RF ATT 4CHA
OHWR0055 · revision R1
RF ATT 4CHA (OHWR0055 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 4-layer board of 410.2 × 83.9 mm with 195 components and 122 nets, published under CERN-OHL-S-2.0, CERN-OHL-W-2.0.
review 73% walked · 13 findings: 8 major · 5 minor (33 items)
Open in the interactive viewerRead the full review

Design review
Probe recorded 13 findings: 8 major · 5 minor (33 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.
LD1117 IC1 output has only 100 nF ceramics; datasheet requires 10 uF minimum for stability
LD1117 regulator IC1 (P5V to P3V3) has no bulk output capacitor: every capacitor on P3V3 is 100 nF, and ST states a 10 uF minimum output capacitor for stability.
Quantity Value Source Capacitors on P3V3 C4, C14 to C19, C20A to C20D, all 100 nF 0805 ceramic netlist: net P3V3 Nearest to IC1 C4, about 24 mm away layout Required minimum 10 uF, "needed for stability" LD1117 datasheet, p.1 SN74LV139A outputs sink up to about 14.5-19.4 mA of LED current (at least about 7 mA with worst-case VOL) against a 6 mA recommended IOL at 3.3 V
The channel LEDs LD3A-LD3D pull up to about 14.5-19.4 mA each into the SN74LV139A decoder outputs (IC5A/IC5B), and still about 7-9 mA if the outputs are as weak as their datasheet allows, against TI's 6 mA recommended low-level output current at 3.3 V.
Where it is
- LEDs LD3A-LD3D (564-0100-222F, three green LEDs each) wired anode to P3V3, cathode through 61R9 (R21x to R23x) to the decoder outputs.
- Example, channel A: R21A (LED_40DBA) to NetIC5A_4, R22A (LED_20DBA) to NetIC5A_5, R23A (LED_0DBA) to NetIC5A_7.
- Decoder VCC is P3V3 (pin 16).
The numbers
Quantity Value Source Supply (LED anodes and decoder VCC) P3V3, 3.3 V netlist Series resistor 61R9 (61.9 Ω, 0.1 %) BOM: R21A-R23A Green LED forward voltage about 2.1 to 2.4 V (typical for a green indicator LED; assumed: the only document on file for 564-0100-222F is Dialight's selector guide, which gives no VF) assumption SN74LV139A VOL 0.44 V max at IOL = 6 mA, VCC = 3 V; not specified at higher current SN74LV139A datasheet p.5 Current per lit LED, ideal output (VOL = 0) (3.3 − 2.4) / 61.9 = 14.5 mA to (3.3 − 2.1) / 61.9 = 19.4 mA derived Current with VOL = 0.44 V subtracted (3.3 − 2.4 − 0.44) / 61.9 = 7.4 mA to (3.3 − 2.1 − 0.44) / 61.9 = 12.3 mA derived Current if the output behaves as its worst-case 6 mA point (0.44 V / 6 mA ≈ 73 Ω) 0.9 / (61.9 + 73) = 6.7 mA to 1.2 / 134.9 = 8.9 mA derived Recommended IOL at VCC 3 V to 3.6 V 6 mA max SN74LV139A datasheet p.5 Absolute maximum continuous output current ±25 mA SN74LV139A datasheet p.4 Every case is above the 6 mA recommended maximum; none reaches the 25 mA absolute maximum. The earlier '13-17 mA' did not follow from these values.
Why it matters
Above the recommended IOL the output low level rises and the device runs outside its guaranteed operating conditions; LED brightness and the logic low on shared decoder outputs are not guaranteed. This is an operating-condition violation rather than damage.
Fix: raise the resistors to about 220R (as used for LD1/LD2), which gives (3.3 − 2.1) / 220 ≈ 5.5 mA at most, or buffer the LEDs.
LD1117 IC1 has 1.1 µF directly on its output; ST requires 10 µF minimum for stability
IC1 (LD1117DT33, P5V to P3V3) has only eleven 100 nF X7R capacitors (1.1 µF) on its output net. The two 4.7 µF tantalums C10/C12 sit behind ferrite beads L1/L2 on the FT2232 supply pins, and even counted in, the nominal total (10.5 µF) falls below 10 µF at their −10% tolerance.
Item Value Source Required output capacitance 10 µF minimum LD1117 datasheet p.1 On P3V3 C4, C14-C19, C20A-D: 100 nF X7R netlist, BOM Behind L1 / L2 (BLM21PG221SN1D beads) C10, C12: TPSA475K010 4.7 µF ±10% tantalum netlist, BOM Why it matters
The LD1117's stability depends on its output capacitor. Capacitance reached only through a ferrite bead does not reliably close the loop. Fix: add a 10 µF tantalum at IC1 pin 3.
