Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

RATOPUS CONTROL

OHWR0047 · revision R1

RATOPUS CONTROL (OHWR0047 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 4-layer board of 126.1 × 56.6 mm with 134 components and 71 nets, published under CERN-OHL-W-2.0.

review complete · 4 items need the designer's input · 16 findings: 10 major · 6 minor (19 items)

Open in the interactive viewerRead the full review

RATOPUS CONTROL (OHWR0047 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 16 findings: 10 major · 6 minor (19 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-90majorOpen

    Over-temperature comparators trip at about 800 ohm, which is within the PTC's own +/-50% R25 tolerance, so a high-tolerance RT1 can trip OTP at room temperature

    Both over-temperature comparators trip when the PTC reaches about 800 Ω, which lies inside RT1's own ±50 % R25 tolerance, so a high-tolerance thermistor can assert OTP at room temperature and stop the supply from starting.

    Where it is (OTP2)

    ``mermaid flowchart LR R["refd1, 5 V"] -- "RT1 PTC, 680 Ω R25" --> N["NetC14_2"] N -- "R40 6k8" --> G["GND_D"] N --> M["IC2B pin 6, minus"] R -- "R34 750" --> P["IC2B pin 5, plus<br/>R42 6k8 lower leg<br/>R43 100k hysteresis from otp2"] P --> C["IC2B output otp2"] M --> C ``

    • OTP2: RT1 (TDK B59721A0100A062, 680 Ω R25, Tsense 100 C) against the R34 750 / R42 6k8 reference with R43 100k hysteresis.
    • OTP1: the same bridge on IC2A: otp1_sig from the power board's thermistor (the same TDK part) against R33 750 / R41 6k8 / R44 100k.
    • The schematic's own node annotations ('Nom 4.55V' on IC2 pins 2 and 6, '4.50V' on pins 3 and 5) assume RT1 is exactly 680 Ω.

    The bridge arithmetic

    QuantityValueSource
    V+ with otp2 low5 V x 6.37k / 7.12k = 4.47 Vderived, fitted 1 % values
    RT1 at the trip6.8k x (5 / 4.47 - 1) = about 0.80 kΩderived
    Nominal margin4.55 V against 4.47 V = 0.08 Vschematic annotation; derived

    The thermistor

    QuantityValueSource
    R25680 Ω ±50 %, i.e. 340-1020 ΩTDK B59721A0100A062 datasheet, p.4
    Tsense,1100 C, defined at 4.7 kΩTDK datasheet, p.3
    R(Tsense - 5 C) / R(Tsense + 5 C)<= 5.5 kΩ / >= 13.3 kΩTDK datasheet, p.4

    Why it matters

    • Any part above about +18 % of R25 (over about 800 Ω) is already past the trip point at 25 C: OTP asserts, T8/T9 pull ssd1 and the supply cannot start.
    • Parts inside that band trip on the PTC's steep rise, somewhere below the 4.7 kΩ Tsense point, not at a defined 100 C.
    • The 0.08 V nominal margin is used up by the thermistor tolerance alone.

    Suggested fix: tie the trip to the PTC's defined steep region, which removes the dependence on R25: for example a threshold of a few kΩ (compare against Tsense's 4.7 kΩ), or an NTC with a tight R25 tolerance if a linear threshold is intended.

  2. observationOBS-550majorOpen

    BAT54C went end-of-life (Obsolete)

    Vendor (DigiKey) lifecycle for BAT54C (onsemi's listing) changed from "Active" to "Obsolete" since this board was reviewed. Placed as D1, D7. A sourcing/longevity risk; consider a replacement before production.

  3. observationOBS-558majorOpen

    LM358AD went end-of-life (Obsolete)

    Vendor (DigiKey) lifecycle for LM358AD (Texas Instruments's listing) changed from "Active" to "Obsolete" since this board was reviewed. Placed as IC10. A sourcing/longevity risk; consider a replacement before production.

  4. concernCON-001majorOpen

    [eol:BAT54C:Obsolete] BAT54C lifecycle changed from "Active" to "Obsolete" since this board was reviewed: OHWR0047 R1 RATOPUS CONTROL. A sourcing and longevity risk. Should this be replaced before the next build?

  5. concernCON-002majorOpen

    [eol:LM358AD:Obsolete] LM358AD lifecycle changed from "Active" to "Obsolete" since this board was reviewed: OHWR0047 R1 RATOPUS CONTROL. A sourcing and longevity risk. Should this be replaced before the next build?

