Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

SPEC TICKS

OHWR0045 · revision R1

SPEC TICKS (OHWR0045 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 6-layer board of 164 × 60 mm with 251 components and 187 nets, published under CERN-OHL-1.1.

review 86% walked · 23 findings: 2 blocker · 11 major · 10 minor (59 items)

Open in the interactive viewerRead the full review

SPEC TICKS (OHWR0045 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 23 findings: 2 blocker · 11 major · 10 minor (59 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-167blockerOpen

    u2 and u3 (TLV1117 1.8 V and 2.5 V LDOs) are wired to an IN/GND/OUT pinout; the TI TLV1117 SOT-223 is ADJ/GND, OUTPUT, INPUT with OUTPUT on the tab

    u2 and u3, valued as TLV1117 1.8 V and 2.5 V LDOs, are wired IN/GND/OUT with the tab on GND; with a TLV1117 fitted, both outputs short to GND, 3.3 V drives its ground pin, and neither P1V8 nor P2V5 is produced.

    Pin by pin

    u2 (value tlv11711v8) and u3 (value tlv11712V5) use an SOT-223 footprint. The schematic symbol tlv117118 (sheet 15 of 17) labels pin 1 in, pin 3 out, pins 2 and 4 gnd.

    PadBoard net, u2 / u3TI TLV1117 SOT-223 (DCY) pinWith a TLV1117-18 / -25 fitted
    13.3 V input: NetC306_2 via L24 / NetC304_2 via L25ADJ/GNDground pin sits on 3.3 V
    2GNDOUTPUToutput shorted to GND
    3P1V8 / P2V5INPUTinput pin is the 1.8 V / 2.5 V rail
    4 (tab)GNDOUTPUToutput shorted to GND

    Sources: netlist (u2, u3 pads); TLV1117 datasheet p.3, pin table and Figure 4-1 (DCY package, top view); schematic sheet 15.

    Why it matters

    • P2V5 is the FPGA's VCCAUX and bank 0/2 VCCO.
    • P1V8 feeds bank 1 and the TPS74401 that makes the DDR3 1.5 V rail.

    So with a TLV1117 fitted neither rail is produced, the 3.3 V supply is driven into the regulator's ground pin, and the board cannot configure.

    What would close it

    The symbol's pin order matches 78xx-style IN-GND-OUT, tab GND regulators, not any 1117. Either the fitted part is not a TLV1117 (and the BOM/value should name the real part), or the symbol and footprint pin map must be corrected to TLV1117 order (1 GND, 2 OUT, 3 IN, tab OUT) and the layout rerouted. This was held as an open design question from the pin-table work; the netlist, the symbol and the TI table together settle it.

  2. NetCopperSplitblockerOpen

    P3V3_CLEAN's copper is in 15 pieces: C15.2 and OSC2.6 and 13 other piece(s) are not connected to the rest of the net

    P3V3_CLEAN's copper is in 15 pieces: C15.2 and OSC2.6 and 13 other piece(s) are not connected to the rest of the net. Piece 1: C468.2, C92.2, IC1.1 and IC1.3, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 2 drill(s), over (160.64, 288.71) to (164.11, 293.74). Piece 2: C15.2 and OSC2.6, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 2 drill(s), over (164.68, 293.9) to (166.55, 296.54). Piece 3: C219.2 and IC7.1, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (166.89, 296.92) to (169.25, 297.92). Piece 4: C9.2 and IC3.1, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (167.06, 300.05) to (169.16, 301.05). Piece 5: C34.2 and IC6.20, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (188.59, 293.86) to (190.32, 294.81). Piece 6: C14.2 and IC6.27, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (190.65, 290.52) to (191.6, 292.29). Piece 7: C584.2 and IC6.9, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (193.58, 296.07) to (195.13, 298.1). Piece 8: C220.2 and IC6.1, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (193.69, 291.21) to (194.88, 293.37). Piece 9: C21.2 and IC6.7, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (193.98, 294.23) to (198.75, 296.33). Piece 10: C91.2 and L3.2, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 2 drill(s), over (195.28, 294.95) to (197.6, 298.92). Piece 11: OSC2.2, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (162.18, 298.74) to (163.98, 301.35). Piece 12: L21.2, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 2 drill(s), over (185.17, 295.42) to (186.32, 298.46). Piece 13: IC6.30, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (192.41, 290.15) to (193.01, 292.07). Piece 14: IC6.4, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (193.98, 293.52) to (195.4, 294.12). Piece 15: R36.1, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (173.36, 293.26) to (175.99, 294.61). The export files every one of these pins under the net, so every connectivity check passes; the copper the fab builds leaves them apart. Usually a pour island that touches only one via of its own net, or a track ending short of its copper: join the piece to the net and export again.

    At split:P3V3_CLEAN

  3. observationOBS-168majorOpen

    FMC connector J4 has no power, VREF, I2C, JTAG, PG or PRSNT pins connected: only the LA pairs, CLK0 and ground

    FMC connector J4 connects only the LA00-LA30 pairs, CLK0_M2C and GND; every supply and management pin is unconnected, so a standard mezzanine would get no power and could not be detected.

    Where it is

    J4 is a Samtec ASP-134603-01, the carrier-side VITA 57 LPC connector, as on the SPEC carrier this sheet was copied from (sheet 3 of 17 'FMC Connector', title block EDA-02189-V4-0 'Simple PCIe Carrier Board'). Of its 160 contacts only rows c/d/g/h carry LAxx_P/N, CLK0_M2C_P/N (h4, h5) and GND.

    Unconnected in the netlist:

    • supply pins 3P3V, 12P0V, 3P3VAUX and VADJ
    • VREF_A_M2C
    • the management I2C pair
    • the JTAG pins
    • PG_C2M / PG_M2C
    • PRSNT_M2C

    The FPGA's VREF_A_M2C net (IC2 VREF balls with C345, C60, C61, C62) therefore has no source.

    Why it matters

    A standard FMC mezzanine plugged into J4 would receive no power and could not be detected or identified, so the slot only works with a self-powered partner designed for this board. If that is the intent it should be stated on the drawing; if the board is meant to host FMC mezzanines, the supply and management pins must be connected. The floating VREF_A_M2C is harmless only while no bank-2 I/O uses a VREF-referenced standard.

  4. observationOBS-170majorOpen

    IC10 LM336-2.5 has ADJ shorted to its anode (GND); the datasheet shows ADJ open or trimmed, so the 2.5 V DAC reference is in no documented configuration

    IC10 (LM336M-2.5) has its ADJ pin 5 wired straight to ANODE pin 4 and GND, a configuration the datasheet does not specify, so the 2.5 V VREF for DACs IC3 and IC7 is not in a documented configuration.

    Where it is

    ``mermaid flowchart LR P["P3V3_CLEAN"] --> R36["R36 240R"] --> K["IC10 pin 8 CATHODE<br/>NetC10_2 = VREF"] K --> DAC["IC3, IC7 AD5662<br/>VREF"] K --> C["C10 100nF, C12 22uF"] ADJ["IC10 pin 5 ADJ"] -- "wired directly" --> G["IC10 pin 4 ANODE = GND"] ``

    Shown on schematic sheet 1 and in the netlist: pins 5 and 4 are both on GND.

    What the datasheet shows

    • Plain 2.5 V reference (Figure 5): ADJ not connected.
    • Trimming (Figure 4): a 10 kOhm pot between cathode and anode feeding ADJ.
    • It does not specify the reference voltage with ADJ shorted to the anode.

    Why it matters

    The ADJ pin feeds the internal divider, so shorting it to the anode is expected to move VZ away from 2.5 V; the DAC full scale then follows. The designer should confirm whether ADJ was meant to be left open.

  5. CapVoltageDeratingmajorOpen

    CapVoltageDerating: 2 components×2

    Checked by the review, stands · Claude walker (cern session) — Stands: C300 (u1 input node NetC300_2) and C301 (P24V) are 2.2 uF with BOM description 'Capacitor, LibRef Cap Semi' and no voltage rating; schematic sheet 9 prints only '2.2uF'. The rating cannot be compared with the rail from the design data.

    At C300, C301

    Each finding, with its own headline
    • C300C300 sits on a 12 V rail and its voltage rating is not in the BOM

      C300: on a 12 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source.