- DecapViaFanoutmajorOpen
DecapViaFanout: 2 components×2
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: the fan-out lengths are read from the copper and stand. The 0.5 nH limit is Probe's starting value, not a datasheet or app-note requirement for the FT2232HL, LD1117 or relays on these rails; whether it matters depends on each rail's PDN target, which is not stated. Not refutable with a citation; left for the owner.
At C4, C9
Each finding, with its own headline
C4C4 on 'P3V3': its rail pad reaches its via over 1.57 mm of track and its ground pad over 1.64 mm, adding about 0.64 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C4 on 'P3V3': its rail pad reaches its via over 1.57 mm of track and its ground pad over 1.64 mm, adding about 0.64 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C4.2 (rail) runs 1.57 mm along its copper to its nearest via, 0.57 mm past the 1 mm beside the pad: 0.30 nH; C4.1 (ground) runs 1.64 mm along its copper to its nearest via, 0.64 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.64 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.34 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C9C9 on 'P1V8': its rail pad reaches its via over 1.96 mm of track and its ground pad over 1.64 mm, adding about 0.85 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads
C9 on 'P1V8': its rail pad reaches its via over 1.96 mm of track and its ground pad over 1.64 mm, adding about 0.85 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C9.2 (rail) runs 1.96 mm along its copper to its nearest via, 0.96 mm past the 1 mm beside the pad: 0.51 nH; C9.1 (ground) runs 1.64 mm along its copper to its nearest via, 0.64 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.85 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.34 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
- EsdProtectorPlacementmajorOpen
EsdProtectorPlacement: 6 components×6
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: IC3 PRTR5V0U2X sits 72-81 mm from J3/J5 along USB_D_P/USB_D_N, closer to the FT2232HL than to the connectors, and VBUS joins through a 3.2 mm stub; read from the copper and it stands. Raised as OBS-183 for CERN; left for the owner.
At IC3
Each finding, with its own headline
IC3IC3.2 on 'USB_D_P': IC3 joins the line 81.12 mm from J3.3 on a 95.4 mm run to IC2.8
IC3 (PRTR5V0U2X) protects 'USB_D_P' at J3.3. Along the copper: 81.12 mm of track from the contact, 0 via(s) before it, the line runs through its pad (flow-through); the line runs 95.4 mm on to IC2.8; IC3 sits 56.45 mm farther from the contact than the nearest place outside J3.
IC3 joins the line 81.12 mm from J3.3 on a 95.4 mm run to IC2.8: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
IC3IC3.2 on 'USB_D_P': IC3 joins the line 72.09 mm from J5.3 on a 86.37 mm run to IC2.8
IC3 (PRTR5V0U2X) protects 'USB_D_P' at J5.3. Along the copper: 72.09 mm of track from the contact, 0 via(s) before it, the line runs through its pad (flow-through); the line runs 86.37 mm on to IC2.8; IC3 sits 49.77 mm farther from the contact than the nearest place outside J5.
IC3 joins the line 72.09 mm from J5.3 on a 86.37 mm run to IC2.8: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
IC3IC3.3 on 'USB_D_N': IC3 joins the line 81.11 mm from J3.2 on a 94.73 mm run to IC2.7
IC3 (PRTR5V0U2X) protects 'USB_D_N' at J3.2. Along the copper: 81.76 mm of track from the contact, 0 via(s) before it, on a 0.65 mm branch off the line; the line runs 94.73 mm on to IC2.7; IC3 sits 56.7 mm farther from the contact than the nearest place outside J3.
IC3 joins the line 81.11 mm from J3.2 on a 94.73 mm run to IC2.7: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
IC3IC3.3 on 'USB_D_N': IC3 joins the line 74.81 mm from J5.2 on a 88.43 mm run to IC2.7
IC3 (PRTR5V0U2X) protects 'USB_D_N' at J5.2. Along the copper: 75.46 mm of track from the contact, 0 via(s) before it, on a 0.65 mm branch off the line; the line runs 88.43 mm on to IC2.7; IC3 sits 51.14 mm farther from the contact than the nearest place outside J5.
IC3 joins the line 74.81 mm from J5.2 on a 88.43 mm run to IC2.7: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
IC3IC3.4 on 'USB_VBUS': IC3.4 hangs 3.17 mm off the line (limit 1 mm, default
IC3 (PRTR5V0U2X) protects 'USB_VBUS' at J3.1. Along the copper: 95.5 mm of track from the contact, 0 via(s) before it, on a 3.17 mm branch off the line; the line runs 100.83 mm on to D4.2; IC3 sits 55.51 mm farther from the contact than the nearest place outside J3.
