Probe E# — E-Sharp AB
Probe is made by E# (E-Sharp AB) in Sweden. Want your own boards reviewed like this? Book a meeting

TIMIQ RF

OHWR0061 · revision R1

TIMIQ RF (OHWR0061 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in KiCad EDA: a 8-layer board of 150 × 160 mm with 464 components and 415 nets, published under CERN-OHL-1.2.

review 83% walked · 18 findings: 1 blocker · 10 major · 7 minor (148 items)

Open in the interactive viewerRead the full review

TIMIQ RF (OHWR0061 R1) circuit board, top view: copper, silkscreen and components
Top view, rendered by Probe from the design's own fabrication data.

Design review

Probe recorded 18 findings: 1 blocker · 10 major · 7 minor (148 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.

  1. observationOBS-525blockerOpen

    16 V aluminium electrolytics C144, C145, C156, C157 sit across the ±24 V inputs

    Four aluminium electrolytics rated 16 V (C144, C156 on +24 V; C145, C157 on -24 V) carry the full 24 V input, about 1.5x their rating, so they will vent or fail short at power-up.

    Where they are

    ``mermaid flowchart LR J6["J6 39-30-1061<br/>pin 3 / pin 5"] -- "+24 V" --> C144["C144 100uF 16V"] J6 -- "-24 V" --> C145["C145 100uF 16V"] C144 --> L13["L13 NFM41PC155"] --> R24["net 24V"] --> C156["C156 10uF 16V"] --> U43["U43 TPS7A4700 -> 15V"] C145 --> L14["L14 NFM41PC155"] --> R24N["net -24V"] --> C157["C157 10uF 16V"] --> U44["U44/U45 TPS7A3301 -> -5V/-15V"] ``

    The ratings against the rail

    PartValue / rating statedNet (other plate GND)Voltage acrossSource
    C144100 uF, 16 V (BOM 'EEEFC1A101P', '100uF-16V-20p-Al-TypeE')J6.3 side of L1324 Vschematic sheet 5 (PSU), netlist
    C15610 uF, 16 V (BOM 'EEEFC1C100R', '10uF-16V-20p-Al-TypeB')24V24 Vschematic sheet 5, netlist
    C145100 uF, 16 V (EEEFC1A101P)J6.5 side of L1424 V (on -24 V)schematic sheet 5, netlist
    C15710 uF, 16 V (EEEFC1C100R)-24V24 V (on -24 V)schematic sheet 5, netlist

    Why the rails really are ±24 V

    J6 brings in three supplies labelled 7V5, 24V and -24V on the PSU sheet. U43 (TPS7A4700) regulates the 24V net to 15V, and U44/U45 (TPS7A3301) regulate -24V to -5V and -15V, so the inputs must sit well above 15 V in magnitude.

    Why it matters

    A wet aluminium electrolytic's peak voltage must stay at or below its rated voltage (Nichicon CAT.8101H; Vishay 146 CTI), and above it the part vents. The orientation is correct on all four (C145/C157 have + on GND); only the rating is wrong.

    Note

    The Panasonic FC part number EEEFC1A101P carries voltage code '1A', which in Panasonic's numbering is 10 V, not the 16 V the schematic and BOM value state; either way it is below 24 V. Check which parts were ordered.

  2. observationOBS-162majorOpen

    U28 ordered as OPA209AIDGKR (single op-amp) but drawn and wired as the dual OPA2209: V+ lands on the single's NC pin 8 and channel B does not exist

    U28 is drawn and wired as the dual OPA2209 but the BOM orders the single OPA209AIDGKR: built to the MPN, V+ lands on the single's NC pin 8 and channel B does not exist.

    The part fields

    On sheet ADC, U28 has value 'OPA2209AIDGKR' and is placed as two op-amp units driving the ADS8694 inputs AIN_0P (U29 pin 16) and AIN_1P (U29 pin 18). Its 'Manufacturer ref' field, the MPN in the BOM, is 'OPA209AIDGKR' (Digi-Key 296-39109-1-ND), the single-channel part in the same VSSOP-8.

    Pin by pin

    PinBoard net (dual pinout)OPA209 single (SBOS426D, p.3)
    1OUT A: Net-(C110-Pad1), to U29.16 and R123NC
    2Net-(R119-Pad1)
    3Net-(C112-Pad1)
    4-5V
    5Net-(C113-Pad1)NC
    6Net-(R120-Pad1)OUT
    7OUT B: Net-(C111-Pad1), to U29.18 and R124V+
    85V_2NC

    Built to the BOM MPN

    • The op-amp's V+ (pin 7) sits on the OUT B net with no supply.
    • The 5V_2 rail goes to an NC pin.
    • Pin 6 (OUT) drives R120/R124 into the B feedback node.
    • Pins 1 and 5 are dead.
  3. CapVoltageDeratingmajorOpen

    CapVoltageDerating: 12 components×12

    12 checked by the review by Claude walker W2 (Cern session) — 12 different reasons

    At C145, C150, C157, C164, C168, C169 and 6 more

    Each finding, with its own headline
    • C145C145 sits on a 24 V rail and its voltage rating is not in the BOM

      C145: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source. 'Net-(C145-Pad2)' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C150C150 sits on a 24 V rail and its voltage rating is not in the BOM

      C150: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0805F104K5RACTU is on file; the rated voltage can be read there. 'Net-(C145-Pad2)' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C157C157 sits on a 24 V rail and its voltage rating is not in the BOM

      C157: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source. '-24V' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C164C164 sits on a 24 V rail and its voltage rating is not in the BOM

      C164: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0805F104K5RACTU is on file; the rated voltage can be read there. '-24V' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C168C168 sits on a 24 V rail and its voltage rating is not in the BOM

      C168: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C1210C106K3RACTU is on file; the rated voltage can be read there. '-24V' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C169C169 sits on a 24 V rail and its voltage rating is not in the BOM

      C169: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C1210C106K3RACTU is on file; the rated voltage can be read there. '-24V' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

    • C179C179 sits on a 15.05 V rail and its voltage rating is not in the BOM

      C179: on a 15.05 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0603C103J3GACTU is on file; the rated voltage can be read there. '-15V' sits at -15.05 V; a voltage rating is a magnitude, so it is judged at 15.05 V.

    • C31C31 sits on a 15.05 V rail and its voltage rating is not in the BOM

      C31: on a 15.05 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0603C103J3GACTU is on file; the rated voltage can be read there. '-15V' sits at -15.05 V; a voltage rating is a magnitude, so it is judged at 15.05 V.

    • C32C32 sits on a 15.05 V rail and its voltage rating is not in the BOM

      C32: on a 15.05 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0603C103J3GACTU is on file; the rated voltage can be read there. '-15V' sits at -15.05 V; a voltage rating is a magnitude, so it is judged at 15.05 V.

    • C49C49 sits on a 15.05 V rail and its voltage rating is not in the BOM

      C49: on a 15.05 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0603C103J3GACTU is on file; the rated voltage can be read there. '-15V' sits at -15.05 V; a voltage rating is a magnitude, so it is judged at 15.05 V.

    • C50C50 sits on a 15.05 V rail and its voltage rating is not in the BOM

      C50: on a 15.05 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. A datasheet for C0603C103J3GACTU is on file; the rated voltage can be read there. '-15V' sits at -15.05 V; a voltage rating is a magnitude, so it is judged at 15.05 V.

    • L14L14 sits on a 24 V rail and its voltage rating is not in the BOM

      L14: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source. '-24V' sits at -24 V; a voltage rating is a magnitude, so it is judged at 24 V.

  4. CapVoltageDeratingmajorOpen

    CapVoltageDerating: 3 components×3

    3 checked by the review by Claude walker W1 (Cern session) — 3 different reasons

    At C144, C156, L13

    Each finding, with its own headline
    • C144C144 sits on a 24 V rail and its voltage rating is not in the BOM

      C144: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source.

    • C156C156 sits on a 24 V rail and its voltage rating is not in the BOM

      C156: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source.

    • L13L13 sits on a 24 V rail and its voltage rating is not in the BOM

      L13: on a 24 V rail but its voltage rating is not stated in the BOM — add it so the rating can be compared to the rail at all. No datasheet is on file for this part; the BOM short-spec is the source.

  5. DecapViaFanoutmajorOpen

    DecapViaFanout: 9 components×9

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: 29 fan-out lengths read from the copper stand; the 0.5 nH limit is Probe's starting value, not a TPS7A or RF-part requirement, and no PDN target is stated. Left for the owner.

    At C143, C165, C166, C71, C75, C77 and 3 more

    Each finding, with its own headline
    • C143C143 on 'Net-(C143-Pad1)': its ground pad over 3.05 mm, adding about 1.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C143 on 'Net-(C143-Pad1)': its ground pad over 3.05 mm, adding about 1.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C143.1 (rail) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure; C143.2 (ground) runs 3.05 mm along its copper to its nearest via, 2.05 mm past the 1 mm beside the pad: 1.69 nH. Each run past the pad as one conductor of a pair 7.80 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.69 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.28 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.13 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C165C165 on '7V5': its rail pad reaches its via over 2.21 mm of track, adding about 0.77 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C165 on '7V5': its rail pad reaches its via over 2.21 mm of track, adding about 0.77 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C165.1 (rail) runs 2.21 mm along its copper to its nearest via, 1.21 mm past the 1 mm beside the pad: 0.77 nH; C165.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 3.00 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.77 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.65 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C166C166 on '7V5': its ground pad over 2.47 mm, adding about 0.93 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C166 on '7V5': its ground pad over 2.47 mm, adding about 0.93 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C166.1 (rail) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure; C166.2 (ground) runs 2.47 mm along its copper to its nearest via, 1.47 mm past the 1 mm beside the pad: 0.93 nH. Each run past the pad as one conductor of a pair 3.00 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.93 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.23 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.39 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C71C71 on '5V_2': its rail pad reaches its via over 3.86 mm of track, adding about 1.44 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C71 on '5V_2': its rail pad reaches its via over 3.86 mm of track, adding about 1.44 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C71.1 (rail) runs 3.86 mm along its copper to its nearest via, 2.86 mm past the 1 mm beside the pad: 1.44 nH; C71.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.58 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.44 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.00 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.65 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C75C75 on '5V_1': its rail pad reaches its via over 4.95 mm of track, adding about 1.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C75 on '5V_1': its rail pad reaches its via over 4.95 mm of track, adding about 1.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C75.1 (rail) runs 4.95 mm along its copper to its nearest via, 3.95 mm past the 1 mm beside the pad: 1.99 nH; C75.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.58 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.99 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.77 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C77C77 on '5V_1': its rail pad reaches its via over 3.82 mm of track, adding about 1.42 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C77 on '5V_1': its rail pad reaches its via over 3.82 mm of track, adding about 1.42 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C77.1 (rail) runs 3.82 mm along its copper to its nearest via, 2.82 mm past the 1 mm beside the pad: 1.42 nH; C77.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.58 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.42 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.77 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C79C79 on '5V_1': its rail pad reaches its via over 2.96 mm of track, adding about 0.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C79 on '5V_1': its rail pad reaches its via over 2.96 mm of track, adding about 0.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C79.1 (rail) runs 2.96 mm along its copper to its nearest via, 1.96 mm past the 1 mm beside the pad: 0.99 nH; C79.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.59 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.99 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.77 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C86C86 on '5V_1': its rail pad reaches its via over 4.19 mm of track, adding about 1.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C86 on '5V_1': its rail pad reaches its via over 4.19 mm of track, adding about 1.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C86.1 (rail) runs 4.19 mm along its copper to its nearest via, 3.19 mm past the 1 mm beside the pad: 1.61 nH; C86.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.59 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.61 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.08 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C91C91 on '5V_1': its rail pad reaches its via over 3.58 mm of track, adding about 1.30 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads

      C91 on '5V_1': its rail pad reaches its via over 3.58 mm of track, adding about 1.30 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads. C91.1 (rail) runs 3.58 mm along its copper to its nearest via, 2.58 mm past the 1 mm beside the pad: 1.30 nH; C91.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.59 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.30 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.77 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  6. FiducialMissingmajorOpen

    FiducialMissing: 2 boards×2

    Checked by the review, stands · Claude walker (cern session) — Stands: none of the 464 placed components is a fiducial (no FID footprint or refdes) on either side. Left for the owner.

