOP5, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_START_FPGA' on SIGNAL_INT2 at (127.36, 127.56), 26.65 mm, running ALONG the bare copper for 20.93 mm, not across it over copper of PLL_SDO, PLL_CSN, PLL_SCLK, PLL_SDI, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_WRN' on SIGNAL_INT2 at (135.18, 109.78), 24.73 mm, running ALONG the bare copper for 4.57 mm, not across it over copper of TDC_D12, TDC_D13, TDC_D18, TDC_D19, TDC_D17, TDC_D21, TDC_D24, TDC_D25, TDC_D27, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TERM_EN_4' on SIGNAL_INT2 at (112.86, 104.62), 24.55 mm, running ALONG the bare copper for 9.18 mm, not across it over copper of P5V0, ENABLE_INPUTS, TDC_STOP5, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_STOP_DIS' on SIGNAL_INT2 at (127.6, 127.08), 24.51 mm, running ALONG the bare copper for 22.08 mm, not across it over copper of PLL_SDO, PLL_CSN, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_ADR0' on SIGNAL_INT2 at (145.56, 121.1), 24.49 mm, running ALONG the bare copper for 12.31 mm, not across it over copper of TDC_CSN, TDC_D25, TDC_D27, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_IN_FPGA_1' on SIGNAL_INT2 at (135.36, 130.86), 23.62 mm, running ALONG the bare copper for 14.24 mm, not across it over copper of PLL_SDO, PLL_CSN, PLL_SCLK, PLL_SDI, PLL_STATUS, GA1, GA0, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_IN_FPGA_4' on SIGNAL_INT2 at (105.89, 121.52), 23.17 mm, running ALONG the bare copper for 14.53 mm, not across it over copper of ENABLE_INPUTS, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_IN_FPGA_5' on SIGNAL_INT2 at (140.03, 126.37), 23.04 mm, running ALONG the bare copper for 19.87 mm, not across it over copper of PLL_SDO, PLL_CSN, PLL_SCLK, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • 'TDC_IN_FPGA_4' on SIGNAL_INT2 at (140.21, 126.84), 23.03 mm, running ALONG the bare copper for 19.95 mm, not across it over copper of PLL_SDO, PLL_CSN, PLL_SCLK, PLL_SDI, not a plane, to the end of the track; other side: GND on GND_PLANE, 0.5 mm from the track against 0.15 mm to SIGNAL_INT1: 77% of the return on SIGNAL_INT1
      • and 15 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=void%3Arouted%40SIGNAL_INT1%7CSIGNAL_INT2 serves each with its own layer_image region; all of them lie in x 94.57..153.08, y 97.11..139.43 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  8. NetCopperSplitmajorOpen

    TDC_START's copper is in 2 pieces joined only through R31: R31.1 and R7.2 are connected only if the part bonds its pins inside

    TDC_START's copper is in 2 pieces joined only through R31: R31.1 and R7.2 are connected only if the part bonds its pins inside. Piece 1: IC8.80, R31.2 and R34.2, on TOP_LAYER, over (111.79, 118.88) to (117.51, 121.47). Piece 2: R31.1 and R7.2, on TOP_LAYER, PWR_PLANE, SIGNAL_INT1, SIGNAL_INT2, GND_PLANE and BOTTOM_LAYER, 2 drill(s), over (109.14, 120.47) to (138.83, 140.2). Only R31 has pins in more than one piece; if those pins are bonded inside the package the net is whole, and if not, the copper leaves it open. A track or a via of the net joining the pieces closes it.

    At split:TDC_START

  9. observationOBS-191minorOpen

    LED and termination MOSFET gates have no pull-down, so their state is undefined until the carrier FPGA drives them

    The gates of the LED-driver and 50 ohm termination MOSFETs connect only to FMC pins with no pull-down, so LEDs and input terminations are undefined until the carrier FPGA drives them.

    Where it is

    MOSFETs (BSH103)FunctionGate netsOnly connection
    T1, T9, T2, T10, T3, T11LED driversLED_TRIG_1-5, STATUS_LEDJ6 pin (e.g. LED_TRIG_1 = J6.h35 and T1.1)
    T7A-T7E50 ohm termination switchesTERM_EN_1-5J6 pin (e.g. TERM_EN_1 = J6.g6 and T7A.1)

    No resistor holds any of them. ENABLE_INPUTS, by contrast, has R75 besides J6.g36 and the five CDCLVC1102 enable pins.