IC3.4 hangs 3.17 mm off the line (limit 1 mm, default: no datasheet figure on file): the line carries the strike past it while the clamp is reached through the branch. IC3 joins the line 92.33 mm from J3.1 on a 100.83 mm run to D4.2: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
IC3IC3.4 on 'USB_VBUS': IC3.4 hangs 3.17 mm off the line (limit 1 mm, default
IC3 (PRTR5V0U2X) protects 'USB_VBUS' at J5.1. Along the copper: 84.86 mm of track from the contact, 0 via(s) before it, on a 3.17 mm branch off the line; the line runs 90.19 mm on to D4.2; IC3 sits 54.2 mm farther from the contact than the nearest place outside J5.
IC3.4 hangs 3.17 mm off the line (limit 1 mm, default: no datasheet figure on file): the line carries the strike past it while the clamp is reached through the branch. IC3 joins the line 81.69 mm from J5.1 on a 90.19 mm run to D4.2: nearer the far end than the contact, so the surge travels most of the line before it is clamped.
Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.
- NetCopperSplitmajorOpen
P3V3's copper is in 2 pieces joined only through IC2: C4.2 and IC2.50 are connected only if the part bonds its pins inside
P3V3's copper is in 2 pieces joined only through IC2: C4.2 and IC2.50 are connected only if the part bonds its pins inside. Piece 1: C14.2, C15.2, C16.2, C17.2, C18.2, C19.2, C20A.2, C20B.2 and 32 more pin(s), on TOP_LAYER and BOTTOM_LAYER, 34 drill(s), over (106.95, 170.69) to (407.65, 236.53). Piece 2: C4.2 and IC2.50, on TOP_LAYER and BOTTOM_LAYER, 1 drill(s), over (381.53, 197.92) to (386.24, 199.48). Only IC2 has pins in more than one piece; if those pins are bonded inside the package the net is whole, and if not, the copper leaves it open. A track or a via of the net joining the pieces closes it.
At split:P3V3
- ReferencePlaneDiscontinuitymajorOpen
ReferencePlaneDiscontinuity: 11 boards×11
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: the splits, voids and reference changes are read from the copper and stand as reported. They are layout-practice findings on slow control lines (relay coils, LED and logic nets, OUT0-7) and the FT2232 USB pair; no datasheet or app note on file sets a limit for them on this board, and the impedance excursions reported are 2.5-2.6 %. Not refutable with a citation; left for the owner.
At gap:PWR:hole 165.74,208.52|356.92,208.78, gap:PWR:hole 356.67,208.52|364.02,215.88, gap:PWR:hole 363.77,215.62|455.43,215.88, gap:PWR:hole 368.85,155.93|369.1,185.4, gap:PWR:hole 53.97,208.52|165.99,208.78, gap:PWR:hole 82.46,185.14|369.1,185.4 and 5 more
Each finding, with its own headline
gap:PWR:hole 165.74,208.52|356.92,208.7816 nets cross one gap in PWR's negative-plane field at 16 places, the longest 0.36 mm (fastest: COIL_A_1A at 100 ps 10-90 %, ASSUMED)
Along 'COIL_B_1A' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.36 mm under the track at (339.86, 208.65). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. 16 places on 16 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 165.74..356.92, y 208.52..208.78. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'COIL_A_1A' on BOTTOM_LAYER at (346.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_1B' on BOTTOM_LAYER at (261.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_1C' on BOTTOM_LAYER at (176.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_2A' on BOTTOM_LAYER at (323.66, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_2B' on BOTTOM_LAYER at (238.66, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_1A' on BOTTOM_LAYER at (339.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_1B' on BOTTOM_LAYER at (254.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_1C' on BOTTOM_LAYER at (169.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_2A' on BOTTOM_LAYER at (312.71, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'COIL_B_2B' on BOTTOM_LAYER at (227.71, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_0DBB' on BOTTOM_LAYER at (292.78, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_0DBC' on BOTTOM_LAYER at (207.78, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- and 4 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%20165.74%2C208.52%7C356.92%2C208.78 serves each with its own layer_image region; all of them lie in x 168.73..347.99, y 207.52..209.78 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
gap:PWR:hole 356.67,208.52|364.02,215.88'COIL_A_1A' crosses one gap in PWR's negative-plane field at 1 place, the longest 0.36 mm (fastest: COIL_A_1A at 100 ps 10-90 %, ASSUMED)
Along 'COIL_A_1A' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.36 mm under the track at (356.95, 208.8). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. What cleared it: the hole at x 356.67..364.02, y 208.52..215.88. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'COIL_A_1A' on BOTTOM_LAYER at (356.95, 208.8), 0.36 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%20356.67%2C208.52%7C364.02%2C215.88 serves each with its own layer_image region; all of them lie in x 355.77..358.12, y 207.8..209.8 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
gap:PWR:hole 363.77,215.62|455.43,215.883 nets cross one gap in PWR's negative-plane field at 3 places, the longest 0.25 mm (fastest: LED_0DBA at 100 ps 10-90 %, ASSUMED)
Along 'LED_40DBA' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.25 mm under the track at (379.67, 215.75). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. 3 places on 3 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 363.77..455.43, y 215.62..215.88. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'LED_0DBA' on BOTTOM_LAYER at (376.56, 215.75), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_20DBA' on BOTTOM_LAYER at (377.19, 215.75), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_40DBA' on BOTTOM_LAYER at (379.67, 215.75), 0.25 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%20363.77%2C215.62%7C455.43%2C215.88 serves each with its own layer_image region; all of them lie in x 375.56..380.67, y 214.62..216.88 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