    At bottom, top

    Each finding, with its own headline
    • bottomThe bottom side carries 31 SMT component(s) and no fiducial was found on it

      The bottom side carries 31 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='bottom', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

    • topThe top side carries 61 SMT component(s) and no fiducial was found on it

      The top side carries 61 SMT component(s) but no fiducial was found on it — a placement machine has no optical reference to align to. Probe found no pad labelled .pad_usage=g_fiducial/l_fiducial (basis pad_usage); no single-pad, netless, undrilled component whose 0.5-3 mm round pad has a concentric solder-mask opening at least 1.5x its diameter with no other copper inside it (basis geometry); and no component whose refdes starts FID or whose part or package name contains FIDUCIAL (basis footprint-name). If your library names fiducials something Probe does not recognise, mark this benign — disposition_finding(rule='FiducialMissing', entity='top', status='benign', reason=…) — the name match only ever silences this check, it never asserts anything. If the side really has no fiducial, say so with status='confirmed': that answers the finding and keeps it gating release.

  7. FloatingInputmajorOpen

    FloatingInput: 2 nets×2

    2 checked by the review by Claude walker (cern session) — 2 different reasons

    At Net-(U29-Pad10), Net-(U29-Pad11)

    Each finding, with its own headline
    • Net-(U29-Pad10)U29.10 on 'Net-(U29-Pad10)' has no driver and no pull

      Net 'Net-(U29-Pad10)': input(s) U29.10 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor.

    • Net-(U29-Pad11)U29.11 on 'Net-(U29-Pad11)' has no driver and no pull

      Net 'Net-(U29-Pad11)': input(s) U29.11 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor.

  8. FloatingInputmajorOpen

    FloatingInput: 4 nets×4

    e.g. “U16.1 on 'Net-(U16-Pad1)' has no driver and no pull” · 4 different statements

    At Net-(U16-Pad1), Net-(U16-Pad13), Net-(U16-Pad15), Net-(U16-Pad6)

    Each finding, with its own headline
    • Net-(U16-Pad1)U16.1 on 'Net-(U16-Pad1)' has no driver and no pull

      Net 'Net-(U16-Pad1)': input(s) U16.1 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor. U16.1 (N/C): the function NAME reads as a not-connect, which is a clue and not a fact, so the pin is kept. If the datasheet's type column says NC, file that cell (submit_pin_behavior pinType=nc, quoting the cell and citing the page) and the pin leaves this finding.

    • Net-(U16-Pad13)U16.13 on 'Net-(U16-Pad13)' has no driver and no pull

      Net 'Net-(U16-Pad13)': input(s) U16.13 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor. U16.13 (N/C): the function NAME reads as a not-connect, which is a clue and not a fact, so the pin is kept. If the datasheet's type column says NC, file that cell (submit_pin_behavior pinType=nc, quoting the cell and citing the page) and the pin leaves this finding.

    • Net-(U16-Pad15)U16.15 on 'Net-(U16-Pad15)' has no driver and no pull

      Net 'Net-(U16-Pad15)': input(s) U16.15 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor. U16.15 (N/C): the function NAME reads as a not-connect, which is a clue and not a fact, so the pin is kept. If the datasheet's type column says NC, file that cell (submit_pin_behavior pinType=nc, quoting the cell and citing the page) and the pin leaves this finding.

    • Net-(U16-Pad6)U16.6 on 'Net-(U16-Pad6)' has no driver and no pull

      Net 'Net-(U16-Pad6)': input(s) U16.6 with no driver and no pull — floating input (undefined level); add a driver or a pull resistor. U16.6 (N/C): the function NAME reads as a not-connect, which is a clue and not a fact, so the pin is kept. If the datasheet's type column says NC, file that cell (submit_pin_behavior pinType=nc, quoting the cell and citing the page) and the pin leaves this finding.

  9. PartLifecyclemajorOpen

    HMC1097LP4E on U16: the distributor catalogue reports "Obsolete" for Analog Devices Inc.'s HMC1097LP4E

    HMC1097LP4E on U16: the distributor catalogue reports "Obsolete" for Analog Devices Inc.'s HMC1097LP4E — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names Hittite, and that is one line with Analog Devices Inc.: Analog Devices completed its acquisitions of Hittite Microwave on 2014-07-22, Linear Technology on 2017-03-10 and Maxim Integrated on 2021-08-26. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/HMC1097LP4E/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2022-07-31, 1,568 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.

    At U16

  10. PartLifecyclemajorOpen

    PartLifecycle: 5 part numbers×5

    3 Not For New Designs, 1 Discontinued at DigiKey, 1 Obsolete · on 46 placements

    At C143, C146, C155, U14, U17

    Each finding, with its own headline
    • C143EEEFC1A101P on 3 placements (C143, C144, C145): the distributor catalogue reports "Not For New Designs" for Panasonic Industry's EEE-FC1A101P

      EEEFC1A101P on 3 placements (C143, C144, C145): the distributor catalogue reports "Not For New Designs" for Panasonic Industry's EEE-FC1A101P — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (Panasonic). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/EEEFC1A101P/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • C146C2012X5R1C106K085AC on 35 placements (C146, C147, C151, C152, C153, C154, C158, C159, …): the distributor catalogue reports "Not For New Designs" for TDK's C2012X5R1C106K085AC

      C2012X5R1C106K085AC on 35 placements (C146, C147, C151, C152, C153, C154, C158, C159, …): the distributor catalogue reports "Not For New Designs" for TDK's C2012X5R1C106K085AC — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (TDK). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/C2012X5R1C106K085AC/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • C155EEEFC1C100R on 3 placements (C155, C156, C157): the distributor catalogue reports "Not For New Designs" for Panasonic Industry's EEE-FC1C100R

      EEEFC1C100R on 3 placements (C155, C156, C157): the distributor catalogue reports "Not For New Designs" for Panasonic Industry's EEE-FC1C100R — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (Panasonic). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/EEEFC1C100R/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • U14LT6600CS8-2.5 on 2 placements (U14, U15): the distributor catalogue reports "Discontinued at DigiKey" for Analog Devices Inc.'s LT6600CS8-2.5

      LT6600CS8-2.5 on 2 placements (U14, U15): the distributor catalogue reports "Discontinued at DigiKey" for Analog Devices Inc.'s LT6600CS8-2.5 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names Linear Technology, and that is one line with Analog Devices Inc.: Analog Devices completed its acquisitions of Hittite Microwave on 2014-07-22, Linear Technology on 2017-03-10 and Maxim Integrated on 2021-08-26. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/LT6600CS8-2.5/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

    • U17GP2Y+ on 3 placements (U17, U25, U3): the distributor catalogue reports "Obsolete" for Mini-Circuits's GP2Y+

      GP2Y+ on 3 placements (U17, U25, U3): the distributor catalogue reports "Obsolete" for Mini-Circuits's GP2Y+ — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. That is the maker this board's BOM names (Mini-Circuits). A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/GP2Y+/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). No approved alternate is recorded for this position.

  11. ReferencePlaneDiscontinuitymajorOpen

    ReferencePlaneDiscontinuity: 30 boards×30

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: 87 split/void/reference-change sites read from the copper stand as reported; they are layout-practice findings with Probe's default limits, and no datasheet or app note on file sets one for these RF and control nets. Left for the owner.

    At refchange:3V3_1|GND, refchange:5V_1|GND, void:3V3_1@L6_PSU:140.97,-126.48, void:3V3_1@L6_PSU:144.96,-185.99, void:3V3_1@L6_PSU:198.38,-111.65, void:3V3_1@L6_PSU:202.61,-131.78 and 24 more

    Each finding, with its own headline
    • refchange:3V3_1|GND14 nets change reference between 3V3_1 and GND at 34 vias; 22 of them partial (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      At 34 via(s), on 14 net(s), the signal leaves a layer referenced by one of 3V3_1 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 7 served, 27 with none. 34 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether 3V3_1 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. 22 of them are partial: another reference continues across through a stitching via of its net, so only part of the return has nowhere to go. The pure ones are listed first, then the partial ones with the farthest stitching via first.

      • '/TOP/PLL/PLL_LOCKED' at (235.62, -116.59), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.46 mm away; stitching none, 192.2 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC/ADC_ALARM' at (234.38, -111.1), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU; pure, no reference continues across; stitching none, 111.8 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC/ADC_ALARM' at (140.97, -122.86), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.93 mm away; stitching none, 111.8 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC/ADC_ALARM' at (142.33, -132.45), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.56 mm away; stitching none, 111.8 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC/ADC_MOSI' at (139.91, -136.47), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU; pure, no reference continues across; stitching none, 109.6 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC/ADC_MOSI' at (206.79, -107.3), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.95 mm away; stitching none, 109.6 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/PLL/PLL_ENout' at (214.05, -133.41), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU; pure, no reference continues across; stitching none, 109.5 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/PLL/PLL_ENout' at (147.89, -185.43), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.43 mm away; stitching none, 109.5 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/PLL/PLL_LE' at (202.72, -132.55), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.78 mm away; stitching none, 97.7 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/PLL/PLL_LE' at (151.41, -179.91), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.71 mm away; stitching none, 97.7 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC//ADC_RST' at (209.75, -109.39), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.82 mm away; stitching none, 96.9 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/ADC//ADC_RST' at (139.72, -135.54), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 3V3_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.37 mm away; stitching none, 96.9 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 3V3_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 22 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=refchange%3A3V3_1%7CGND serves each with its own layer_image region; all of them lie in x 131.43..237.62, y -187.43..-105.3 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • refchange:5V_1|GND14 nets change reference between 5V_1 and GND at 24 vias; 14 of them partial (fastest: /TOP/Frequency_dividers/FD0_BYP at 100 ps 10-90 %, ASSUMED)

      At 24 via(s), on 14 net(s), the signal leaves a layer referenced by one of 5V_1 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 5 served, 19 with none. 24 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether 5V_1 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. 14 of them are partial: another reference continues across through a stitching via of its net, so only part of the return has nowhere to go. The pure ones are listed first, then the partial ones with the farthest stitching via first.

      • '/TOP/Frequency_dividers/FD2_DIV1' at (233.28, -179.39), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.62 mm away; stitching none, 83.2 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD0_BYP' at (208.6, -168.46), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.37 mm away; stitching none, 77.5 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD2_BYP' at (233.28, -183.59), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.23 mm away; stitching none, 76.5 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD0_N1' at (206.63, -167.93), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.89 mm away; stitching none, 75.7 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD0_N0' at (204.02, -166.85), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.63 mm away; stitching none, 61.9 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD1_N0' at (231.38, -170.07), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.65 mm away; stitching none, 53.4 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD1_N1' at (231.44, -169.32), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 2.66 mm away; stitching none, 40.2 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • '/TOP/Frequency_dividers/FD0_DIV1' at (209.92, -172.67), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU, GND on L8_BOTTOM; partial, GND continues through a via of GND 1.38 mm away; stitching none, 20.3 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'Net-(R138-Pad2)' at (240.77, -146.37), L7_DIGITAL -> L8_BOTTOM: 5V_1 on L6_PSU, GND on L8_BOTTOM to GND on L7_DIGITAL; partial, GND continues through a via of GND 4.03 mm away; stitching none, 16.4 mm of track past the via on L8_BOTTOM: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'Net-(R132-Pad2)' at (240.11, -134.43), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU; pure, no reference continues across; stitching none, 12.9 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'Net-(R134-Pad2)' at (239.95, -133.42), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU; pure, no reference continues across; stitching none, 10.5 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • 'Net-(U35-Pad8)' at (240.52, -107.97), L1_TOP-RO4350_B -> L7_DIGITAL: GND on L2_GND to 5V_1 on L6_PSU; pure, no reference continues across; stitching none, 10.3 mm of track past the via on L7_DIGITAL: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. 5V_1 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
      • and 12 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=refchange%3A5V_1%7CGND serves each with its own layer_image region; all of them lie in x 202.02..253.71, y -190.09..-105.97 mm (board frame, Y up).