  6. ReferencePlaneDiscontinuitymajorOpen

    2 nets cross one void in the Vccd1 plane on PLANE_1 at 2 places, the longest 1.85 mm; 2 over tracks of other nets routed inside it (fastest: NetC4_2 at 100 ps 10-90 %, ASSUMED)

    Along 'NetC4_2' on TOP_LAYER, the Vccd1 plane on PLANE_1 has 1.85 mm under the track with copper of ssd1, not a plane, at (110.95, 71.63), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 97.21..115.4, y 70.59..78.85. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

    • 'NetC4_2' on TOP_LAYER at (110.95, 71.63), 1.85 mm over copper of ssd1, not a plane; other side: none: the signal layer is outermost
    • 'ipk1' on TOP_LAYER at (100.58, 71.35), 1.04 mm over copper of ssd1, not a plane; other side: none: the signal layer is outermost

    Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/48/reference-planes?group=void%3AVccd1%40PLANE_1%3Ahole%2097.21%2C70.59%7C115.4%2C78.85 serves each with its own layer_image region; all of them lie in x 99.58..112.69, y 69.83..72.87 mm (board frame, Y up).

    Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    At void:Vccd1@PLANE_1:hole 97.21,70.59|115.4,78.85

  7. DecapViaFanoutmajorOpen

    DecapViaFanout: 2 components×2

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: fan-out lengths read from the copper stand; the 0.5 nH limit is Probe's starting value, not a requirement of the PWM controllers' datasheets, and no PDN target is stated. Left for the owner.

    At C2, C5

    Each finding, with its own headline
    • C2C2 on 'Vccd1': its rail pad reaches its via over 1.72 mm of track and its ground pad over 5.65 mm, adding about 2.85 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C2 on 'Vccd1': its rail pad reaches its via over 1.72 mm of track and its ground pad over 5.65 mm, adding about 2.85 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C2.2 (rail) runs 1.72 mm along its copper to its nearest via, 0.72 mm past the 1 mm beside the pad: 0.38 nH; C2.1 (ground) runs 5.65 mm along its copper to its nearest via, 4.65 mm past the 1 mm beside the pad: 2.47 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.85 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C5C5 on 'refd1': its rail pad reaches its via over 2.22 mm of track and its ground pad over 6.00 mm, adding about 3.30 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C5 on 'refd1': its rail pad reaches its via over 2.22 mm of track and its ground pad over 6.00 mm, adding about 3.30 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C5.2 (rail) runs 2.22 mm along its copper to its nearest via, 1.22 mm past the 1 mm beside the pad: 0.65 nH; C5.1 (ground) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 2.65 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 3.30 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  8. PartLifecyclemajorOpen

    LM293D on 3 placements (IC1, IC2, IC3): the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D

    LM293D on 3 placements (IC1, IC2, IC3): the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LM293D/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2023-11-03, 1,108 day(s) ago), so this is a substitution rather than a buy. The distributor reports 6,465 left. No approved alternate is recorded for this position.

    At IC1

  9. PartLifecyclemajorOpen

    PartLifecycle: 2 part numbers×2

    2 Obsolete · on 3 placements

    At D1, IC10

    Each finding, with its own headline
    • D1BAT54C on 2 placements (D1, D7): the distributor catalogue reports "Obsolete" for onsemi's BAT54C

      BAT54C on 2 placements (D1, D7): the distributor catalogue reports "Obsolete" for onsemi's BAT54C — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names FAIRCHILD SEMICONDUCTOR, and that is one line with onsemi: ON Semiconductor completed its acquisition of Fairchild Semiconductor on 2016-09-19 and renamed itself onsemi on 2021-08-05. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/BAT54C/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2018-09-30, 2,968 day(s) ago), so this is a substitution rather than a buy. The distributor reports 54,983 left. No approved alternate is recorded for this position.

    • IC10LM358AD on IC10: the distributor catalogue reports "Obsolete" for Texas Instruments's LM358AD

      LM358AD on IC10: the distributor catalogue reports "Obsolete" for Texas Instruments's LM358AD — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LM358AD/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2022-07-06, 1,593 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.

  10. SinglePointNetmajorOpen

    SinglePointNet: 2 pins×2

    2 checked by the review by a reviewer — 2 different reasons

    At IC10.5, IC10.6

    Each finding, with its own headline
    • IC10.5IC10.5 (IN2+) is an IC input left unconnected

      Pin IC10.5 (IN2+) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC10.6IC10.6 (IN2-) is an IC input left unconnected

      Pin IC10.6 (IN2-) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

  11. observationOBS-93minorOpen

    Schematic notes point at the wrong parts and one note is corrupted: 'T1 (pnp BJT)', 'T1 and T2' heat-spreaders, 'PWM chip (IC6)', 'Vcc2', and an 'Operation' note full of '#NAME?'

