WRS FL BACKPLANE
OHWR0043 · revision R1
WRS FL BACKPLANE (OHWR0043 R1) is an open-hardware circuit board from the CERN Open Hardware Repository, designed in Altium Designer: a 6-layer board of 208.7 × 439.1 mm with 698 components and 535 nets, published under CERN-OHL-1.2.
review 91% walked · 9 findings: 1 blocker · 4 major · 4 minor (97 items)
Open in the interactive viewerRead the full review

Design review
Probe recorded 9 findings: 1 blocker · 4 major · 4 minor (97 items) on this design. Each is shown here with its reasoning; the full review links every one to the pins, nets and datasheet pages it rests on.
- NetCopperSplitblockerOpen
CHASSIS_GND's copper is in 8 pieces: FIX24.0, R110.1 and R111.1 and 6 other piece(s) are not connected to the rest of the net
CHASSIS_GND's copper is in 8 pieces: FIX24.0, R110.1 and R111.1 and 6 other piece(s) are not connected to the rest of the net. Piece 1: C18.1, C19.1, CN1_U_WR_LINK_1.0, CN1_U_WR_LINK_2.0, CN1_U_WR_LINK_4.0, CN1_U_WR_LINK_6.0, CN1_U_WR_LINK_8.0, CN2.21 and 37 more pin(s), on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 61 drill(s), over (-207.78, 5.59) to (0.13, 417.27). Piece 2: FIX24.0, R110.1 and R111.1, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-56.67, 265.66) to (-30.71, 274.8). Piece 3: FIX21.0, R106.1 and R107.1, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-56.9, 336.68) to (-30.71, 345.82). Piece 4: FIX20.0, R108.1 and R109.1, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-56.59, 194.64) to (-30.71, 203.78). Piece 5: CN1_U_WR_LINK_7.0, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-43.13, 322.39) to (-30.61, 324.57). Piece 6: CN1_U_WR_LINK_9.0, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-43.13, 393.35) to (-30.61, 395.54). Piece 7: CN1_U_WR_LINK_3.0, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-43.13, 180.45) to (-30.61, 182.63). Piece 8: CN1_U_WR_LINK_5.0, on TOP_LAYER, MIDLAYER1, MIDLAYER2 and BOTTOM_LAYER, 1 drill(s), over (-43.13, 251.42) to (-30.61, 253.6). The export files every one of these pins under the net, so every connectivity check passes; the copper the fab builds leaves them apart. Usually a pour island that touches only one via of its own net, or a track ending short of its copper: join the piece to the net and export again.
At split:CHASSIS_GND
WRS FL BACKPLANE: 6.3 V tantalum C70 on +5V (79%) and C69 on +3V6 (57%)
C70 (330 uF 6.3 V tantalum) runs at 79% of its rating on +5V, and C69 at 57% on +3V6. If they are MnO2, both exceed the 50% manufacturers recommend.
Part Rail Voltage Applied / 6.3 V Source C70 +5V 5 V 79% netlist; schematic ('330uF 6.3V', + on +5V) C69 +3V6 3.6 V 57% netlist; schematic MnO2 tantalum limit (capacitor guide, citing KEMET T491 p.14, Vishay 40246/EIA-809, AVX TDS-PTNO-0024 1.2.2): about 50% of rated up to 85 C. A polymer tantalum rated 10 V or less is allowed 90% (KEMET T2076 p.32-33).
The BOM says only 'Polarized Capacitor Tantalum D', so the electrolyte is unknown; a 6.3 V polymer part would pass. Orientation is correct.
- DecapOrdermajorOpen
IC7 supply pin 11 on '+1V8_A': the smallest capacitor C65 sits 5.0 mm away, behind C66 at 2.7 mm
IC7 supply pin 11 on '+1V8_A': the smallest capacitor C65 sits 5.0 mm away, behind C66 at 2.7 mm. IC7.11: the smallest value, C65 (100 nF), is 5.0 mm from the pin and C66 (4.7 uF) 2.7 mm: the high-frequency part sits behind more inductance than the bulk part, which needs it least. Swap them, or bring the smallest value to the pin: it serves the fastest current and is the one the loop inductance defeats. Distances are pad centre to pin centre in the board plane. The 5 mm radius, the 10x value step and the 1 mm / 1.5x tie tolerance are Probe's starting values.
At IC7.11
- PartLifecyclemajorOpen
PartLifecycle: 4 part numbers×4
4 Obsolete · on 14 placements
At IC12, U1_U_WR_LINK_1, U3, U4
Each finding, with its own headline
IC12FDS6690AS on 2 placements (IC12, IC13): the distributor catalogue reports "Obsolete" for onsemi's FDS6690AS
FDS6690AS on 2 placements (IC12, IC13): the distributor catalogue reports "Obsolete" for onsemi's FDS6690AS — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/FDS6690AS/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2022-03-31, 1,690 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.
U1_U_WR_LINK_1PCA9554PW on 10 placements (U1_U_WR_LINK_1, U1_U_WR_LINK_2, U1_U_WR_LINK_3, U1_U_WR_LINK_4, U1_U_WR_LINK_5, U1_U_WR_LINK_6, U1_U_WR_LINK_7, U1_U_WR_LINK_8, …): the distributor catalogue reports "Obsolete" for Texas Instruments's PCA9554PW
PCA9554PW on 10 placements (U1_U_WR_LINK_1, U1_U_WR_LINK_2, U1_U_WR_LINK_3, U1_U_WR_LINK_4, U1_U_WR_LINK_5, U1_U_WR_LINK_6, U1_U_WR_LINK_7, U1_U_WR_LINK_8, …): the distributor catalogue reports "Obsolete" for Texas Instruments's PCA9554PW — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/PCA9554PW/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2022-03-16, 1,705 day(s) ago), so this is a substitution rather than a buy. The distributor reports 74,348 left. No approved alternate is recorded for this position.
U37A-25.000MAHE-T on U3: the distributor catalogue reports "Obsolete" for TXC CORPORATION's 7A-25.000MAHE-T
7A-25.000MAHE-T on U3: the distributor catalogue reports "Obsolete" for TXC CORPORATION's 7A-25.000MAHE-T — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/7A-25.000MAHE-T/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2021-09-30, 1,872 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.
U4AT93C56A-10SU-2.7 on U4: the distributor catalogue reports "Obsolete" for Microchip Technology's AT93C56A-10SU-2.7
AT93C56A-10SU-2.7 on U4: the distributor catalogue reports "Obsolete" for Microchip Technology's AT93C56A-10SU-2.7 — a sourcing/longevity risk to confirm against the MANUFACTURER before acting. This board's BOM names no manufacturer for it, so whether that is the fitted maker's product was not checked. A distributor delisting is not the same claim as the part being unavailable; check the vendor's own lifecycle/product-change notice for the status and any named successor. Re-read the source: GET /api/odb/parts/AT93C56A-10SU-2.7/providers (which provider said it, the maker and part number it matched, its own words, and when we asked). THE LAST BUY DATE HAS PASSED (2012-04-30, 5,312 day(s) ago), so this is a substitution rather than a buy. The distributor reports NONE left. No approved alternate is recorded for this position.