      The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:140.97,-126.48'/TOP/ADC/ADC_ALARM' crosses where the outline of the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 3.73 mm; 1 cleared on both sides of the track (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/ADC_ALARM' on L7_DIGITAL, the GND plane on L8_BOTTOM has 3.73 mm under the track with no copper, at (140.97, -127.68), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.47 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 2 reference layers: '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (140.97, -126.48), 1.34 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (140.97, -127.68), 3.73 mm, running ALONG the bare copper for 2.47 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A140.97%2C-126.48 serves each with its own layer_image region; all of them lie in x 139.97..141.97, y -130.54..-124.81 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:144.96,-185.99'/TOP/PLL/PLL_LOCKED' crosses where the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back round copper of 3V3_1, Net-(C15-Pad1), at 1 place, the longest 4.87 mm; 1 cleared on both sides of the track (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 4.87 mm under the track with copper of Net-(C15-Pad1), 3V3_1, not a plane, at (144.4, -188.62), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.08 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 2 reference layers: '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (144.96, -185.99), 1.31 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (144.4, -188.62), 4.87 mm, running ALONG the bare copper for 2.08 mm, not across it over copper of Net-(C15-Pad1), 3V3_1, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A144.96%2C-185.99 serves each with its own layer_image region; all of them lie in x 142.58..146.35, y -190.44..-183.88 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:198.38,-111.653 nets cross where the 3V3_1 plane on L6_PSU, the GND plane on L7_DIGITAL and the GND plane on L8_BOTTOM is drawn back round copper of /TOP/ADC//ADC_CS, Net-(R128-Pad2), Net-(R130-Pad1), Net-(R131-Pad1), at 1 place, the longest 8.64 mm (fastest: Net-(R128-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC//ADC_CS' on L7_DIGITAL, the GND plane on L8_BOTTOM has 8.64 mm under the track with copper of Net-(R128-Pad2), GND, not a plane, at (202.96, -111.34), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 5.11 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 and of the pour at x 141.01..205.71, y -118.81..-111.95 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 2 of the 4 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 4 reference layers: '/TOP/ADC//ADC_CS' on L7_DIGITAL at (198.38, -111.65), 1.6 mm over no copper; other side: GND on L8_BOTTOM, 0.13 mm from the track against 0.13 mm to L6_PSU: 50% of the return on L6_PSU / '/TOP/ADC//ADC_CS' on L7_DIGITAL at (202.96, -111.34), 8.64 mm, running ALONG the bare copper for 5.11 mm, not across it over copper of Net-(R128-Pad2), GND, not a plane; other side: no plane on L6_PSU / 'Net-(R128-Pad2)' on L8_BOTTOM at (203.58, -113.63), 6.75 mm, running ALONG the bare copper for 1.6 mm, not across it over copper of /TOP/ADC//ADC_CS, Net-(R131-Pad1), Net-(R130-Pad1), not a plane; other side: none: the signal layer is outermost / 'Net-(R130-Pad1)' on L7_DIGITAL at (203.94, -115.02), 1.58 mm over copper of Net-(R128-Pad2), not a plane, to the end of the track; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A198.38%2C-111.65 serves each with its own layer_image region; all of them lie in x 197.08..207.76, y -116.53..-109.26 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:202.61,-131.78'/TOP/PLL/PLL_CE' crosses where the outline of the 3V3_1 plane on L6_PSU is drawn back, at 1 place, the longest 0.48 mm (fastest: /TOP/PLL/PLL_CE at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_CE' on L7_DIGITAL, the 3V3_1 plane on L6_PSU has 0.48 mm under the track with no copper, at (202.61, -131.78), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_CE' on L7_DIGITAL at (202.61, -131.78), 0.48 mm over no copper; other side: no plane on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A202.61%2C-131.78 serves each with its own layer_image region; all of them lie in x 201.37..203.85, y -132.78..-130.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:5V_1@L6_PSU:223.69,-154.793 nets cross where the 5V_1 plane on L6_PSU, the GND plane on L7_DIGITAL and the GND plane on L8_BOTTOM is drawn back round copper of /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD0_N1, /TOP/Frequency_dividers/FD1_BYP, at 1 place, the longest 35.02 mm (fastest: /TOP/Frequency_dividers/FD0_BYP at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD0_N1' on L7_DIGITAL, the 5V_1 plane on L6_PSU has 35.02 mm under the track with no copper, at (223.69, -154.79), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 30.6 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 204.91..258.72, y -196.66..-76.84 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 4 of the 5 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 5 reference layers: '/TOP/Frequency_dividers/FD0_BYP' on L7_DIGITAL at (223.74, -155.46), 33.97 mm, running ALONG the bare copper for 30.5 mm, not across it over no copper; other side: GND on L8_BOTTOM, 0.13 mm from the track against 0.13 mm to L6_PSU: 50% of the return on L6_PSU / '/TOP/Frequency_dividers/FD0_BYP' on L7_DIGITAL at (240.39, -155.46), 1.23 mm over copper of /TOP/Frequency_dividers/FD1_BYP, not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD0_N1' on L7_DIGITAL at (223.69, -154.79), 35.02 mm, running ALONG the bare copper for 30.6 mm, not across it over no copper; other side: GND on L8_BOTTOM, 0.13 mm from the track against 0.13 mm to L6_PSU: 50% of the return on L6_PSU / '/TOP/Frequency_dividers/FD0_N1' on L7_DIGITAL at (240.39, -154.79), 1.23 mm over copper of /TOP/Frequency_dividers/FD1_BYP, not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD1_BYP' on L8_BOTTOM at (240.03, -154.43), 2.01 mm over copper of /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD0_N1, not a plane; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A5V_1%40L6_PSU%3A223.69%2C-154.79 serves each with its own layer_image region; all of them lie in x 204.48..241.65, y -158.16..-153.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:5V_1@L6_PSU:250.5,-132.069 nets cross where the 5V_1 plane on L6_PSU, the GND plane on L7_DIGITAL and the GND plane on L8_BOTTOM is drawn back round copper of /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD0_N1, /TOP/Frequency_dividers/FD1_N0, /TOP/Frequency_dividers/FD1_N1, /TOP/Frequency_dividers/FD2_BYP, /TOP/Frequency_dividers/FD2_DIV1, /TOP/digital_interface/FD_ENC, 3V3_2, 5V_1, Net-(R140-Pad2), Net-(R142-Pad2), Net-(R144-Pad2), at 1 place, the longest 15.59 mm (fastest: /TOP/Frequency_dividers/FD0_BYP at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R142-Pad2)' on L8_BOTTOM, the GND plane on L7_DIGITAL has 15.59 mm under the track with copper of /TOP/Frequency_dividers/FD2_BYP, /TOP/Frequency_dividers/FD2_DIV1, /TOP/Frequency_dividers/FD1_N0, /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD0_N1, not a plane, at (253.36, -135.67), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 7 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 11.96 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 204.91..258.72, y -196.66..-76.84 and of the pour at x 241.04..251.1, y -134.71..-129.88 and of the pour at x 247.12..252.27, y -131.48..-130.52 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 6 of the 14 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one stretch, cleared on 14 reference layers: '/TOP/Frequency_dividers/FD0_BYP' on L7_DIGITAL at (250.48, -140.17), 4.89 mm over copper of Net-(R140-Pad2), Net-(R142-Pad2), not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD0_N1' on L7_DIGITAL at (250.06, -140.17), 4.89 mm over copper of Net-(R140-Pad2), Net-(R142-Pad2), not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD1_N0' on L7_DIGITAL at (251.86, -140.16), 5.17 mm over copper of Net-(R142-Pad2), Net-(R140-Pad2), not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD1_N0' on L7_DIGITAL at (251.86, -144.4), 1.89 mm over copper of /TOP/Frequency_dividers/FD1_N1, not a plane; other side: no plane on L6_PSU / '/TOP/Frequency_dividers/FD1_N0' on L8_BOTTOM at (249.85, -129.26), 4.2 mm, running ALONG the bare copper for 3 mm, not across it over copper of /TOP/Frequency_dividers/FD2_BYP, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/TOP/Frequency_dividers/FD1_N1' on L8_BOTTOM at (253.24, -142.43), 3.08 mm over copper of /TOP/Frequency_dividers/FD2_BYP, /TOP/Frequency_dividers/FD2_DIV1, /TOP/Frequency_dividers/FD1_N0, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/TOP/Frequency_dividers/FD2_BYP' on L7_DIGITAL at (252.88, -136.03), 15.37 mm, running ALONG the bare copper for 11.96 mm, not across it over copper of Net-(R140-Pad2), Net-(R142-Pad2), /TOP/Frequency_dividers/FD1_N1, /TOP/Frequency_dividers/FD1_N0, not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (250.5, -132.06), 0.56 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (242.35, -131.51), 9.17 mm, running ALONG the bare copper for 4.61 mm, not across it over copper of Net-(R144-Pad2), /TOP/digital_interface/FD_ENC, Net-(R142-Pad2), Net-(R140-Pad2), GND, 3V3_2, 5V_1, not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (250.5, -132.06), 0.55 mm over no copper; other side: no plane on L6_PSU / '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (252.31, -135.09), 13.16 mm, running ALONG the bare copper for 9.54 mm, not across it over copper of /TOP/Frequency_dividers/FD1_N0, Net-(R140-Pad2), Net-(R142-Pad2), /TOP/Frequency_dividers/FD1_N1, not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / 'Net-(R140-Pad2)' on L8_BOTTOM at (252.61, -133.89), 11.52 mm, running ALONG the bare copper for 7.29 mm, not across it over copper of /TOP/Frequency_dividers/FD0_N1, /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD1_N0, /TOP/Frequency_dividers/FD2_DIV1, /TOP/Frequency_dividers/FD2_BYP, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'Net-(R142-Pad2)' on L8_BOTTOM at (253.36, -135.67), 15.59 mm, running ALONG the bare copper for 11.18 mm, not across it over copper of /TOP/Frequency_dividers/FD2_BYP, /TOP/Frequency_dividers/FD2_DIV1, /TOP/Frequency_dividers/FD1_N0, /TOP/Frequency_dividers/FD0_BYP, /TOP/Frequency_dividers/FD0_N1, not a plane; other side: none: the signal layer is outermost / 'Net-(R144-Pad2)' on L8_BOTTOM at (240.52, -128.89), 3.12 mm, running ALONG the bare copper for 0.76 mm, not across it over copper of /TOP/Frequency_dividers/FD2_DIV1, not a plane; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A5V_1%40L6_PSU%3A250.5%2C-132.06 serves each with its own layer_image region; all of them lie in x 237.59..254.5, y -145.84..-127.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:5V_2@L4_PSU:175.92,-199.76'/TOP/ADC/MIXERout1' crosses where the outline of the GND plane on L2_GND and the 5V_2 plane on L4_PSU is drawn back, at 1 place, the longest 0.97 mm; 1 cleared on both sides of the track (fastest: /TOP/ADC/MIXERout1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/MIXERout1' on L3_ANALOG, the 5V_2 plane on L4_PSU has 0.97 mm under the track with no copper, at (175.92, -199.76), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..238.86, y -206.64..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 2 reference layers: '/TOP/ADC/MIXERout1' on L3_ANALOG at (175.92, -199.76), 0.97 mm over no copper; other side: no plane on L4_PSU / '/TOP/ADC/MIXERout1' on L3_ANALOG at (175.92, -199.76), 0.97 mm over no copper; other side: no plane on L2_GND