gap:PWR:hole 368.85,155.93|369.1,185.46 nets cross one gap in PWR's negative-plane field at 6 places, the longest 0.36 mm (fastest: OUT2 at 100 ps 10-90 %, ASSUMED)
Along 'OUT6' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.36 mm under the track at (368.98, 177.65). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. 6 places on 6 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 368.85..369.1, y 155.93..185.4. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'OUT2' on BOTTOM_LAYER at (368.98, 182.73), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (368.98, 184), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT4' on BOTTOM_LAYER at (368.98, 180.19), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT5' on BOTTOM_LAYER at (368.98, 181.46), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT6' on BOTTOM_LAYER at (368.98, 177.65), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT7' on BOTTOM_LAYER at (368.98, 178.92), 0.36 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%20368.85%2C155.93%7C369.1%2C185.4 serves each with its own layer_image region; all of them lie in x 367.85..370.1, y 176.52..185.13 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
gap:PWR:hole 53.97,208.52|165.99,208.789 nets cross one gap in PWR's negative-plane field at 9 places, the longest 0.36 mm (fastest: COIL_A_1D at 100 ps 10-90 %, ASSUMED)
Along 'COIL_B_1D' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.36 mm under the track at (84.86, 208.65). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. 9 places on 9 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 53.97..165.99, y 208.52..208.78. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'COIL_A_1D' on BOTTOM_LAYER at (91.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_2C' on BOTTOM_LAYER at (153.66, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_A_2D' on BOTTOM_LAYER at (68.66, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_1D' on BOTTOM_LAYER at (84.86, 208.65), 0.36 mm; other side: none: the signal layer is outermost
- 'COIL_B_2C' on BOTTOM_LAYER at (142.71, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'COIL_B_2D' on BOTTOM_LAYER at (57.71, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_0DBD' on BOTTOM_LAYER at (122.78, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_20DBD' on BOTTOM_LAYER at (123.41, 208.65), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_40DBD' on BOTTOM_LAYER at (124.67, 208.65), 0.25 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%2053.97%2C208.52%7C165.99%2C208.78 serves each with its own layer_image region; all of them lie in x 56.71..154.79, y 207.52..209.78 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
gap:PWR:hole 82.46,185.14|369.1,185.46 nets cross one gap in PWR's negative-plane field at 6 places, the longest 0.36 mm (fastest: OUT2 at 100 ps 10-90 %, ASSUMED)
Along 'OUT2' on BOTTOM_LAYER, PWR is a negative layer (copper everywhere inside the profile), and its field is cleared for 0.36 mm under the track at (293.93, 185.27). The layer does not state the nets either side, so whether this is a split between two planes or a void in one is not said; either way the return current has to go round it. 6 places on 6 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 82.46..369.1, y 185.14..185.4. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'OUT2' on BOTTOM_LAYER at (293.93, 185.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (295.2, 185.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT4' on BOTTOM_LAYER at (209.49, 185.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT5' on BOTTOM_LAYER at (210.76, 185.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT6' on BOTTOM_LAYER at (124.71, 185.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT7' on BOTTOM_LAYER at (125.98, 185.27), 0.36 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=gap%3APWR%3Ahole%2082.46%2C185.14%7C369.1%2C185.4 serves each with its own layer_image region; all of them lie in x 123.58..296.32, y 184.14..186.4 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:GND|P1V89 nets change reference between GND and P1V8 at 9 vias, none with a reference that continues across (fastest: EECS at 100 ps 10-90 %, ASSUMED)
At 9 via(s), on 9 net(s), the signal leaves a layer referenced by one of GND and P1V8 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 9 with none. 9 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P1V8 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'OUT6' at (392.84, 195.7), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 364.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT7' at (394.23, 195.83), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 338.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT4' at (394.87, 194.3), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 272.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT3' at (391.95, 193.29), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 153.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT0' at (394.99, 192.02), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 74.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT1' at (392.84, 192), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 48.