RATOPUS STAGE DCDC 12V
OHWR0050 · revision R1
RATOPUS STAGE DCDC 12V (OHWR0050 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 4-layer board of 160 × 100 mm with 310 components and 136 nets, published under CERN-OHL-W-2.0.
review 87% walked · 18 findings: 11 major · 7 minor (37 items)
Open in the interactive viewerRead the full review

Design review
Probe recorded 18 findings: 11 major · 7 minor (37 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.
Both over-temperature comparators trip near 0.8 k, inside the PTCs' own +/-50 % R25 tolerance, so OTP can assert at room temperature
The two over-temperature detectors (IC8A with RT1, IC8B with RT2, both TDK B59721A0100A062 PTCs, 680 R +/-50 % at 25 C, Tsense 100 C) trip when the PTC rises to about 0.8 k. That is inside the thermistors' own room-temperature tolerance (340-1020 R), so a high-tolerance part asserts OTP at ambient and holds the converter's soft-start low through T9/T8; the guaranteed switching region (<= 5.5 k at 95 C, >= 13.3 k at 105 C) is never used. The identical bridge on OHWR0047 RATOPUS CONTROL is OBS-90.
The bridge
``
mermaid flowchart LR V["Vref 5 V (IC6 TL2843B)"] -- "RT1 PTC 680 R" --> N["NetC47_2 -> IC8 pin 2 (-)"] N -- "R73 6k8" --> G[GND_I] V -- "R66 750" --> P["NetIC8_3 -> IC8 pin 3 (+), R77 6k8 to GND, R82 100k from otp1"] P --> O["otp1 -> T9 gate -> ss pulled low"] N --> O``RT2 / R75 / R67 / R78 / R81 form the same bridge on IC8B (otp2, T8).
The numbers
Quantity Value Source V(-) with RT1 = 680 R 5 x 6.8 / 7.48 = 4.55 V derived V(+) with otp low (R82 to ground side) about 4.47 V derived, 1 % values PTC resistance at the trip about 0.80 k derived R25 of B59721A0100A062 680 R +/-50 % (340-1020 R) TDK data sheet p4 R(Tsense - 5 C) / R(Tsense + 5 C) <= 5.5 k / >= 13.3 k TDK data sheet p4 A reference leg set between 5.5 k and 13.3 k of PTC resistance (for example R66/R77 chosen for about 9 k) would make the trip follow the specified 100 C switching point.
BAT54C went end-of-life (Obsolete)
Vendor (DigiKey) lifecycle for BAT54C (onsemi's listing) changed from "Active" to "Obsolete" since this board was reviewed. Placed as D13, D25, D26. A sourcing/longevity risk; consider a replacement before production.
LM358AD went end-of-life (Obsolete)
Vendor (DigiKey) lifecycle for LM358AD (Texas Instruments's listing) changed from "Active" to "Obsolete" since this board was reviewed. Placed as IC15. A sourcing/longevity risk; consider a replacement before production.
- concernCON-001majorOpen
[eol:BAT54C:Obsolete] BAT54C lifecycle changed from "Active" to "Obsolete" since this board was reviewed: OHWR0050 R1 RATOPUS STAGE DCDC 12V. A sourcing and longevity risk. Should this be replaced before the next build?
- concernCON-002majorOpen
[eol:LM358AD:Obsolete] LM358AD lifecycle changed from "Active" to "Obsolete" since this board was reviewed: OHWR0050 R1 RATOPUS STAGE DCDC 12V. A sourcing and longevity risk. Should this be replaced before the next build?
- DecapViaFanoutmajorOpen
DecapViaFanout: 6 components×6
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: fan-out lengths read from the copper stand; the 0.5 nH limit is Probe's starting value, not a TL2843 requirement, and no PDN target is stated. Left for the owner.