    • C301C301 sits on a 12 V rail and its voltage rating is not in the BOM

      C301: on a 12 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source.

  6. DecapViaFanoutmajorOpen

    DecapViaFanout: 12 components×12

    12 checked by the review by Claude walker W1 (Cern session) — 12 different reasons

    At C166, C169, C170, C178, C194, C195 and 6 more

    Each finding, with its own headline
    • C166C166 on 'P3V3': its rail pad reaches its via over 2.56 mm of track and its ground pad over 2.86 mm, adding about 1.73 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C166 on 'P3V3': its rail pad reaches its via over 2.56 mm of track and its ground pad over 2.86 mm, adding about 1.73 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C166.2 (rail) runs 2.56 mm along its copper to its nearest via, 1.56 mm past the 1 mm beside the pad: 0.79 nH; C166.1 (ground) runs 2.86 mm along its copper to its nearest via, 1.86 mm past the 1 mm beside the pad: 0.94 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.73 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.52 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.52 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C169C169 on 'P2V5': its rail pad reaches its via over 3.70 mm of track, adding about 1.37 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C169 on 'P2V5': its rail pad reaches its via over 3.70 mm of track, adding about 1.37 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C169.2 (rail) runs 3.70 mm along its copper to its nearest via, 2.70 mm past the 1 mm beside the pad: 1.37 nH; C169.1 (ground) not measured: its own track joins it to IC2.AA5 (1.20 mm) before any via: it serves that pin directly, and its loop does not run through its vias. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.37 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C170C170 on 'P1V2': its rail pad reaches its via over 6.00 mm of track and its ground pad over 2.02 mm, adding about 3.05 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C170 on 'P1V2': its rail pad reaches its via over 6.00 mm of track and its ground pad over 2.02 mm, adding about 3.05 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C170.2 (rail) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 2.53 nH; C170.1 (ground) runs 2.02 mm along its copper to its nearest via, 1.02 mm past the 1 mm beside the pad: 0.52 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 3.05 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C178C178 on 'P1V2': its rail pad reaches its via over 2.72 mm of track and its ground pad over 0.00 mm, adding about 0.87 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C178 on 'P1V2': its rail pad reaches its via over 2.72 mm of track and its ground pad over 0.00 mm, adding about 0.87 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C178.2 (rail) runs 2.72 mm along its copper to its nearest via, 1.72 mm past the 1 mm beside the pad: 0.87 nH; C178.1 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.87 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C194C194 on 'P1V2': its rail pad reaches its via over 4.15 mm of track and its ground pad over 0.00 mm, adding about 1.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C194 on 'P1V2': its rail pad reaches its via over 4.15 mm of track and its ground pad over 0.00 mm, adding about 1.60 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C194.2 (rail) runs 4.15 mm along its copper to its nearest via, 3.15 mm past the 1 mm beside the pad: 1.60 nH; C194.1 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.60 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C195C195 on 'P3V3': its rail pad reaches its via over 1.17 mm of track and its ground pad over 4.93 mm, adding about 2.08 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C195 on 'P3V3': its rail pad reaches its via over 1.17 mm of track and its ground pad over 4.93 mm, adding about 2.08 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C195.2 (rail) runs 1.17 mm along its copper to its nearest via, 0.17 mm past the 1 mm beside the pad: 0.09 nH; C195.1 (ground) runs 4.93 mm along its copper to its nearest via, 3.93 mm past the 1 mm beside the pad: 1.99 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.08 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C197C197 on 'P1V2': its rail pad reaches its via over 5.39 mm of track, adding about 1.72 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C197 on 'P1V2': its rail pad reaches its via over 5.39 mm of track, adding about 1.72 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C197.1 (rail) runs 5.39 mm along its copper to its nearest via, 4.39 mm past the 1 mm beside the pad: 1.72 nH; C197.2 (ground) not measured: its own track joins it to IC2.N9 (1.44 mm) before any via: it serves that pin directly, and its loop does not run through its vias. Each run past the pad as one conductor of a pair 0.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.72 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.41 nH (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C202C202 on 'P2V5': its rail pad reaches its via over 6.00 mm of track and its ground pad over 0.86 mm, adding about 2.53 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C202 on 'P2V5': its rail pad reaches its via over 6.00 mm of track and its ground pad over 0.86 mm, adding about 2.53 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C202.2 (rail) runs at least 6.00 mm along its copper to its nearest via, 5.00 mm past the 1 mm beside the pad: 2.53 nH; C202.1 (ground) runs 0.86 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 2.53 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.65 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C255C255 on 'P3V3': its rail pad reaches its via over 4.70 mm of track, adding about 1.92 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C255 on 'P3V3': its rail pad reaches its via over 4.70 mm of track, adding about 1.92 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C255.2 (rail) runs 4.70 mm along its copper to its nearest via, 3.70 mm past the 1 mm beside the pad: 1.92 nH; C255.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.70 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.92 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.52 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.52 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C256C256 on 'P3V3': its rail pad reaches its via over 3.17 mm of track, adding about 1.13 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C256 on 'P3V3': its rail pad reaches its via over 3.17 mm of track, adding about 1.13 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C256.2 (rail) runs 3.17 mm along its copper to its nearest via, 2.17 mm past the 1 mm beside the pad: 1.13 nH; C256.1 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.70 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.13 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.52 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.52 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C305C305 on 'P2V5': its ground pad over 4.63 mm, adding about 1.96 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C305 on 'P2V5': its ground pad over 4.63 mm, adding about 1.96 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C305.2 (rail) not measured: its own track joins it to u3.3 (5.69 mm) before any via: it serves that pin directly, and its loop does not run through its vias; C305.1 (ground) runs 4.63 mm along its copper to its nearest via, 3.63 mm past the 1 mm beside the pad: 1.96 nH. Each run past the pad as one conductor of a pair 1.90 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.96 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.52 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.52 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C581C581 on 'P3V3': its rail pad reaches its via over 1.25 mm of track and its ground pad over 4.63 mm, adding about 1.97 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C581 on 'P3V3': its rail pad reaches its via over 1.25 mm of track and its ground pad over 4.63 mm, adding about 1.97 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C581.1 (rail) runs 1.25 mm along its copper to its nearest via, 0.25 mm past the 1 mm beside the pad: 0.13 nH; C581.2 (ground) runs 4.63 mm along its copper to its nearest via, 3.63 mm past the 1 mm beside the pad: 1.84 nH. Each run past the pad as one conductor of a pair 1.60 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.97 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.52 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.52 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  7. EsdProtectorPlacementmajorOpen

    EsdProtectorPlacement: 3 components×3

    e.g. “IC22.2 on 'NetIC21_5': 1 via(s) between J8.2 and IC22.2” · 3 different statements

    At IC22

    Each finding, with its own headline
    • IC22IC22.2 on 'NetIC21_5': 1 via(s) between J8.2 and IC22.2

      IC22 (PRTR5V0U2X) protects 'NetIC21_5' at J8.2. Along the copper: 10.36 mm of track from the contact, 1 via(s) before it, on a 10.36 mm branch off the line; the line runs 0 mm on to IC21.5; IC22 sits 2.13 mm farther from the contact than the nearest place outside J8.

      1 via(s) between J8.2 and IC22.2: the strike reaches an inner layer before it is clamped. IC22.2 hangs 10.36 mm off the line (limit 1 mm, default: no datasheet figure on file): the line carries the strike past it while the clamp is reached through the branch.

      Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.

    • IC22IC22.3 on 'NetIC21_4': 1 via(s) between J8.3 and IC22.3

      IC22 (PRTR5V0U2X) protects 'NetIC21_4' at J8.3. Along the copper: 29.04 mm of track from the contact, 1 via(s) before it, on a 4.05 mm branch off the line; the line runs 29.88 mm on to IC21.4; IC22 sits 1.86 mm farther from the contact than the nearest place outside J8.

      1 via(s) between J8.3 and IC22.3: the strike reaches an inner layer before it is clamped. IC22.3 hangs 4.05 mm off the line (limit 1 mm, default: no datasheet figure on file): the line carries the strike past it while the clamp is reached through the branch. IC22 joins the line 24.99 mm from J8.3 on a 29.88 mm run to IC21.4: nearer the far end than the contact, so the surge travels most of the line before it is clamped.

      Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.

    • IC22IC22.4 on 'NetC201_1': 1 via(s) between J8.1 and IC22.4

      IC22 (PRTR5V0U2X) protects 'NetC201_1' at J8.1. Along the copper: 10.35 mm of track from the contact, 1 via(s) before it, on a 2.87 mm branch off the line; the line runs 7.48 mm on to C201.1; IC22 sits 2.53 mm farther from the contact than the nearest place outside J8.

      1 via(s) between J8.1 and IC22.4: the strike reaches an inner layer before it is clamped. IC22.4 hangs 2.87 mm off the line (limit 1 mm, default: no datasheet figure on file): the line carries the strike past it while the clamp is reached through the branch. IC22 joins the line 7.48 mm from J8.1 on a 7.48 mm run to C201.1: nearer the far end than the contact, so the surge travels most of the line before it is clamped.

      Measured on the copper the ODB states: tracks, the pads they land on, and the netlist's vias. Not a straight line between centroids.

  8. FiducialMissingmajorOpen

    FiducialMissing: 2 boards×2

    Checked by the review, stands · Claude walker (cern session) — Stands: no FID/FTG component on either side (component list); the only fiducial marks are the two local ones inside the IC2 BGA footprint, as recorded in OBS-178.

    At bottom, top

    Each finding, with its own headline
    • bottomThe bottom side carries 157 SMT component(s) and no fiducial was found on it

      The bottom side carries 157 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='bottom', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

    • topThe top side carries 89 SMT component(s) and no fiducial was found on it

      The top side carries 89 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

  9. DecapOrdermajorOpen

    IC2 supply pins AA11, AA15, AA7, V6, W5 on 'P2V5': the smallest capacitor C155 sits 3.3 mm away, behind C149 at 1.2 mm

    IC2 supply pins AA11, AA15, AA7, V6, W5 on 'P2V5': the smallest capacitor C155 sits 3.3 mm away, behind C149 at 1.2 mm. IC2.AA11: the smallest value, C155 (100 nF), is 3.3 mm from the pin and C149 (1 uF) 1.2 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. IC2.AA15: the smallest value, C121 (10 nF), is 4.4 mm from the pin and C231 (100 nF) 1.3 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. IC2.AA7: the smallest value, C169 (10 nF), is 4.1 mm from the pin and C151 (1 uF) 1.5 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. IC2.V6: the smallest value, C169 (10 nF), is 4.1 mm from the pin and C236 (100 nF) 0.2 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. IC2.W5: the smallest value, C169 (10 nF), is 2.7 mm from the pin and C147 (100 nF) 0.6 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. Swap them, or bring the smallest value to the pin: it serves the fastest current and is the one the loop inductance defeats. Distances are pad centre to pin centre in the board plane. The 5 mm radius, the 10x value step and the 1 mm / 1.5x tie tolerance are Probe's starting values.

    At IC2

  10. PartLifecyclemajorOpen

    LP5951MF-3.0/NOPB on IC1: the distributor catalogue reports "Obsolete" for National Semiconductor's LP5951MF-3.0/NOPB

    LP5951MF-3.0/NOPB on IC1: the distributor catalogue reports "Obsolete" for National Semiconductor's LP5951MF-3.0/NOPB — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LP5951MF-3.0/NOPB/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    At IC1

  11. NetCopperSplitmajorOpen

    NetCopperSplit: 3 boards×3

    e.g. “GND's copper is in 3 pieces joined only through IC2 and J4: IC2.V10 and 1 other piece(s) are connected only if the part bonds its pins inside” · 3 different statements

    At split:GND, split:P1V2, split:P2V5

    Each finding, with its own headline
    • split:GNDGND's copper is in 3 pieces joined only through IC2 and J4: IC2.V10 and 1 other piece(s) are connected only if the part bonds its pins inside

      GND's copper is in 3 pieces joined only through IC2 and J4: IC2.V10 and 1 other piece(s) are connected only if the part bonds its pins inside. Piece 1: C1.2, C10.1, C11.1, C12.1, C120.1, C121.1, C122.1, C123.1 and 351 more pin(s), on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 141 drill(s), 9943.78 mm2 of pour, over (103.4, 243.41) to (266.19, 302.63). Piece 2: IC2.V10, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (153.7, 273) to (154.66, 273.95). Piece 3: J4.c8, on TOP_LAYER, over (130.37, 288.47) to (131.01, 289.11). Only IC2 and J4 has pins in more than one piece; if those pins are bonded inside the package the net is whole, and if not, the copper leaves it open. A track or a via of the net joining the pieces closes it.

    • split:P1V2P1V2's copper is in 6 pieces joined only through IC2: C140.1, C159.2, C170.2, C178.2, C188.2, C190.2, C194.2, C203.1 and 8 more pin(s) and 4 other piece(s) are connected only if the part bonds its pins inside

      P1V2's copper is in 6 pieces joined only through IC2: C140.1, C159.2, C170.2, C178.2, C188.2, C190.2, C194.2, C203.1 and 8 more pin(s) and 4 other piece(s) are connected only if the part bonds its pins inside. Piece 1: C183.2, C184.2, C185.2, C186.2, C187.2, C189.2, C192.2, C198.1 and 15 more pin(s), on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 4 drill(s), 12.3 mm2 of pour, over (157.38, 268.12) to (163.66, 274.6). Piece 2: C140.1, C159.2, C170.2, C178.2, C188.2, C190.2, C194.2, C203.1 and 8 more pin(s), on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 5 drill(s), over (133.99, 243.9) to (212.13, 279.55). Piece 3: C196.1, C197.1, C212.1 and IC2.M9, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (157.77, 273.79) to (161.71, 276.59). Piece 4: C191.2 and IC2.N14, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (158, 267.25) to (159.66, 269.5). Piece 5: C142.1 and IC2.J8, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (163.16, 275) to (165.18, 276.02). Piece 6: IC2.R14, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (156.65, 268.55) to (157.66, 269.5). Only IC2 has pins in more than one piece; if those pins are bonded inside the package the net is whole, and if not, the copper leaves it open. A track or a via of the net joining the pieces closes it.

    • split:P2V5P2V5's copper is in 3 pieces joined only through IC2: C232.2, IC2.R10 and IC2.T9 and 1 other piece(s) are connected only if the part bonds its pins inside

      P2V5's copper is in 3 pieces joined only through IC2: C232.2, IC2.R10 and IC2.T9 and 1 other piece(s) are connected only if the part bonds its pins inside. Piece 1: C121.2, C141.2, C143.2, C144.2, C145.2, C146.2, C147.2, C149.2 and 57 more pin(s), on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 30 drill(s), 310.85 mm2 of pour, over (143.4, 245.64) to (222.03, 284.03). Piece 2: C232.2, IC2.R10 and IC2.T9, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (155.68, 273) to (157.66, 275.05). Piece 3: C160.2 and IC2.T13, on TOP_LAYER, LAYER2, L3, L4, LAYER5 and BOTTOM_LAYER, 1 drill(s), over (154.93, 268.8) to (156.66, 270.5). Only IC2 has pins in more than one piece; if those pins are bonded inside the package the net is whole, and if not, the copper leaves it open. A track or a via of the net joining the pieces closes it.

