Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

RATOPUS STAGE FLYBACK 5V

OHWR0051 · revision R1

RATOPUS STAGE FLYBACK 5V (OHWR0051 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 4-layer board of 80 × 40 mm with 81 components and 42 nets, published under CERN-OHL-W-2.0.

review 89% walked · 8 findings: 6 major · 2 minor (11 items)

Open in the interactive viewerRead the full review

RATOPUS STAGE FLYBACK 5V (OHWR0051 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 8 findings: 6 major · 2 minor (11 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-553majorOpen

    BAT54C went end-of-life (Obsolete)

    Vendor (DigiKey) lifecycle for BAT54C (onsemi's listing) changed from "Active" to "Obsolete" since this board was reviewed. Placed as D6. A sourcing/longevity risk; consider a replacement before production.

  2. concernCON-001majorOpen

    [eol:BAT54C:Obsolete] BAT54C lifecycle changed from "Active" to "Obsolete" since this board was reviewed: OHWR0051 R1 RATOPUS STAGE FLYBACK 5V. A sourcing and longevity risk. Should this be replaced before the next build?

  3. PartLifecyclemajorOpen

    BAT54C on D6: the distributor catalogue reports "Obsolete" for onsemi's BAT54C

    BAT54C on D6: the distributor catalogue reports "Obsolete" for onsemi's BAT54C — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names FAIRCHILD SEMICONDUCTOR, and that is one line with onsemi: ON Semiconductor completed its acquisition of Fairchild Semiconductor on 2016-09-19 and renamed itself onsemi on 2021-08-05. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/BAT54C/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2018-09-30, 2,968 day(s) ago), so this is a substitution rather than a buy. The distributor reports 54,983 left. No approved alternate is recorded for this position.

    At D6

  4. FiducialMissingmajorOpen

    FiducialMissing: 2 boards×2

    2 checked by the review by evaluation@esharp.se — 2 different reasons

    At bottom, top

    Each finding, with its own headline
    • bottomThe bottom side carries 34 SMT component(s) and no fiducial was found on it

      The bottom side carries 34 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='bottom', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

    • topThe top side carries 40 SMT component(s) and no fiducial was found on it

      The top side carries 40 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

  5. PartLifecyclemajorOpen

    LM293D on IC4: the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D

    LM293D on IC4: the distributor catalogue reports "Obsolete" for Texas Instruments's LM293D — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LM293D/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2023-11-03, 1,108 day(s) ago), so this is a substitution rather than a buy. The distributor reports 6,465 left. No approved alternate is recorded for this position.

    At IC4

  6. SinglePointNetmajorOpen

    SinglePointNet: 2 pins×2

    2 checked by the review by a reviewer — 2 different reasons

    At IC4.5, IC4.6

    Each finding, with its own headline
    • IC4.5IC4.5 (2IN+) is an IC input left unconnected

      Pin IC4.5 (2IN+) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

    • IC4.6IC4.6 (2IN-) is an IC input left unconnected

      Pin IC4.6 (2IN-) is an IC INPUT left UNCONNECTED (on the no-connect bucket). Marked no-connect by the designer, but an input normally needs a defined level - confirm it is truly meant to float. If the datasheet defines this input left open (an internal pull, "read as low when left floating", or a tri-level input whose open state is one of its settings), file it on the pin as if_unused (pull_up, pull_down or may_float) with submit_pin_behavior, citing the page, and this finding clears.

  7. observationOBS-515minorOpen

    No fiducials on either side, with SMT parts on both the top and the bottom

    OHWR0051 R1 RATOPUS STAGE FLYBACK 5V has no fiducial on either side (no FTG/FID part, no fiducial pad), although SMT parts are placed on the top (IC1-IC4, T1, D1-D4) and on the bottom (D5-D9, T2, T3). Its sibling stages OHWR0049 and OHWR0050 carry FTG1-FTG3 on the top. A panel may provide global fiducials, but the board data does not.

    SideSMT partsFiducialsSource
    TopIC1-IC4, T1, D1-D4 and passives0ODB++ placement, layer view
    BottomD5-D9, T2, T3 and passives0ODB++ placement
  8. DecapViaFanoutminorOpen

    DecapViaFanout: 2 components×2

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: fan-out lengths read from the copper stand; the 0.5 nH limit is Probe's starting value, not a TL2843 requirement, and no PDN target is stated. Left for the owner.