At C12, C16, C18, C33, C35, C50
Each finding, with its own headline
C12C12 on 'Vcc2': its ground pad over 2.58 mm, adding about 0.84 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C12 on 'Vcc2': its ground pad over 2.58 mm, adding about 0.84 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C12.2 (rail) not measured: its tracks reach no via within 6 mm; C12.1 (ground) runs 2.58 mm along its copper to its nearest via, 1.58 mm past the 1 mm beside the pad: 0.84 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.84 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C16C16 on 'Vcc': its ground pad over 6.00 mm, adding about 2.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C16 on 'Vcc': its ground pad over 6.00 mm, adding about 2.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C16.2 (rail) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure; C16.1 (ground) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 2.65 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.65 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C18C18 on 'Vout': its rail pad reaches its via over 2.21 mm of track, adding about 0.64 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C18 on 'Vout': its rail pad reaches its via over 2.21 mm of track, adding about 0.64 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C18.2 (rail) runs 2.21 mm along its copper to its nearest via, 1.21 mm past the 1 mm beside the pad: 0.64 nH; C18.1 (ground) not measured: its own track joins it to IC4.2 (0.00 mm) before any via: it serves that pin directly, and its loop does not run through its vias. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.64 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C33C33 on 'Vref': its rail pad reaches its via over 6.00 mm of track, adding about 2.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C33 on 'Vref': its rail pad reaches its via over 6.00 mm of track, adding about 2.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C33.1 (rail) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 2.65 nH; C33.2 (ground) not measured: its tracks reach no via within 6 mm. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.65 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.76 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.25 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C35C35 on 'Vref': its rail pad reaches its via over 3.97 mm of track and its ground pad over 2.00 mm, adding about 2.11 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C35 on 'Vref': its rail pad reaches its via over 3.97 mm of track and its ground pad over 2.00 mm, adding about 2.11 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C35.2 (rail) runs 3.97 mm along its copper to its nearest via, 2.97 mm past the 1 mm beside the pad: 1.57 nH; C35.1 (ground) runs 2.00 mm along its copper to its nearest via, 1.00 mm past the 1 mm beside the pad: 0.53 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.11 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.76 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.25 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C50C50 on 'Vcc': its ground pad over 5.87 mm, adding about 2.58 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C50 on 'Vcc': its ground pad over 5.87 mm, adding about 2.58 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C50.2 (rail) not measured: its own track joins it to IC10.8 (2.41 mm) before any via: it serves that pin directly, and its loop does not run through its vias; C50.1 (ground) runs 5.87 mm along its copper to its nearest via, 4.87 mm past the 1 mm beside the pad: 2.58 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.58 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.84 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
- PartLifecyclemajorOpen
PartLifecycle: 2 part numbers×2
2 Obsolete · on 6 placements
At C10, IC10
Each finding, with its own headline
C10CKG45NX7S2A106M500JH on 3 placements (C10, C11, C14): the distributor catalogue reports "Obsolete" for TDK's CKG45NX7S2A106M500JH
CKG45NX7S2A106M500JH on 3 placements (C10, C11, C14): the distributor catalogue reports "Obsolete" for TDK's CKG45NX7S2A106M500JH — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TDK). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/CKG45NX7S2A106M500JH/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.
IC10LM293D on 3 placements (IC10, IC5, IC8): the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D
LM293D on 3 placements (IC10, IC5, IC8): the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LM293D/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2023-11-03, 1,108 day(s) ago), so this is a substitution rather than a buy. The distributor reports 6,465 left. No approved alternate is recorded for this position.
- PartLifecyclemajorOpen
PartLifecycle: 2 part numbers×2
2 Obsolete · on 4 placements
At D13, IC15
Each finding, with its own headline
D13BAT54C on 3 placements (D13, D25, D26): the distributor catalogue reports "Obsolete" for onsemi's BAT54C
BAT54C on 3 placements (D13, D25, D26): the distributor catalogue reports "Obsolete" for onsemi's BAT54C — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names FAIRCHILD SEMICONDUCTOR, and that is one line with onsemi: ON Semiconductor completed its acquisition of Fairchild Semiconductor on 2016-09-19 and renamed itself onsemi on 2021-08-05. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/BAT54C/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2018-09-30, 2,968 day(s) ago), so this is a substitution rather than a buy. The distributor reports 54,983 left. No approved alternate is recorded for this position.
IC15LM358AD on IC15: the distributor catalogue reports "Obsolete" for Texas Instruments's LM358AD
LM358AD on IC15: the distributor catalogue reports "Obsolete" for Texas Instruments's LM358AD — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LM358AD/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2022-07-06, 1,593 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.