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A5V_2%40L4_PSU%3A175.92%2C-199.76 serves each with its own layer_image region; all of them lie in x 174.57..177.26, y -201.1..-198.41 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:140.17,-137.63'Net-(R126-Pad2)' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 2.34 mm (fastest: Net-(R126-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R126-Pad2)' on L1_TOP-RO4350_B, the GND plane on L2_GND has 2.34 mm under the track with no copper, at (140.17, -137.63), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(R126-Pad2)' on L1_TOP-RO4350_B at (140.17, -137.63), 2.34 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A140.17%2C-137.63 serves each with its own layer_image region; all of them lie in x 138.78..141.4, y -138.82..-136.24 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:142.79,-180.34'Net-(C24-Pad1)' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.01 mm (fastest: Net-(C24-Pad1) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(C24-Pad1)' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.01 mm under the track with no copper, at (142.79, -180.34), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(C24-Pad1)' on L1_TOP-RO4350_B at (142.79, -180.34), 1.01 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A142.79%2C-180.34 serves each with its own layer_image region; all of them lie in x 141.28..144.29, y -181.34..-179.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:148.98,-177.13'Net-(R11-Pad1)' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 0.7 mm (fastest: Net-(R11-Pad1) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R11-Pad1)' on L1_TOP-RO4350_B, the GND plane on L2_GND has 0.7 mm under the track with no copper, at (148.98, -177.13), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(R11-Pad1)' on L1_TOP-RO4350_B at (148.98, -177.13), 0.7 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A148.98%2C-177.13 serves each with its own layer_image region; all of them lie in x 147.79..150.21, y -178.45..-175.95 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:152.15,-181.04'/TOP/PLL/PLL_DATA' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.51 mm (fastest: /TOP/PLL/PLL_DATA at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_DATA' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.51 mm under the track with no copper, at (152.15, -181.04), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_DATA' on L1_TOP-RO4350_B at (152.15, -181.04), 1.51 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A152.15%2C-181.04 serves each with its own layer_image region; all of them lie in x 150.18..153.44, y -182.34..-179.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:212.53,-174.19'Net-(C73-Pad2)' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.14 mm (fastest: Net-(C73-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(C73-Pad2)' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.14 mm under the track with no copper, at (212.53, -174.19), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(C73-Pad2)' on L1_TOP-RO4350_B at (212.53, -174.19), 1.14 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A212.53%2C-174.19 serves each with its own layer_image region; all of them lie in x 211.13..213.93, y -175.59..-172.78 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:224.57,-169.89'Net-(C81-Pad2)' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.38 mm (fastest: Net-(C81-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(C81-Pad2)' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.38 mm under the track with no copper, at (224.57, -169.89), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(C81-Pad2)' on L1_TOP-RO4350_B at (224.57, -169.89), 1.38 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A224.57%2C-169.89 serves each with its own layer_image region; all of them lie in x 223.07..226.13, y -171.28..-168.5 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:228.23,-185.63'/TOP/Frequency_dividers/FD2_N0' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/Frequency_dividers/FD2_N0 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_N0' on L1_TOP-RO4350_B, the GND plane on L2_GND has 0.5 mm under the track with no copper, at (228.23, -185.63), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/Frequency_dividers/FD2_N0' on L1_TOP-RO4350_B at (228.23, -185.63), 0.5 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A228.23%2C-185.63 serves each with its own layer_image region; all of them lie in x 227.23..229.34, y -186.8..-184.35 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:235.9,-111.99'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 2.14 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L1_TOP-RO4350_B, the GND plane on L2_GND has 2.14 mm under the track with no copper, at (235.9, -111.99), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_LOCKED' on L1_TOP-RO4350_B at (235.9, -111.99), 2.14 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A235.9%2C-111.99 serves each with its own layer_image region; all of them lie in x 234.62..238.18, y -113.41..-110.71 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:231.76,-72.78'Net-(C142-Pad1)' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 1.05 mm (fastest: Net-(C142-Pad1) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(C142-Pad1)' on L8_BOTTOM, the GND plane on L7_DIGITAL has 1.05 mm under the track with no copper, at (231.76, -72.78), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(C142-Pad1)' on L8_BOTTOM at (231.76, -72.78), 1.05 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A231.76%2C-72.78 serves each with its own layer_image region; all of them lie in x 230.76..232.76, y -74.3..-71.26 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:239.8,-127.91'Net-(R149-Pad2)' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 2.22 mm (fastest: Net-(R149-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R149-Pad2)' on L8_BOTTOM, the GND plane on L7_DIGITAL has 2.22 mm under the track with no copper, at (239.8, -127.91), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.99 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • 'Net-(R149-Pad2)' on L8_BOTTOM at (239.8, -127.91), 2.22 mm, running ALONG the bare copper for 0.99 mm, not across it over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A239.8%2C-127.91 serves each with its own layer_image region; all of them lie in x 238.1..242.08, y -128.91..-126.33 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:240.6,-145.36'/TOP/Frequency_dividers/FD1_BYP' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 2.48 mm (fastest: /TOP/Frequency_dividers/FD1_BYP at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_BYP' on L8_BOTTOM, the GND plane on L7_DIGITAL has 2.48 mm under the track with no copper, at (240.6, -145.36), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.66 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/Frequency_dividers/FD1_BYP' on L8_BOTTOM at (240.6, -145.36), 2.48 mm, running ALONG the bare copper for 1.66 mm, not across it over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A240.6%2C-145.36 serves each with its own layer_image region; all of them lie in x 239.03..242.17, y -147.79..-143.79 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:243.18,-138.35'/TOP/Frequency_dividers/FD1_BYP' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 5.57 mm (fastest: /TOP/Frequency_dividers/FD1_BYP at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_BYP' on L8_BOTTOM, the GND plane on L7_DIGITAL has 5.57 mm under the track with no copper, at (243.18, -138.35), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 4.21 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/Frequency_dividers/FD1_BYP' on L8_BOTTOM at (243.18, -138.35), 5.57 mm, running ALONG the bare copper for 4.21 mm, not across it over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A243.18%2C-138.35 serves each with its own layer_image region; all of them lie in x 241..246.69, y -140.53..-134.8 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:250.59,-127.31'/TOP/Frequency_dividers/FD1_N1' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 0.9 mm (fastest: /TOP/Frequency_dividers/FD1_N1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_N1' on L8_BOTTOM, the GND plane on L7_DIGITAL has 0.9 mm under the track with no copper, at (250.59, -127.31), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.53 mm). No hole cleared it: the outline of the pour at x 246.73..252, y -128.31..-127.28 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/Frequency_dividers/FD1_N1' on L8_BOTTOM at (250.59, -127.31), 0.9 mm, running ALONG the bare copper for 0.53 mm, not across it over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A250.59%2C-127.31 serves each with its own layer_image region; all of them lie in x 249.14..252.04, y -128.31..-126.31 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:144.94,-184.13'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.88 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.88 mm under the track with no copper, at (144.94, -184.13), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (144.94, -184.13), 0.88 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A144.94%2C-184.13 serves each with its own layer_image region; all of them lie in x 143.94..145.94, y -185.57..-182.69 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:224.33,-122.18'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (224.33, -122.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (224.33, -122.18), 0.5 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A224.33%2C-122.18 serves each with its own layer_image region; all of them lie in x 223.08..225.59, y -123.18..-121.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:224.34,-118.45'/TOP/ADC/ADC_ALARM' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.51 mm (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/ADC_ALARM' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.51 mm under the track with no copper, at (224.34, -118.45), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (224.34, -118.45), 0.51 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A224.34%2C-118.45 serves each with its own layer_image region; all of them lie in x 223.08..225.59, y -119.45..-117.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:225.27,-118.45'/TOP/ADC/ADC_ALARM' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/ADC_ALARM' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (225.27, -118.45), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (225.27, -118.45), 0.5 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A225.27%2C-118.45 serves each with its own layer_image region; all of them lie in x 224.02..226.52, y -119.45..-117.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:225.27,-122.18'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (225.27, -122.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (225.27, -122.18), 0.5 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A225.27%2C-122.18 serves each with its own layer_image region; all of them lie in x 224.02..226.52, y -123.18..-121.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:228.03,-122.18'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 4.65 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 4.65 mm under the track with no copper, at (228.03, -122.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 3.35 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (228.03, -122.18), 4.65 mm, running ALONG the bare copper for 3.35 mm, not across it over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A228.03%2C-122.18 serves each with its own layer_image region; all of them lie in x 225.03..231.49, y -123.18..-120.72 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:235.44,-169.06'/TOP/Frequency_dividers/FD1_N1' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.39 mm (fastest: /TOP/Frequency_dividers/FD1_N1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.39 mm under the track with no copper, at (235.44, -169.06), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL at (235.44, -169.06), 0.39 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A235.44%2C-169.06 serves each with its own layer_image region; all of them lie in x 234.25..236.64, y -170.06..-168.06 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:routed@L7_DIGITAL|L8_BOTTOMTracks on L7_DIGITAL and L8_BOTTOM cross each other at 22 places, each layer the other's reference with its pour cleared round its own tracks, the longest 11.17 mm; 18 run ALONG the cut round another net's track (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      L7_DIGITAL and L8_BOTTOM each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 22 place(s) on 41 net(s), 14 of them seen from both tracks (each counted once). 18 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 3.78 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 15 of the 57 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.

      • one crossing of two tracks, seen from each: '/TOP/digital_interface/FD0_N0-N' on L8_BOTTOM at (232.18, -132.41), 1.52 mm over copper of /TOP/digital_interface/FD_ENA, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD0_N0-P' on L8_BOTTOM at (232.5, -132.91), 1.25 mm over copper of /TOP/digital_interface/FD_ENA, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_BYP-N' on L8_BOTTOM at (230.63, -131.33), 1.25 mm over copper of /TOP/digital_interface/FD_ENA, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_BYP-P' on L8_BOTTOM at (230.66, -131.83), 1.69 mm over copper of /TOP/digital_interface/FD_ENA, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_N0-N' on L8_BOTTOM at (232.26, -128.91), 2.37 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_N0-P' on L8_BOTTOM at (231.46, -129.41), 2.37 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_N1-N' on L8_BOTTOM at (232.29, -129.91), 2.22 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD1_N1-P' on L8_BOTTOM at (231.76, -130.41), 2.33 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane, to the end of the track; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD2_BYP-P' on L8_BOTTOM at (232.26, -127.91), 2.37 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost / '/TOP/digital_interface/FD_ENA' on L7_DIGITAL at (233.66, -134.4), 11.17 mm over copper of /TOP/digital_interface/FD0_N1-N, GND, /TOP/digital_interface/FD0_N0-P, /TOP/digital_interface/FD0_N0-N, /TOP/digital_interface/FD1_BYP-P, /TOP/digital_interface/FD1_BYP-N, /TOP/digital_interface/FD1_N1-P, /TOP/digital_interface/FD1_N1-N, /TOP/digital_interface/FD1_N0-P, /TOP/digital_interface/FD1_N0-N, /TOP/digital_interface/FD2_BYP-P, /TOP/digital_interface/FD2_BYP-N, /TOP/digital_interface/FD2_DIV1-P, /TOP/digital_interface/FD2_DIV1-N, not a plane, to the end of the track; other side: no plane on L6_PSU
      • one crossing of two tracks, seen from each: 'Net-(R132-Pad2)' on L7_DIGITAL at (242.68, -132.79), 5.52 mm, running ALONG the bare copper for 2.76 mm, not across it over copper of Net-(R136-Pad2), Net-(R138-Pad2), GND, Net-(R134-Pad2), not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / 'Net-(R134-Pad2)' on L7_DIGITAL at (242.68, -133.4), 5.44 mm, running ALONG the bare copper for 3.01 mm, not across it over copper of Net-(R138-Pad2), Net-(R136-Pad2), not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / 'Net-(R136-Pad2)' on L8_BOTTOM at (239.53, -132.41), 2.65 mm over copper of Net-(R134-Pad2), Net-(R132-Pad2), not a plane; other side: none: the signal layer is outermost / 'Net-(R138-Pad2)' on L8_BOTTOM at (243.76, -133.44), 7.31 mm, running ALONG the bare copper for 3.78 mm, not across it over copper of Net-(R134-Pad2), Net-(R132-Pad2), not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/Frequency_dividers/FD2_BYP' on L8_BOTTOM at (243.2, -129.91), 0.91 mm, running ALONG the bare copper for 0.79 mm, not across it over copper of Net-(R140-Pad2), not a plane, to the end of the track; other side: none: the signal layer is outermost / 'Net-(R140-Pad2)' on L7_DIGITAL at (244.44, -127.33), 6.18 mm, running ALONG the bare copper for 2.64 mm, not across it over copper of /TOP/Frequency_dividers/FD2_BYP, Net-(R144-Pad2), GND, Net-(R149-Pad2), not a plane, to the end of the track; other side: no plane on L6_PSU / 'Net-(R140-Pad2)' on L7_DIGITAL at (246.74, -126.93), 2.81 mm over copper of Net-(R144-Pad2), not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / 'Net-(R144-Pad2)' on L8_BOTTOM at (243.79, -129.26), 1.69 mm over copper of Net-(R140-Pad2), not a plane; other side: none: the signal layer is outermost / 'Net-(R144-Pad2)' on L8_BOTTOM at (246.38, -126.79), 1.57 mm over copper of Net-(R140-Pad2), not a plane; other side: none: the signal layer is outermost / 'Net-(R149-Pad2)' on L8_BOTTOM at (244.33, -127.31), 2.37 mm, running ALONG the bare copper for 0.58 mm, not across it over copper of Net-(R140-Pad2), not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/PLL/PLL_CE' on L8_BOTTOM at (148.46, -166.88), 4.73 mm, running ALONG the bare copper for 2.76 mm, not across it over copper of /TOP/PLL/PLL_LOCKED, not a plane; other side: none: the signal layer is outermost / '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (148.55, -166.93), 4.71 mm, running ALONG the bare copper for 2.98 mm, not across it over copper of /TOP/PLL/PLL_CE, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM
      • one crossing of two tracks, seen from each: '/TOP/DAC/DAC_MISO' on L7_DIGITAL at (234.78, -102.82), 4.48 mm, running ALONG the bare copper for 3.33 mm, not across it over copper of Net-(R153-Pad2), not a plane; other side: no plane on L6_PSU / 'Net-(R153-Pad2)' on L8_BOTTOM at (234.48, -102.83), 4.58 mm, running ALONG the bare copper for 2.83 mm, not across it over copper of /TOP/DAC/DAC_MISO, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (136.81, -132.1), 3.73 mm, running ALONG the bare copper for 1.86 mm, not across it over copper of Net-(R126-Pad2), 3V3_2, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (138.87, -136.09), 1.25 mm over copper of Net-(R126-Pad2), not a plane, to the end of the track; other side: no plane on L6_PSU / 'Net-(R126-Pad2)' on L8_BOTTOM at (136.45, -132.82), 1.17 mm over copper of /TOP/ADC/ADC_MOSI, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'Net-(R126-Pad2)' on L8_BOTTOM at (138.05, -135.41), 4.5 mm, running ALONG the bare copper for 1.54 mm, not across it over copper of /TOP/ADC/ADC_MOSI, not a plane, to the end of the track; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/ADC//ADC_CS' on L7_DIGITAL at (191.8, -112.12), 1.22 mm over copper of /TOP/DAC/DAC_MOSI, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/ADC//ADC_RST' on L7_DIGITAL at (191.8, -110.84), 1.36 mm over copper of /TOP/DAC/DAC_MOSI, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (191.8, -109.01), 1.22 mm over copper of /TOP/DAC/DAC_MOSI, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (191.8, -109.38), 1.22 mm over copper of /TOP/DAC/DAC_MOSI, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / '/TOP/DAC/DAC_MOSI' on L8_BOTTOM at (191.44, -110.11), 4.33 mm over copper of /TOP/ADC/ADC_MOSI, /TOP/ADC/ADC_SCK, /TOP/ADC//ADC_RST, /TOP/ADC//ADC_CS, not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/Frequency_dividers/FD2_BYP' on L8_BOTTOM at (246.12, -129.91), 2.09 mm over copper of Net-(R142-Pad2), not a plane, to the end of the track; other side: none: the signal layer is outermost / 'Net-(R142-Pad2)' on L7_DIGITAL at (246.14, -129.2), 3.68 mm, running ALONG the bare copper for 1.66 mm, not across it over copper of /TOP/Frequency_dividers/FD2_BYP, not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM
      • one crossing of two tracks, seen from each: '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (233.72, -111.76), 2.18 mm over copper of /TOP/digital_interface/D_ENA, not a plane, to the end of the track; other side: no plane on L6_PSU / '/TOP/ADC/ADC_MISO' on L7_DIGITAL at (233.95, -112.67), 1.41 mm over copper of /TOP/digital_interface/D_ENA, not a plane, to the end of the track; other side: no plane on L6_PSU / '/TOP/digital_interface/D_ENA' on L8_BOTTOM at (234.92, -112.33), 2.91 mm over copper of /TOP/ADC/ADC_ALARM, /TOP/ADC/ADC_MISO, not a plane; other side: none: the signal layer is outermost
      • one crossing of two tracks, seen from each: '/TOP/Frequency_dividers/FD1_N1' on L8_BOTTOM at (252.97, -127.93), 1.67 mm over copper of Net-(R140-Pad2), not a plane; other side: none: the signal layer is outermost / 'Net-(R140-Pad2)' on L7_DIGITAL at (252.61, -128.11), 2.45 mm over copper of /TOP/Frequency_dividers/FD1_N1, Net-(R142-Pad2), not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM / 'Net-(R142-Pad2)' on L8_BOTTOM at (251.92, -128.61), 2.62 mm, running ALONG the bare copper for 1.34 mm, not across it over copper of Net-(R140-Pad2), not a plane, to the end of the track; other side: none: the signal layer is outermost
      • '/TOP/digital_interface/FD2_DIV1-P' on L8_BOTTOM at (231.41, -126.6), 2.58 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost
      • '/TOP/digital_interface/FD2_BYP-N' on L8_BOTTOM at (231.32, -127.19), 2.37 mm over copper of /TOP/digital_interface/FD_ENA, /TOP/digital_interface/FD_ENB, not a plane; other side: none: the signal layer is outermost
      • and 10 more