  12. PartLifecyclemajorOpen

    PartLifecycle: 2 part numbers×2

    1 Not For New Designs, 1 Obsolete · on 2 placements

    At IC21, IC8

    Each finding, with its own headline
    • IC21CP2102-GM on IC21: the distributor catalogue reports "Not For New Designs" for Silicon Labs's CP2102-GM

      CP2102-GM on IC21: the distributor catalogue reports "Not For New Designs" for Silicon Labs's CP2102-GM — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/CP2102-GM/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • IC8M25P32-VMF6P on IC8: the distributor catalogue reports "Obsolete" for Micron Technology Inc.'s M25P32-VMF6P

      M25P32-VMF6P on IC8: the distributor catalogue reports "Obsolete" for Micron Technology Inc.'s M25P32-VMF6P — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/M25P32-VMF6P/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

  13. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 19 boards×19

    e.g. “'NetC165_2' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.13 mm (fastest: NetC165_2 at 100 ps 10-90 %, ASSUMED)” · 18 different statements

    At along@LAYER5:P2V5|P3V3, refchange:GND|P2V5, refchange:GND|P3V3, refchange:GND|VREF_A_M2C, split@LAYER5:P2V5|P3V3, void:GND@LAYER2:hole 150.58,277.35|150.97,277.73 and 13 more

    Each finding, with its own headline
    • along@LAYER5:P2V5|P3V34 nets run ALONG the split between the P2V5 and P3V3 planes on LAYER5 at 4 places, the longest 0.66 mm; the impedance rises from 51 ohm to 55 ohm there at worst, 3.6 % of each edge reflected (fastest: LA16_N at 100 ps 10-90 %, ASSUMED)

      On LAYER5 the P2V5 and P3V3 planes part, and 4 nets run down the slot between them at 4 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 51 ohm to 77 ohm; along the slot 55 ohm to 78 ohm, reflecting up to 3.6 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 90 ohm). At 1 place(s) the impedance cannot be said: the slot's two edges were not both read beside the track. At 3 of the 4 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.

      • 'SI57X_OE' on L4 at (168.9, 271.83), 0.46 mm, running ALONG the split for 0.23 mm, not across it, impedance not said: the slot's two edges were not both read beside the track; other side: no plane on L3
      • 'CLK0_M2C_N' on L4 at (168.49, 267.2), 0.6 mm, running ALONG the split for 0.41 mm, not across it, 51 ohm over solid plane, 55 ohm along it: 3.6 % of each edge reflected; other side: no plane on L3
      • 'LA16_N' on L4 at (150.9, 271.25), 0.61 mm, running ALONG the split for 0.42 mm, not across it, 51 ohm over solid plane, 55 ohm along it: 3.5 % of each edge reflected; other side: no plane on L3
      • 'NetIC2_D4' on BOTTOM_LAYER at (170.99, 281.49), 0.97 mm, running ALONG the split for 0.66 mm, not across it, 77 ohm over solid plane, 78 ohm along it: 0.2 % of each edge reflected; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=along%40LAYER5%3AP2V5%7CP3V3 serves each with its own layer_image region; all of them lie in x 149.68..172.39, y 266.06..282.49 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:GND|P2V534 nets change reference between GND and P2V5 at 36 vias, none with a reference that continues across (fastest: LA02_N at 100 ps 10-90 %, ASSUMED)

      At 36 via(s), on 34 net(s), the signal leaves a layer referenced by one of GND and P2V5 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 36 with none. 36 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P2V5 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'NetIC2_D4' at (168.91, 279.81), TOP_LAYER -> BOTTOM_LAYER: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 44.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C152 (100 nF 0402) 2.2 mm away: 1.61 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 94.9 ohm at the knee, 190 % of 50 ohm (assumed track impedance). None.
      • 'NetIC2_D18' at (168.85, 264.78), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 33.6 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C141 (1 uF 0603) 2.2 mm away: 1.63 nH in the 1.420 mm cavity + 0.51 nH ESL + 1.14 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 103.1 ohm at the knee, 206 % of 50 ohm (assumed track impedance). None.
      • 'LA07_P' at (154.96, 274.74), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 31.7 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C155 (100 nF 0402) 2.2 mm away: 1.61 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 95.0 ohm at the knee, 190 % of 50 ohm (assumed track impedance). None.
      • 'LA30_P' at (153.92, 265.72), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 31.6 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C231 (100 nF 0402) 2.6 mm away: 1.71 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 98.1 ohm at the knee, 196 % of 50 ohm (assumed track impedance). None.
      • 'LA02_P' at (152.97, 277.69), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 31.6 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C169 (10 nF 0603) 2.2 mm away: 1.62 nH in the 1.420 mm cavity + 0.51 nH ESL + 1.14 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 102.9 ohm at the knee, 206 % of 50 ohm (assumed track impedance). None.
      • 'LA02_N' at (151.95, 277.75), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 31.4 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C169 (10 nF 0603) 1.8 mm away: 1.51 nH in the 1.420 mm cavity + 0.51 nH ESL + 1.14 nH mounting (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 99.4 ohm at the knee, 199 % of 50 ohm (assumed track impedance). None.
      • 'LA03_N' at (152.92, 275.8), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 30.4 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C155 (100 nF 0402) 0.9 mm away: 1.10 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 79.0 ohm at the knee, 158 % of 50 ohm (assumed track impedance). None.
      • 'LA07_N' at (154, 274.65), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 30.2 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C155 (100 nF 0402) 1.2 mm away: 1.29 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 85.0 ohm at the knee, 170 % of 50 ohm (assumed track impedance). None.
      • 'LA30_N' at (152.91, 264.75), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 30.0 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C231 (100 nF 0402) 2.5 mm away: 1.70 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the second net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 97.9 ohm at the knee, 196 % of 50 ohm (assumed track impedance). None.
      • 'LA21_P' at (154, 269.88), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 29.8 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C160 (100 nF 0402) 1.4 mm away: 1.37 nH in the 1.420 mm cavity + 0.30 nH ESL + 2.20 nH mounting (pad 0.07 nH (vias beside the pads) + 1 via pair(s) at 2.14 mm pitch, 0.20 mm drill, 1.74 mm to the farther plane): 121.7 ohm at the knee, 243 % of 50 ohm (assumed track impedance). None.
      • 'LA16_P' at (152.98, 270.82), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 29.2 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA11_P' at (152.94, 273.77), TOP_LAYER -> L4: GND on LAYER2 to P2V5 on LAYER5; pure, no reference continues across; stitching none, 28.7 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P2V5 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. Measured for reference: C155 (100 nF 0402) 1.2 mm away: 1.26 nH in the 1.420 mm cavity + 0.30 nH ESL + 1.11 nH mounting (pad 0.07 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 1.74 mm depth, ASSUMED): 84.0 ohm at the knee, 168 % of 50 ohm (assumed track impedance). None.
      • and 24 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=refchange%3AGND%7CP2V5 serves each with its own layer_image region; all of them lie in x 149.9..173.84, y 258.63..282.66 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:GND|P3V369 nets change reference between GND and P3V3 at 97 vias, none with a reference that continues across (fastest: LA00_N at 100 ps 10-90 %, ASSUMED)

      At 97 via(s), on 69 net(s), the signal leaves a layer referenced by one of GND and P3V3 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 97 with none. 97 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and P3V3 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • 'LED_TOP' at (195.35, 268.35), L3 -> BOTTOM_LAYER: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 63.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LED_BOT' at (195.4, 267.6), L3 -> BOTTOM_LAYER: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 55.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC2_B18' at (184.12, 263.08), TOP_LAYER -> BOTTOM_LAYER: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 49.8 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'UART_RXD' at (171.9, 283.82), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 36.7 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (3 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'UART_RXD' at (179.41, 259.06), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 36.7 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (3 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC2_A2' at (171.9, 284.58), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 36.5 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'NetIC2_A2' at (179.95, 258.5), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 36.5 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA03_P' at (126.57, 287.33), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 32.4 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA07_P' at (126.6, 282.33), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 31.7 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA30_P' at (127.18, 255.96), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 31.6 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA02_P' at (127.3, 289.8), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 31.6 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'LA02_N' at (127.15, 288.88), TOP_LAYER -> L4: GND on LAYER2 to P3V3 on LAYER5; pure, no reference continues across; stitching none, 31.4 mm of track past the via on L4: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and P3V3 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 85 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=refchange%3AGND%7CP3V3 serves each with its own layer_image region; all of them lie in x 124.47..250.95, y 244.57..302.3 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:GND|VREF_A_M2C'2V5_CSO_B' changes reference between GND and VREF_A_M2C at 2 vias, none with a reference that continues across (fastest: 2V5_CSO_B at 20 ns 10-90 %, suggested by its name)

      At 2 via(s), on 1 net(s), the signal leaves a layer referenced by one of GND and VREF_A_M2C for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 2 with none. 2 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether GND and VREF_A_M2C are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.