    Why it matters

    BSH103 turns on from a 0.4 V gate threshold (BSH103 datasheet, p.2). Before the carrier FPGA is configured, or with the mezzanine on a carrier that leaves those LA pins unused, the LEDs and the input terminations sit in whatever state leakage or the FPGA configuration pull-ups give them.

    A floating MOSFET gate can sit in partial conduction; for the terminations it also means the input impedance is undefined at power-up. A pull-down on each gate makes both off until the gateware drives them.

  10. observationOBS-192minorOpen

    LM1117 output banks are paralleled low-ESR tantalums, below the 0.3 ohm minimum ESR the datasheet sets for stability

    The LM1117 output banks on VDDC_TDC (IC12) and VDDC2_TDC (IC11) are paralleled 0.25 ohm low-ESR tantalums, about 0.06 and 0.13 ohm combined, below the 0.3 ohm minimum ESR TI sets for loop stability.

    The numbers

    QuantityValueSource
    Tantalum partCTE3528-21_47UF_6.3V_10%_LESR0250, named for 0.25 ohmBOM / netlist
    IC12 output (VDDC_TDC)4 x 47 uF (C13, C16, C19, C21) plus 4 x 100 nF X7R (C52, C55, C60, C64)netlist
    IC11 output (VDDC2_TDC)2 x 47 uF (C17, C27) plus 2 x 100 nF (C58, C59)netlist
    Combined tantalum ESR, VDDC_TDCabout 0.06 ohm, before the ceramics lower it furtherderived
    Combined tantalum ESR, VDDC2_TDCabout 0.13 ohm, before the ceramics lower it furtherderived
    LM1117 output capacitor ESR range0.3 ohm to 22 ohmLM1117 datasheet, p.15

    Both regulators also sit inside the TDC-GPX PLL servo loop through their ADJ pins.

    Why it matters

    An LM1117 with output ESR below its stable range can ring or oscillate; here that would also disturb the core-voltage servo that sets the TDC resolution. A standard-ESR tantalum, or a small series resistor, would put the ESR inside the range.

    The acam reference circuit uses 47 uF tantalums without naming an ESR, so the choice may be deliberate; bench behaviour would settle it.

  11. observationOBS-193minorOpen

    3.3 V CMOS outputs drive the FMC LA pins while the board expects VADJ = 2.5 V; only series resistors sit between them

    Every device driving the FMC LA pins runs its I/O from P3V3, while the board supervises VADJ at 2.5 V; only series resistors (and on PLL_STATUS nothing) sit between them.

    The drivers

    DriverSignalsBetween driver and J6
    TDC-GPX IC8 (Vddo = P3V3)data bus and flags, e.g. TDC_D0 from IC8 pin 1933 ohm networks RN1-RN5
    CDCLVC1102 IC1A-ETDC_IN_FPGA_1-5 (e.g. IC1A pin 8 to J6 h34)10 ohm R13A-E
    CDCLVC1102TDC_STARTR34
    AD9516 IC4SDO (output logic 1 = 2.7 V)R20 100 ohm
    AD9516 IC4 pin 6 (P3V3_PLL)PLL_STATUSnothing, direct

    No level translator is fitted.

    Why the carrier bank is at 2.5 V

    VADJ reaches only J6 and R72 47k, the top of the TPS3307 SENSE3 divider (R72, R71 47k, R73). The board supervises VADJ at 2.5 V (rail recorded 2.5 V), so the carrier bank receiving these signals runs at 2.5 V.

    Why it matters

    A 3.3 V output into a 2.5 V bank forward-biases the receiver's clamp to its VCCO. The series resistors bound that current, about 9 mA through 33 ohm and 30 mA through 10 ohm; PLL_STATUS has no bound at all. Whether that is acceptable depends on the carrier FPGA's input rating, which is not on this board. Stating the intended VADJ and the carrier requirement, or translating these lines, would settle it.

  12. observationOBS-194minorOpen

    PLL_DAC_SYNCN has no pull-up, so the AD5662 select floats until the carrier drives it

    PLL_DAC_SYNCN has no pull-up, so the AD5662 (IC2) select floats until the carrier drives it, and SCLK noise can clock a word into the DAC that retunes the VCTCXO.