    Five notes on the control-board schematic name the wrong parts or are corrupted: 'T1 (pnp BJT)', the 'T1 and T2' heat-spreaders, 'PWM chip (IC6)', 'Vcc2', and an 'Operation' note full of '#NAME?'.

    Several notes on the single control-board sheet no longer match the designators on the board, and one is unreadable.

    The notes

    #Note on sheet 1What the board has
    1OTP block: 'PTC Thermister #2 (100 C) Place near T1 (pnp BJT)'T1 here is an MGSF1N02LT1G N-MOSFET in the OCP2 block; the only PNP is T6 (BCP53-16, the bootstrap pass transistor). On the power board T1 is the IPA80R280P7 800 V MOSFET. What RT1 is meant to sit next to cannot be read from the drawing.
    2'NOTE: Use large Cu heat-spreader area for T1 and T2 (atleast 2cm2 each)'Same problem. The layout puts its large pours on T6, T7 and T2, which suggests the note predates a re-annotation.
    3'To PWM chip (IC6) for generating comp signal', beside the ctrl outputIC6 here is the LM4041 Vaux1 indicator. On the power board IC6 is also an LM4041; the PWM controller there is IC4 (TL2843B).
    4LD1: 'Glows when Vcc2>10V'The monitored net is Vaux1, and the silkscreen says 'Vaux1 OK'.
    5Output Voltage Sensing block, 'Operation:'Reads 'Vout increases #NAME? Vka decreases #NAME? Vcsb increases #NAME? Vcsb' increases', and its last line is clipped by the text frame. The note explains the loop's sign chain; the arrows were evidently lost as spreadsheet formula errors.

    Why it matters

    For a published open-hardware design these notes are where a reader learns intent, so they should name the right parts.

    Read from the rendered schematic sheet 1, compared with the netlist and BOM of this board and the BOM of the power board.

  12. observationOBS-478minorOpen

    OVP detector IC4: the divider sets the trip at 14.8 V, not the 14.4 V the schematic states, and once tripped IC4 sinks 14.3-15.0 mA, above its 12 mA recommended maximum

    The OVP detector IC4 trips at 14.8 V nominal, not the 14.4 V the schematic states, and once tripped it sinks 14.3-15.0 mA, above the LM4041's 12 mA recommended maximum.

    Where it is

    IC4 (LM4041DIM3-ADJ):

    • cathode (pin 2) on Vout1
    • FB (pin 1, NetIC4_1) set by R53 20k (Vout1 to FB) and R66 220k (FB to GND_O); R67 220k goes to the test_ovp pad
    • anode (pin 3, NetIC4_3) driving the HCNR200 LED (IC5 pins 2-1) through R64 820 Ω

    The schematic heading says 'Power off when Vout>14.4V i.e. 120% of nominal value', with a note 'Min.10mA at OV'.

    1. The trip point

    QuantityValueSource
    Shunt equationVO = VREF × (R2/R1 + 1), R1 from cathode to FBLM4041 datasheet p.23, Fig. 8-3
    Nominal trip1.233 V × (220k/20k + 1) = 14.80 V, 123 % of 12 Vderived
    Trip band, D-grade reference ±12 mV and 1 % resistors1.221 × (1 + 217.8k/20.2k) ≈ 14.39 V to 1.245 × (1 + 222.2k/19.8k) ≈ 15.22 VLM4041 datasheet p.15; BOM; derived
    Stated trip14.4 V, the extreme bottom of the band rather than its centreschematic OVP heading
    With test_ovp grounded (R67 in parallel with R66, 110k)1.233 × (110k/20k + 1) ≈ 8.0 V, as intended for a testderived

    2. The current once tripped

    In this comparator use nothing but R64 sets the device current: once Vout1 crosses the threshold, IC4 conducts as hard as the anode path allows, so IK = (Vout1 − VF − VKA) / R64.