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3Arouted%40L7_DIGITAL%7CL8_BOTTOM serves each with its own layer_image region; all of them lie in x 135.19..254.36, y -168.49..-101.82 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

  12. observationOBS-163minorOpen

    DAC reference is the shared 5V_2 LDO rail: LTC2758 RINA/RINB and ROFSA/ROFSB tie straight to 5V_2, which also carries the 170 mA HMC1097 modulator

    The LTC2758 DAC (U4) takes its reference and offset straight from the shared 5V_2 LDO rail, which also carries the 170 mA HMC1097 modulator.

    Where it is

    U4 LTC2758 (18-bit DAC) takes its reference from its REF inverting amplifiers (U5/U6 LT1012) fed through RINA and RINB, and its bipolar offset from ROFSA and ROFSB. All eight pins, plus VDD (pin 16), are on 5V_2:

    • RINA pins 5, 6 and RINB pins 31, 32
    • ROFSA pins 47, 48 and ROFSB pins 37, 38

    ``mermaid flowchart LR L["U40 TPS7A4700<br/>5V_2"] --> D["U4 LTC2758<br/>RINA/RINB, ROFSA/ROFSB"] L --> H["U16 HMC1097<br/>Vcc1 + Vcc2 170 mA"] L --> F["U14/U15 LT6600"] L --> A["U29 ADS8694 AVDD"] L --> R["U12/U13/U30 LTC6655 VIN"] ``

    What the references are used for

    The board has LTC6655 precision references, but only for the LT6600 VOCM bias (U12/U13) and the ADC (U30), not for the DAC. The LTC2758 datasheet (p.15) warns: 'not use voltages divided down from power supplies'.

  13. observationOBS-164minorOpen

    Two RF LDOs run hot: U39 (7V5 to 5V_1, three HMC705 at 190 mA each) about 1.4 W, and U44 (-24V to -5V) 1.3-1.6 W, junction rise 45-53 C

    Two RF LDOs run hot: U39 (7V5 to 5V_1) dissipates about 1.4 W and U44 (-24V to -5V) 1.3-1.6 W, a junction rise of 42-53 C above ambient, inside a closed die-cast box.

    The board sits in a closed Hammond 1590Q die-cast box (BOX1).

    U39 TPS7A4700, 7V5 to 5V_1

    QuantityValueSource
    Load: three HMC705 dividers U18-U20 (pins 9, 19)190 mA typical each, 570 mA totalHMC705 datasheet ("total supply current 190 mA"), p.1; netlist
    Other loadstwo SN74LV4T125 (U36/U37.14), D2 LED via R154netlist
    Dissipation, 2.5 V dropabout 1.43 Wderived
    theta-JA32.5 C/Wdatasheet, p.5
    Junction riseabout 46 C above ambientderived

    U44 TPS7A3301, -24V to -5V

    QuantityValueSource
    Drop19 Vderived
    Loadstwo LT6600-2.5 U14/U15 (28 mA typ, 36 mA max each at ±5 V), LTC6241 (2.4 mA), OPA2209 (2 × 2.5 mA), two LTC2054, D7 LED via R163LT6600 datasheet ("28 36 mA V = ±5V"), p.3; netlist
    Total load66-83 mAderived
    Dissipation1.3-1.6 Wderived
    theta-JA33.7 C/Wdatasheet, p.5
    Junction rise42-53 C above ambientderived
  14. observationOBS-165minorOpen

    No fiducials on either side of the RF board, which carries 0.5 mm-pitch QFN parts (HMC1097, HMC705 x3, LMX2541, TPS7A x7) and a 0.5 mm QSH connector

    The RF board has no fiducials on either side, although it carries 0.5 mm-pitch QFN parts and a 0.5 mm QSH connector.

    pcb/RF/TimIQ_RF.kicad_pcb has 467 footprints and none is a fiducial. The only non-electrical footprints are FIX1-FIX8 (3 mm holes, SOLEIL-D_3mm1), TP1-TP9 (SOLEIL-TEST-22) and logos.

    Fine-pitch parts:

    • U1 LMX2541 (36-WQFN)
    • U16 HMC1097 and U18-U20 HMC705 (LP4 QFN)
    • U39-U45 TPS7A (VQFN-20)
    • J5 Samtec QSH-040 (0.5 mm)
  15. observationOBS-166minorOpen

    RF silkscreen: J5, J6 and U34 designators sit under their own bodies; C139 silk crosses the FIX7 ground pad (0.48 mm pad gap); C193 and R154 designators print on J5 / FIX5 pads

    RF board silkscreen: the J5, J6 and U34 designators sit under their own bodies, C139 silk crosses the FIX7 ground pad (0.48 mm pad gap), and the C193 and R154 designators print on J5 / FIX5 pads.

    Measured from pcb/RF/TimIQ_RF.kicad_pcb. All 464 visible designators are 1.0 mm tall with a 0.15 mm stroke, and none overlaps another.

    • Under the body: the reference texts of J5 (QSH-040), J6 (Mini-Fit) and U34 (LVDT388A) are centred inside their own pad field.
    • C139: its bottom-side silk crosses the FIX7 mounting-hole pad 1 (GND), and C139 pad 2 is 0.481 mm from that pad.
    • On pads: the C193 designator overlaps a J5 mounting pad; the R154 designator overlaps FIX5 pad 1.
  16. DecapViaFanoutminorOpen

    DecapViaFanout: 20 components×20

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: 29 fan-out lengths read from the copper stand; the 0.5 nH limit is Probe's starting value, not a TPS7A or RF-part requirement, and no PDN target is stated. Left for the owner.

    At C140, C151, C162, C176, C181, C186 and 14 more

    Each finding, with its own headline
    • C140C140 on '7V5': its rail pad reaches its via over 1.84 mm of track, adding about 0.53 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C140 on '7V5': its rail pad reaches its via over 1.84 mm of track, adding about 0.53 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C140.1 (rail) runs 1.84 mm along its copper to its nearest via, 0.84 mm past the 1 mm beside the pad: 0.53 nH; C140.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 3.00 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.53 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.39 nH (pad 0.20 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.65 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C151C151 on '5V_1': its rail pad reaches its via over 4.52 mm of track and its ground pad over 0.00 mm, adding about 1.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C151 on '5V_1': its rail pad reaches its via over 4.52 mm of track and its ground pad over 0.00 mm, adding about 1.99 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C151.1 (rail) runs 4.52 mm along its copper to its nearest via, 3.52 mm past the 1 mm beside the pad: 1.99 nH; C151.2 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.99 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C162C162 on '7V5': its ground pad over 1.95 mm, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C162 on '7V5': its ground pad over 1.95 mm, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C162.1 (rail) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure; C162.2 (ground) runs 1.95 mm along its copper to its nearest via, 0.95 mm past the 1 mm beside the pad: 0.54 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.54 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.05 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.39 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C176C176 on '3V3_2': its rail pad reaches its via over 2.07 mm of track and its ground pad over 0.00 mm, adding about 0.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C176 on '3V3_2': its rail pad reaches its via over 2.07 mm of track and its ground pad over 0.00 mm, adding about 0.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C176.1 (rail) runs 2.07 mm along its copper to its nearest via, 1.07 mm past the 1 mm beside the pad: 0.61 nH; C176.2 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.61 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C181C181 on '3V3_2': its rail pad reaches its via over 2.14 mm of track and its ground pad over 0.00 mm, adding about 0.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C181 on '3V3_2': its rail pad reaches its via over 2.14 mm of track and its ground pad over 0.00 mm, adding about 0.65 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C181.1 (rail) runs 2.14 mm along its copper to its nearest via, 1.14 mm past the 1 mm beside the pad: 0.65 nH; C181.2 (ground) runs 0.00 mm along its copper to its nearest via, beside the pad. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.65 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C186C186 on '-5V': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C186 on '-5V': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C186.1 (rail) runs 1.50 mm along its copper to its nearest via, 0.50 mm past the 1 mm beside the pad: 0.28 nH; C186.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C187C187 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.61 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C187 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.61 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C187.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C187.2 (ground) runs 1.61 mm along its copper to its nearest via, 0.61 mm past the 1 mm beside the pad: 0.35 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C189C189 on '3V3_2': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.72 mm, adding about 0.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C189 on '3V3_2': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.72 mm, adding about 0.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C189.1 (rail) runs 1.50 mm along its copper to its nearest via, 0.50 mm past the 1 mm beside the pad: 0.28 nH; C189.2 (ground) runs 1.72 mm along its copper to its nearest via, 0.72 mm past the 1 mm beside the pad: 0.41 nH. Each run past the pad as one conductor of a pair 2.15 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.69 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C190C190 on '15V': its rail pad reaches its via over 3.41 mm of track, adding about 1.37 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C190 on '15V': its rail pad reaches its via over 3.41 mm of track, adding about 1.37 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C190.1 (rail) runs 3.41 mm along its copper to its nearest via, 2.41 mm past the 1 mm beside the pad: 1.37 nH; C190.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 1.37 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.05 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.39 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C191C191 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C191 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C191.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C191.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C192C192 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.61 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C192 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.61 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C192.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C192.2 (ground) runs 1.61 mm along its copper to its nearest via, 0.61 mm past the 1 mm beside the pad: 0.35 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C196C196 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.70 mm, adding about 0.67 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C196 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.70 mm, adding about 0.67 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C196.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C196.2 (ground) runs 1.70 mm along its copper to its nearest via, 0.70 mm past the 1 mm beside the pad: 0.40 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.67 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C197C197 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C197 on '-15V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C197.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C197.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C198C198 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C198 on '-5V': its rail pad reaches its via over 1.49 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C198.1 (rail) runs 1.49 mm along its copper to its nearest via, 0.49 mm past the 1 mm beside the pad: 0.28 nH; C198.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C199C199 on '-15V': its rail pad reaches its via over 1.52 mm of track and its ground pad over 1.60 mm, adding about 0.63 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C199 on '-15V': its rail pad reaches its via over 1.52 mm of track and its ground pad over 1.60 mm, adding about 0.63 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C199.1 (rail) runs 1.52 mm along its copper to its nearest via, 0.52 mm past the 1 mm beside the pad: 0.29 nH; C199.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.63 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C200C200 on '-5V': its rail pad reaches its via over 1.51 mm of track and its ground pad over 1.71 mm, adding about 0.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C200 on '-5V': its rail pad reaches its via over 1.51 mm of track and its ground pad over 1.71 mm, adding about 0.69 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C200.1 (rail) runs 1.51 mm along its copper to its nearest via, 0.51 mm past the 1 mm beside the pad: 0.29 nH; C200.2 (ground) runs 1.71 mm along its copper to its nearest via, 0.71 mm past the 1 mm beside the pad: 0.40 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.69 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.98 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C201C201 on '-15V': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves)