    Where it is

    PLL_DAC_SYNCN has two pins only: J6 d24 and IC2 pin 5 (SYNC). PLL_SCLK is also undriven before the carrier configures its FPGA.

    Why it matters

    • While SYNC is low the DAC enables its input shift register and shifts in data on SCLK falling edges (AD5662 datasheet, p.7).
    • The AD9516 on the same bus has an internal 30 kohm pull-up on its select (AD9516 datasheet, p.12), so it idles deselected; the DAC does not.

    A floating active-low select can let noise on SCLK clock a partial or random word into the DAC, which retunes the VCTCXO. A pull-up to P3V3_PLL holds it idle.

  13. observationOBS-195minorOpen

    No test points: the regulated TDC core rails, the P5V0 clamp rail and the reset line have no probe access

    The board has no test points, so the servo-set TDC core rails, the P5V0 clamp rail and the reset line can only be probed at component pins.

    The board carries no test-point parts (refdes classes are B, C, D, F, FTG, IC, J, L, LD, OSC, R, RN, T). The nets a bring-up would probe first:

    NetWhat it isReachable at
    VDDC_TDCTDC core rail, servoed by the TDC-GPX PLLIC12, IC8, R63 and capacitors
    VDDC2_TDCTDC core rail, servoed by the TDC-GPX PLLIC11, IC8, R67, R69 and capacitors
    NetIC8_16the Phase servo signalcomponent pins
    P5V0zener clamp railcomponent pins
    RESETNTPS3307 outputIC13 pin 5 and its loads
    PLLDAC_OUTVCTCXO tuning voltagecomponent pins

    The core rails are set by a servo loop, so their built value is not the schematic value and measuring them is the only way to know it. A pad on each of these nets makes that a probe touch instead of a fine-pitch pin.

  14. observationOBS-196minorOpen

    Two title blocks carry another design's titles, and no sheet states a revision

    Two schematic title blocks carry another design's titles, and no sheet states a revision.

    SheetFileContentTitle block reads
    1FMC_TDC_1ns_5Cha.SchDoctop sheet"FMC Delay Top"
    2clock_generator.SchDocAD9516 PLL, AD5662 DAC and VCTCXO"ADC clock generator"

    Both titles are carried over from other FMC designs. Every sheet shows - in the Rev field; only the project number EDA-02290-V3-1 carries a version.

    A reader navigating by title lands on the wrong board, and a sheet without a revision cannot be matched to a built board. Correcting the two titles and filling Rev from the project version fixes both.

  15. observationOBS-197minorOpen

    Top silkscreen names the input network parts of channel A only; R7-R11 of channels B-E carry no designator

    Only channel A's input-network resistors are named on the top silkscreen; the twenty R7-R11 parts of channels B to E carry no designator.

    • Channel A has a labelled block R7A R8A R9A R10A R11A with leader lines to its parts.
    • On channels B to E the same parts sit in identical positions with no designator printed: R7B-E, R8B-E, R9B-E (the 50 ohm termination triplets), R10B-E (the 33 ohm series resistors) and R11B-E (the 4k12 pull-downs). For example R10B (33 ohm) sits beside D2B in the same position as R10A.
    • R13A-E, D2A-E and IC1A-E are labelled on every channel.

    Twenty fitted resistors without a printed designator make rework and probing of the input stages depend on the channel A pattern. Adding the labels, or a per-channel block like channel A, fixes it.

  16. DecapViaFanoutminorOpen

    DecapViaFanout: 13 components×13

    Checked by the review, stands · Claude walker W3 (Cern session) — Checked: the fan-out length is read from the copper as stated. The 0.5 nH limit is Probe's starting value, not a datasheet or vendor requirement on file; whether it matters depends on this capacitor's role in the rail's PDN target. Left for the owner.