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'EEDATA' at (391.82, 197.99), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 19.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'EECLK' at (393.09, 198.11), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 17.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (1 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'EECS' at (394.23, 198.11), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P1V8 on PWR; pure, no reference continues across; stitching none, 14.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P1V8 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=refchange%3AGND%7CP1V8 serves each with its own layer_image region; all of them lie in x 389.82..396.99, y 190..200.11 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:GND|P3V317 nets change reference between GND and P3V3 at 19 vias, none with a reference that continues across (fastest: EECS at 100 ps 10-90 %, ASSUMED)
At 19 via(s), on 17 net(s), the signal leaves a layer referenced by one of GND and P3V3 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 19 with none. 19 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P3V3 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'OUT6' at (112.11, 190.88), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 364.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT7' at (112.11, 192.15), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 338.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT4' at (197.11, 190.88), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 272.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT5' at (197.11, 192.15), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 244.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT5' at (398.55, 195.19), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 244.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C16 (100 nF 0603) 2.6 mm away: 1.20 nH in the 1.000 mm cavity + 0.51 nH ESL + 0.83 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED): 80.1 ohm at the knee, 160 % of 50 ohm (assumed track impedance). None.
- 'OUT2' at (282.11, 190.88), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 176.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT2' at (398.3, 191.76), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 176.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT3' at (282.11, 192.15), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 153.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT0' at (367.11, 190.88), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 74.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT1' at (367.11, 192.15), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 48.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_0DBA' at (374.81, 197.23), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_20DBA' at (374.81, 194.69), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P3V3 on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 7 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=refchange%3AGND%7CP3V3 serves each with its own layer_image region; all of them lie in x 110.11..409.06, y 188.87..199.23 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:GND|P5V30 nets change reference between GND and P5V at 31 vias, none with a reference that continues across (fastest: COIL_A_1A at 100 ps 10-90 %, ASSUMED)
At 31 via(s), on 30 net(s), the signal leaves a layer referenced by one of GND and P5V for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 31 with none. 31 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P5V are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'OUT6' at (70.91, 196.6), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 364.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT7' at (92.91, 196.5), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 338.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT4' at (155.91, 196.6), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 272.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT5' at (177.91, 196.5), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 244.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT2' at (240.91, 196.6), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 176.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT3' at (262.91, 196.5), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 153.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT0' at (325.91, 196.6), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 74.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'OUT1' at (347.91, 196.5), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 48.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_0DBD' at (119.81, 197.23), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_0DBC' at (204.81, 197.23), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_20DBC' at (204.81, 194.69), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'LED_20DBD' at (119.81, 194.69), TOP_LAYER -> BOTTOM_LAYER: GND on GND to P5V on PWR; pure, no reference continues across; stitching none, 40.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P5V are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 19 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=refchange%3AGND%7CP5V serves each with its own layer_image region; all of them lie in x 55.71..371.41, y 192.69..214.1 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PWR:P1V8|P3V39 nets cross the split between the P1V8 and P3V3 planes on PWR at 11 places, with no plane on the track's other side (fastest: EECS at 100 ps 10-90 %, ASSUMED)