      C201 on '-15V': its rail pad reaches its via over 1.50 mm of track and its ground pad over 1.60 mm, adding about 0.62 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (a 10 uF bulk capacitor: its inductance matters only far above the band it serves). C201.1 (rail) runs 1.50 mm along its copper to its nearest via, 0.50 mm past the 1 mm beside the pad: 0.28 nH; C201.2 (ground) runs 1.60 mm along its copper to its nearest via, 0.60 mm past the 1 mm beside the pad: 0.34 nH. Each run past the pad as one conductor of a pair 2.16 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.62 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.29 nH (pad 0.15 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C4C4 on '3V3_1': its rail pad reaches its via over 2.07 mm of track, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C4 on '3V3_1': its rail pad reaches its via over 2.07 mm of track, adding about 0.54 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C4.1 (rail) runs 2.07 mm along its copper to its nearest via, 1.07 mm past the 1 mm beside the pad: 0.54 nH; C4.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.59 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.54 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 0.77 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.26 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C69C69 on '5V_2': its rail pad reaches its via over 2.14 mm of track, adding about 0.57 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C69 on '5V_2': its rail pad reaches its via over 2.14 mm of track, adding about 0.57 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C69.1 (rail) runs 2.14 mm along its copper to its nearest via, 1.14 mm past the 1 mm beside the pad: 0.57 nH; C69.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.58 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.57 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.00 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.65 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

    • C82C82 on '5V_1': its rail pad reaches its via over 2.20 mm of track, adding about 0.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value)

      C82 on '5V_1': its rail pad reaches its via over 2.20 mm of track, adding about 0.61 nH to its loop, past Probe's 0.5 nH starting value; put the vias at the pads (within a quarter of the starting value). C82.1 (rail) runs 2.20 mm along its copper to its nearest via, 1.20 mm past the 1 mm beside the pad: 0.61 nH; C82.2 (ground) not measured: the pad sits in a pour of its net on its own layer, which has no track length to measure. Each run past the pad as one conductor of a pair 1.59 mm apart (the pad pitch), 0.2 l ln(D/R) nH with R 0.127 mm (the track's width is not read): 0.61 nH in all. Put the vias at the pads (or in them), one per pad at least, the rail's and the ground's close together; the capacitor's own inductance as mounted is 1.08 nH (pad 0.10 nH + no via of the first net within 1 mm of its pad: the study's 0.6 nH per mm of 0.78 mm depth, ASSUMED). 0.5 nH is Probe's starting value, about the whole mounted inductance of a well-mounted 0402.

  17. ConnectorDomainMixedminorOpen

    J6 takes 2 different supplies off the board on one connector: Net-(C144-Pad1) (24 V), Net-(C143-Pad1) (7.5 V)

    J6 carries 2 different supplies out of the board on one connector: Net-(C144-Pad1) (24 V) on 3, Net-(C143-Pad1) (7.5 V) on 1. Declare the intent. Two rails on one connector is ordinary in a docking or power-distribution interface and a hazard in a signal one, and the difference is not visible from the netlist — but note that adjacent contacts at different voltages are exactly what a mirrored, reversed or off-by-one cable shorts together, so the cost of getting the mating wrong is a rail collision rather than a dead signal. If this is a standard connector, declare its family (connector_family_declare) and file the standard's contact map: supplies on the contacts it assigns to power are then not reported.

    At J6

  18. ReferencePlaneDiscontinuityminorOpen

    ReferencePlaneDiscontinuity: 53 boards×53

    Checked by the review, stands · Claude walker W1 (Cern session) — Checked: 87 split/void/reference-change sites read from the copper stand as reported; they are layout-practice findings with Probe's default limits, and no datasheet or app note on file sets one for these RF and control nets. Left for the owner.

    At split@L6_PSU:3V3_1|GND, void:3V3_1@L6_PSU:139.56,-126.83, void:3V3_1@L6_PSU:150.67,-184.52, void:3V3_1@L6_PSU:155.22,-180.95, void:3V3_1@L6_PSU:207.13,-117.15, void:3V3_1@L6_PSU:209.75,-110.26 and 47 more

    Each finding, with its own headline
    • split@L6_PSU:3V3_1|GND'/TOP/PLL/PLL_LOCKED' crosses the split between the 3V3_1 and GND planes on L6_PSU at 1 place, all with a plane on the track's other side (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      On L6_PSU the 3V3_1 and GND planes part, and '/TOP/PLL/PLL_LOCKED' crosses from one to the other at 1 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 1 of the 1 crossing(s) the track's other neighbour carries a plane, which the return can use there. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (134.38, -195.88), 6.98 mm; other side: GND on L8_BOTTOM, 0.13 mm from the track against 0.13 mm to L6_PSU: 50% of the return on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=split%40L6_PSU%3A3V3_1%7CGND serves each with its own layer_image region; all of them lie in x 133.38..135.99, y -199.94..-191.21 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:139.56,-126.83'/TOP/ADC//ADC_RST' crosses where the outline of the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.26 mm; 1 cleared on both sides of the track (fastest: /TOP/ADC//ADC_RST at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_RST' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.26 mm under the track with no copper, at (139.56, -126.72), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.87 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 2 reference layers: '/TOP/ADC//ADC_RST' on L7_DIGITAL at (139.56, -126.83), 1.04 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/ADC//ADC_RST' on L7_DIGITAL at (139.56, -126.72), 1.26 mm, running ALONG the bare copper for 0.87 mm, not across it over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A139.56%2C-126.83 serves each with its own layer_image region; all of them lie in x 138.56..140.56, y -129.15..-125.34 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:150.67,-184.52'/TOP/PLL/PLL_ENout' crosses where the outline of the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.7 mm; 1 cleared on both sides of the track (fastest: /TOP/PLL/PLL_ENout at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_ENout' on L7_DIGITAL, the 3V3_1 plane on L6_PSU has 1.7 mm under the track with no copper, at (150.67, -184.52), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 2 reference layers: '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (150.67, -184.52), 1.7 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (150.97, -184.22), 0.88 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A150.67%2C-184.52 serves each with its own layer_image region; all of them lie in x 149.07..152.28, y -186.12..-182.92 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:155.22,-180.95'/TOP/PLL/PLL_ENout' crosses where the outline of the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.55 mm; 1 cleared on both sides of the track (fastest: /TOP/PLL/PLL_ENout at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_ENout' on L7_DIGITAL, the 3V3_1 plane on L6_PSU has 1.55 mm under the track with no copper, at (155.22, -180.95), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 3 reference layers: '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (155.22, -180.95), 1.55 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (155.22, -180.62), 0.88 mm over no copper; other side: no plane on L6_PSU / '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (155.22, -181.53), 0.26 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A155.22%2C-180.95 serves each with its own layer_image region; all of them lie in x 154.22..156.22, y -182.73..-179.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:207.13,-117.15'Net-(R130-Pad1)' crosses where the outline of the 3V3_1 plane on L6_PSU is drawn back, at 1 place, the longest 1.36 mm (fastest: Net-(R130-Pad1) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R130-Pad1)' on L7_DIGITAL, the 3V3_1 plane on L6_PSU has 1.36 mm under the track with no copper, at (207.13, -117.15), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'Net-(R130-Pad1)' on L7_DIGITAL at (207.13, -117.15), 1.36 mm over no copper; other side: GND on L8_BOTTOM, 0.13 mm from the track against 0.13 mm to L6_PSU: 50% of the return on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A207.13%2C-117.15 serves each with its own layer_image region; all of them lie in x 205.45..208.81, y -118.15..-116.15 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:3V3_1@L6_PSU:209.75,-110.26'/TOP/ADC//ADC_CS' crosses where the outline of the 3V3_1 plane on L6_PSU and the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.07 mm; 1 cleared on both sides of the track (fastest: /TOP/ADC//ADC_CS at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_CS' on L7_DIGITAL, the 3V3_1 plane on L6_PSU has 1.07 mm under the track with no copper, at (209.75, -110.26), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 and of the pour at x 126.96..220.98, y -192.21..-76.84 is drawn back there. At 1 place(s) the track's plane is cleared on both sides of it, the same stretch on each reference layer: it has no plane on either side there, counted once. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • one stretch, cleared on 2 reference layers: '/TOP/ADC//ADC_CS' on L7_DIGITAL at (209.75, -110.26), 1.07 mm over no copper; other side: no plane on L8_BOTTOM / '/TOP/ADC//ADC_CS' on L7_DIGITAL at (209.75, -110.26), 1.07 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A3V3_1%40L6_PSU%3A209.75%2C-110.26 serves each with its own layer_image region; all of them lie in x 208.21..211.28, y -111.26..-109.26 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:5V_2@L4_PSU:173.08,-193.41'/TOP/ADC/MIXERout0' crosses where the outline of the 5V_2 plane on L4_PSU is drawn back, at 1 place, the longest 1.06 mm (fastest: /TOP/ADC/MIXERout0 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/MIXERout0' on L3_ANALOG, the 5V_2 plane on L4_PSU has 1.06 mm under the track with no copper, at (173.08, -193.41), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 126.96..238.86, y -206.64..-76.84 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/MIXERout0' on L3_ANALOG at (173.08, -193.41), 1.06 mm over no copper; other side: GND on L2_GND, 0.13 mm from the track against 0.13 mm to L4_PSU: 50% of the return on L4_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3A5V_2%40L4_PSU%3A173.08%2C-193.41 serves each with its own layer_image region; all of them lie in x 172.08..174.08, y -194.94..-191.88 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:218.25,-135.27'/TOP/digital_interface/PLL_CE-N' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.04 mm (fastest: /TOP/digital_interface/PLL_CE-N at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/digital_interface/PLL_CE-N' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.04 mm under the track with no copper, at (218.25, -135.27), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/digital_interface/PLL_CE-N' on L1_TOP-RO4350_B at (218.25, -135.27), 1.04 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A218.25%2C-135.27 serves each with its own layer_image region; all of them lie in x 216.86..219.6, y -136.62..-133.91 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L2_GND:230.47,-111.94'/TOP/digital_interface/ADC_MISO-N' crosses where the outline of the GND plane on L2_GND is drawn back, at 1 place, the longest 1.98 mm (fastest: /TOP/digital_interface/ADC_MISO-N at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/digital_interface/ADC_MISO-N' on L1_TOP-RO4350_B, the GND plane on L2_GND has 1.98 mm under the track with no copper, at (230.47, -111.94), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/digital_interface/ADC_MISO-N' on L1_TOP-RO4350_B at (230.47, -111.94), 1.98 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L2_GND%3A230.47%2C-111.94 serves each with its own layer_image region; all of them lie in x 228.64..232.24, y -113.4..-110.72 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:214.64,-133.42'/TOP/digital_interface/PLL_ENA' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 1.07 mm (fastest: /TOP/digital_interface/PLL_ENA at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/digital_interface/PLL_ENA' on L8_BOTTOM, the GND plane on L7_DIGITAL has 1.07 mm under the track with no copper, at (214.64, -133.42), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/digital_interface/PLL_ENA' on L8_BOTTOM at (214.64, -133.42), 1.07 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A214.64%2C-133.42 serves each with its own layer_image region; all of them lie in x 213.64..215.64, y -134.96..-131.89 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:218.4,-125.33'/TOP/digital_interface/SPARE2-N' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 1.06 mm (fastest: /TOP/digital_interface/SPARE2-N at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/digital_interface/SPARE2-N' on L8_BOTTOM, the GND plane on L7_DIGITAL has 1.06 mm under the track with no copper, at (218.4, -125.33), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/digital_interface/SPARE2-N' on L8_BOTTOM at (218.4, -125.33), 1.06 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A218.4%2C-125.33 serves each with its own layer_image region; all of them lie in x 216.87..219.93, y -126.33..-124.33 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L7_DIGITAL:229.81,-110.33'/TOP/digital_interface/D_ENA' crosses where the outline of the GND plane on L7_DIGITAL is drawn back, at 1 place, the longest 1.07 mm (fastest: /TOP/digital_interface/D_ENA at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/digital_interface/D_ENA' on L8_BOTTOM, the GND plane on L7_DIGITAL has 1.07 mm under the track with no copper, at (229.81, -110.33), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/digital_interface/D_ENA' on L8_BOTTOM at (229.81, -110.33), 1.07 mm over no copper; other side: none: the signal layer is outermost