    At C13, C14, C15, C16, C17, C18 and 7 more

    Each finding, with its own headline
    • C13C13 on 'VDDC_TDC': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C13 on 'VDDC_TDC': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C13.1 (rail) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH; C13.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.91 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C14C14 on 'P3V3': its rail pad reaches its via over 0.00 mm of track and its ground pad over 1.86 mm, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C14 on 'P3V3': its rail pad reaches its via over 0.00 mm of track and its ground pad over 1.86 mm, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C14.1 (rail) runs 0.00 mm along its copper to its nearest via, beside the pad; C14.2 (ground) runs 1.86 mm along its copper to its nearest via, 0.86 mm past the 1 mm beside the pad: 0.54 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.54 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C15C15 on 'P3V3': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C15 on 'P3V3': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C15.1 (rail) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH; C15.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.91 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C16C16 on 'VDDC_TDC': its rail pad reaches its via over 2.54 mm of track and its ground pad over 1.72 mm, adding about 1.41 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C16 on 'VDDC_TDC': its rail pad reaches its via over 2.54 mm of track and its ground pad over 1.72 mm, adding about 1.41 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C16.1 (rail) runs 2.54 mm along its copper to its nearest via, 1.54 mm past the 1 mm beside the pad: 0.96 nH; C16.2 (ground) runs 1.72 mm along its copper to its nearest via, 0.72 mm past the 1 mm beside the pad: 0.45 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.41 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C17C17 on 'VDDC2_TDC': its rail pad reaches its via over 2.17 mm of track and its ground pad over 1.73 mm, adding about 1.19 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C17 on 'VDDC2_TDC': its rail pad reaches its via over 2.17 mm of track and its ground pad over 1.73 mm, adding about 1.19 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C17.1 (rail) runs 2.17 mm along its copper to its nearest via, 1.17 mm past the 1 mm beside the pad: 0.73 nH; C17.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.19 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C18C18 on 'P3V3': its rail pad reaches its via over 2.57 mm of track and its ground pad over 1.73 mm, adding about 1.44 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C18 on 'P3V3': its rail pad reaches its via over 2.57 mm of track and its ground pad over 1.73 mm, adding about 1.44 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C18.1 (rail) runs 2.57 mm along its copper to its nearest via, 1.57 mm past the 1 mm beside the pad: 0.98 nH; C18.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.44 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C19C19 on 'VDDC_TDC': its rail pad reaches its via over 1.57 mm of track and its ground pad over 1.72 mm, adding about 0.81 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C19 on 'VDDC_TDC': its rail pad reaches its via over 1.57 mm of track and its ground pad over 1.72 mm, adding about 0.81 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C19.1 (rail) runs 1.57 mm along its copper to its nearest via, 0.57 mm past the 1 mm beside the pad: 0.36 nH; C19.2 (ground) runs 1.72 mm along its copper to its nearest via, 0.72 mm past the 1 mm beside the pad: 0.45 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.81 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C20C20 on 'P3V3': its rail pad reaches its via over 1.72 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C20 on 'P3V3': its rail pad reaches its via over 1.72 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C20.1 (rail) runs 1.72 mm along its copper to its nearest via, 0.72 mm past the 1 mm beside the pad: 0.45 nH; C20.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.91 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C21C21 on 'VDDC_TDC': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C21 on 'VDDC_TDC': its rail pad reaches its via over 1.73 mm of track and its ground pad over 1.73 mm, adding about 0.91 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C21.1 (rail) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH; C21.2 (ground) runs 1.73 mm along its copper to its nearest via, 0.73 mm past the 1 mm beside the pad: 0.46 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.91 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C27C27 on 'VDDC2_TDC': its rail pad reaches its via over 6.00 mm of track and its ground pad over 2.11 mm, adding about 3.82 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)