- ReferencePlaneDiscontinuitymajorOpen
ReferencePlaneDiscontinuity: 86 boards×86
e.g. “'USB_INDICATOR' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 0.3 mm (fastest: USB_INDICATOR at 500 ps 10-90 %, suggested by its name)” · 85 different statements
At along@BOTTOM_LAYER:+2V5|GND, along@BOTTOM_LAYER:+5V|GND, along@PWR:+5V|CHASSIS_GND, along@TOP_LAYER:+3V3_SFP_U_WR_LINK_1|CHASSIS_GND, along@TOP_LAYER:+3V3_SFP_U_WR_LINK_1|GND, along@TOP_LAYER:+3V3_SFP_U_WR_LINK_2|CHASSIS_GND and 80 more
Each finding, with its own headline
along@BOTTOM_LAYER:+2V5|GND3 nets run ALONG the split between the +2V5 and GND planes on BOTTOM_LAYER at 4 places, the longest 18.13 mm; the impedance rises from 26 ohm to 28 ohm there at worst, 2.8 % of each edge reflected (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On BOTTOM_LAYER the +2V5 and GND planes part, and 3 nets run down the slot between them at 4 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 26 ohm to 62 ohm; along the slot 28 ohm to 63 ohm, reflecting up to 2.8 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 67 ohm). At 1 place(s) the impedance cannot be said: the slot's two edges were not both read beside the track. At 3 of the 4 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'FPGA-GPIO36' on MIDLAYER2 at (-31.58, 104.55), 5.71 mm, running ALONG the split for 2.41 mm, not across it, impedance not said: the slot's two edges were not both read beside the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-30.8, 54.91), 9.16 mm, running ALONG the split for 8.07 mm, not across it, 26 ohm over solid plane, 28 ohm along it: 2.8 % of each edge reflected; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-30.8, 47.16), 5.82 mm, running ALONG the split for 5.1 mm, not across it, 26 ohm over solid plane, 28 ohm along it: 2.8 % of each edge reflected; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-25.25, 65.09), 22.41 mm, running ALONG the split for 18.13 mm, not across it, 62 ohm over solid plane, 63 ohm along it: 1 % of each edge reflected; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40BOTTOM_LAYER%3A%2B2V5%7CGND serves each with its own layer_image region; all of them lie in x -32.58..-24.25, y 42.89..106.82 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@BOTTOM_LAYER:+5V|GND5 nets run ALONG the split between the +5V and GND planes on BOTTOM_LAYER at 6 places, the longest 19.82 mm; the impedance rises from 62 ohm to 66 ohm there at worst, 2.9 % of each edge reflected (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On BOTTOM_LAYER the +5V and GND planes part, and 5 nets run down the slot between them at 6 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 26 ohm to 62 ohm; along the slot 26 ohm to 66 ohm, reflecting up to 2.9 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 67 ohm). At 1 place(s) the impedance cannot be said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on. At 5 of the 6 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'FPGA-GPIO36' on MIDLAYER2 at (-32.13, 50.83), 1.36 mm, running ALONG the split for 0.63 mm, not across it, impedance not said: no plane lies on the track's other side or past the split layer, so the field along the slot has nothing to end on; other side: no plane on PWR
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-35.1, 41.38), 12.02 mm, running ALONG the split for 3.23 mm, not across it, 62 ohm over solid plane, 66 ohm along it: 2.9 % of each edge reflected; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-34.77, 41.38), 12.02 mm, running ALONG the split for 3.23 mm, not across it, 62 ohm over solid plane, 64 ohm along it: 1.7 % of each edge reflected; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-31.32, 52.53), 7.08 mm, running ALONG the split for 5.54 mm, not across it, 62 ohm over solid plane, 64 ohm along it: 1.3 % of each edge reflected; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO39' on MIDLAYER2 at (-29.34, 45.39), 33.76 mm, running ALONG the split for 19.82 mm, not across it, 26 ohm over solid plane, 26 ohm along it: 0.7 % of each edge reflected; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.31, 57.25), 7.41 mm, running ALONG the split for 7.03 mm, not across it, 62 ohm over solid plane, 63 ohm along it: 0.6 % of each edge reflected; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40BOTTOM_LAYER%3A%2B5V%7CGND serves each with its own layer_image region; all of them lie in x -36.1..-26.77, y 31.46..66.43 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@PWR:+5V|CHASSIS_GND'FPGA-GPIO37' runs ALONG the split between the +5V and CHASSIS_GND planes on PWR at 1 place, the longest 35.24 mm; the impedance rises from 62 ohm to 73 ohm there at worst, 8 % of each edge reflected (fastest: FPGA-GPIO37 at 100 ps 10-90 %, ASSUMED)
On PWR the +5V and CHASSIS_GND planes part, and 'FPGA-GPIO37' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 62 ohm; along the slot 73 ohm, reflecting up to 8 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 74 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'FPGA-GPIO37' on MIDLAYER2 at (-87.9, -18.05), 35.93 mm, running ALONG the split for 35.24 mm, not across it, 62 ohm over solid plane, 73 ohm along it: 8 % of each edge reflected; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40PWR%3A%2B5V%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -106.77..-69.04, y -19.05..-16.81 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_1|CHASSIS_GND4 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_1 and CHASSIS_GND planes on TOP_LAYER at 4 places, the longest 7.04 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_1 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_1 and CHASSIS_GND planes part, and 4 nets run down the slot between them at 4 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_1' on MIDLAYER1 at (-26.71, 106.25), 8.45 mm, running ALONG the split for 7.04 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_1' on MIDLAYER1 at (-26.82, 106.58), 7.87 mm, running ALONG the split for 6.54 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_1' on MIDLAYER1 at (-26.9, 106.99), 7.36 mm, running ALONG the split for 5.86 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_1' on MIDLAYER1 at (-26.97, 107.34), 6.89 mm, running ALONG the split for 5.08 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_1%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -30.08..-22.27, y 105.25..110.51 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_1|GND9 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_1 and GND planes on TOP_LAYER at 14 places, the longest 7.31 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: MGTRX115_3_N at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_1 and GND planes part, and 9 nets run down the slot between them at 14 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 8 of the 14 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_1' on MIDLAYER1 at (-38.82, 118.86), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_1' on MIDLAYER1 at (-38.47, 100.7), 15.1 mm, running ALONG the split for 2.84 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 7.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_N' on MIDLAYER1 at (-48.35, 114.49), 2.03 mm, running ALONG the split for 1.89 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.5 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_1' on MIDLAYER1 at (-37.86, 111.18), 7.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_P' on MIDLAYER1 at (-48.55, 114.49), 2.67 mm, running ALONG the split for 1.97 mm, not across it, 74 ohm over solid plane, 85 ohm along it: 7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_1' on MIDLAYER1 at (-40.08, 112.68), 8.2 mm, running ALONG the split for 4.39 mm, not across it, 74 ohm over solid plane, 84 ohm along it: 6.2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_1' on MIDLAYER1 at (-37.49, 103.05), 16.64 mm, running ALONG the split for 3.68 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_N' on MIDLAYER1 at (-52.65, 105.66), 2.85 mm, running ALONG the split for 2.84 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 0.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_N' on MIDLAYER1 at (-50.76, 119.27), 0.88 mm, running ALONG the split for 0.81 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 0.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_1_N' on MIDLAYER1 at (-52.98, 98.52), 0.68 mm, running ALONG the split for 0.41 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 0.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_P' on MIDLAYER1 at (-53.24, 119.44), 0.47 mm, running ALONG the split for 0.39 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_3_N' on MIDLAYER1 at (-53.14, 121.93), 3.39 mm, running ALONG the split for 3.02 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- and 2 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_1%7CGND serves each with its own layer_image region; all of them lie in x -55.7..-29.56, y 96.34..124.78 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_2|CHASSIS_GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_2 and CHASSIS_GND planes on TOP_LAYER at 7 places, the longest 6.96 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_2 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_2 and CHASSIS_GND planes part, and 6 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 83 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_2' on MIDLAYER1 at (-26.8, 141.55), 8.52 mm, running ALONG the split for 6.96 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_2' on MIDLAYER1 at (-26.95, 141.83), 7.92 mm, running ALONG the split for 6.43 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_2' on MIDLAYER1 at (-26.99, 142.22), 7.36 mm, running ALONG the split for 6.03 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_2' on MIDLAYER1 at (-27.06, 142.6), 6.