- ReferencePlaneDiscontinuitymajorOpen
ReferencePlaneDiscontinuity: 3 boards×3
3 checked by the review by Claude walker V3 (cern-01 session) — 3 different reasons
At split@PLANE_1:Vcc|Vout, void:routed@PLANE_1|PLANE_2, void:routed@PLANE_1|TOP_LAYER
Each finding, with its own headline
split@PLANE_1:Vcc|Vout'otp2' crosses the split between the Vcc and Vout planes on PLANE_1 at 1 place, with no plane on the track's other side (fastest: otp2 at 100 ps 10-90 %, ASSUMED)
On PLANE_1 the Vcc and Vout planes part, and 'otp2' crosses from one to the other at 1 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 1 crossing(s) the track's other neighbour carries a plane, which the return can use there; 1 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'otp2' on TOP_LAYER at (76.5, 54.18), 5.54 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=split%40PLANE_1%3AVcc%7CVout serves each with its own layer_image region; all of them lie in x 71.9..78.22, y 52.47..55.9 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:routed@PLANE_1|PLANE_22 nets on PLANE_1 cross the tracks routed through the GND_I pour on PLANE_2 at 2 places, the longest 95.9 mm; 2 run ALONG the cut round another net's track (fastest: comp at 100 ps 10-90 %, ASSUMED)
The GND_I pour on PLANE_2 is cleared round tracks routed through it, and tracks on PLANE_1, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 2 place(s) on 2 net(s). 2 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 88.47 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'otp2' on PLANE_1 at (39.73, 3.6), 95.9 mm, running ALONG the bare copper for 88.47 mm, not across it over copper of uvlo, not a plane, to the end of the track; other side: no plane on TOP_LAYER
- 'comp' on PLANE_1 at (3.5, 20.06), 8.57 mm, running ALONG the bare copper for 2.64 mm, not across it over copper of ovp, not a plane, to the end of the track; other side: no plane on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=void%3Arouted%40PLANE_1%7CPLANE_2 serves each with its own layer_image region; all of them lie in x -0.26..80.11, y 2.6..23.5 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:routed@PLANE_1|TOP_LAYER8 nets on TOP_LAYER cross the tracks routed through the Vcc pour on PLANE_1 at 10 places, the longest 37 mm; 2 run ALONG the cut round another net's track (fastest: NetC46_2 at 100 ps 10-90 %, ASSUMED)
The Vcc pour on PLANE_1 is cleared round tracks routed through it, and tracks on TOP_LAYER, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 10 place(s) on 8 net(s). 2 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 16.09 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'ovp' on TOP_LAYER at (91, 0.9), 37 mm, running ALONG the bare copper for 16.09 mm, not across it over copper of otp2, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'comp' on TOP_LAYER at (10.52, 43.95), 7.99 mm, running ALONG the bare copper for 4.43 mm, not across it over copper of ss, not a plane; other side: none: the signal layer is outermost
- 'cs_unfilt' on TOP_LAYER at (52.7, 42.42), 1.58 mm over copper of ss, not a plane; other side: none: the signal layer is outermost
- 'NetC46_2' on TOP_LAYER at (36.2, 42.42), 1.54 mm over copper of ss, not a plane; other side: none: the signal layer is outermost
- 'NetIC15_2' on TOP_LAYER at (124.33, 38.6), 1.54 mm over copper of Vref, not a plane; other side: none: the signal layer is outermost
- 'NetC49_2' on TOP_LAYER at (9.03, 38.93), 1.47 mm over copper of comp, not a plane; other side: none: the signal layer is outermost
- 'NetC49_2' on TOP_LAYER at (7.48, 37.38), 1.18 mm over copper of comp, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'comp' on TOP_LAYER at (43.8, 42.3), 1.04 mm over copper of ss, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'bias' on TOP_LAYER at (125.4, 31.3), 0.76 mm over copper of Vref, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'cs' on TOP_LAYER at (40.5, 42.05), 0.55 mm over copper of ss, not a plane, to the end of the track; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=void%3Arouted%40PLANE_1%7CTOP_LAYER serves each with its own layer_image region; all of them lie in x 6.48..126.4, y -0.1..44.95 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
- ReferencePlaneDiscontinuitymajorOpen
ReferencePlaneDiscontinuity: 7 boards×7
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: splits, voids and reference changes read from the copper stand; they sit on slow control, protection and sense nets of a ~100 kHz converter, and no datasheet or app note on file sets a limit. Left for the owner.