      C27 on 'VDDC2_TDC': its rail pad reaches its via over 6.00 mm of track and its ground pad over 2.11 mm, adding about 3.82 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C27.1 (rail) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 3.13 nH; C27.2 (ground) runs 2.11 mm along its copper to its nearest via, 1.11 mm past the 1 mm beside the pad: 0.69 nH. Each run past the pad as one conductor of a pair 2.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 3.82 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.78 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C45C45 on 'P3V3': its rail pad reaches its via over 1.53 mm of track and its ground pad over 1.49 mm, adding about 0.52 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C45 on 'P3V3': its rail pad reaches its via over 1.53 mm of track and its ground pad over 1.49 mm, adding about 0.52 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C45.2 (rail) runs 1.53 mm along its copper to its nearest via, 0.53 mm past the 1 mm beside the pad: 0.27 nH; C45.1 (ground) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.25 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.52 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C53C53 on 'P3V3': its rail pad reaches its via over 1.55 mm of track and its ground pad over 1.46 mm, adding about 0.51 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C53 on 'P3V3': its rail pad reaches its via over 1.55 mm of track and its ground pad over 1.46 mm, adding about 0.51 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C53.1 (rail) runs 1.55 mm along its copper to its nearest via, 0.55 mm past the 1 mm beside the pad: 0.28 nH; C53.2 (ground) runs 1.46 mm along its copper to its nearest via, 0.46 mm past the 1 mm beside the pad: 0.23 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.51 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C63C63 on 'P3V3': its rail pad reaches its via over 1.34 mm of track and its ground pad over 1.66 mm, adding about 0.51 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C63 on 'P3V3': its rail pad reaches its via over 1.34 mm of track and its ground pad over 1.66 mm, adding about 0.51 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C63.1 (rail) runs 1.34 mm along its copper to its nearest via, 0.34 mm past the 1 mm beside the pad: 0.17 nH; C63.2 (ground) runs 1.66 mm along its copper to its nearest via, 0.66 mm past the 1 mm beside the pad: 0.33 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.51 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.30 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  17. DuplicatePassiveminorOpen

    DuplicatePassive: 5 nets×5

    5 checked by the review by evaluation@esharp.se — 5 different reasons

    At NetD1A_3, NetD1B_3, NetD1C_3, NetD1D_3, NetD1E_3

    Each finding, with its own headline
    • NetD1A_3'NetD1A_3' and 'NetR7A_1' are bridged by 3 fitted resistors (R7A (150), R8A (150), R9A (150))

      'NetD1A_3' and 'NetR7A_1' are bridged by 3 fitted resistors: R7A (150), R8A (150), R9A (150) — 50R effective. Declare the intent: a second footprint provided for tuning is ordinary, and so is a mistake that halves a series or termination value. Nothing here says which this is.

    • NetD1B_3'NetD1B_3' and 'NetR7B_1' are bridged by 3 fitted resistors (R7B (150), R8B (150), R9B (150))

      'NetD1B_3' and 'NetR7B_1' are bridged by 3 fitted resistors: R7B (150), R8B (150), R9B (150) — 50R effective. Declare the intent: a second footprint provided for tuning is ordinary, and so is a mistake that halves a series or termination value. Nothing here says which this is.

    • NetD1C_3'NetD1C_3' and 'NetR7C_1' are bridged by 3 fitted resistors (R7C (150), R8C (150), R9C (150))

      'NetD1C_3' and 'NetR7C_1' are bridged by 3 fitted resistors: R7C (150), R8C (150), R9C (150) — 50R effective. Declare the intent: a second footprint provided for tuning is ordinary, and so is a mistake that halves a series or termination value. Nothing here says which this is.

    • NetD1D_3'NetD1D_3' and 'NetR7D_1' are bridged by 3 fitted resistors (R7D (150), R8D (150), R9D (150))

      'NetD1D_3' and 'NetR7D_1' are bridged by 3 fitted resistors: R7D (150), R8D (150), R9D (150) — 50R effective. Declare the intent: a second footprint provided for tuning is ordinary, and so is a mistake that halves a series or termination value. Nothing here says which this is.

    • NetD1E_3'NetD1E_3' and 'NetR7E_1' are bridged by 3 fitted resistors (R7E (150), R8E (150), R9E (150))

      'NetD1E_3' and 'NetR7E_1' are bridged by 3 fitted resistors: R7E (150), R8E (150), R9E (150) — 50R effective. Declare the intent: a second footprint provided for tuning is ordinary, and so is a mistake that halves a series or termination value. Nothing here says which this is.

  18. ReferencePlaneDiscontinuityminorOpen

    ReferencePlaneDiscontinuity: 2 boards×2

    Checked by the review, stands · Claude walker W3 (Cern session) — Checked: the reference break is read from the copper as stated. Whether it matters depends on the signal's edge rate and the receiver's margin, which no datasheet or app note on file fixes for this net; the impedance step and reflection figures are Probe's model, and the thresholds are its starting values. Layout practice, not a datasheet requirement. Left for the owner.