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_2' on MIDLAYER1 at (-31.48, 141.55), 6.37 mm, running ALONG the split for 5.56 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SC14' on MIDLAYER1 at (-25.05, 133.66), 6.13 mm, running ALONG the split for 4.11 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.5 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SD14' on MIDLAYER1 at (-25.26, 133.27), 7.1 mm, running ALONG the split for 4.54 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_2%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.64..-22.04, y 132.27..145.99 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_2|GND8 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_2 and GND planes on TOP_LAYER at 9 places, the longest 7.31 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: MGTRX115_2_P at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_2 and GND planes part, and 8 nets run down the slot between them at 9 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 3 of the 9 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_2' on MIDLAYER1 at (-38.82, 154.34), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_2' on MIDLAYER1 at (-38.47, 136.19), 15.01 mm, running ALONG the split for 3.07 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_3_N' on MIDLAYER1 at (-48.13, 134.96), 4.24 mm, running ALONG the split for 3.99 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.5 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_2' on MIDLAYER1 at (-37.86, 146.66), 7.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_3_P' on MIDLAYER1 at (-47.93, 134.96), 4.88 mm, running ALONG the split for 4.05 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.3 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_2_P' on MIDLAYER1 at (-48.76, 156.36), 2.19 mm, running ALONG the split for 1.39 mm, not across it, 74 ohm over solid plane, 84 ohm along it: 6.3 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_2' on MIDLAYER1 at (-43.12, 149.76), 9.31 mm, running ALONG the split for 4.93 mm, not across it, 74 ohm over solid plane, 80 ohm along it: 4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_2' on MIDLAYER1 at (-37.61, 138.54), 15.92 mm, running ALONG the split for 6.57 mm, not across it, 74 ohm over solid plane, 77 ohm along it: 2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_3_P' on MIDLAYER1 at (-49.66, 143.92), 3.61 mm, running ALONG the split for 3.61 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_2%7CGND serves each with its own layer_image region; all of them lie in x -50.66..-29.56, y 131.82..160.26 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_3|CHASSIS_GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_3 and CHASSIS_GND planes on TOP_LAYER at 7 places, the longest 6.89 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_3 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_3 and CHASSIS_GND planes part, and 6 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 86 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_3' on MIDLAYER1 at (-26.78, 177.06), 8.51 mm, running ALONG the split for 6.89 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_3' on MIDLAYER1 at (-26.89, 177.34), 7.99 mm, running ALONG the split for 6.6 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_3' on MIDLAYER1 at (-26.99, 177.67), 7.4 mm, running ALONG the split for 6.1 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_3' on MIDLAYER1 at (-27.06, 178.08), 6.77 mm, running ALONG the split for 5.62 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_3' on MIDLAYER1 at (-31.43, 177.06), 6.33 mm, running ALONG the split for 5.39 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SC12' on MIDLAYER1 at (-25.41, 169.34), 6.26 mm, running ALONG the split for 3.78 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 7.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SD12' on MIDLAYER1 at (-25.84, 168.96), 6.76 mm, running ALONG the split for 3.78 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_3%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.64..-22.04, y 167.46..181.48 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_3|GND8 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_3 and GND planes on TOP_LAYER at 9 places, the longest 7.38 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: MGTRX115_0_N at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_3 and GND planes part, and 8 nets run down the slot between them at 9 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 5 of the 9 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_3' on MIDLAYER1 at (-38.82, 189.82), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_3' on MIDLAYER1 at (-38.47, 171.67), 15.02 mm, running ALONG the split for 2.94 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_3' on MIDLAYER1 at (-37.86, 182.14), 7.83 mm, running ALONG the split for 5.65 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_1_N' on MIDLAYER1 at (-49.04, 177.67), 2.97 mm, running ALONG the split for 1.64 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_3' on MIDLAYER1 at (-43.12, 185.22), 9.29 mm, running ALONG the split for 5.09 mm, not across it, 74 ohm over solid plane, 80 ohm along it: 3.6 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_3' on MIDLAYER1 at (-37.77, 174.02), 16.87 mm, running ALONG the split for 7.38 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 1.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_0_N' on MIDLAYER1 at (-54.65, 191.58), 3.12 mm, running ALONG the split for 2.88 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_0_P' on MIDLAYER1 at (-53.41, 190.1), 0.26 mm, running ALONG the split for 0.21 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_0_N' on MIDLAYER1 at (-51.12, 192.33), 1.12 mm, running ALONG the split for 1 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_3%7CGND serves each with its own layer_image region; all of them lie in x -55.65..-29.56, y 167.31..195.74 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_4|CHASSIS_GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_4 and CHASSIS_GND planes on TOP_LAYER at 7 places, the longest 6.84 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_4 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_4 and CHASSIS_GND planes part, and 6 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 86 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_4' on MIDLAYER1 at (-26.8, 212.52), 8.54 mm, running ALONG the split for 6.84 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_4' on MIDLAYER1 at (-26.86, 212.88), 7.99 mm, running ALONG the split for 6.6 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_4' on MIDLAYER1 at (-26.98, 213.16), 7.43 mm, running ALONG the split for 6.13 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_4' on MIDLAYER1 at (-27.04, 213.54), 6.84 mm, running ALONG the split for 5.82 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_4' on MIDLAYER1 at (-31.51, 212.52), 6.38 mm, running ALONG the split for 5.7 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SC10' on MIDLAYER1 at (-25.31, 205.16), 5.91 mm, running ALONG the split for 4.54 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 7.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SD10' on MIDLAYER1 at (-25.44, 204.6), 6.95 mm, running ALONG the split for 4.8 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.5 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_4%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.61..-22.04, y 203.6..216.96 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_4|GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_4 and GND planes on TOP_LAYER at 6 places, the longest 7.48 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_4 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_4 and GND planes part, and 6 nets run down the slot between them at 6 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 3 of the 6 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_4' on MIDLAYER1 at (-38.82, 225.31), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_4' on MIDLAYER1 at (-38.47, 207.15), 15.04 mm, running ALONG the split for 2.89 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_4' on MIDLAYER1 at (-37.86, 217.63), 7.83 mm, running ALONG the split for 5.65 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_4' on MIDLAYER1 at (-43.12, 220.65), 9.25 mm, running ALONG the split for 5.09 mm, not across it, 74 ohm over solid plane, 78 ohm along it: 2.