    QuantityValueSource
    HCNR200 LED VF1.3 min, 1.6 typ, 1.85 max V at 10 mAHCNR200 datasheet p.8
    LM4041 VKA1.24 V, recommended minimum output voltageLM4041 datasheet p.5
    IK at the 14.8 V trip, VF = 1.85 V(14.8 − 1.85 − 1.24) / 820 = 11.71 / 820 = 14.3 mAderived
    IK at the 14.8 V trip, VF = 1.6 V(14.8 − 1.6 − 1.24) / 820 = 14.6 mAderived
    IK at the 14.8 V trip, VF = 1.3 V(14.8 − 1.3 − 1.24) / 820 = 12.26 / 820 = 15.0 mAderived
    Rise above the trip1 / 820 Ω = 1.22 mA per further voltderived
    LM4041 recommended reverse current60 µA to 12 mALM4041 datasheet p.5
    LM4041 absolute maximum reverse current20 mALM4041 datasheet p.5
    Vout1 at which IK reaches 20 mA20 mA × 820 Ω + 1.24 V + VF = 16.40 + 1.24 + (1.3 to 1.85) = 18.9-19.5 V (VF is specified at 10 mA and rises at 20 mA, so this is a lower bound)derived

    The note 'Min.10mA at OV' shows 10 mA was the intent.

    Fix

    OVP then shuts the converter down, so the stress is transient. A larger R64 keeps IC4 inside its recommended range: 1.2 kΩ gives (14.8 − 1.85 − 1.24) / 1200 to (14.8 − 1.3 − 1.24) / 1200 = 9.8-10.2 mA at trip, matching the 10 mA note; 1 kΩ gives 11.7-12.3 mA, which is still at the 12 mA limit. The resistor values or the 14.4 V annotation should also be reconciled.

  13. observationOBS-489minorOpen

    OVP detector IC4 LM4041-ADJ sees about 12 V cathode-to-anode in normal operation and trips at 14.8 V, above its 10 V recommended range and at its 15 V absolute maximum

    The OVP detector IC4 (LM4041DIM3-ADJ) is used above the adjustable range its datasheet allows: it has about 12 V cathode-to-anode in normal operation and about 14.8 V just below its trip, against a recommended 10 V maximum and a 15 V absolute maximum. With 1 % resistors the trip, and so the peak voltage on IC4, can be above 15 V.

    Where it is

    IC4 cathode (pin 2) is on Vout1, the 12 V output ('Nom 12V', and the OVP heading's 14.4 V is '120% of nominal value'). FB (pin 1, NetIC4_1) sits on R53 20k to Vout1 and R66 220k to GND_O (R67 220k goes to the test_ovp pad). The anode (pin 3, NetIC4_3) goes only to R64 820 Ω, then to the HCNR200 IC5 LED on NetIC5_2, which R70 22k returns to GND_O.

    This is the datasheet's adjustable shunt (Figure 8-3: R1 cathode to FB, R2 FB to ground), except that R2 returns to GND_O instead of the anode. So 14.8 V is a detection threshold, and the voltage across IC4 is set by Vout1:

    • Below the trip IC4 is off, so nothing flows through R64 and the anode sits near GND_O (R70 pulls NetIC5_2 down). The cathode-to-anode voltage is then about Vout1.
    • At the trip IC4 starts to sink current and its cathode-to-anode voltage falls (OBS-478 covers the current it then sinks).

    The numbers

    QuantityValueSource
    LM4041-ADJ output voltage, recommended1.24 V to 10 V ('can be adjusted to any value in the range of 1.24V through 10V')LM4041 datasheet p.5, p.21
    LM4041-ADJ maximum output voltage, absolute maximum15 VLM4041 datasheet p.5
    LM4041-ADJ reverse current, recommended60 µA to 12 mA (20 mA absolute maximum)LM4041 datasheet p.5
    Electrical characteristics valid forIRMIN ≤ IR ≤ 12 mA, VREF ≤ VOUT ≤ 10 V; reference tolerance stated at VOUT = 5 VLM4041 datasheet p.13
    VREF (typical)1.233 VLM4041 datasheet p.13
    DividerR53 20k (Vout1 to FB), R66 220k (FB to GND_O), both 1 %netlist NetIC4_1; BOM
    Programmed thresholdVO = VREF × (R2/R1 + 1) = 1.233 × (220k/20k + 1) = 14.80 VLM4041 datasheet p.21 Eq. 2; derived
    IC4 cathode-to-anode, normal operation≈ Vout1 = 12 V nominal (anode near GND_O while IC4 is off)schematic; netlist NetIC4_3, NetIC5_2; derived
    IC4 cathode-to-anode, just below trip≈ 14.8 V, 0.2 V (1.4 %) under the 15 V absolute maximumderived
    Trip with 1 % resistors, nominal VREF1.233 × (1 + 217.8k/20.2k) = 14.53 V to 1.233 × (1 + 222.2k/19.8k) = 15.07 VBOM; derived

    The upper end of the resistor tolerance alone puts the voltage IC4 must hold off before it trips above its 15 V absolute maximum, before any reference error is counted. The reference error cannot be bounded from the datasheet at all, because every electrical limit, including the ±12 mV D-grade tolerance, is given only for VOUT ≤ 10 V, and the datasheet notes that 'Reference voltage and temperature coefficient can change with output voltage' (p.14). A fast overshoot that outruns the shutdown also reaches IC4's cathode directly.