      • '2V5_CSO_B' at (141.06, 252.55), TOP_LAYER -> LAYER5: GND on LAYER2 to VREF_A_M2C on BOTTOM_LAYER; pure, no reference continues across; stitching none, 30.0 mm of track past the via on LAYER5: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VREF_A_M2C are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '2V5_CSO_B' at (145.44, 280.07), TOP_LAYER -> LAYER5: GND on LAYER2 to VREF_A_M2C on BOTTOM_LAYER; pure, no reference continues across; stitching none, 30.0 mm of track past the via on LAYER5: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. GND and VREF_A_M2C are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=refchange%3AGND%7CVREF_A_M2C serves each with its own layer_image region; all of them lie in x 139.06..147.44, y 250.55..282.07 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • split@LAYER5:P2V5|P3V330 nets cross the split between the P2V5 and P3V3 planes on LAYER5 at 34 places, with no plane on the track's other side (fastest: LA02_N at 100 ps 10-90 %, ASSUMED)

      On LAYER5 the P2V5 and P3V3 planes part, and 30 nets cross from one to the other at 34 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 34 crossing(s) the track's other neighbour carries a plane, which the return can use there; 2 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '2V5_M1' on L4 at (149.76, 262.32), 0.19 mm; other side: no plane on L3
      • 'CLK0_M2C_P' on L4 at (168.88, 266.8), 0.19 mm; other side: no plane on L3
      • 'CLK20_VCXO' on L4 at (167.32, 273.18), 0.19 mm; other side: no plane on L3
      • 'CLK20_VCXO' on L4 at (167.32, 274.79), 0.13 mm; other side: no plane on L3
      • 'CLK20_VCXO' on L4 at (168.75, 275.15), 0.17 mm; other side: no plane on L3
      • 'FPGA_TMS' on BOTTOM_LAYER at (168.41, 262.53), 0.19 mm; other side: none: the signal layer is outermost
      • 'LA02_N' on L4 at (148.1, 278.6), 0.13 mm; other side: no plane on L3
      • 'LA02_P' on L4 at (148.1, 278.86), 0.13 mm; other side: no plane on L3
      • 'LA03_N' on L4 at (148.1, 276.43), 0.13 mm; other side: no plane on L3
      • 'LA03_P' on L4 at (148.1, 276.74), 0.13 mm; other side: no plane on L3
      • 'LA07_N' on L4 at (148.1, 274.85), 0.13 mm; other side: no plane on L3
      • 'LA07_P' on L4 at (148.1, 275.11), 0.13 mm; other side: no plane on L3
      • and 22 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=split%40LAYER5%3AP2V5%7CP3V3 serves each with its own layer_image region; all of them lie in x 144.67..171.99, y 258.43..282.51 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 150.58,277.35|150.97,277.73'LA05_P' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.51 mm (fastest: LA05_P at 100 ps 10-90 %, ASSUMED)

      Along 'LA05_P' on TOP_LAYER, the GND plane on LAYER2 has 0.51 mm under the track with no copper, at (150.75, 277.53), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 150.58..150.97, y 277.35..277.73. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LA05_P' on TOP_LAYER at (150.75, 277.53), 0.51 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20150.58%2C277.35%7C150.97%2C277.73 serves each with its own layer_image region; all of them lie in x 149.59..151.97, y 276.38..278.69 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 152.6,276.76|152.99,277.15'LA04_N' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.31 mm (fastest: LA04_N at 100 ps 10-90 %, ASSUMED)

      Along 'LA04_N' on L3, the GND plane on LAYER2 has 0.31 mm under the track with no copper, at (152.75, 276.99), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 152.6..152.99, y 276.76..277.15. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LA04_N' on L3 at (152.75, 276.99), 0.31 mm over no copper; other side: no plane on L4

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20152.6%2C276.76%7C152.99%2C277.15 serves each with its own layer_image region; all of them lie in x 151.65..153.86, y 275.88..278.1 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 154.1,268.31|154.49,268.7'LA22_N' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.25 mm (fastest: LA22_N at 100 ps 10-90 %, ASSUMED)

      Along 'LA22_N' on L3, the GND plane on LAYER2 has 0.25 mm under the track with no copper, at (154.34, 268.46), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 154.1..154.49, y 268.31..268.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 0 of the 1 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • 'LA22_N' on L3 at (154.34, 268.46), 0.25 mm over no copper; other side: VREF_A_M2C on L4, 1 mm from the track against 0.32 mm to LAYER2: 76% of the return on LAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20154.1%2C268.31%7C154.49%2C268.7 serves each with its own layer_image region; all of them lie in x 153.25..155.43, y 267.37..269.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 167.97,277.16|168.36,277.55'LED_BOT' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.24 mm (fastest: LED_BOT at 100 ps 10-90 %, ASSUMED)

      Along 'LED_BOT' on L3, the GND plane on LAYER2 has 0.24 mm under the track with no copper, at (168.2, 277.31), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 167.97..168.36, y 277.16..277.55. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 0 of the 1 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • 'LED_BOT' on L3 at (168.2, 277.31), 0.24 mm over no copper; other side: VREF_A_M2C on L4, 1 mm from the track against 0.32 mm to LAYER2: 76% of the return on LAYER2

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20167.97%2C277.16%7C168.36%2C277.55 serves each with its own layer_image region; all of them lie in x 167.12..169.29, y 276.23..278.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 170.39,271.73|170.78,272.12'NetC165_2' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.13 mm (fastest: NetC165_2 at 100 ps 10-90 %, ASSUMED)

      Along 'NetC165_2' on TOP_LAYER, the GND plane on LAYER2 has 0.13 mm under the track with no copper, at (170.71, 271.78), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 170.39..170.78, y 271.73..272.12. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetC165_2' on TOP_LAYER at (170.71, 271.78), 0.13 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20170.39%2C271.73%7C170.78%2C272.12 serves each with its own layer_image region; all of them lie in x 169.65..171.78, y 270.78..272.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 171.03,271.73|171.42,272.12'NetC165_2' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.13 mm (fastest: NetC165_2 at 100 ps 10-90 %, ASSUMED)

      Along 'NetC165_2' on TOP_LAYER, the GND plane on LAYER2 has 0.13 mm under the track with no copper, at (171.1, 271.78), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. What cleared it: the hole at x 171.03..171.42, y 271.73..272.12. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetC165_2' on TOP_LAYER at (171.1, 271.78), 0.13 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20171.03%2C271.73%7C171.42%2C272.12 serves each with its own layer_image region; all of them lie in x 170.03..172.16, y 270.78..272.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@LAYER2:hole 231.96,291.12|232.37,291.53'NetJ7_2' crosses one void in the GND plane on LAYER2 at 1 place, the longest 0.51 mm (fastest: NetJ7_2 at 100 ps 10-90 %, ASSUMED)

      Along 'NetJ7_2' on TOP_LAYER, the GND plane on LAYER2 has 0.51 mm under the track with no copper, at (232.14, 291.34), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.25 mm). What cleared it: the hole at x 231.96..232.37, y 291.12..291.53. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'NetJ7_2' on TOP_LAYER at (232.14, 291.34), 0.51 mm, running ALONG the bare copper for 0.25 mm, not across it over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AGND%40LAYER2%3Ahole%20231.96%2C291.12%7C232.37%2C291.53 serves each with its own layer_image region; all of them lie in x 230.96..233.33, y 290.16..292.52 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P2V5@LAYER5:hole 140.58,245.51|215.19,282.05'CLK20_VCXO' crosses one void in the P2V5 plane on LAYER5 at 1 place, the longest 0.59 mm; 1 over tracks of other nets routed inside it (fastest: CLK20_VCXO at 1 ns 10-90 %, suggested by its name)

      Along 'CLK20_VCXO' on L4, the P2V5 plane on LAYER5 has 0.59 mm under the track with copper of P1V2, not a plane, at (167.32, 272.02), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. What cleared it: the hole at x 140.58..215.19, y 245.51..282.05. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'CLK20_VCXO' on L4 at (167.32, 272.02), 0.59 mm over copper of P1V2, not a plane; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP2V5%40LAYER5%3Ahole%20140.58%2C245.51%7C215.19%2C282.05 serves each with its own layer_image region; all of them lie in x 166.21..168.32, y 270.77..273.31 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P3V3@LAYER5:132.6,282.71'LA04_N' crosses where the outline of the P3V3 plane on LAYER5 is drawn back, at 1 place, the longest 5.95 mm (fastest: LA04_N at 100 ps 10-90 %, ASSUMED)