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_4' on MIDLAYER1 at (-37.55, 209.51), 16.77 mm, running ALONG the split for 7.48 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-25.94, 225.25), 4.52 mm, running ALONG the split for 4.18 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_4%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-22.79, y 202.79..231.23 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_5|CHASSIS_GND4 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_5 and CHASSIS_GND planes on TOP_LAYER at 5 places, the longest 6.86 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_5 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_5 and CHASSIS_GND planes part, and 4 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_5' on MIDLAYER1 at (-26.81, 247.98), 8.57 mm, running ALONG the split for 6.86 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_5' on MIDLAYER1 at (-26.87, 248.23), 8.12 mm, running ALONG the split for 6.63 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_5' on MIDLAYER1 at (-26.98, 248.56), 7.52 mm, running ALONG the split for 6.18 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_5' on MIDLAYER1 at (-27.08, 248.9), 6.93 mm, running ALONG the split for 5.67 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_5' on MIDLAYER1 at (-31.51, 247.98), 6.39 mm, running ALONG the split for 5.59 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_5%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.66..-22.19, y 242.59..252.44 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_5|GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_5 and GND planes on TOP_LAYER at 6 places, the longest 7.31 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_5 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_5 and GND planes part, and 6 nets run down the slot between them at 6 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 3 of the 6 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_5' on MIDLAYER1 at (-38.82, 260.79), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_5' on MIDLAYER1 at (-38.47, 242.64), 14.98 mm, running ALONG the split for 3.02 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_5' on MIDLAYER1 at (-37.86, 253.11), 7.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_5' on MIDLAYER1 at (-43.12, 256.16), 9.27 mm, running ALONG the split for 5.13 mm, not across it, 74 ohm over solid plane, 79 ohm along it: 3.2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_5' on MIDLAYER1 at (-37.51, 244.99), 15.87 mm, running ALONG the split for 6.67 mm, not across it, 74 ohm over solid plane, 77 ohm along it: 1.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PE9' on MIDLAYER1 at (-25.9, 260.78), 4.27 mm, running ALONG the split for 3.98 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.6 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_5%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-22.91, y 238.27..266.71 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_6|CHASSIS_GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_6 and CHASSIS_GND planes on TOP_LAYER at 7 places, the longest 6.76 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_6 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_6 and CHASSIS_GND planes part, and 6 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 81 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 1 of the 7 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_6' on MIDLAYER1 at (-26.78, 283.52), 8.52 mm, running ALONG the split for 6.76 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_6' on MIDLAYER1 at (-26.86, 283.77), 8.08 mm, running ALONG the split for 6.56 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_6' on MIDLAYER1 at (-26.95, 284.07), 7.55 mm, running ALONG the split for 6.18 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_6' on MIDLAYER1 at (-27.04, 284.38), 7.05 mm, running ALONG the split for 5.75 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_6' on MIDLAYER1 at (-31.47, 283.52), 6.36 mm, running ALONG the split for 5.67 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SC6' on MIDLAYER1 at (-24.94, 275.39), 6.21 mm, running ALONG the split for 3.91 mm, not across it, 74 ohm over solid plane, 85 ohm along it: 7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SD6' on MIDLAYER1 at (-25.2, 275.08), 7.15 mm, running ALONG the split for 4.32 mm, not across it, 74 ohm over solid plane, 81 ohm along it: 4.2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_6%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.61..-22.04, y 274.08..287.93 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_6|GND5 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_6 and GND planes on TOP_LAYER at 5 places, the longest 7.73 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_6 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_6 and GND planes part, and 5 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 77 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 2 of the 5 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_6' on MIDLAYER1 at (-38.82, 296.28), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_6' on MIDLAYER1 at (-38.47, 278.12), 15.01 mm, running ALONG the split for 2.97 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_6' on MIDLAYER1 at (-37.86, 288.6), 7.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_6' on MIDLAYER1 at (-43.12, 291.69), 9.32 mm, running ALONG the split for 4.93 mm, not across it, 74 ohm over solid plane, 80 ohm along it: 4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_6' on MIDLAYER1 at (-37.54, 280.49), 16.82 mm, running ALONG the split for 7.73 mm, not across it, 74 ohm over solid plane, 77 ohm along it: 1.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_6%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-29.56, y 273.76..302.19 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_7|CHASSIS_GND4 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_7 and CHASSIS_GND planes on TOP_LAYER at 5 places, the longest 6.9 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_7 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_7 and CHASSIS_GND planes part, and 4 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_7' on MIDLAYER1 at (-26.78, 319.01), 8.51 mm, running ALONG the split for 6.9 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_7' on MIDLAYER1 at (-26.89, 319.28), 7.99 mm, running ALONG the split for 6.6 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_7' on MIDLAYER1 at (-26.98, 319.56), 7.49 mm, running ALONG the split for 6.15 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_7' on MIDLAYER1 at (-27.09, 319.84), 6.95 mm, running ALONG the split for 5.62 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_7' on MIDLAYER1 at (-31.43, 319.01), 6.36 mm, running ALONG the split for 5.32 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_7%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.66..-22.27, y 313.55..323.41 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_7|GND5 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_7 and GND planes on TOP_LAYER at 5 places, the longest 7.58 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_7 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_7 and GND planes part, and 5 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 77 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 2 of the 5 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_7' on MIDLAYER1 at (-38.82, 331.76), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_7' on MIDLAYER1 at (-38.47, 313.6), 15.02 mm, running ALONG the split for 3.04 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_7' on MIDLAYER1 at (-37.86, 324.08), 7.83 mm, running ALONG the split for 5.66 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_7' on MIDLAYER1 at (-43.12, 327.13), 9.27 mm, running ALONG the split for 5.13 mm, not across it, 74 ohm over solid plane, 79 ohm along it: 3.2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_7' on MIDLAYER1 at (-37.5, 315.96), 16.77 mm, running ALONG the split for 7.58 mm, not across it, 74 ohm over solid plane, 77 ohm along it: 1.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_7%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-29.56, y 309.24..337.68 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_8|CHASSIS_GND4 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_8 and CHASSIS_GND planes on TOP_LAYER at 5 places, the longest 6.92 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_8 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_8 and CHASSIS_GND planes part, and 4 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_8' on MIDLAYER1 at (-26.8, 354.46), 8.55 mm, running ALONG the split for 6.92 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_8' on MIDLAYER1 at (-26.89, 354.71), 8.06 mm, running ALONG the split for 6.51 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_8' on MIDLAYER1 at (-26.96, 355.04), 7.52 mm, running ALONG the split for 6.18 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_8' on MIDLAYER1 at (-26.96, 355.4), 7.05 mm, running ALONG the split for 5.98 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_8' on MIDLAYER1 at (-31.45, 354.46), 6.32 mm, running ALONG the split for 5.49 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_8%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.64..