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L7_DIGITAL%3A229.81%2C-110.33 serves each with its own layer_image region; all of them lie in x 228.27..231.34, y -111.33..-109.33 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:137.89,-132.7'/TOP/ADC//ADC_RST' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.95 mm (fastest: /TOP/ADC//ADC_RST at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_RST' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.95 mm under the track with no copper, at (137.89, -132.7), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.23 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC//ADC_RST' on L7_DIGITAL at (137.89, -132.7), 2.95 mm, running ALONG the bare copper for 1.23 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A137.89%2C-132.7 serves each with its own layer_image region; all of them lie in x 136.89..139.37, y -134.83..-130.08 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:138.01,-129.76'/TOP/ADC/ADC_MOSI' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.18 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.18 mm under the track with no copper, at (138.01, -129.76), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (138.01, -129.76), 1.18 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A138.01%2C-129.76 serves each with its own layer_image region; all of them lie in x 136.72..139.58, y -130.76..-128.76 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:150.12,-163.96'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.69 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.69 mm under the track with no copper, at (150.12, -163.96), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (150.12, -163.96), 1.69 mm over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A150.12%2C-163.96 serves each with its own layer_image region; all of them lie in x 148.7..151.73, y -166.35..-162.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:153.7,-162.24'/TOP/PLL/PLL_LE' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 4.63 mm (fastest: /TOP/PLL/PLL_LE at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LE' on L7_DIGITAL, the GND plane on L8_BOTTOM has 4.63 mm under the track with no copper, at (153.7, -162.24), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.78 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_LE' on L7_DIGITAL at (153.7, -162.24), 4.63 mm, running ALONG the bare copper for 1.78 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A153.7%2C-162.24 serves each with its own layer_image region; all of them lie in x 152.7..155.7, y -166.52..-159.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:157.68,-161'/TOP/PLL/PLL_CLK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.51 mm (fastest: /TOP/PLL/PLL_CLK at 1 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_CLK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.51 mm under the track with no copper, at (157.68, -161), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_CLK' on L7_DIGITAL at (157.68, -161), 0.51 mm over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A157.68%2C-161 serves each with its own layer_image region; all of them lie in x 156.68..158.68, y -162.26..-159.75 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:157.68,-162.74'/TOP/PLL/PLL_CLK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 3.56 mm (fastest: /TOP/PLL/PLL_CLK at 1 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_CLK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 3.56 mm under the track with no copper, at (157.68, -162.74), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_CLK' on L7_DIGITAL at (157.68, -162.74), 3.56 mm over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A157.68%2C-162.74 serves each with its own layer_image region; all of them lie in x 155.69..158.68, y -166.47..-160.77 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:159.65,-162.2'/TOP/PLL/PLL_DATA' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 4.52 mm (fastest: /TOP/PLL/PLL_DATA at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_DATA' on L7_DIGITAL, the GND plane on L8_BOTTOM has 4.52 mm under the track with no copper, at (159.65, -162.2), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.08 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_DATA' on L7_DIGITAL at (159.65, -162.2), 4.52 mm, running ALONG the bare copper for 2.08 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A159.65%2C-162.2 serves each with its own layer_image region; all of them lie in x 157.69..160.65, y -166.41..-159.74 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:171.7,-109.38'/TOP/ADC/ADC_SCK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.76 mm (fastest: /TOP/ADC/ADC_SCK at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_SCK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.76 mm under the track with no copper, at (171.7, -109.38), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.55 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (171.7, -109.38), 0.76 mm, running ALONG the bare copper for 0.55 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A171.7%2C-109.38 serves each with its own layer_image region; all of them lie in x 170.32..173.08, y -110.38..-108.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:171.7,-110.48'/TOP/ADC//ADC_RST' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.76 mm (fastest: /TOP/ADC//ADC_RST at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_RST' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.76 mm under the track with no copper, at (171.7, -110.48), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.56 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC//ADC_RST' on L7_DIGITAL at (171.7, -110.48), 0.76 mm, running ALONG the bare copper for 0.56 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A171.7%2C-110.48 serves each with its own layer_image region; all of them lie in x 170.32..173.08, y -111.48..-109.48 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:171.82,-109.01'/TOP/ADC/ADC_MOSI' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.52 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.52 mm under the track with no copper, at (171.82, -109.01), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.52 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (171.82, -109.01), 0.52 mm, running ALONG the bare copper for 0.52 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A171.82%2C-109.01 serves each with its own layer_image region; all of them lie in x 170.56..173.08, y -110.01..-108.01 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:173.63,-109.01'/TOP/ADC/ADC_MOSI' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.11 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.11 mm under the track with no copper, at (173.63, -109.01), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.46 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (173.63, -109.01), 2.11 mm, running ALONG the bare copper for 1.46 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A173.63%2C-109.01 serves each with its own layer_image region; all of them lie in x 171.58..175.69, y -110.01..-108.01 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:173.75,-109.38'/TOP/ADC/ADC_SCK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.34 mm (fastest: /TOP/ADC/ADC_SCK at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_SCK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.34 mm under the track with no copper, at (173.75, -109.38), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.16 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (173.75, -109.38), 2.34 mm, running ALONG the bare copper for 1.16 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A173.75%2C-109.38 serves each with its own layer_image region; all of them lie in x 171.58..175.92, y -110.38..-108.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:178.49,-121.54'/TOP/ADC/ADC_MISO' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.12 mm (fastest: /TOP/ADC/ADC_MISO at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MISO' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.12 mm under the track with no copper, at (178.49, -121.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_MISO' on L7_DIGITAL at (178.49, -121.54), 1.12 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A178.49%2C-121.54 serves each with its own layer_image region; all of them lie in x 176.93..180.05, y -122.54..-120.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:192.77,-121.54'/TOP/ADC/ADC_MISO' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.06 mm (fastest: /TOP/ADC/ADC_MISO at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MISO' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.06 mm under the track with no copper, at (192.77, -121.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_MISO' on L7_DIGITAL at (192.77, -121.54), 1.06 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A192.77%2C-121.54 serves each with its own layer_image region; all of them lie in x 191.24..194.3, y -122.54..-120.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:193.2,-109.38'/TOP/ADC/ADC_SCK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.75 mm (fastest: /TOP/ADC/ADC_SCK at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_SCK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.75 mm under the track with no copper, at (193.2, -109.38), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.75 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (193.2, -109.38), 0.75 mm, running ALONG the bare copper for 0.75 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A193.2%2C-109.38 serves each with its own layer_image region; all of them lie in x 191.82..194.57, y -110.38..-108.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:193.32,-109.01'/TOP/ADC/ADC_MOSI' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (193.32, -109.01), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.5 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (193.32, -109.01), 0.5 mm, running ALONG the bare copper for 0.5 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A193.32%2C-109.01 serves each with its own layer_image region; all of them lie in x 192.07..194.57, y -110.01..-108.01 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:193.33,-110.65'/TOP/ADC//ADC_RST' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.69 mm (fastest: /TOP/ADC//ADC_RST at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_RST' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.69 mm under the track with no copper, at (193.33, -110.65), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC//ADC_RST' on L7_DIGITAL at (193.33, -110.65), 0.69 mm over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A193.33%2C-110.65 serves each with its own layer_image region; all of them lie in x 191.99..194.52, y -111.84..-109.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:195.13,-109.01'/TOP/ADC/ADC_MOSI' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.09 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.09 mm under the track with no copper, at (195.13, -109.01), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.24 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (195.13, -109.01), 2.09 mm, running ALONG the bare copper for 1.24 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A195.13%2C-109.01 serves each with its own layer_image region; all of them lie in x 193.08..197.17, y -110.01..-108.01 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:195.25,-109.38'/TOP/ADC/ADC_SCK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.34 mm (fastest: /TOP/ADC/ADC_SCK at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_SCK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.34 mm under the track with no copper, at (195.25, -109.38), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.35 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (195.25, -109.38), 2.34 mm, running ALONG the bare copper for 1.35 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A195.25%2C-109.38 serves each with its own layer_image region; all of them lie in x 193.08..197.42, y -110.38..-108.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:201.39,-109.38'/TOP/ADC/ADC_SCK' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.49 mm (fastest: /TOP/ADC/ADC_SCK at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_SCK' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.49 mm under the track with no copper, at (201.39, -109.38), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.65 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_SCK' on L7_DIGITAL at (201.39, -109.38), 2.49 mm, running ALONG the bare copper for 1.65 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A201.39%2C-109.38 serves each with its own layer_image region; all of them lie in x 199.14..203.63, y -110.38..-108.38 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:206.17,-118.45'/TOP/ADC/ADC_ALARM' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 3.79 mm (fastest: /TOP/ADC/ADC_ALARM at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/ADC/ADC_ALARM' on L7_DIGITAL, the GND plane on L8_BOTTOM has 3.79 mm under the track with no copper, at (206.17, -118.45), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.94 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_ALARM' on L7_DIGITAL at (206.17, -118.45), 3.79 mm, running ALONG the bare copper for 2.94 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A206.17%2C-118.45 serves each with its own layer_image region; all of them lie in x 203.28..209.07, y -119.45..-117.45 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:207.63,-110.26'/TOP/ADC//ADC_CS' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.03 mm (fastest: /TOP/ADC//ADC_CS at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_CS' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.03 mm under the track with no copper, at (207.63, -110.26), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.61 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC//ADC_CS' on L7_DIGITAL at (207.63, -110.26), 1.03 mm, running ALONG the bare copper for 0.61 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A207.63%2C-110.26 serves each with its own layer_image region; all of them lie in x 206.11..209.14, y -111.26..-109.26 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:212.78,-135.62'/TOP/PLL/PLL_ENout' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.69 mm (fastest: /TOP/PLL/PLL_ENout at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_ENout' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.69 mm under the track with no copper, at (212.78, -135.62), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (212.78, -135.62), 0.69 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A212.78%2C-135.62 serves each with its own layer_image region; all of them lie in x 211.43..214.13, y -136.62..-134.62 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:218.25,-122.18'/TOP/PLL/PLL_LOCKED' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 10.66 mm (fastest: /TOP/PLL/PLL_LOCKED at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL, the GND plane on L8_BOTTOM has 10.66 mm under the track with no copper, at (218.25, -122.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 9.39 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_LOCKED' on L7_DIGITAL at (218.25, -122.18), 10.66 mm, running ALONG the bare copper for 9.39 mm, not across it over no copper; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A218.25%2C-122.18 serves each with its own layer_image region; all of them lie in x 211.92..224.58, y -123.18..-121.18 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:224.33,-121.54'/TOP/ADC/ADC_MISO' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/ADC/ADC_MISO at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MISO' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (224.33, -121.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_MISO' on L7_DIGITAL at (224.33, -121.54), 0.5 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A224.33%2C-121.54 serves each with its own layer_image region; all of them lie in x 223.08..225.59, y -122.54..-120.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:225.27,-121.54'/TOP/ADC/ADC_MISO' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.5 mm (fastest: /TOP/ADC/ADC_MISO at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MISO' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.5 mm under the track with no copper, at (225.27, -121.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.