      Along 'LA04_N' on L4, the P3V3 plane on LAYER5 has 5.95 mm under the track with no copper, at (132.6, 282.71), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 132.95..265.49, y 243.48..301.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LA04_N' on L4 at (132.6, 282.71), 5.95 mm over no copper, to the end of the track; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP3V3%40LAYER5%3A132.6%2C282.71 serves each with its own layer_image region; all of them lie in x 130.04..136.98, y 279.76..283.71 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P3V3@LAYER5:133.18,284.38'LA03_N' crosses where the outline of the P3V3 plane on LAYER5 is drawn back, at 1 place, the longest 5.71 mm (fastest: LA03_N at 100 ps 10-90 %, ASSUMED)

      Along 'LA03_N' on L4, the P3V3 plane on LAYER5 has 5.71 mm under the track with no copper, at (133.18, 284.38), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 132.95..265.49, y 243.48..301.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LA03_N' on L4 at (133.18, 284.38), 5.71 mm over no copper, to the end of the track; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP3V3%40LAYER5%3A133.18%2C284.38 serves each with its own layer_image region; all of them lie in x 129.59..136.98, y 282.87..285.67 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P3V3@LAYER5:135.42,281.68'LA04_P' crosses where the outline of the P3V3 plane on LAYER5 is drawn back, at 1 place, the longest 1.58 mm (fastest: LA04_P at 100 ps 10-90 %, ASSUMED)

      Along 'LA04_P' on L4, the P3V3 plane on LAYER5 has 1.58 mm under the track with no copper, at (135.42, 281.68), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 132.95..265.49, y 243.48..301.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LA04_P' on L4 at (135.42, 281.68), 1.58 mm over no copper, to the end of the track; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP3V3%40LAYER5%3A135.42%2C281.68 serves each with its own layer_image region; all of them lie in x 133.86..136.98, y 280.12..283.23 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P3V3@LAYER5:hole 140.58,245.51|215.19,282.0530 nets cross one void in the P3V3 plane on LAYER5 at 32 places, the longest 3.22 mm; 32 over tracks of other nets routed inside it (fastest: LA02_N at 100 ps 10-90 %, ASSUMED)

      Along 'LED_BOT' on L4, the P3V3 plane on LAYER5 has 3.22 mm under the track with copper of P1V2, not a plane, at (175.67, 273.08), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 32 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.72 mm). 32 places on 30 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 140.58..215.19, y 245.51..282.05. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'LED_BOT' on L4 at (175.67, 273.08), 3.22 mm, running ALONG the bare copper for 2.72 mm, not across it over copper of P1V2, not a plane; other side: no plane on L3
      • 'UART_RXD' on L4 at (181.85, 273.05), 1.06 mm, running ALONG the bare copper for 0.24 mm, not across it over copper of P1V2, not a plane; other side: no plane on L3
      • 'LED_BOT' on BOTTOM_LAYER at (211.38, 262.44), 0.73 mm over copper of P1V2, not a plane; other side: none: the signal layer is outermost
      • 'LED_TOP' on BOTTOM_LAYER at (211.38, 263.71), 0.73 mm over copper of P1V2, not a plane; other side: none: the signal layer is outermost
      • 'LED_TOP' on L4 at (177.35, 273.16), 0.73 mm over copper of P1V2, not a plane; other side: no plane on L3
      • 'NetIC2_B18' on BOTTOM_LAYER at (196.03, 272.98), 0.73 mm over copper of P1V2, not a plane; other side: none: the signal layer is outermost
      • 'FPGA_TMS' on BOTTOM_LAYER at (167.53, 261.92), 0.62 mm over copper of P1V8, not a plane; other side: none: the signal layer is outermost
      • '2V5_M1' on L4 at (143.3, 257.39), 0.54 mm over copper of 2V5_CSO_B, not a plane; other side: no plane on L3
      • 'LA16_N' on L4 at (145.76, 271.4), 0.54 mm over copper of 2V5_CSO_B, not a plane; other side: no plane on L3
      • 'LA21_P' on L4 at (145.09, 270.73), 0.54 mm over copper of 2V5_CSO_B, not a plane; other side: no plane on L3
      • 'SI57X_SDA' on BOTTOM_LAYER at (183.45, 272.79), 0.53 mm over copper of P1V2, not a plane; other side: none: the signal layer is outermost
      • 'LA07_N' on L4 at (145.7, 274.85), 0.53 mm over copper of 2V5_CSO_B, not a plane; other side: no plane on L3
      • and 20 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP3V3%40LAYER5%3Ahole%20140.58%2C245.51%7C215.19%2C282.05 serves each with its own layer_image region; all of them lie in x 142.21..212.64, y 256.39..279.86 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:P3V3@LAYER5:hole 170.47,267.39|172.38,270.212 nets cross one void in the P3V3 plane on LAYER5 at 2 places, the longest 0.65 mm; 2 over tracks of other nets routed inside it (fastest: NetIC2_G15 at 100 ps 10-90 %, ASSUMED)

      Along 'SI57X_CLK_N' on L4, the P3V3 plane on LAYER5 has 0.65 mm under the track with copper of MGT_AVC_A, not a plane, at (171.38, 268.39), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x 170.47..172.38, y 267.39..270.21. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'SI57X_CLK_N' on L4 at (171.38, 268.39), 0.65 mm over copper of MGT_AVC_A, not a plane; other side: no plane on L3
      • 'NetIC2_G15' on L4 at (170.88, 269.18), 0.46 mm over copper of MGT_AVC_A, not a plane; other side: no plane on L3

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3AP3V3%40LAYER5%3Ahole%20170.47%2C267.39%7C172.38%2C270.21 serves each with its own layer_image region; all of them lie in x 169.64..172.71, y 267.39..270.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@L3|L412 nets on L3 cross the tracks routed through the VREF_A_M2C pour on L4 at 17 places, the longest 86.92 mm; 15 run ALONG the cut round another net's track (fastest: LA22_N at 100 ps 10-90 %, ASSUMED)

      The VREF_A_M2C pour on L4 is cleared round tracks routed through it, and tracks on L3, which take that pour as their reference, cross them: for the width of each cut the return has no plane under it and detours round the cut. 17 place(s) on 12 net(s). 15 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 41.21 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 16 of the 17 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • 'NetIC2_H14' on L3 at (166.29, 268.69), 0.44 mm over copper of NetIC2_G15, not a plane, to the end of the track; other side: no plane on LAYER2
      • 'NetIC2_F17' on L3 at (223.4, 276.4), 86.92 mm, running ALONG the bare copper for 41.21 mm, not across it over copper of NetIC2_D18, UART_RXD, NetIC2_A2, P3V3, P1V8, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'NetIC2_G16' on L3 at (195.92, 262.18), 34.14 mm, running ALONG the bare copper for 19.3 mm, not across it over copper of NetIC2_D18, UART_RXD, NetIC2_A2, P3V3, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'LA22_N' on L3 at (131.37, 267.69), 27.74 mm, running ALONG the bare copper for 20.28 mm, not across it over copper of LA21_P, LA21_N, LA24_P, LA24_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'LA25_N' on L3 at (144.83, 267.01), 26.79 mm, running ALONG the bare copper for 18.33 mm, not across it over copper of LA21_N, LA21_P, LA24_P, LA24_N, LA28_P, LA28_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'LA22_P' on L3 at (144.24, 268.67), 18.01 mm, running ALONG the bare copper for 11.98 mm, not across it over copper of LA21_P, LA21_N, LA24_P, LA24_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'FPGA_CLK_N' on L3 at (167.34, 282.39), 11.28 mm, running ALONG the bare copper for 3.67 mm, not across it over copper of P1V5, PLL25DAC_DIN, PLL25DAC2_SYNC_N, PLL25DAC_SCLK, PLL25DAC1_SYNC_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'NetIC2_H14' on L3 at (170.49, 268.29), 10.61 mm, running ALONG the bare copper for 8.98 mm, not across it over copper of SI57X_CLK_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'FPGA_CLK_P' on L3 at (167.56, 282.17), 10.53 mm, running ALONG the bare copper for 3.08 mm, not across it over copper of P1V5, PLL25DAC_DIN, PLL25DAC2_SYNC_N, PLL25DAC_SCLK, PLL25DAC1_SYNC_N, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'LED_BOT' on L3 at (171.53, 271.71), 8.15 mm, running ALONG the bare copper for 4.66 mm, not across it over copper of CLK20_VCXO, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'LA29_P' on L3 at (148.52, 264.54), 5.77 mm, running ALONG the bare copper for 4.65 mm, not across it over copper of LA30_N, LA30_P, not a plane, to the end of the track; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • 'NetIC2_G16' on L3 at (167.48, 267.28), 2.81 mm, running ALONG the bare copper for 1.29 mm, not across it over copper of CLK0_M2C_N, CLK0_M2C_P, not a plane; other side: GND on LAYER2, 0.32 mm from the track against 1 mm to L4: 24% of the return on L4
      • and 5 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/46/reference-planes?group=void%3Arouted%40L3%7CL4 serves each with its own layer_image region; all of them lie in x 125.49..236.9, y 260.78..286.04 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  14. observationOBS-169minorOpen