At along@PLANE_2:GND_I|GND_O, split@PLANE_1:GND_O|Vsense-, split@PLANE_2:GND_I|Vout, split@PLANE_2:GND_O|Vsense-, void:GND_I@PLANE_2:41.75,4.6, void:routed@BOTTOM_LAYER|PLANE_2, void:Vcc@PLANE_1:64.37,48.07
Each finding, with its own headline
along@PLANE_2:GND_I|GND_O'acpl_vo+' runs ALONG the split between the GND_I and GND_O planes on PLANE_2 at 1 place, the longest 23.9 mm; the impedance rises from 43 ohm to 52 ohm there at worst, 9.3 % of each edge reflected (fastest: acpl_vo+ at 100 ps 10-90 %, ASSUMED)
On PLANE_2 the GND_I and GND_O planes part, and 'acpl_vo+' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 43 ohm; along the slot 52 ohm, reflecting up to 9.3 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 54 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'acpl_vo+' on BOTTOM_LAYER at (131.5, 18.95), 25.03 mm, running ALONG the split for 23.9 mm, not across it, 43 ohm over solid plane, 52 ohm along it: 9.3 % of each edge reflected; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=along%40PLANE_2%3AGND_I%7CGND_O serves each with its own layer_image region; all of them lie in x 130.1..132.5, y 5.6..32.3 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PLANE_1:GND_O|Vsense-6 nets cross the split between the GND_O and Vsense- planes on PLANE_1 at 6 places, with no plane on the track's other side (fastest: NetC54_1 at 100 ps 10-90 %, ASSUMED)
On PLANE_1 the GND_O and Vsense- planes part, and 6 nets cross from one to the other at 6 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 6 crossing(s) the track's other neighbour carries a plane, which the return can use there; 6 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'NetC54_1' on TOP_LAYER at (153.64, 46.84), 1.06 mm; other side: none: the signal layer is outermost
- 'NetC56_1' on TOP_LAYER at (145.02, 53.5), 0.48 mm; other side: none: the signal layer is outermost
- 'NetC56_2' on TOP_LAYER at (144.71, 47.86), 0.71 mm; other side: none: the signal layer is outermost
- 'NetIC11_2' on TOP_LAYER at (147.37, 21.87), 0.93 mm; other side: none: the signal layer is outermost
- 'NetIC12_2' on TOP_LAYER at (149.71, 60.88), 0.74 mm; other side: none: the signal layer is outermost
- 'NetR124_1' on TOP_LAYER at (153.44, 49.9), 0.86 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=split%40PLANE_1%3AGND_O%7CVsense- serves each with its own layer_image region; all of them lie in x 143.71..154.87, y 20.54..62.24 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PLANE_2:GND_I|Vout'test_otp2' crosses the split between the GND_I and Vout planes on PLANE_2 at 1 place, with no plane on the track's other side (fastest: test_otp2 at 100 ps 10-90 %, ASSUMED)
On PLANE_2 the GND_I and Vout planes part, and 'test_otp2' crosses from one to the other at 1 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 1 crossing(s) the track's other neighbour carries a plane, which the return can use there; 1 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'test_otp2' on BOTTOM_LAYER at (89.68, 52.05), 11.34 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=split%40PLANE_2%3AGND_I%7CVout serves each with its own layer_image region; all of them lie in x 83.1..93.83, y 47.9..56.2 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PLANE_2:GND_O|Vsense-3 nets cross the split between the GND_O and Vsense- planes on PLANE_2 at 3 places, with no plane on the track's other side (fastest: NetC55_1 at 100 ps 10-90 %, ASSUMED)
On PLANE_2 the GND_O and Vsense- planes part, and 3 nets cross from one to the other at 3 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 3 crossing(s) the track's other neighbour carries a plane, which the return can use there; 3 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'NetC55_1' on BOTTOM_LAYER at (148.31, 59.56), 0.7 mm; other side: none: the signal layer is outermost
- 'va' on BOTTOM_LAYER at (153.45, 23.75), 1.27 mm; other side: none: the signal layer is outermost
- 'vref_o' on BOTTOM_LAYER at (153.45, 39.1), 0.9 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=split%40PLANE_2%3AGND_O%7CVsense- serves each with its own layer_image region; all of them lie in x 147.31..154.9, y 22.3..60.91 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND_I@PLANE_2:41.75,4.6'ipk' crosses where the outline of the GND_I plane on PLANE_2 is drawn back, at 1 place, the longest 51.27 mm (fastest: ipk at 100 ps 10-90 %, ASSUMED)