    How this differs from OBS-478

    OBS-478 is about where the trip lands (14.8 V against the 14.4 V the schematic states) and the current IC4 sinks once it has tripped. This observation is about the voltage across IC4 before it trips: the whole normal operating point is outside the part's recommended range, and the trip point is at its absolute maximum. It also means the tolerance band OBS-478 quotes rests on characteristics the datasheet does not guarantee above 10 V.

    Options

    • Keep IC4's cathode-to-anode voltage at or below 10 V, for example by putting a resistor or a Zener in series with the cathode so that the device never sees all of Vout1, and re-derive the threshold.
    • Or use a shunt reference rated for the full Vout1 overvoltage range.
  14. ReferencePlaneDiscontinuityminorOpen

    8 nets change reference between GND_D and Vccd1 at 15 vias, none with a reference that continues across (fastest: NetC14_2 at 100 ps 10-90 %, ASSUMED)

    At 15 via(s), on 8 net(s), the signal leaves a layer referenced by one of GND_D and Vccd1 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 15 served. Every site is served, so the finding is the lower tier (info). 15 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND_D and Vccd1 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

    • 'ssd2' at (74.75, 70.9), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 53.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ssd2' at (100.25, 65.5), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 53.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ssd2' at (106.22, 79.23), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 53.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'refd2' at (72.5, 71.38), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 49.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ctrl' at (67.3, 66.6), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 48.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ssd1' at (77.6, 69.98), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 40.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ssd1' at (80.33, 77.9), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 40.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ssd1' at (105.5, 65.25), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 40.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ipk2' at (68.25, 71.75), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 39.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'ipk2' at (95.5, 61), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 39.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'NetC14_2' at (109.02, 68.57), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 22.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
    • 'otp1_sig' at (88.72, 61.45), TOP_LAYER -> BOTTOM_LAYER: Vccd1 on PLANE_1 to GND_D on PLANE_2; pure, no reference continues across; stitching served, 21.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_D on PLANE_2 and Vccd1 on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Measured for reference: C11 (100 nF 0603) 2.4 mm away: 0.15 nH in the 0.127 mm cavity + 0.51 nH ESL + 0.33 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED): 31.1 ohm at the knee, 62 % of 50 ohm (assumed track impedance). Served.
    • and 3 more

    Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/48/reference-planes?group=refchange%3AGND_D%7CVccd1 serves each with its own layer_image region; all of them lie in x 59.4..116.5, y 59..81.23 mm (board frame, Y up).

    The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    At refchange:GND_D|Vccd1

  15. DecapViaFanoutminorOpen

    C8 on 'Vccd1': its rail pad reaches its via over 4.33 mm of track and its ground pad over 0.00 mm, adding about 1.77 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 1 uF bulk capacitor: its inductance matters only far above the band it serves)

    C8 on 'Vccd1': its rail pad reaches its via over 4.33 mm of track and its ground pad over 0.00 mm, adding about 1.77 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 1 uF bulk capacitor: its inductance matters only far above the band it serves). C8.2 (rail) runs 4.33 mm along its copper to its nearest via, 3.33 mm past the 1 mm beside the pad: 1.77 nH; C8.1 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.77 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    At C8

  16. ConnectorDomainMixedminorOpen

    J1 takes 5 different supplies off the board on one connector: Vdc (48.0 V), 13p7v (13.7 V), Vccd1 (10.4 V), Vcci (10.4 V), refd1 (5.0 V)

    J1 carries 5 different supplies out of the board on one connector: Vdc (48.0 V) on 1, 13p7v (13.7 V) on 10, Vccd1 (10.4 V) on 6, Vcci (10.4 V) on 14, refd1 (5.0 V) on 7. Declare the intent. Two rails on one connector is ordinary in a docking or power-distribution interface and a hazard in a signal one, and the difference is not visible from the netlist — but note that adjacent contacts at different voltages are exactly what a mirrored, reversed or off-by-one cable shorts together, so the cost of getting the mating wrong is a rail collision rather than a dead signal. If this is a standard connector, declare its family (connector_family_declare) and file the standard's contact map: supplies on the contacts it assigns to power are then not reported.