    At merged:145.07,114.52|145.07,115.79, refchange:P3V3|P3V3_PLL

    Each finding, with its own headline
    • merged:145.07,114.52|145.07,115.79'TERM_EN_5' crosses between the drills at (145.07, 114.52) and (145.07, 115.79), whose anti-pads run together in the GND plane on GND_PLANE (fastest: TERM_EN_5 at 20 ns 10-90 %, suggested by its name)

      Along 'TERM_EN_5' on SIGNAL_INT2, the GND plane on GND_PLANE is cleared round the drills at (145.07, 114.52) and (145.07, 115.79), and the two clearances run together: the straight line from one drill to the other is bare all the way, and the track crosses it, over 0.47 mm of bare stretch at (145.07, 115.18). Past one drill's anti-pad the return flows round on either side; here it cannot pass between the drills and detours round the whole merged clearance - the slot a row of pins or vias cuts in a plane. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'TERM_EN_5' on SIGNAL_INT2 at (145.07, 115.18), 0.47 mm between the drills at (145.07, 114.52) and (145.07, 115.79) in GND_PLANE; other side: no plane on SIGNAL_INT1

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=merged%3A145.07%2C114.52%7C145.07%2C115.79 serves each with its own layer_image region; all of them lie in x 143.84..146.3, y 114.18..116.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:P3V3|P3V3_PLL3 nets change reference between P3V3 and P3V3_PLL at 3 vias, none with a reference that continues across (fastest: PLL_STATUS at 100 ps 10-90 %, ASSUMED)

      At 3 via(s), on 3 net(s), the signal leaves a layer referenced by one of P3V3 and P3V3_PLL for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 3 served. Every site is served, so the finding is the lower tier (info). 3 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether P3V3 and P3V3_PLL are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'PLL_SCLK' at (121.29, 134.3), TOP_LAYER -> SIGNAL_INT1: P3V3_PLL on PWR_PLANE to P3V3 on PWR_PLANE; pure, no reference continues across; stitching served, 54.1 mm of track past the via on SIGNAL_INT1: At the 5 GHz knee of a 100 ps edge (1 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 on PWR_PLANE is 0.150 mm from GND on TOP_LAYER and P3V3_PLL on PWR_PLANE 0.150 mm from GND on TOP_LAYER: their own capacitance carries the return. Served.
      • 'PLL_STATUS' at (120.97, 139.07), TOP_LAYER -> SIGNAL_INT1: P3V3_PLL on PWR_PLANE to P3V3 on PWR_PLANE; pure, no reference continues across; stitching served, 46.3 mm of track past the via on SIGNAL_INT1: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 on PWR_PLANE is 0.150 mm from GND on TOP_LAYER and P3V3_PLL on PWR_PLANE 0.150 mm from GND on TOP_LAYER: their own capacitance carries the return. Served.
      • 'PLL_CSN' at (124.78, 132.4), TOP_LAYER -> SIGNAL_INT1: P3V3_PLL on PWR_PLANE to P3V3 on PWR_PLANE; pure, no reference continues across; stitching served, 29.9 mm of track past the via on SIGNAL_INT1: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. P3V3 on PWR_PLANE is 0.150 mm from GND on TOP_LAYER and P3V3_PLL on PWR_PLANE 0.150 mm from GND on TOP_LAYER: their own capacitance carries the return. Served.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/35/reference-planes?group=refchange%3AP3V3%7CP3V3_PLL serves each with its own layer_image region; all of them lie in x 118.97..126.78, y 130.4..141.07 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