Along 'ipk' on BOTTOM_LAYER, the GND_I plane on PLANE_2 has 51.27 mm under the track with no copper, at (41.75, 4.6), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 49.9 mm). No hole cleared it: the outline of the pour at x 0.9..131.1, y 5.06..91.19 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'ipk' on BOTTOM_LAYER at (41.75, 4.6), 51.27 mm, running ALONG the bare copper for 49.9 mm, not across it over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=void%3AGND_I%40PLANE_2%3A41.75%2C4.6 serves each with its own layer_image region; all of them lie in x 15.33..68.2, y 3.6..6.1 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:routed@BOTTOM_LAYER|PLANE_23 nets on BOTTOM_LAYER cross the tracks routed through the GND_I pour on PLANE_2 at 3 places, the longest 172.56 mm; 3 run ALONG the cut round another net's track (fastest: acpl_vo+ at 100 ps 10-90 %, ASSUMED)
The GND_I pour on PLANE_2 is cleared round tracks routed through it, and tracks on BOTTOM_LAYER, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 3 place(s) on 3 net(s). 3 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 150.86 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'acpl_vo-' on BOTTOM_LAYER at (51.55, 0.9), 172.56 mm, running ALONG the bare copper for 150.86 mm, not across it over copper of uvlo, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'acpl_vo+' on BOTTOM_LAYER at (47.89, 3.6), 115.97 mm, running ALONG the bare copper for 108.36 mm, not across it over copper of ovp, uvlo, not a plane; other side: none: the signal layer is outermost
- 'csb' on BOTTOM_LAYER at (3.57, 20.02), 8.56 mm, running ALONG the bare copper for 2.91 mm, not across it over copper of ovp, not a plane, to the end of the track; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=void%3Arouted%40BOTTOM_LAYER%7CPLANE_2 serves each with its own layer_image region; all of them lie in x -0.14..133.8, y -0.1..37.4 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:Vcc@PLANE_1:64.37,48.07'otp1' crosses where the outline of the Vcc plane on PLANE_1 is drawn back, at 1 place, the longest 1.45 mm (fastest: otp1 at 100 ps 10-90 %, ASSUMED)
Along 'otp1' on TOP_LAYER, the Vcc plane on PLANE_1 has 1.45 mm under the track with no copper, at (64.37, 48.07), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 2.54..133.1, y 5.08..74.93 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'otp1' on TOP_LAYER at (64.37, 48.07), 1.45 mm over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=void%3AVcc%40PLANE_1%3A64.37%2C48.07 serves each with its own layer_image region; all of them lie in x 62.93..66.02, y 46.63..49.51 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
- SinglePointNetmajorOpen
SinglePointNet: 4 pins×4
4 checked by the review by a reviewer — 4 different reasons
At IC10.5, IC10.6, IC15.5, IC15.6
Each finding, with its own headline
IC10.5IC10.5 (2IN+) is an IC input left unconnected
Pin IC10.5 (2IN+) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.
IC10.6IC10.6 (2IN-) is an IC input left unconnected
Pin IC10.6 (2IN-) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.
IC15.5IC15.5 (IN2+) is an IC input left unconnected
Pin IC15.5 (IN2+) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.
IC15.6IC15.6 (IN2-) is an IC input left unconnected
Pin IC15.6 (IN2-) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.
OVP detector IC9 (LM4041-ADJ) sits at about 12 V cathode-to-anode in normal operation and 14.8 V at trip, above its 10 V range and at its 15 V absolute maximum
The output over-voltage detector IC9 (LM4041DIM3-ADJ) has its cathode on Vout (12 V) and its anode returned through R99 820 R to the HCNR200 IC11 LED, so below the trip it holds about the whole output voltage: about 12 V normally and about 14.8 V just before tripping, against the LM4041-ADJ's 10 V recommended maximum and 15 V absolute maximum. The same OVP circuit on OHWR0047 RATOPUS CONTROL is OBS-489.
Where it is
IC9 pin 2 (cathode) on Vout; FB (pin 1, NetIC9_1) on R90 20k to Vout, R101 220k to GND_O and R104 220k to the test_ovp pad (schematic: 'test_ovp = Test node for OVP (short to gnd_o to simulate over-voltage)'); anode (pin 3) through R99 820 R to IC11 pin 2 (LED, with R107 22k and R93 220 R also on that node), IC11 pin 1 on GND_O.
The LM4041-ADJ regulates 1.233 V from cathode to FB, so it starts to conduct when Vout x R90 / (R90 + R101) = 1.233 V, i.e. Vout = 1.233 x 240 / 20 = 14.8 V (8.0 V with test_ovp grounded). Below that it is off and its cathode-to-anode voltage is about Vout.