-22.22, y 349.04..358.89 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_8|GND5 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_8 and GND planes on TOP_LAYER at 5 places, the longest 7.68 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_8 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_8 and GND planes part, and 5 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 77 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 2 of the 5 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_8' on MIDLAYER1 at (-38.82, 367.24), 14.8 mm, running ALONG the split for 7.31 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_8' on MIDLAYER1 at (-38.47, 349.09), 15 mm, running ALONG the split for 2.99 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_8' on MIDLAYER1 at (-37.86, 359.56), 7.83 mm, running ALONG the split for 5.65 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_8' on MIDLAYER1 at (-43.12, 362.59), 9.25 mm, running ALONG the split for 5.09 mm, not across it, 74 ohm over solid plane, 78 ohm along it: 2.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_8' on MIDLAYER1 at (-37.5, 351.45), 16.87 mm, running ALONG the split for 7.68 mm, not across it, 74 ohm over solid plane, 77 ohm along it: 1.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_8%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-29.56, y 344.72..373.16 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_9|CHASSIS_GND6 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_9 and CHASSIS_GND planes on TOP_LAYER at 7 places, the longest 6.82 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_LINK_U_WR_LINK_9 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_9 and CHASSIS_GND planes part, and 6 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 86 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'SFP0_TX_DISABLE_U_WR_LINK_9' on MIDLAYER1 at (-26.81, 389.92), 8.55 mm, running ALONG the split for 6.82 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_9' on MIDLAYER1 at (-26.92, 390.17), 8.01 mm, running ALONG the split for 6.45 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_9' on MIDLAYER1 at (-27.03, 390.47), 7.46 mm, running ALONG the split for 6.05 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_LINK_U_WR_LINK_9' on MIDLAYER1 at (-27.09, 390.83), 6.89 mm, running ALONG the split for 5.67 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SFP0_TX_DISABLE_U_WR_LINK_9' on MIDLAYER1 at (-31.47, 389.92), 6.33 mm, running ALONG the split for 5.57 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SC0' on MIDLAYER1 at (-25.51, 382.37), 6.24 mm, running ALONG the split for 3.73 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 7.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'I2C_DL_SD0' on MIDLAYER1 at (-25.83, 381.89), 6.84 mm, running ALONG the split for 3.76 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.2 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_9%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -33.64..-22.04, y 380.36..394.38 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3_SFP_U_WR_LINK_9|GND5 nets run ALONG the split between the +3V3_SFP_U_WR_LINK_9 and GND planes on TOP_LAYER at 5 places, the longest 7.95 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 8.1 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_9 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3_SFP_U_WR_LINK_9 and GND planes part, and 5 nets run down the slot between them at 5 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 76 ohm to 87 ohm, reflecting up to 8.1 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 2 of the 5 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'WR_LINK1_LED_LINK_U_WR_LINK_9' on MIDLAYER1 at (-38.82, 402.73), 14.8 mm, running ALONG the split for 7.41 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8.1 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_9' on MIDLAYER1 at (-38.47, 384.57), 14.98 mm, running ALONG the split for 3.02 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_SYNCED_U_WR_LINK_9' on MIDLAYER1 at (-37.86, 395.05), 7.83 mm, running ALONG the split for 5.65 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_9' on MIDLAYER1 at (-43.12, 398.12), 9.29 mm, running ALONG the split for 5.09 mm, not across it, 74 ohm over solid plane, 80 ohm along it: 3.6 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_9' on MIDLAYER1 at (-37.83, 386.5), 16.7 mm, running ALONG the split for 7.95 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 1.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3_SFP_U_WR_LINK_9%7CGND serves each with its own layer_image region; all of them lie in x -45.64..-29.56, y 380.21..408.65 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:+3V3|GND18 nets run ALONG the split between the +3V3 and GND planes on TOP_LAYER at 22 places, the longest 6.34 mm; the impedance rises from 74 ohm to 87 ohm there at worst, 7.7 % of each edge reflected (fastest: LINK_ACT at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3 and GND planes part, and 18 nets run down the slot between them at 22 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 74 ohm to 87 ohm, reflecting up to 7.7 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 16 of the 22 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'FPGA_GPIO32' on MIDLAYER1 at (-30.53, 61.59), 2.5 mm, running ALONG the split for 2.5 mm, not across it, 74 ohm over solid plane, 87 ohm along it: 7.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO29' on MIDLAYER1 at (-30.05, 61.59), 2.5 mm, running ALONG the split for 2.5 mm, not across it, 74 ohm over solid plane, 86 ohm along it: 7.3 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO33' on MIDLAYER1 at (-30.94, 61.59), 2.5 mm, running ALONG the split for 2.5 mm, not across it, 74 ohm over solid plane, 85 ohm along it: 6.9 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO22' on MIDLAYER1 at (-26.37, 55.53), 2.46 mm, running ALONG the split for 1.02 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PE1' on MIDLAYER1 at (-22.56, 66.53), 2.43 mm, running ALONG the split for 2.43 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB3' on MIDLAYER1 at (-46.18, 62.9), 1.31 mm, running ALONG the split for 1.31 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO3' on MIDLAYER1 at (-22.12, 67.6), 1.38 mm, running ALONG the split for 1.38 mm, not across it, 74 ohm over solid plane, 82 ohm along it: 4.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_1_N' on MIDLAYER1 at (-51.2, 78.95), 0.24 mm, running ALONG the split for 0.24 mm, not across it, 74 ohm over solid plane, 81 ohm along it: 4.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD13' on MIDLAYER1 at (-44.37, 26.79), 2.51 mm, running ALONG the split for 1.5 mm, not across it, 74 ohm over solid plane, 80 ohm along it: 3.6 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-29.27, 46.37), 6.65 mm, running ALONG the split for 2.49 mm, not across it, 74 ohm over solid plane, 79 ohm along it: 3.3 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO32' on MIDLAYER1 at (-31.09, 49.63), 0.47 mm, running ALONG the split for 0.26 mm, not across it, 74 ohm over solid plane, 78 ohm along it: 2.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-29.26, 57.84), 5.12 mm, running ALONG the split for 3.78 mm, not across it, 74 ohm over solid plane, 76 ohm along it: 1.4 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- and 10 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3A%2B3V3%7CGND serves each with its own layer_image region; all of them lie in x -53.85..-21.12, y 24.65..79.95 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:CHASSIS_GND|GND7 nets run ALONG the split between the CHASSIS_GND and GND planes on TOP_LAYER at 7 places, the longest 1.73 mm; the impedance rises from 74 ohm to 75 ohm there at worst, 0.8 % of each edge reflected (fastest: WR_LINK0_LED_SYNCED_U_WR_LINK_6 at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the CHASSIS_GND and GND planes part, and 7 nets run down the slot between them at 7 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm, reflecting up to 0.8 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 1 place(s) the impedance cannot be said: the track's centreline is not over the slot. At 6 of the 7 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'FPGA_GPIO35' on MIDLAYER1 at (-35.43, 75.02), 2.36 mm, running ALONG the split for 1.73 mm, not across it, impedance not said: the track's centreline is not over the slot; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_7' on MIDLAYER1 at (-24.68, 324.69), 1.33 mm, running ALONG the split for 1.04 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-28.17, 74.77), 1.46 mm, running ALONG the split for 1.35 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_6' on MIDLAYER1 at (-24.88, 289.15), 1.13 mm, running ALONG the split for 0.84 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.8 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_8' on MIDLAYER1 at (-24.69, 360.1), 1.16 mm, running ALONG the split for 0.86 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO33' on MIDLAYER1 at (-28.22, 88.79), 1.75 mm, running ALONG the split for 1.7 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'WR_LINK0_LED_SYNCED_U_WR_LINK_9' on MIDLAYER1 at (-24.59, 395.55), 1.36 mm, running ALONG the split for 1.07 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.7 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3ACHASSIS_GND%7CGND serves each with its own layer_image region; all of them lie in x -36.79..-23.04, y 73.09..396.74 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:GND|NetIC6_U_WR_LINK_1_72 nets run ALONG the split between the GND and NetIC6_U_WR_LINK_1_7 planes on TOP_LAYER at 2 places, the longest 1 mm; the impedance rises from 74 ohm to 83 ohm there at worst, 5.5 % of each edge reflected (fastest: MGTRX116_0_N at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the GND and NetIC6_U_WR_LINK_1_7 planes part, and 2 nets run down the slot between them at 2 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. Over solid plane each track is 74 ohm; along the slot 75 ohm to 83 ohm, reflecting up to 5.5 % of each edge (a method-of-moments field solve of the cross-section, one dielectric; were the slot's edges to carry none of the return, up to 87 ohm). At 1 of the 2 place(s) the rise is within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none); the rest exceed it or cannot be said, so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'MGTRX116_0_P' on MIDLAYER1 at (-53.75, 107.15), 2.34 mm, running ALONG the split for 0.93 mm, not across it, 74 ohm over solid plane, 83 ohm along it: 5.5 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_0_N' on MIDLAYER1 at (-54.24, 107.8), 2.12 mm, running ALONG the split for 1 mm, not across it, 74 ohm over solid plane, 75 ohm along it: 0.3 % of each edge reflected; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3AGND%7CNetIC6_U_WR_LINK_1_7 serves each with its own layer_image region; all of them lie in x -55.74..-52.75, y 105.51..109.59 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