On PWR the P1V8 and P3V3 planes part, and 9 nets cross from one to the other at 11 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 11 crossing(s) the track's other neighbour carries a plane, which the return can use there; 11 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'EECLK' on BOTTOM_LAYER at (395.61, 198.84), 0.25 mm; other side: none: the signal layer is outermost
- 'EECS' on BOTTOM_LAYER at (395.61, 197.45), 0.25 mm; other side: none: the signal layer is outermost
- 'EEDATA' on BOTTOM_LAYER at (395.61, 199.3), 0.25 mm; other side: none: the signal layer is outermost
- 'OUT0' on BOTTOM_LAYER at (386.47, 190.13), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT1' on BOTTOM_LAYER at (385.97, 190.63), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (386.98, 189.62), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (395.61, 191.54), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (395.61, 192.47), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT4' on BOTTOM_LAYER at (395.61, 195.04), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT6' on BOTTOM_LAYER at (395.61, 196.97), 0.25 mm; other side: none: the signal layer is outermost
- 'OUT7' on BOTTOM_LAYER at (395.61, 196.45), 0.25 mm; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=split%40PWR%3AP1V8%7CP3V3 serves each with its own layer_image region; all of them lie in x 384.79..396.74, y 188.62..200.3 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PWR:P3V3|P5V14 nets cross the split between the P3V3 and P5V planes on PWR at 14 places, with no plane on the track's other side (fastest: LED_0DBA at 100 ps 10-90 %, ASSUMED)
On PWR the P3V3 and P5V planes part, and 14 nets cross from one to the other at 14 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 14 crossing(s) the track's other neighbour carries a plane, which the return can use there; 14 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'LED_0DBA' on BOTTOM_LAYER at (376.56, 208.77), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_20DBA' on BOTTOM_LAYER at (377.19, 208.77), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_40DBA' on BOTTOM_LAYER at (379.67, 208.77), 0.25 mm; other side: none: the signal layer is outermost
- 'LED_40DBB' on BOTTOM_LAYER at (292.78, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'LED_40DBC' on BOTTOM_LAYER at (207.78, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'LED_40DBD' on BOTTOM_LAYER at (122.78, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT0' on BOTTOM_LAYER at (329.24, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT1' on BOTTOM_LAYER at (351.14, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT2' on BOTTOM_LAYER at (244.24, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT3' on BOTTOM_LAYER at (266.14, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT4' on BOTTOM_LAYER at (159.24, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- 'OUT5' on BOTTOM_LAYER at (181.14, 193.27), 0.36 mm; other side: none: the signal layer is outermost
- and 2 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=split%40PWR%3AP3V3%7CP5V serves each with its own layer_image region; all of them lie in x 73.11..380.67, y 192.14..209.89 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
- PartLifecyclemajorOpen
SN74LV139AD on 4 placements (IC5A, IC5B, IC5C, IC5D): the distributor catalogue reports "Obsolete" for Texas Instruments's SN74LV139AD
SN74LV139AD on 4 placements (IC5A, IC5B, IC5C, IC5D): the distributor catalogue reports "Obsolete" for Texas Instruments's SN74LV139AD — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TEXAS INSTRUMENTS). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/SN74LV139AD/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2024-02-29, 990 day(s) ago), so this is a substitution rather than a buy. The distributor reports 26,438 left. No approved alternate is recorded for this position.
At IC5A
LD1 and LD2 roles are swapped against the schematic note
LD1 and LD2 roles are swapped against the schematic note: the note says LD1 = power, LD2 = activity, but in the netlist LD1 is the programmable LED and LD2 is the always-on power LED.
LED Page 2 note Netlist Source LD1 power driven from FT2232 IC2 pin 26 (ACBUS0) through R11 netlist: component R11 LD2 activity (to be defined by the programmer) tied permanently to P3V3 through R12 netlist: component R12 USB ESD protector IC3 is placed farther from J3 than the FT2232 it protects
USB ESD protector IC3 (PRTR5V0U2X) is placed farther from USB connector J3 than the FT2232 IC2 it protects, so an ESD strike reaches the transceiver pins before the clamp.
Part Role Distance from J3 Source IC3 clamps USB_D_P, USB_D_N, USB_VBUS (pins 2, 3, 4) about 60.6 mm placement IC2 FT2232, the protected transceiver about 45.3 mm placement Channel A transistor designators are ambiguous on the silkscreen, and D1A is printed upside down
In channel A, the relay-driver transistor designators T1A to T8A are printed in pairs below the row, so a reader cannot tell which label belongs to which package, and D1A is printed upside down.
- The SOT-23 transistors T1A to T8A sit in two tight rows.
- Their designators are printed in pairs below the row: for example T7A and T1A side by side, T8A and T2A side by side.
- D1A's designator is rotated 180 degrees relative to D2A, D5A and D6A beside it.
- DecapViaFanoutminorOpen
DecapViaFanout: 4 components×4
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: the fan-out lengths are read from the copper and stand. The 0.5 nH limit is Probe's starting value, not a datasheet or app-note requirement for the FT2232HL, LD1117 or relays on these rails; whether it matters depends on each rail's PDN target, which is not stated. Not refutable with a citation; left for the owner.