The numbers
Quantity Value Source Vout nominal 12 V, 8.33 A, 100 W schematic sheet 1 OVP trip from the divider 14.8 V R90 20k, R101 220k LM4041-ADJ output voltage, recommended 1.24 V to 10 V LM4041 data sheet p5 LM4041-ADJ maximum output voltage, absolute 15 V LM4041 data sheet p5 Once it trips, the current it sinks is set only by R99: about (14.8 V - 1.24 V - 1.6 V HCNR200 LED) / 820 R = 14.6 mA, above the LM4041's 12 mA recommended maximum (20 mA absolute; data sheet p5), and the same as OBS-478 on RATOPUS CONTROL.
The Vout indicator IC2 (same part, cathode on Vout, LD2 via R17) similarly holds up to its 11.3 V threshold before it turns on, slightly above the 10 V range. A detector whose reference is not stacked on the full output (for example an LM4041 or TL431 with its cathode on a divider tap) would stay inside the ratings.
12 V output TVS D11 (SMBJ12A) has a 12 V working standoff, equal to the nominal output
D11 (SMBJ12A) clamps Vout to GND_O beside the output terminal J10, but its 12 V working peak reverse voltage equals the 12 V nominal output, so any positive tolerance, ripple or load-release overshoot puts it above its rated standoff where leakage is unspecified and, towards 13.2 V, it starts to conduct. The same choice on OHWR0048 RATOPUS POWER is OBS-80.
Quantity Value Source Vout nominal 12 V, 8.33 A, 100 W schematic sheet 1 D11 working peak reverse voltage 12 V SMBJ12A data sheet p1 D11 breakdown at 1 mA 13.2 V min / 14.3 V max SMBJ12A data sheet p2 OVP trip (IC9) 14.8 V R90/R101 divider The OVP trips only above D11's breakdown, so D11 rather than the OVP takes any sustained over-voltage between 13.2 and 14.8 V. A part with a standoff above the output's maximum (for example SMBJ13A or SMBJ14A) keeps the clamp out of normal operation.
Large circular silkscreen outlines run across component pads in the control area (R70, C24, R30 and others)
Two large circular arcs on the top silkscreen (TOP_OVERLAY), each tens of millimetres across, sweep through the densely placed control section and print over solder pads: at 53.9 px/mm the lines cross a pad of R70, of C24 and of R30 (region x 44-56 mm, y 40-53 mm), and at 18.8 px/mm they also run through the R80/C25, T13/R85 and J8/TP11 area. Silk printed on a pad can lift the paste and spoil the joint, and fabricators clip it unpredictably. The arcs do not belong to any of the small parts they cross.
Where What the arc crosses Source x 44-56, y 40-53 mm left pad of R70, a pad of C24, left pad of R30 silk + paste render, 53.9 px/mm x 10-90, y 15-65 mm passes through R80/C25, T13/R85, J8/TP11 silk + paste render, 18.8 px/mm Output tantalums C6-C9 (T495 20 V) run at 60 % of rated on the 12 V output, above KEMET's 50 % recommendation
C6-C9 (KEMET T495D686K020, 68 uF / 20 V MnO2 tantalum) sit on the 12 V output (Vout) at 60 % of their rated voltage; KEMET's own T495 guideline recommends at most 50 % up to 85 C (33 % above), so these parts are operated outside the maker's derating.
Operating point vs the maker's guideline
Quantity Value Source Part T495D686K020ATE070, 68 uF, 20 V, MnO2 BOM C6-C9 Rail Vout = 12 V nominal (12 V stage; schematic note "Vout>11.4V") netlist C6-C9 pin 1 on Vout; schematic Applied / rated 12 V / 20 V = 60 % arithmetic Recommended maximum application voltage 50 % of VR at -55 to 85 C, 33 % of VR at 85 to 125 C KEMET T495 datasheet p.19, Recommended Voltage Derating Guidelines Why it matters
MnO2 tantalum failure rate rises steeply with applied voltage, and a failure is typically a short that can ignite. A 12 V output on a low-impedance converter is the case the derating guideline is written for. A 25 V (or higher) part, or a polymer tantalum with its own 80 % category, would bring the bank inside the maker's recommendation.