along@TOP_LAYER:GND|VCCR_LINK0_U_WR_LINK_3'MGTRX115_1_P' runs ALONG the split between the GND and VCCR_LINK0_U_WR_LINK_3 planes on TOP_LAYER at 1 place, the longest 0.15 mm; the impedance there is not said (fastest: MGTRX115_1_P at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the GND and VCCR_LINK0_U_WR_LINK_3 planes part, and 'MGTRX115_1_P' runs down the slot between them at 1 place(s), rather than across it. This is not a crossing: the return still follows the track, in the plane on its other side and in the slot's edges, so it does not detour. What changes is the track's own impedance. With the plane gone from under it on this side for that length, its field reaches further, to the slot's edges and to the next plane beyond, so its capacitance falls and its impedance rises; every edge travelling down it is partly reflected where it enters the stretch and again where it leaves, by (Z2 - Z1)/(Z2 + Z1). The longer the stretch against the edge's rise, the more of the edge sees the full step. A crossing is generally the worse fault; a mismatch is not free. At 1 place(s) the impedance cannot be said: the slot's two edges were not both read beside the track. No place stays within 10 %, the tolerance controlled impedance is commonly built to (the stackup states none), so the finding is a warning. One decision covers the split line's slot: whether these tracks may run down it, or should be moved over solid plane.
- 'MGTRX115_1_P' on MIDLAYER1 at (-49.41, 175), 0.36 mm, running ALONG the split for 0.15 mm, not across it, impedance not said: the slot's two edges were not both read beside the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=along%40TOP_LAYER%3AGND%7CVCCR_LINK0_U_WR_LINK_3 serves each with its own layer_image region; all of them lie in x -50.45..-48.12, y 173.99..176.11 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+3V3_SFP_U_WR_LINK_3|FPGA-GPIO383 nets change reference between +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 at 3 vias, none with a reference that continues across (fastest: I2C_DL_SC12 at 10 ns 10-90 %, suggested by its name)
At 3 via(s), on 3 net(s), the signal leaves a layer referenced by one of +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 3 with none. 3 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'I2C_DL_SD12' at (-32.16, 173.43), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_3 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SC12' at (-32.16, 174.24), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_3 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE12' at (-32.16, 175.03), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_3 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 5.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_3 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B3V3_SFP_U_WR_LINK_3%7CFPGA-GPIO38 serves each with its own layer_image region; all of them lie in x -34.16..-30.16, y 171.43..177.03 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+3V3_SFP_U_WR_LINK_4|FPGA-GPIO383 nets change reference between +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 at 3 vias, none with a reference that continues across (fastest: I2C_DL_SC11 at 10 ns 10-90 %, suggested by its name)
At 3 via(s), on 3 net(s), the signal leaves a layer referenced by one of +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 3 with none. 3 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'I2C_DL_SC11' at (-32.16, 223.98), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SD11' at (-32.16, 223.16), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE11' at (-32.16, 224.76), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 5.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_4 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B3V3_SFP_U_WR_LINK_4%7CFPGA-GPIO38 serves each with its own layer_image region; all of them lie in x -34.16..-30.16, y 221.16..226.76 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+3V3_SFP_U_WR_LINK_5|FPGA-GPIO383 nets change reference between +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 at 3 vias, none with a reference that continues across (fastest: I2C_DL_SC8 at 10 ns 10-90 %, suggested by its name)
At 3 via(s), on 3 net(s), the signal leaves a layer referenced by one of +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 3 with none. 3 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'I2C_DL_SD8' at (-32.16, 244.4), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_5 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SC8' at (-32.16, 245.21), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_5 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE8' at (-32.16, 246), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_5 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 5.4 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V3_SFP_U_WR_LINK_5 and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B3V3_SFP_U_WR_LINK_5%7CFPGA-GPIO38 serves each with its own layer_image region; all of them lie in x -34.16..-30.16, y 242.4..248 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+3V6|CHASSIS_GND22 nets change reference between +3V6 and CHASSIS_GND at 31 vias, none with a reference that continues across (fastest: FPGA_GPIO13 at 2 ns 10-90 %, suggested by its name)
At 31 via(s), on 22 net(s), the signal leaves a layer referenced by one of +3V6 and CHASSIS_GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 31 with none. 31 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V6 and CHASSIS_GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'ARM_2V5_GPIO_PE10' at (-19.89, 210.52), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 216.1 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO26' at (-19.89, 191.14), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 195.4 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO13' at (-10.77, 90.68), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 194.7 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE13' at (-19.89, 189.81), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 194.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO27' at (-19.91, 190.5), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 192.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO18' at (-19.79, 262.03), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 185.7 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO18' at (-10.8, 91.39), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 185.7 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO19' at (-19.76, 261.44), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 180.4 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO19' at (-10.8, 92.28), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 180.4 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE9' at (-19.76, 260.78), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 179.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE9' at (-10.82, 92.81), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 179.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE12' at (-19.76, 175.03), MIDLAYER1 -> MIDLAYER2: CHASSIS_GND on TOP_LAYER, GND on GND to +3V6 on PWR; pure, no reference continues across; stitching none, 177.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and CHASSIS_GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 19 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B3V6%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -21.91..-8.77, y 88.68..264.03 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+3V6|GND67 nets change reference between +3V6 and GND at 115 vias; 77 of them partial (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
At 115 via(s), on 67 net(s), the signal leaves a layer referenced by one of +3V6 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 33 served, 82 with none. 115 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +3V6 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. 77 of them are partial: another reference continues across through a stitching via of its net, so only part of the return has nowhere to go. The pure ones are listed first, then the partial ones with the farthest stitching via first.