Main parts

Part numberMakerDescriptionWhere
24AA64T-I/MCMICROCHIP TECHNOLOGY1.7-5.5V 64K I2C Serial EEPROMIC5
AD5662BRMZ-1ANALOG DEVICES2.7V to 5.5V, 250uA, Rail-to-Rail Output 16-Bit nanoDACIC2
AD9516-4BCPZANALOG DEVICES14-Output Clock Generator with Integrated 1.6 GHz VCOIC4
ASP-134604-01SAMTECConnector VITA 57, 160 Male contacts in 4 row cdghJ6
BZV55-B5V1NXP SEMICONDUCTORSZener DiodeD1
DS18B20U+DALLAS MAXIMProgrammable Resolution 1-Wire Digital ThermometerIC14
LF TVXO009917IQD FREQUENCY PRODUCTSOscillator 4 pins 1=VC 2=GND 3=OUT 4=+VsOSC1
LM336M-2.5/NOPBNATIONAL SEMICONDUCTORReference DiodeIC1
TDC-GPXACAM MESS-ELECTRONICMultifunctional High-End Time-to-Digital Converter (4 different operation modes, 81 ps up to 10 ps resolution)IC8
TPS3307-33DGNTEXAS INSTRUMENTSTriple Processor SupervisorsIC13
LM1117MPX-ADJ/NOPBNATIONAL SEMICONDUCTOR3-Terminal Regulator 1=Adj 2=OUT 3=INt 4=OUTIC11, IC12
571-0133FDIALIGHTLED x2 Yellow 1C2A-BOT_3C4A-TOPLD1, LD2, LD3
CDCLVC1102PWTEXAS INSTRUMENTS3.3 V and 2.5 V LVCMOS 1:2 High-Performance Clock BufferIC1A, IC1B, IC1C, IC1D, IC1E
EPL.00.250.NTNLEMOJ1, J2, J3, J4, J5
miniSMDC014FTYCO ELECTRONICSFuseF1A, F1B, F1C, F1D, F1E
BAR66INFINEONSerial DiodeD2A, D2B, D2C, D2D, D2E, D7
BSH103NXP SEMICONDUCTORSN-CHANNEL MOSFET WITH DIODET1, T10, T11, T2, T3, T7A and 5 more
BLM21PG221SN1DMURATAInductorL2
CB2012T4R7MTAIYO YUDENInductor With Magnetic coreL1
CC0603_22NF_50V_10%_X7RNon-polarised capacitorC1, C7
CTE3528-21_22UF_20V_10%_LESR0400Polarised capacitorC30, C31
R0603_100R_1%_0.1W_100PPMResistor - 1%R20, R67
R0603_47K_1%_0.1W_100PPMResistor - 1%R70, R71, R72
CC0603_820PF_50V_10%_X7RNon-polarised capacitorC10, C11, C12, C44
R0603_1K2_1%_0.1W_100PPMResistor - 1%R58, R60, R63, R68
R0603_1K_1%_0.1W_100PPMResistor - 1%R13, R61, R64, R65, R66
R0603_33R_1%_0.1W_100PPMResistor - 1%R10A, R10B, R10C, R10D, R10E
R0603_5K1_1%_0.1W_100PPMResistor - 1%R2, R4, R56, R74, R75
YC248-JR-0733RLYAGEODIL16 Resistor Network 8 Isolated Resistor 2%RN1, RN2, RN3, RN4, RN5
R0603_4K12_1%_0.1W_100PPMResistor - 1%R11A, R11B, R11C, R11D, R11E, R3
R0603_10K_1%_0.1W_100PPMResistor - 1%R24, R25, R26, R48, R59, R62, R73, R79
TCJA106M016R0200AVXPolarised capacitorC22, C23, C24, C25, C28, C29, C4, C68
R0603_10R_1%_0.1W_200PPMResistor - 1%R13A, R13B, R13C, R13D, R13E, R34 and 3 more
R0603_330R_1%_0.1W_100PPMResistor - 1%R1, R12, R5, R54, R55, R57 and 4 more
CTE3528-21_47UF_6.3V_10%_LESR0250Polarised capacitorC13, C14, C15, C16, C17, C18 and 5 more
R1206_150R_1%_0.25W_100PPMResistor - 1%R7A, R7B, R7C, R7D, R7E, R8A and 9 more
CC0603_100NF_50V_10%_X7RNon-polarised capacitorC1A, C1B, C1C, C1D, C1E, C2 and 40 more

About this design

Design
FMC TDC 1NS 5CHA — OHWR0033 R1
Designed in
Altium Designer
Board
6 copper layers, 76.5 × 69 mm, 217 components, 200 nets
Licence
CERN-OHL-1.1
Source
https://gitlab.com/ohwr/project/fmc-tdc-1ns-5cha-hw at commit 552616410b59
Attribution
CERN Open Hardware Repository, project ohwr/project/fmc-tdc-1ns-5cha-hw (commit 552616410b590fc1cf971f04c0610d7ecad806cf, 2025-04-10). Licence: CERN-OHL-1.1. Source: https://gitlab.com/ohwr/project/fmc-tdc-1ns-5cha-hw. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)