- ReferencePlaneDiscontinuityminorOpen
23 nets change reference between GND_I and Vcc at 35 vias, none with a reference that continues across (fastest: NetC47_2 at 100 ps 10-90 %, ASSUMED)
At 35 via(s), on 23 net(s), the signal leaves a layer referenced by one of GND_I and Vcc for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 35 served. Every site is served, so the finding is the lower tier (info). 35 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND_I and Vcc are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'acpl_vo-' at (129.2, 38.3), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 176.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'acpl_vo+' at (129.2, 34.8), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 159.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'test_otp2' at (81.3, 55.2), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 149.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'test_otp2' at (97.8, 9.3), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 149.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'test_otp2' at (97.8, 23.2), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 149.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'csb' at (19.48, 34.75), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 140.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'csb' at (99.7, 11.8), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 140.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'csb' at (100.2, 22.9), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 140.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'sd_i' at (110.1, 12.8), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 122.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'otp1' at (59.1, 43.6), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 122.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'ipk' at (70.5, 24.4), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 80.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- 'test_otp1' at (65.6, 14.2), TOP_LAYER -> BOTTOM_LAYER: Vcc on PLANE_1 to GND_I on PLANE_2; pure, no reference continues across; stitching served, 44.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND_I on PLANE_2 and Vcc on PLANE_1 are adjacent, 0.127 mm apart: their own capacitance carries the return. Served.
- and 23 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/51/reference-planes?group=refchange%3AGND_I%7CVcc serves each with its own layer_image region; all of them lie in x 9.07..131.2, y 6..57.2 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
At refchange:GND_I|Vcc
- DecapViaFanoutminorOpen
C43 on 'Vref': its rail pad reaches its via over 2.10 mm of track and its ground pad over 0.00 mm, adding about 0.58 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)
C43 on 'Vref': its rail pad reaches its via over 2.10 mm of track and its ground pad over 0.00 mm, adding about 0.58 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C43.2 (rail) runs 2.10 mm along its copper to its nearest via, 1.10 mm past the 1 mm beside the pad: 0.58 nH; C43.1 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.58 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.76 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.25 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
At C43
- ConnectorDomainMixedminorOpen
ConnectorDomainMixed: 2 components×2
2 checked by the review by Claude walker W1 (Cern session) — 2 different reasons
At J2, J3
Each finding, with its own headline
J2J2 takes 2 different supplies off the board on one connector: Vout (12.0 V), +5V (5.0 V)
J2 carries 2 different supplies out of the board on one connector: Vout (12.0 V) on 1, +5V (5.0 V) on 2. Declare the intent. Two rails on one connector is ordinary in a docking or power-distribution interface and a hazard in a signal one, and the difference is not visible from the netlist — but note that adjacent contacts at different voltages are exactly what a mirrored, reversed or off-by-one cable shorts together, so the cost of getting the mating wrong is a rail collision rather than a dead signal. If this is a standard connector, declare its family (connector_family_declare) and file the standard's contact map: supplies on the contacts it assigns to power are then not reported.
J3J3 takes 4 different supplies off the board on one connector: Vcc2 (10.8 V), Vcc (10.4 V), Vcc1 (10.4 V), Vref (5.0 V)
J3 carries 4 different supplies out of the board on one connector: Vcc2 (10.8 V) on 2, Vcc (10.4 V) on 3, Vcc1 (10.4 V) on 1, Vref (5.0 V) on 4. Declare the intent. Two rails on one connector is ordinary in a docking or power-distribution interface and a hazard in a signal one, and the difference is not visible from the netlist — but note that adjacent contacts at different voltages are exactly what a mirrored, reversed or off-by-one cable shorts together, so the cost of getting the mating wrong is a rail collision rather than a dead signal. If this is a standard connector, declare its family (connector_family_declare) and file the standard's contact map: supplies on the contacts it assigns to power are then not reported.