- 'MGTTX112_0_N' at (-43.71, 398.58), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.01 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX112_0_N' at (-130.77, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 0.95 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX112_2_N' at (-126.33, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 5.31 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX112_2_N' at (-43.71, 363.09), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.01 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX116_0_N' at (-90.13, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 6.28 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX116_0_N' at (-43.71, 114.71), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 2.63 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX112_0_P' at (-43.71, 399.36), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.75 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX112_0_P' at (-130.14, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.54 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX113_2_N' at (-118.71, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 5.46 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX113_2_N' at (-43.71, 292.13), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.01 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX113_0_N' at (-122.52, 44.12), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 9.12 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'MGTTX113_0_N' at (-43.71, 327.61), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +3V6 on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 1.01 mm away; stitching none, 440.5 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +3V6 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 103 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B3V6%7CGND serves each with its own layer_image region; all of them lie in x -132.77..-8.77, y 42.12..401.36 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:+5V|GND38 nets change reference between +5V and GND at 51 vias; 42 of them partial (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
At 51 via(s), on 38 net(s), the signal leaves a layer referenced by one of +5V and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 10 served, 41 with none. 51 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether +5V and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. 42 of them are partial: another reference continues across through a stitching via of its net, so only part of the return has nowhere to go. The pure ones are listed first, then the partial ones with the farthest stitching via first.
- 'ARM_2V5_GPIO_PE10' at (-32.69, 11.96), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 5.49 mm away; stitching none, 216.1 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE13' at (-36.63, 11.29), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 6.66 mm away; stitching none, 194.0 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA-GPIO37' at (-116.39, -10.1), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.57 mm away; stitching none, 192.9 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA-GPIO36' at (-115.75, -10.09), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.89 mm away; stitching none, 191.3 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA-GPIO39' at (-118.29, -10.13), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.26 mm away; stitching none, 187.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA-GPIO38' at (-117.66, -10.1), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.26 mm away; stitching none, 183.8 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE12' at (-37.19, 12.31), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 6.72 mm away; stitching none, 177.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE15' at (-56.62, -4.54), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.96 mm away; stitching none, 177.6 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE14' at (-79.5, -16.22), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 3.61 mm away; stitching none, 173.9 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO25' at (-38.15, 12.08), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 5.81 mm away; stitching none, 163.2 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO28' at (-39.7, 13.06), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR; pure, no reference continues across; stitching none, 136.8 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'USB_HDP_P' at (-78.31, -16.22), TOP_LAYER -> MIDLAYER2: GND on MIDLAYER1 to +5V on PWR, GND on BOTTOM_LAYER; partial, GND continues through a via of GND 2.47 mm away; stitching none, 110.2 mm of track past the via on MIDLAYER2: At the 5 GHz knee of a 100 ps edge (500 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. +5V and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 39 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3A%2B5V%7CGND serves each with its own layer_image region; all of them lie in x -120.29..-30.69, y -18.25..27.81 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:CHASSIS_GND|FPGA-GPIO382 nets change reference between CHASSIS_GND and FPGA-GPIO38 at 2 vias, none with a reference that continues across (fastest: FPGA_GPIO17 at 2 ns 10-90 %, suggested by its name)
At 2 via(s), on 2 net(s), the signal leaves a layer referenced by one of CHASSIS_GND and FPGA-GPIO38 for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 2 with none. 2 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether CHASSIS_GND and FPGA-GPIO38 are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'FPGA_GPIO17' at (-32.16, 242.8), MIDLAYER1 -> BOTTOM_LAYER: CHASSIS_GND on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. CHASSIS_GND and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO25' at (-32.16, 171.83), MIDLAYER1 -> BOTTOM_LAYER: CHASSIS_GND on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. CHASSIS_GND and FPGA-GPIO38 are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3ACHASSIS_GND%7CFPGA-GPIO38 serves each with its own layer_image region; all of them lie in x -34.16..-30.16, y 169.83..244.8 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
refchange:FPGA-GPIO38|GND15 nets change reference between FPGA-GPIO38 and GND at 15 vias, none with a reference that continues across (fastest: NetCN1_U_WR_LINK_3_A7 at 100 ps 10-90 %, ASSUMED)
At 15 via(s), on 15 net(s), the signal leaves a layer referenced by one of FPGA-GPIO38 and GND for a layer referenced by the other, and no plane references both layers. Different nets: no via can carry the return across; only decoupling between the two planes near the via can. The capacitor carrying the return across was measured at each via, at the knee of the crossing net's edge against 50 ohm assumed: 15 with none. 15 of them at an ASSUMED edge (no edge on file for the net): state one (net_timing_state) and it is re-read. One decision covers the pair: whether FPGA-GPIO38 and GND are decoupled to each other near these vias. A via whose layers have more references than these two is a site of each pair it joins. None is partial: at every one, no reference continues across the via.