    Board input pads are silk-labelled '12v' while the rail they feed is named P24V

    The power input pads are silk-labelled 12v, but the rail they feed is named P24V.

    The input is a pair of bottom-side wire pads labelled 12v and gnd. A wide trace runs from the 12v pad to D2 (SS34) pad 2 (NetD2_2); D2 pad 1, D1 pad 1 and fuse F2 pad 1 share NetD1_1; F2 pad 2 is P24V, which feeds the JTF1224S3V3 module (9-36 VDC input).

    Both voltages are inside the module's 9-36 V range, so nothing is damaged either way, but the operator label and the design name disagree. Pick one and make the silk and net agree.

    The input sheet with D1, D2, F2 and LD6 is not in the published schematic PDF (it holds 11 of 17 sheets).

  15. observationOBS-171minorOpen

    Configuration flash IC8 (M25P32 at 3.3 V) is driven from FPGA bank 2 at 2.5 V: guaranteed LVCMOS25 VOH (VCCO - 0.4 V) is below the flash VIH minimum (0.7 x VCC)

    IC2 bank 2 (VCCO 2.5 V) drives CCLK, MOSI and CSO_B of the 3.3 V configuration flash IC8 (M25P32); the FPGA's guaranteed high of 2.1 V is below the flash's guaranteed VIH of 2.31 V.

    Where it is

    IC2 bank 2 VCCO is P2V5. IC8 (M25P32-VMF6P) is supplied from P3V3 (pins 2, 1 HOLD# and 9 W#); pin 10 is GND.

    SignalIC2 ballNetIC8 pin
    CCLKY20 (IO_L1P_CCLK_2)2V5_CCLK16
    MOSIAB20 (IO_L3N_MOSI_CSI_B_MISO0_2)2V5_MOSI15
    CSO_BAA3 (IO_L65N_CSO_B_2)2V5_CSO_B, pulled up to P3V3 by R1037

    The numbers

    QuantityValueSource
    LVCMOS25 VOH minVCCO - 0.4 V = 2.1 V at 2.5 VDS162 Table 9 (XC6SLX45T datasheet, p.10)
    M25P32 VIH min0.7 x VCC = 2.31 V at 3.3 VM25P32 datasheet, p.37
    LVCMOS25 VIH max4.1 VDS162 Table 9

    The FPGA's guaranteed high level therefore does not meet the flash's guaranteed input-high threshold on CCLK, MOSI and CSO_B during configuration. With a single CMOS load the real high level is close to 2.5 V, so it may work on the bench, but the margin is not guaranteed by either datasheet. The reverse direction (flash DQ1 at 3.3 V into MISO) is within the LVCMOS25 VIH max of 4.1 V.

    Fix

    Supplying the flash from 2.5 V is not an option (M25P32 needs 2.7 V to 3.6 V), so the usual fixes are VCCO_2 = 3.3 V or a 1.8/2.5 V-capable flash.

  16. observationOBS-172minorOpen

    USB ESD protector IC22 sits about 5 mm from J8 while the CP2102 IC21 D+/D- pins are directly behind the J8 contacts, so a discharge reaches the bridge before the protector

    The USB ESD array IC22 is about 5.4 mm from connector J8, while the CP2102 (IC21) D+/D- pins sit about 0.3-0.6 mm behind the J8 contacts, so a discharge reaches the bridge before the clamp.

    Where it is

    PartPinNetPosition (mm)Side
    J8 mini-USBpad 2 (D-)NetIC21_5183.90, 252.92bottom
    J8 mini-USBpad 3 (D+)NetIC21_4183.10, 252.92bottom
    IC21 CP2102pin 5NetIC21_5183.89, 253.47top
    IC21 CP2102pin 4NetIC21_4183.39, 253.47top
    IC22 PRTR5V0U2Xpin 2NetIC21_5179.65, 247.53top
    IC22 PRTR5V0U2Xpin 3NetIC21_4181.95, 247.53top

    IC21's pins are about 0.3-0.6 mm from the J8 contacts in plan; IC22, the ESD diode array on the same nets, is about 5.4 mm away.

    ``mermaid flowchart LR J8["J8 D+ / D-"] -- "about 0.3-0.6 mm" --> IC21["IC21 CP2102"] J8 -- "about 5.4 mm, separate branch" --> IC22["IC22 PRTR5V0U2X<br/>ESD clamp"] ``

    Why it matters

    An ESD protector works best between the connector and the protected pin, so the discharge is clamped before it reaches the silicon. Here the CP2102 pins are closer to the connector than the clamp, and the clamp is reached through a separate branch of the same nets. The CP2102 has its own ESD structures, and this is a service USB port, so the practical risk is modest. Moving IC22 between J8 and IC21, or routing J8 -> IC22 -> IC21, would restore the intended order.

  17. observationOBS-173minorOpen

    Published schematic is incomplete: three sheets referenced by the Altium project are missing, so the FPGA configuration/JTAG circuit and the 1.5 V linear supply have no schematic

    Three sheets of the Altium project are not in the repository, so the FPGA configuration/JTAG circuit (IC8) and the 1.5 V linear supply (IC40) appear on no published schematic.

    What is missing

    ticks_fmc_HW/ticop.PrjPcb (commit 241c3998) lists 14 schematic documents. The repository holds only the 11 sheets under ticks_fmc_HW/schematics. Missing:

    • FMC_PCIe_Carrierop.SchDoc (the top sheet)
    • JTAG&CONFIGoh.SchDoc
    • power_supply_linearoh.SchDoc

    The title blocks number the sheets up to 17.

    Parts placed on the PCB but on no published sheet

    • IC8, M25P32 configuration flash (wired to IC2 bank 2 configuration pins)
    • IC40, TPS74401 1.5 V LDO, with its divider R30/R148/R163/R192 and PG pull-up R290
    • FPGA mode straps R35/R93
    • PROGRAM_B/DONE pull-ups r700/r701, TMS pull-up R236
    • R103, R142, LD1, LD6, R189 and 14 capacitors

    Why it matters

    A reader of the published design cannot see how the FPGA is configured, how its mode is strapped, or how P1V5 is made; the review of those circuits here had to rely on the PCB netlist alone. Adding the three missing .SchDoc files (or a PDF of the full 17-sheet set) to the repository would close this.

  18. observationOBS-174minorOpen

    u4 LM2832 catch diode D33 is a generic 'D Zener' with no part number, where the datasheet recommends a Schottky

    D33, the catch diode of the u4 LM2832 buck, is specified only as a generic D Zener with no part number, where the LM2832 datasheet recommends a Schottky.

    Where it is

    D33 pin 2 is on NetD33_2, the switch node (u4 pin 8 SW, inductor l12); pin 1 is on GND. Sheet 15/17 (Switching regulators) draws it with a zener symbol labelled D Zener.