At C1, C15, C17, C2
Each finding, with its own headline
C1C1 on 'P1V8': its rail pad reaches its via over 1.54 mm of track and its ground pad over 1.88 mm, adding about 0.86 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves)
C1 on 'P1V8': its rail pad reaches its via over 1.54 mm of track and its ground pad over 1.88 mm, adding about 0.86 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 4.7 uF bulk capacitor: its inductance matters only far above the band it serves). C1.1 (rail) runs 1.54 mm along its copper to its nearest via, 0.54 mm past the 1 mm beside the pad: 0.33 nH; C1.2 (ground) runs 1.88 mm along its copper to its nearest via, 0.88 mm past the 1 mm beside the pad: 0.53 nH. Each run past the pad as one conductor of a pair 2.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.86 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.73 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C15C15 on 'P3V3': its rail pad reaches its via over 1.48 mm of track and its ground pad over 1.66 mm, adding about 0.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)
C15 on 'P3V3': its rail pad reaches its via over 1.48 mm of track and its ground pad over 1.66 mm, adding about 0.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C15.2 (rail) runs 1.48 mm along its copper to its nearest via, 0.48 mm past the 1 mm beside the pad: 0.25 nH; C15.1 (ground) runs 1.66 mm along its copper to its nearest via, 0.66 mm past the 1 mm beside the pad: 0.35 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.60 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.34 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C17C17 on 'P3V3': its rail pad reaches its via over 1.44 mm of track and its ground pad over 1.51 mm, adding about 0.50 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)
C17 on 'P3V3': its rail pad reaches its via over 1.44 mm of track and its ground pad over 1.51 mm, adding about 0.50 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C17.2 (rail) runs 1.44 mm along its copper to its nearest via, 0.44 mm past the 1 mm beside the pad: 0.23 nH; C17.1 (ground) runs 1.51 mm along its copper to its nearest via, 0.51 mm past the 1 mm beside the pad: 0.27 nH. Each run past the pad as one conductor of a pair 1.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.50 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.34 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
C2C2 on 'P5V': its ground pad over 1.82 mm, adding about 0.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves)
C2 on 'P5V': its ground pad over 1.82 mm, adding about 0.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 47 uF bulk capacitor: its inductance matters only far above the band it serves). C2.1 (rail) not measured: its own track joins it to IC1.2 (3.87 mm) before any via: it serves that pin directly, and its loop does not run through its vias; C2.2 (ground) runs 1.82 mm along its copper to its nearest via, 0.82 mm past the 1 mm beside the pad: 0.60 nH. Each run past the pad as one conductor of a pair 4.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.60 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.93 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.22 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.
- ReferencePlaneDiscontinuityminorOpen
ReferencePlaneDiscontinuity: 2 boards×2
Checked by the review, stands · Claude walker W1 (Cern session) — Checked: the splits, voids and reference changes are read from the copper and stand as reported. They are layout-practice findings on slow control lines (relay coils, LED and logic nets, OUT0-7) and the FT2232 USB pair; no datasheet or app note on file sets a limit for them on this board, and the impedance excursions reported are 2.5-2.6 %. Not refutable with a citation; left for the owner.
At along@PWR:P1V8|P3V3, along@PWR:P3V3|P5V
Each finding, with its own headline
along@PWR:P1V8|P3V3'OUT2' runs ALONG the split between the P1V8 and P3V3 planes on PWR at 1 place, the longest 2.15 mm; the impedance rises from 51 ohm to 54 ohm there at worst, 2.6 % of each edge reflected (fastest: OUT2 at 100 ps 10-90 %, ASSUMED)