    At J1

Main parts

Part numberMakerDescriptionWhere
ACPL-C87B-000EAVAGO TECHNOLOGIESPrecision Optically Isolated Voltage SensorIC9
B59721A0100A062EPCOS / TDKThermistor NTC (Positive Temperature Coefficient)RT1
BCP53NXP SEMICONDUCTORSPNP TransistorT6
BZV55-B11NEXPERIAZener DiodeD3
BZV55-B12NEXPERIAZener DiodeD2
BZV55-C2V4NEXPERIAZener DiodeD8
HCNR200-300EAVAGO TECHNOLOGIESHigh-Linearity Analog OptocouplerIC5
KPH-1608CGCKKINGBRIGHTLED Green 1C 2ALD1
L78L05ABUTRST MICROELECTRONICS3-Terminal Regulator 1=OUT 2=GND 3=INIC7
LM358ADTEXAS INSTRUMENTSDual Operational AmplifierIC10
SMBJ12AFAIRCHILD SEMICONDUCTORZener DiodeD4
TSW-104-23-L-DSAMTECConnector 8 MaleJ2
TSW-108-23-L-DSAMTECConnector 16 MaleJ1
BAT54CFAIRCHILD SEMICONDUCTORDual Common Cathode Schottky DiodesD1, D7
BAV99FAIRCHILD SEMICONDUCTORSerial DiodeD5, D6
BC817-25NXP SEMICONDUCTORSNPN TransistorT10, T12
BCP56-16NXP SEMICONDUCTORSNPN TransistorT2, T7
LM293DTEXAS INSTRUMENTSDual Operational AmplifierIC1, IC2, IC3
LM4041DIM3-ADJ/NOPBTEXAS INSTRUMENTSPrecision Reference 1=Adj 2=Cathode 3=AnodeIC4, IC6, IC8
MGSF1N02LT1GON SEMICONDUCTORN-CHANNEL MOSFET WITH DIODET1, T11, T3, T4, T5, T8, T9
08051A561JAT2AAVXNon-polarised capacitorC18
CC0805_1NF_50V_10%_X7RGENERICNon-polarised capacitorC23
CC0805_560PF_50V_5%_NP0GENERICNon-polarised capacitorC7
CC0805_6.8NF_50V_10%_X7RGENERICNon-polarised capacitorC17
CC2220_4.7UF_100V_10%_X7RGENERICNon-polarised capacitorC3
R0805_10R_1%_0.125W_200PPMGENERICResistor - 1%R6
R0805_15K_1%_0.125W_100PPMGENERICResistor - 1%R24
R0805_160K_1%_0.125W_100PPMGENERICResistor - 1%R29
R0805_17K4_0.1%_0.1W_10PPMGENERICResistor - 0.1%R73
R0805_1M_1%_0.125W_100PPMGENERICResistor - 1%R26
R0805_20K_1%_0.125W_100PPMGENERICResistor - 1%R53
R0805_2K2_1%_0.125W_100PPMGENERICResistor - 1%R10
R0805_2K_0.1%_0.125W_25PPMGENERICResistor - 0.1%R45
R0805_39R_1%_0.125W_100PPMGENERICResistor - 1%R19
R0805_3K9_1%_0.125W_100PPMGENERICResistor - 1%R22
R0805_4K7_1%_0.125W_100PPMGENERICResistor - 1%R72
R0805_820R_1%_0.125W_100PPMGENERICResistor - 1%R64
R0805_0R_JUMPERGENERICResistorR50, R56
R0805_10K_1%_0.125W_100PPMGENERICResistor - 1%R51, R59
R0805_12K_1%_0.125W_100PPMGENERICResistor - 1%R17, R2

About this design

Design
RATOPUS CONTROL — OHWR0047 R1
Designed in
Altium Designer
Board
4 copper layers, 126.1 × 56.6 mm, 134 components, 71 nets
Licence
CERN-OHL-W-2.0
Source
https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w at commit aa0f8b805fdf
Attribution
CERN Open Hardware Repository, project ohwr/project/psu-rad-acdc-230v-12v5v-110w (commit aa0f8b805fdf947458e09c4c64a58de31cbf2940, 2025-04-10). Licence: CERN-OHL-W-2.0. Source: https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)