      • '/TOP/ADC/ADC_MISO' on L7_DIGITAL at (225.27, -121.54), 0.5 mm over no copper; other side: no plane on L6_PSU

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A225.27%2C-121.54 serves each with its own layer_image region; all of them lie in x 224.02..226.52, y -122.54..-120.54 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:225.28,-187.75'/TOP/Frequency_dividers/FD2_S0' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.34 mm (fastest: /TOP/Frequency_dividers/FD2_S0 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_S0' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.34 mm under the track with no copper, at (225.28, -187.75), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD2_S0' on L7_DIGITAL at (225.28, -187.75), 0.34 mm over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A225.28%2C-187.75 serves each with its own layer_image region; all of them lie in x 224.16..226.4, y -188.87..-186.63 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:226.72,-186.31'/TOP/Frequency_dividers/FD2_S0' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.96 mm (fastest: /TOP/Frequency_dividers/FD2_S0 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_S0' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.96 mm under the track with copper of GND, not a plane, at (226.72, -186.31), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD2_S0' on L7_DIGITAL at (226.72, -186.31), 1.96 mm over copper of GND, not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A226.72%2C-186.31 serves each with its own layer_image region; all of them lie in x 224.9..228.48, y -188.13..-184.55 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:233.41,-169.06'/TOP/Frequency_dividers/FD1_N1' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 1.27 mm (fastest: /TOP/Frequency_dividers/FD1_N1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 1.27 mm under the track with no copper, at (233.41, -169.06), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.28 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL at (233.41, -169.06), 1.27 mm, running ALONG the bare copper for 1.28 mm, not across it over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A233.41%2C-169.06 serves each with its own layer_image region; all of them lie in x 231.77..235.05, y -170.06..-168.06 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:234.05,-170.63'/TOP/Frequency_dividers/FD1_N0' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 3.93 mm (fastest: /TOP/Frequency_dividers/FD1_N0 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_N0' on L7_DIGITAL, the GND plane on L8_BOTTOM has 3.93 mm under the track with no copper, at (234.05, -170.63), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.95 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD1_N0' on L7_DIGITAL at (234.05, -170.63), 3.93 mm, running ALONG the bare copper for 2.95 mm, not across it over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A234.05%2C-170.63 serves each with its own layer_image region; all of them lie in x 231.43..237.16, y -171.63..-169.13 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:234.55,-169.06'/TOP/Frequency_dividers/FD1_N1' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.37 mm (fastest: /TOP/Frequency_dividers/FD1_N1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.37 mm under the track with no copper, at (234.55, -169.06), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD1_N1' on L7_DIGITAL at (234.55, -169.06), 0.37 mm over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A234.55%2C-169.06 serves each with its own layer_image region; all of them lie in x 233.37..235.74, y -170.06..-168.06 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:242.68,-109.16'Net-(U35-Pad8)' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 3.43 mm (fastest: Net-(U35-Pad8) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(U35-Pad8)' on L7_DIGITAL, the GND plane on L8_BOTTOM has 3.43 mm under the track with copper of GND, not a plane, at (242.68, -109.16), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.56 mm). No hole cleared it: the outline of the pour at x 243.31..244.81, y -109.84..-107.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'Net-(U35-Pad8)' on L7_DIGITAL at (242.68, -109.16), 3.43 mm, running ALONG the bare copper for 2.56 mm, not across it over copper of GND, not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A242.68%2C-109.16 serves each with its own layer_image region; all of them lie in x 239.52..244.74, y -110.16..-106.97 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:247.76,-131.74'/TOP/Frequency_dividers/FD2_DIV1' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.71 mm (fastest: /TOP/Frequency_dividers/FD2_DIV1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.71 mm under the track with no copper, at (247.76, -131.74), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 241.04..251.1, y -134.71..-129.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (247.76, -131.74), 0.71 mm over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A247.76%2C-131.74 serves each with its own layer_image region; all of them lie in x 246.47..248.99, y -132.97..-130.51 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:248.48,-129.91'/TOP/Frequency_dividers/FD2_BYP' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 2.59 mm (fastest: /TOP/Frequency_dividers/FD2_BYP at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_BYP' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.59 mm under the track with copper of GND, not a plane, at (248.48, -129.91), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.27 mm). No hole cleared it: the outline of the pour at x 241.04..251.1, y -134.71..-129.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD2_BYP' on L7_DIGITAL at (248.48, -129.91), 2.59 mm, running ALONG the bare copper for 2.27 mm, not across it over copper of GND, not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A248.48%2C-129.91 serves each with its own layer_image region; all of them lie in x 245.94..250.8, y -130.91..-128.91 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:249.52,-132.06'/TOP/Frequency_dividers/FD2_DIV1' crosses where the outline of the GND plane on L8_BOTTOM is drawn back, at 1 place, the longest 0.48 mm (fastest: /TOP/Frequency_dividers/FD2_DIV1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 0.48 mm under the track with no copper, at (249.52, -132.06), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x 241.04..251.1, y -134.71..-129.88 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD2_DIV1' on L7_DIGITAL at (249.52, -132.06), 0.48 mm over no copper; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3A249.52%2C-132.06 serves each with its own layer_image region; all of them lie in x 248.28..250.76, y -133.06..-131.06 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of 15V'/TOP/ADC//ADC_RST' crosses where the GND plane on L8_BOTTOM is drawn back round copper of 15V, at 1 place, the longest 2.36 mm (fastest: /TOP/ADC//ADC_RST at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC//ADC_RST' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.36 mm under the track with copper of 15V, GND, not a plane, at (195.41, -109.85), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.4 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC//ADC_RST' on L7_DIGITAL at (195.41, -109.85), 2.36 mm, running ALONG the bare copper for 1.4 mm, not across it over copper of 15V, GND, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%2015V serves each with its own layer_image region; all of them lie in x 193.08..197.42, y -110.89..-108.85 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of 3V3_1'/TOP/PLL/PLL_ENout' crosses where the GND plane on L8_BOTTOM is drawn back round copper of 3V3_1, at 1 place, the longest 2.11 mm (fastest: /TOP/PLL/PLL_ENout at 20 ns 10-90 %, suggested by its name)

      Along '/TOP/PLL/PLL_ENout' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.11 mm under the track with copper of 3V3_1, not a plane, at (153.26, -182.68), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.58 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/PLL/PLL_ENout' on L7_DIGITAL at (153.26, -182.68), 2.11 mm, running ALONG the bare copper for 1.58 mm, not across it over copper of 3V3_1, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%203V3_1 serves each with its own layer_image region; all of them lie in x 151.26..155.27, y -183.93..-181.68 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of 5V_1'/TOP/Frequency_dividers/FD0_DIV1' crosses where the GND plane on L8_BOTTOM is drawn back round copper of 5V_1, at 1 place, the longest 6.06 mm (fastest: /TOP/Frequency_dividers/FD0_DIV1 at 100 ps 10-90 %, ASSUMED)

      Along '/TOP/Frequency_dividers/FD0_DIV1' on L7_DIGITAL, the GND plane on L8_BOTTOM has 6.06 mm under the track with copper of 5V_1, not a plane, at (210.99, -174.92), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 4.56 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/Frequency_dividers/FD0_DIV1' on L7_DIGITAL at (210.99, -174.92), 6.06 mm, running ALONG the bare copper for 4.56 mm, not across it over copper of 5V_1, not a plane; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%205V_1 serves each with its own layer_image region; all of them lie in x 208.93..216.37, y -175.92..-173.19 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of 5V_2'/TOP/ADC/ADC_MOSI' crosses where the GND plane on L8_BOTTOM is drawn back round copper of 5V_2, at 1 place, the longest 2.89 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.89 mm under the track with copper of 5V_2, not a plane, at (202.33, -109.01), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.91 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (202.33, -109.01), 2.89 mm, running ALONG the bare copper for 1.91 mm, not across it over copper of 5V_2, not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%205V_2 serves each with its own layer_image region; all of them lie in x 199.13..204.02, y -110.01..-108.01 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of Net-(R126-Pad2)'/TOP/ADC/ADC_MOSI' crosses where the GND plane on L8_BOTTOM is drawn back round copper of Net-(R126-Pad2), at 1 place, the longest 2.73 mm (fastest: /TOP/ADC/ADC_MOSI at 2 ns 10-90 %, suggested by its name)

      Along '/TOP/ADC/ADC_MOSI' on L7_DIGITAL, the GND plane on L8_BOTTOM has 2.73 mm under the track with copper of Net-(R126-Pad2), not a plane, at (137.17, -135.6), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.88 mm). No hole cleared it: the outline of the pour at x 109.72..258.72, y -222.94..-63.94 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • '/TOP/ADC/ADC_MOSI' on L7_DIGITAL at (137.17, -135.6), 2.73 mm, running ALONG the bare copper for 0.88 mm, not across it over copper of Net-(R126-Pad2), not a plane; other side: 3V3_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%20Net-%28R126-Pad2%29 serves each with its own layer_image region; all of them lie in x 135.81..139.35, y -137.09..-133.4 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

    • void:GND@L8_BOTTOM:copper of Net-(R140-Pad2)'Net-(R138-Pad2)' crosses where the GND plane on L8_BOTTOM is drawn back round copper of Net-(R140-Pad2), at 1 place, the longest 5.89 mm (fastest: Net-(R138-Pad2) at 100 ps 10-90 %, ASSUMED)

      Along 'Net-(R138-Pad2)' on L7_DIGITAL, the GND plane on L8_BOTTOM has 5.89 mm under the track with copper of Net-(R140-Pad2), not a plane, at (245.61, -136.74), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 4.07 mm). No hole cleared it: the outline of the pour at x 242.04..245, y -144.97..-138.6 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. Every crossing has a plane on the track's other side at most twice as far away as the broken one, so at most 50% of the return meets the break and the rest follows the track on that plane (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The finding is the lower tier (info).

      • 'Net-(R138-Pad2)' on L7_DIGITAL at (245.61, -136.74), 5.89 mm, running ALONG the bare copper for 4.07 mm, not across it over copper of Net-(R140-Pad2), not a plane, to the end of the track; other side: 5V_1 on L6_PSU, 0.13 mm from the track against 0.13 mm to L8_BOTTOM: 50% of the return on L8_BOTTOM

      Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/62/reference-planes?group=void%3AGND%40L8_BOTTOM%3Acopper%20of%20Net-%28R140-Pad2%29 serves each with its own layer_image region; all of them lie in x 241.55..247.87, y -140.86..-134.48 mm (board frame, Y up).

      Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.

Main parts

Part numberMakerDescriptionWhere
1590QHammondBOX1
39-30-1061MolexJ6
ADS8694IDBT#PBFTexas InstrumentsU29
BSH103NXPQ1
GAT-5+Mini-CircuitsU23
HMC1097LP4EHittiteU16
LMX2541SQ2690E/NOPBTexas InstrumentsU1
LTC2758ACLX#PBFLinear TechnologyU4
LTC6241HVCS8#PBFLINEAR TECHNOLOGYU9
LTC6655BHMS8-4.096#PBFLinear TechnologyU30
OPA209AIDGKRTexas InstrumentsU28
QCN-34+Mini-CircuitsU24
QSH-040-01-F-D-DP-ASamtecJ5
SN75LVDS389DBTTIU38
LT1012ACS8#PBFLINEAR TECHNOLOGYU5, U6
LT1360CS8#PBFLINEAR TECHNOLOGYU10, U11
LT6600CS8-2.5Linear TechnologyU14, U15
LTC2054HVCS5#PBFLINEAR TECHNOLOGYU7, U8
LTC6655BHMS8-1.25#PBFLinear TechnologyU12, U13
PMA2-43LN+Mini-CircuitsU21, U22
SIM-73L+Mini-CircuitsU26, U27
TPS7A3301RGWTTexas InstrumentsU44, U45
GP2Y+Mini-CircuitsU17, U25, U3
HMC705LP4EHittiteU18, U19, U20
NFM41PC155B1H3LMurataL12, L13, L14
SN75LVDT388ADBTTIU31, U32, U34
132430AmphenolJ1, J2, J3, J4
SN74LV4T125PWRTIU33, U35, U36, U37
TPS7A4700RGWTTexas InstrumentsU39, U40, U41, U42, U43
BMI-S-204-FLaird TechnologiesJ10, J11, J12, J7, J8, J9
D_3mm1FIX1, FIX2, FIX3, FIX4, FIX5, FIX6, FIX7, FIX8
LG M67K-G1J2-24OsramD1, D2, D3, D4, D5, D6, D7, D8
TEST-22MulticompTP1, TP2, TP3, TP4, TP5, TP6 and 3 more
C0603C222J5GACTUKEMETC18
C0603C223K5RACTUKEMETC22
CRCW0603102KFKEAVishayR157
CRCW0603105KFKEAVishayR159
CRCW060318R0FKEAHPVishayR16
CRCW06031M24FKEAVishayR158
CRCW0603332KFKEAVishayR156

About this design

Design
TIMIQ RF — OHWR0061 R1
Designed in
KiCad EDA
Board
8 copper layers, 150 × 160 mm, 464 components, 415 nets
Licence
CERN-OHL-1.2
Source
https://gitlab.com/ohwr/project/timiq/timiq-hw at commit 2cd7bfd55267
Attribution
CERN Open Hardware Repository, project ohwr/project/timiq/timiq-hw (commit 2cd7bfd55267cfea6673e703eb4b873480e2dee8, 2025-04-10). Licence: CERN-OHL-1.2. Source: https://gitlab.com/ohwr/project/timiq/timiq-hw. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
Reviewed with
Probe by E# (E-Sharp AB)