On PWR the P1V8 and P3V3 planes part, and 'OUT2' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 51 ohm; along the slot 54 ohm, reflecting up to 2.6 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 97 ohm). At every place the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is the lower tier (info). One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'OUT2' on BOTTOM_LAYER at (391.15, 186.54), 2.8 mm, running ALONG the split for 2.15 mm, not across it, 51 ohm over solid plane, 54 ohm along it: 2.6 % of each edge reflected; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=along%40PWR%3AP1V8%7CP3V3 serves each with its own layer_image region; all of them lie in x 388.88..393.68, y 185.54..187.54 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@PWR:P3V3|P5V'COIL_A_1A' runs ALONG the split between the P3V3 and P5V planes on PWR at 1 place, the longest 0.47 mm; the impedance rises from 55 ohm to 58 ohm there at worst, 2.5 % of each edge reflected (fastest: COIL_A_1A at 100 ps 10-90 %, ASSUMED)
On PWR the P3V3 and P5V planes part, and 'COIL_A_1A' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 55 ohm; along the slot 58 ohm, reflecting up to 2.5 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 102 ohm). At every place the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is the lower tier (info). One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'COIL_A_1A' on BOTTOM_LAYER at (367.95, 208.8), 0.88 mm, running ALONG the split for 0.47 mm, not across it, 55 ohm over solid plane, 58 ohm along it: 2.5 % of each edge reflected; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/56/reference-planes?group=along%40PWR%3AP3V3%7CP5V serves each with its own layer_image region; all of them lie in x 366.56..369.4, y 207.8..209.89 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
Main parts
| Part number | Maker | Description | Where |
|---|---|---|---|
| 22-27-2051 | MOLEX | Connector 5 Male | J5 |
| 93C46B-I/SN | MICROCHIP TECHNOLOGY | 1Kbit, 5V, MICROWIRE® Serial EEPROM With 16-Bit Organization | IC4 |
| A-USBSB | ASSMANN | 4 Pin + 1 Shield USB Receptacle | J3 |
| ABM3B-12.000MHZ-B2-T | ABRACON | Crystal 4 pins 1=XTAL Control 2=GND3=XTAL 4=GND | Q1 |
| FT2232HL | FUTURE TECHNOLOGY DEVICES INTERNATIONAL (FTDI) | Dual High Speed USB to Multipurpose UART/FIFO IC | IC2 |
| LD1117DT33CTR | ST MICROELECTRONICS | 3-Terminal Regulator 1=GND 2=IN 3=OUT | IC1 |
| PRTR5V0U2X | NXP SEMICONDUCTORS | Ultra Low Capacitance Double Rail-to-Rail ESD Protection Diode | IC3 |
| S2B-PH-SM4-TB | JST (JAPAN SOLDERLESS TERMINALS) | Connector 2 Male | J4 |
| 555-2303F | DIALIGHT | LED Green 1C 2A | LD1, LD2 |
| 564-0100-222F | DIALIGHT | LED x3 Green LED | LD3A, LD3B, LD3C, LD3D |
| SN74LV139AD | TEXAS INSTRUMENTS | Dual 2-to-4 line decoder/demultiplexer | IC5A, IC5B, IC5C, IC5D |
| 132203 | AMPHENOL | J1A, J1B, J1C, J1D, J2A, J2B, J2C, J2D | |
| 46-0014S | DICONEX | 2GHz, 3W, 50 Ohm, 20dB, SMD Attenuator | IC6A, IC6B, IC6C, IC6D, IC7A, IC7B, IC7C, IC7D |
| BSH103 | NEXPERIA | N-CHANNEL MOSFET WITH DIODE | T5A, T5B, T5C, T5D, T6A, T6B and 10 more |
| BSH203 | NXP SEMICONDUCTORS | P-CHANNEL MOSFET WITH DIODE | T1A, T1B, T1C, T1D, T2A, T2B and 10 more |
| HF3 53 or 1462051-2 | TYCO AXICOM | SMD SPDT RF Signal Relays (Monostable 1 Coil) | RL1A, RL1B, RL1C, RL1D, RL2A, RL2B and 10 more |
| SS16 | VISHAY GENERAL SEMICONDUCTOR | Schottky Diode | D1A, D1B, D1C, D1D, D2A, D2B and 12 more |
| CTE6032-28_47UF_10V_10% | GENERIC | Polarised capacitor | C2 |
| R0805_1K_1%_0.125W_100PPM | GENERIC | Resistor - 1% | R10 |
| R0805_2K2_1%_0.125W_100PPM | GENERIC | Resistor - 1% | R16 |
| BLM21PG221SN1D | MURATA | L1, L2 | |
| CC0805_27PF_50V_1%_NP0 | GENERIC | Non-polarised capacitor | C5, C6 |
| R0805_220R_1%_0.125W_100PPM | GENERIC | Resistor - 1% | R11, R12 |
| TPSA475K010T1400 | AVX | Polarised capacitor | C1, C10, C12 |
| R0805_61R9_0.1%_0.1W_10PPM | GENERIC | Resistor - 0.1% | R21A, R21B, R21C, R21D, R22A, R22B and 6 more |
| R0805_12K_1%_0.125W_100PPM | GENERIC | Resistor - 1% | R13, R14, R15, R1A, R1B, R1C and 22 more |
| CC0805_100NF_50V_10%_X7R | GENERIC | Non-polarised capacitor | C11, C13, C14, C15, C16, C17 and 27 more |
About this design
- Design
- RF ATT 4CHA — OHWR0055 R1
- Designed in
- Altium Designer
- Board
- 4 copper layers, 410.2 × 83.9 mm, 195 components, 122 nets
- Licence
- CERN-OHL-S-2.0, CERN-OHL-W-2.0
- Source
- https://gitlab.com/ohwr/project/rf-att-4cha at commit
9ea0095479ba - Attribution
- CERN Open Hardware Repository, project ohwr/project/rf-att-4cha (commit 9ea0095479ba013889bf582ab91eddded12c3bdd, 2025-04-10). Licence: CERN-OHL-S-2.0, CERN-OHL-W-2.0. Source: https://gitlab.com/ohwr/project/rf-att-4cha. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
- Reviewed with
- Probe by E# (E-Sharp AB)