Main parts
| Part number | Maker | Description | Where |
|---|---|---|---|
| 217-36CTRE6 | WAKEFIELD-VETTE | Heat Sink With 2 pads | HS1 |
| 4N35SR2M | ON SEMICONDUCTOR | Single Optocoupler with Base | IC16 |
| ACPL-C87B-000E | AVAGO TECHNOLOGIES | Precision Optically Isolated Voltage Sensor | IC14 |
| BC807-25 | NXP SEMICONDUCTORS | PNP Transistor | T10 |
| BCP53 | NXP SEMICONDUCTORS | PNP Transistor | T1 |
| BZV55-B11 | NEXPERIA | Zener Diode | D12 |
| BZV55-B12 | NEXPERIA | Zener Diode | D27 |
| BZV55-C2V4 | NEXPERIA | Zener Diode | D24 |
| HCNR200-300E | AVAGO TECHNOLOGIES | High-Linearity Analog Optocoupler | IC11 |
| HCRANQS | CERN | R2E-DCDC ACF Power Transformer [48V; 12V] | TR1 |
| IPB320N20N3GATMA1 | INFINEON | N-CHANNEL MOSFET WITH DIODE | T4 |
| IPD600N25N3 G | INFINEON | N-CHANNEL MOSFET WITH DIODE | T3 |
| L6498D | ST MICROELECTRONICS | High Voltage High and Low-Side 2A Gate Driver | IC7 |
| L78L05ABUTR | ST MICROELECTRONICS | 3-Terminal Regulator 1=OUT 2=GND 3=IN | IC4 |
| LM358AD | TEXAS INSTRUMENTS | Dual Operational Amplifier | IC15 |
| MTLW-104-07-L-D-250 | SAMTEC | Connector 8 Male | J2 |
| PA1005.070QNL | PULSE | SMT Current Sense Transformer | TR2 |
| SF-3812TL350T-2 | BOURNS | Fuse | F1 |
| SMBJ75A | FAIRCHILD SEMICONDUCTOR | Transient Voltage Suppressor Diode (Uni-Directional) | D1 |
| TL2843BDR-8 | TEXAS INSTRUMENTS | High-Performance Current-Mode PWM Controllers, -40°C to 85°C | IC6 |
| TSW-111-23-L-D | SAMTEC | Connector 20 Male | J3 |
| 1755736 (MSTBVA 2,5/2-G-5,08) | PHOENIX CONTACT | Connector 2 Male | J1, J10 |
| B59721A0100A062 | EPCOS / TDK | Thermistor NTC (Positive Temperature Coefficient) | RT1, RT2 |
| BCP56-16 | NXP SEMICONDUCTORS | NPN Transistor | T17, T2 |
| KPH-1608CGCK | KINGBRIGHT | LED Green 1C 2A | LD1, LD2 |
| SMBJ12A | FAIRCHILD SEMICONDUCTOR | Zener Diode | D11, D14 |
| BAT54C | FAIRCHILD SEMICONDUCTOR | Dual Common Cathode Schottky Diodes | D13, D25, D26 |
| ES1D | FAIRCHILD SEMICONDUCTOR | Diode | D20, D3, D5 |
| LM293D | TEXAS INSTRUMENTS | Dual Operational Amplifier | IC10, IC5, IC8 |
| DST3060LC | LITTELFUSE | Dual Common Cathode Diodes | D6, D7, D8, D9 |
| BC817-25 | NXP SEMICONDUCTORS | NPN Transistor | T11, T12, T14, T16, T5 |
| LM4041DIM3-ADJ/NOPB | TEXAS INSTRUMENTS | Precision Reference 1=Adj 2=Cathode 3=Anode | IC12, IC13, IC2, IC3, IC9 |
| MGSF1N02LT1G | ON SEMICONDUCTOR | N-CHANNEL MOSFET WITH DIODE | T15, T6, T7, T8, T9 |
| BAV99 | FAIRCHILD SEMICONDUCTOR | Serial Diode | D10, D15, D16, D19, D21, D22, D23 |
| TSW-101-23-L-D | SAMTEC | Connector 2 Male | J11, J12, J13, J14, J15, J4 and 5 more |
| D01-9922046 | HARWIN | Single Pin Male | TP1, TP10, TP11, TP12, TP13, TP14 and 12 more |
| B41858C9107M000 | TDK | Polarised capacitor | C22 |
| CC0805_22PF_50V_5%_NP0 | GENERIC | Non-polarised capacitor | C46 |
| CC0805_330NF_50V_20%_X5R | GENERIC | Non-polarised capacitor | C42 |
| CC0805_4.7NF_50V_10%_X7R | GENERIC | Non-polarised capacitor | C24 |
About this design
- Design
- RATOPUS STAGE DCDC 12V — OHWR0050 R1
- Designed in
- Altium Designer
- Board
- 4 copper layers, 160 × 100 mm, 310 components, 136 nets
- Licence
- CERN-OHL-W-2.0
- Source
- https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w at commit
aa0f8b805fdf - Attribution
- CERN Open Hardware Repository, project ohwr/project/psu-rad-acdc-230v-12v5v-110w (commit aa0f8b805fdf947458e09c4c64a58de31cbf2940, 2025-04-10). Licence: CERN-OHL-W-2.0. Source: https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
- Reviewed with
- Probe by E# (E-Sharp AB)