    What the BOM says

    FieldValue
    DesignatorD33
    ValueD Zener
    DescriptionZener Diode
    Footprint3225[1210]
    LibRefD Zener
    Manufacturer / part numbernone

    Why it matters

    The LM2832 datasheet (p.12) says the catch diode conducts during the switch off-time and that a Schottky diode is recommended. A zener fitted here would conduct as an ordinary PN diode, with higher forward drop and reverse-recovery loss at the 0.55-3 MHz switching frequency. The BOM also gives an assembler nothing to buy. Naming a Schottky part (rated at least 2 A and above the 3.3 V input) would close it.

  19. observationOBS-175minorOpen

    SFP cage J7: LOS (pin 8) and TX_FAULT (pin 2) have no host pull-up and the gateware enables none, so both open-collector outputs float at the FPGA

    J7 TX_FAULT (pin 2) and LOS (pin 8) reach IC2 with no pull-up on the board and no PULLUP in the gateware, so both open-collector SFP status lines float when the module releases them.

    Where it is

    ``mermaid flowchart LR J2["J7 pin 2<br/>TX_FAULT"] -- "NetJ7_2" --> R104["R104 100R"] --> B18["IC2 B18<br/>LVCMOS25, no PULLUP"] J8["J7 pin 8<br/>LOS"] -- "NetJ7_8" --> R105["R105 100R"] --> D18["IC2 D18<br/>LVCMOS25, no PULLUP"] ``

    • No other part sits on either side of R104 or R105.
    • By contrast MOD_DEF0/1/2 do have pull-ups: R403/R402/R401 10k to P3V3.
    • The gateware constraints (HDL/top/ticks_fmc.ucf, commit 241c3998) set SFP_TX_FAULT_i (B18) and SFP_LOS_i (D18) to LVCMOS25 with no PULLUP attribute.

    Why it matters

    In the SFP MSA (INF-8074i) TX_FAULT and LOS are open-collector module outputs that the host must pull up (4.7-10 kOhm to host Vcc). Without it the FPGA inputs float when the module releases them, so loss-of-signal and transmitter-fault status are unreliable. The MSA is not on file on this server; the requirement is quoted from the published standard, not from a stored page.

    A 4.7-10k pull-up on each line, or a PULLUP constraint, would close it.

  20. observationOBS-176minorOpen

    Silkscreen designators superimposed: C255/C256 print as one string, R704 over C307, R703 over C308, R702 over l12

    Four pairs of designators on the top overlay are printed on top of each other, so those parts cannot be identified from the board.

    Where

    OverlapPositions (mm)Effect
    C255 / C256C255 (135.9, 246.1), C256 (137.4, 246.1), 1.5 mm apartdesignators read as one string, C2556
    R704 / C307R704 (233.7, 248.7), C307 (236.7, 249.0)designators overlap
    R703 / C308R703 overlaps the C308 designator and pads
    R702 / l12R702 overlaps the l12 designator

    Found on the Probe layer render of TOP_OVERLAY.

    Why it matters

    Superimposed designators cannot be read during assembly, inspection or rework. Moving the text apart in the PCB would close it.

  21. observationOBS-177minorOpen

    No polarity marks on the silkscreen for D1, D2 (SS34), D33 and LD6

    D1, D2 (SS34), D33 and LD6 have no polarity mark on the silkscreen, so nothing on the board shows which end is the cathode.

    What the silkscreen shows

    PartRoleSideOutline
    D1, D2SS34 Schottky, 12 V input path with F2bottomsymmetric brackets, no cathode mark
    D33LM2832 catch diode (pin 2 on u4 switch node NetD33_2, pin 1 on GND)topplain symmetric rectangle, no cathode bar
    LD60603 power LEDno outline or mark

    The ICs (IC19, IC22, IC21) do carry pin-1 marks.

    Why it matters

    • A reversed input diode blocks or shorts the supply through F2.
    • A reversed catch diode shorts the buck switch node.
    • A reversed LED stays dark.

    Without a cathode mark, assembly and inspection rely on the placement file alone.

  22. observationOBS-178minorOpen

    No global fiducials on the board; the only fiducial marks are the two local ones inside the IC2 BGA footprint

    No global fiducials anywhere on the board: the only fiducial marks are the two local pads FTG1/FTG2 inside the IC2 BGA footprint.

    What is there

    • The placement holds no fiducial components (251 parts: C, R, L, IC, J, U, D, OSC, LD, T, F and the SFP cage halves).
    • The top and bottom copper renders show no free fiducial pads.
    • IC2's footprint carries two local fiducial pads with no net:
    Padx (mm)y (mm)
    FTG1147.40285.25
    FTG2174.40258.25

    Why it matters

    Automated assembly aligns the board on at least two or three global fiducials; local fiducials at the BGA help only that part. The fine-pitch QFNs (IC6, IC21, IC40) and the FMC connector would be placed without a board reference, or the panel must carry the fiducials.

  23. observationOBS-179minorOpen

    Schematic title blocks carry no revision and a broken logo link on every sheet

    Every schematic title block has an empty Rev field and a broken logo link, so a printed sheet cannot be matched to a board revision.

    On every published sheet:

    • the Rev field reads -;
    • the logo box shows the text Cannot open file C:/Users/ronan/Downloads/apclogo... instead of the image.

    The blocks do carry the project (CTA TiCkS board), document title, designer, drawn/checked dates, file name and Sheet N of 17. Sheet 15 of 17 (Switching regulators, which shows u4) is one example; the other published sheets have the same title block.

Main parts

Part numberMakerDescriptionWhere
0154003.DRLittelfuse3 A 125 V fuse (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)F2
1367073-1TE Connectivity20-position SFP host connector (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)J7
1734035-1TE ConnectivityUSB mini-B receptacle, 5 pins + shield (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)J8
571-0112FDialightbi-colour LED, bottom green, top red (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)LD1
6367034-1TE ConnectivitySFP cage bottom (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)CageBot1
6367035-1TE ConnectivitySFP cage top (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)CageTop1
87833-1420MolexMilli-Grid 2 mm 14-way header (JTAG) (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)J3
ASP-134603-01SamtecVITA 57 FMC LPC connector, 160 contacts (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)J4
CDCM61004RHBTIC6
CP2102-GMIC21
DS18B20U+IC19
JTF1224S3V3XP PowerDC/DC converter module, value 'jtf1224.' (24 V in per the P24V rail, 3.3 V out to P3V3; output variant inferred from the rail) (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)u1
LFVCXO026156IQD20 MHz 3.3 V VCXO (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)OSC2
LM2832Texas Instruments2 A buck converter, value 'lm2832', 1.2 V output (P1V2) (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)u4
LM336M-2.5/NOPBIC10
LP5951MF-3.0/NOPBIC1
M25P32-VMF6PIC8
PRTR5V0U2XIC22
Si570BBC000121DGSilicon LabsI2C programmable XO 10-280 MHz (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)OSC4
SML-311UTT86KROHMred LED 0603 (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)LD6
SN65LVDS2DBVRIC20
TLV1117-18Texas InstrumentsLDO, value 'tlv11711v8' / symbol 'tlv117118' (TLV1117 1.8 V) (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)u2
TLV1117-25Texas InstrumentsLDO, value 'tlv11712V5' / symbol 'tlv117118' (TLV1117 2.5 V) (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)u3
TPS74401RGWTIC40
VM53S3-25.000-2.5/-30+75Mercury25 MHz VCXO, 2.5 V (MPN from the design BOM LibRef/footprint; Claude walker, Cern session)OSC5
XC6SLX45T-3FGG484CIC2
AD5662BRMZ-1IC3, IC7
BSH103T1, T2
SS34D1, D2
BLM21PG221SN1DMurataL1, L11, L2, L20, L21, L22 and 5 more

About this design

Design
SPEC TICKS — OHWR0045 R1
Designed in
Altium Designer
Board
6 copper layers, 164 × 60 mm, 251 components, 187 nets
Licence
CERN-OHL-1.1
Source
https://gitlab.com/ohwr/project/spec-ticks at commit 241c3998b195
Attribution
CERN Open Hardware Repository, project ohwr/project/spec-ticks (commit 241c3998b195e2a4e0b1a339796d8e50275e7e73, 2025-04-10). Licence: CERN-OHL-1.1 (stated on the schematic sheets). Source: https://gitlab.com/ohwr/project/spec-ticks. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)