    At C16, C20

    Each finding, with its own headline
    • C16C16 on 'Vcc': its rail pad reaches its via over 2.04 mm of track, adding about 0.66 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves)

      C16 on 'Vcc': its rail pad reaches its via over 2.04 mm of track, adding about 0.66 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves). C16.2 (rail) runs 2.04 mm along its copper to its nearest via, 1.04 mm past the 1 mm beside the pad: 0.66 nH; C16.1 (ground) not measured: its own track joins it to IC2.5 (0.00 mm) before any via: it serves that pin directly, and its loop does not run through its vias. Each run past the pad as one conductor of a pair 3.00 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.66 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.23 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C20C20 on 'Vcc': its rail pad reaches its via over 2.83 mm of track and its ground pad over 2.49 mm, adding about 2.10 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves)

      C20 on 'Vcc': its rail pad reaches its via over 2.83 mm of track and its ground pad over 2.49 mm, adding about 2.10 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves). C20.2 (rail) runs 2.83 mm along its copper to its nearest via, 1.83 mm past the 1 mm beside the pad: 1.16 nH; C20.1 (ground) runs 2.49 mm along its copper to its nearest via, 1.49 mm past the 1 mm beside the pad: 0.94 nH. Each run past the pad as one conductor of a pair 3.00 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.10 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.23 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.38 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

Main parts

Part numberMakerDescriptionWhere
170uH_5%_RM6CERNCERN 10W Flyback TransformerTR1
4N35SR2MON SEMICONDUCTORSingle Optocoupler with BaseIC3
BAT54CFAIRCHILD SEMICONDUCTORDual Common Cathode Schottky DiodesD6
BC817-25NXP SEMICONDUCTORSNPN TransistorT3
BCP56-16NXP SEMICONDUCTORSNPN TransistorT2
BZV55-B11NEXPERIAZener DiodeD8
D01-9922046HARWINSingle Pin MaleTP2
ES1DFAIRCHILD SEMICONDUCTORDiodeD4
IPD600N25N3 GINFINEONN-CHANNEL MOSFET WITH DIODET1
LM293DTEXAS INSTRUMENTSDual Operational AmplifierIC4
LM4041DIM3-ADJ/NOPBTEXAS INSTRUMENTSPrecision Reference 1=Adj 2=Cathode 3=AnodeIC1
MGSF1N02LT1GON SEMICONDUCTORN-CHANNEL MOSFET WITH DIODET4
SMBJ12AFAIRCHILD SEMICONDUCTORZener DiodeD7
SMBJ75AFAIRCHILD SEMICONDUCTORTransient Voltage Suppressor Diode (Uni-Directional)D1
TL2843BDR-8TEXAS INSTRUMENTSHigh-Performance Current-Mode PWM Controllers, -40°C to 85°CIC2
1755736 (MSTBVA 2,5/2-G-5,08)PHOENIX CONTACTConnector 2 MaleJ1, J2
RBR10BM30AFHROHM SEMICONDUCTORDual Common Cathode Schottky DiodesD2, D3
BAV99FAIRCHILD SEMICONDUCTORSerial DiodeD10, D5, D9
1206CS-221XGECOILCRAFTInductor With CoreL1
B41858C9107M000TDKPolarised capacitorC2
CC0805_1NF_25V_1%_C0GGENERICNon-polarised capacitorC21
CC0805_1NF_50V_10%_X7RGENERICNon-polarised capacitorC11
CC0805_220PF_50V_5%_C0GGENERICNon-polarised capacitorC15
CC0805_22NF_50V_10%_X7RGENERICNon-polarised capacitorC22
CC0805_47PF_50V_5%_NP0GENERICNon-polarised capacitorC10
CC1206_4.7UF_25V_10%_X7RGENERICNon-polarised capacitorC16
CC1210_10UF_25V_10%_X7RGENERICNon-polarised capacitorC4
CC2220_4.7UF_100V_10%_X7RGENERICNon-polarised capacitorC3
CGA5L3X5R1H106K160ABTDKNon-polarised capacitorC14
R0805_0R_JUMPERGENERICResistorR8
R0805_100K_1%_0.125W_100PPMGENERICResistor - 1%R18
R0805_12K_1%_0.125W_100PPMGENERICResistor - 1%R28
R0805_1M_1%_0.125W_100PPMGENERICResistor - 1%R19
R0805_220K_1%_0.125W_100PPMGENERICResistor - 1%R29
R0805_22K_1%_0.125W_100PPMGENERICResistor - 1%R21
R0805_22R_1%_0.125W_100PPMGENERICResistor - 1%R1
R0805_39K_1%_0.125W_100PPMGENERICResistor - 1%R27
R0805_3K3_1%_0.125W_100PPMGENERICResistor - 1%R34
R0805_3K9_1%_0.125W_100PPMGENERICResistor - 1%R33
R0805_470R_1%_0.125W_100PPMGENERICResistor - 1%R31

About this design

Design
RATOPUS STAGE FLYBACK 5V — OHWR0051 R1
Designed in
Altium Designer
Board
4 copper layers, 80 × 40 mm, 81 components, 42 nets
Licence
CERN-OHL-W-2.0
Source
https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w at commit aa0f8b805fdf
Attribution
CERN Open Hardware Repository, project ohwr/project/psu-rad-acdc-230v-12v5v-110w (commit aa0f8b805fdf947458e09c4c64a58de31cbf2940, 2025-04-10). Licence: CERN-OHL-W-2.0. Source: https://gitlab.com/ohwr/project/psu-rad-acdc-230v-12v5v-110w. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)