- 'I2C_DL_SD8' at (-32.16, 244.4), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_5 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.7 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SD12' at (-32.16, 173.43), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_3 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.6 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SC8' at (-32.16, 245.21), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_5 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SC12' at (-32.16, 174.24), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_3 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.2 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO23' at (-32.16, 226.36), MIDLAYER1 -> BOTTOM_LAYER: GND on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.1 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SC11' at (-32.16, 223.98), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'I2C_DL_SD11' at (-32.16, 223.16), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 7.0 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (10 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO17' at (-32.16, 242.8), MIDLAYER1 -> BOTTOM_LAYER: CHASSIS_GND on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'FPGA_GPIO25' at (-32.16, 171.83), MIDLAYER1 -> BOTTOM_LAYER: CHASSIS_GND on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (2 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'NetCN1_U_WR_LINK_4_B7' at (-32.16, 225.55), TOP_LAYER -> BOTTOM_LAYER: GND on MIDLAYER1 to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 6.3 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'ARM_2V5_GPIO_PE11' at (-32.16, 224.76), MIDLAYER1 -> BOTTOM_LAYER: +3V3_SFP_U_WR_LINK_4 on TOP_LAYER, GND on GND to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 5.9 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (20 ns 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- 'NetCN1_U_WR_LINK_5_A7' at (-32.16, 246.79), TOP_LAYER -> BOTTOM_LAYER: GND on MIDLAYER1 to FPGA-GPIO38 on MIDLAYER2; pure, no reference continues across; stitching none, 5.5 mm of track past the via on BOTTOM_LAYER: At the 5 GHz knee of a 100 ps edge (100 ps 10-90 %, assumed: no edge is on file for the net) no capacitor carries the return; only the planes do. FPGA-GPIO38 and GND are not a thin pair (at most 0.2 mm), so their own capacitance does not carry the return. To serve it, change layers across the same plane, or move the signal to a layer referenced to ground. None.
- and 3 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=refchange%3AFPGA-GPIO38%7CGND serves each with its own layer_image region; all of them lie in x -34.16..-30.16, y 169.83..248.79 mm (board frame, Y up).
The reference on each layer is the first plane the track meets leaving the via, anti-pads and the net's own copper skipped. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@BOTTOM_LAYER:+3V3_D|GND7 nets cross the split between the +3V3_D and GND planes on BOTTOM_LAYER at 19 places; 18 with a plane on the track's other side (fastest: DUPLEX_COLLISION at 100 ps 10-90 %, ASSUMED)
On BOTTOM_LAYER the +3V3_D and GND planes part, and 7 nets cross from one to the other at 19 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 18 of the 19 crossing(s) the track's other neighbour carries a plane, which the return can use there. 18 of the 19 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'SD' on MIDLAYER2 at (-43.11, 76.6), 0.21 mm; other side: no plane on PWR
- 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-41.89, 75.97), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-41.89, 76.6), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-42.27, 75.97), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-42.27, 76.6), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'DUPLEX_COLLISION' on MIDLAYER2 at (-42.6, 75.97), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'DUPLEX_COLLISION' on MIDLAYER2 at (-42.6, 76.6), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-33.35, 85.6), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-32.94, 74.68), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_1_N' on MIDLAYER2 at (-49.22, 77.68), 0.24 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_1_N' on MIDLAYER2 at (-48.46, 77.47), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_1_N' on MIDLAYER2 at (-48.21, 79.45), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- and 7 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40BOTTOM_LAYER%3A%2B3V3_D%7CGND serves each with its own layer_image region; all of them lie in x -50.44..-31.84, y 73.58..86.7 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@BOTTOM_LAYER:+3V3|GND12 nets cross the split between the +3V3 and GND planes on BOTTOM_LAYER at 28 places; 27 with a plane on the track's other side (fastest: DUPLEX_COLLISION at 100 ps 10-90 %, ASSUMED)
On BOTTOM_LAYER the +3V3 and GND planes part, and 12 nets cross from one to the other at 28 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 27 of the 28 crossing(s) the track's other neighbour carries a plane, which the return can use there. 27 of the 28 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'SD' on MIDLAYER2 at (-41.91, 71.32), 0.23 mm; other side: no plane on PWR
- 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-41.86, 72.72), 0.13 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-42.27, 72.77), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-41.93, 72.29), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'DUPLEX_COLLISION' on MIDLAYER2 at (-42.6, 72.77), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'DUPLEX_COLLISION' on MIDLAYER2 at (-41.93, 71.8), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-33.35, 90.96), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-33, 39.71), 7.42 mm; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-32.95, 92.59), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.97, 90.96), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.17, 92.59), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-29.27, 87), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- and 16 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40BOTTOM_LAYER%3A%2B3V3%7CGND serves each with its own layer_image region; all of them lie in x -49.39..-27.12, y 31.46..93.69 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@BOTTOM_LAYER:+5V|GND5 nets cross the split between the +5V and GND planes on BOTTOM_LAYER at 9 places; 8 with a plane on the track's other side (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On BOTTOM_LAYER the +5V and GND planes part, and 5 nets cross from one to the other at 9 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 8 of the 9 crossing(s) the track's other neighbour carries a plane, which the return can use there. 8 of the 9 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.13, 63.75), 0.21 mm; other side: no plane on PWR
- 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-35.33, 58.42), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-35.33, 57.96), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-32.52, 65.33), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-32.28, 54.53), 0.29 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.51, 43.94), 1.03 mm; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-32.13, 65.33), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-30.8, 63.75), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-30.8, 65.33), 0.21 mm; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40BOTTOM_LAYER%3A%2B5V%7CGND serves each with its own layer_image region; all of them lie in x -36.44..-29.8, y 42.45..66.43 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@MIDLAYER2:FPGA-GPIO38|FPGA-GPIO39102 nets cross the split between the FPGA-GPIO38 and FPGA-GPIO39 planes on MIDLAYER2 at 102 places, with no plane on the track's other side (fastest: FPGA-GPIO37 at 100 ps 10-90 %, ASSUMED)
On MIDLAYER2 the FPGA-GPIO38 and FPGA-GPIO39 planes part, and 102 nets cross from one to the other at 102 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 102 crossing(s) the track's other neighbour carries a plane, which the return can use there; 102 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'ARM_2V5_GPIO_PD10' on BOTTOM_LAYER at (-28.45, 119.74), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PD11' on BOTTOM_LAYER at (-28.45, 103.69), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-28.45, 387.56), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE10' on BOTTOM_LAYER at (-28.45, 210.14), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE11' on BOTTOM_LAYER at (-28.45, 226.2), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE12' on BOTTOM_LAYER at (-28.45, 174.66), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE13' on BOTTOM_LAYER at (-28.45, 190.71), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE14' on BOTTOM_LAYER at (-28.45, 139.17), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE15' on BOTTOM_LAYER at (-28.45, 155.23), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-28.45, 352.08), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-28.45, 368.13), 0.2 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-28.45, 316.59), 0.2 mm; other side: none: the signal layer is outermost
- and 90 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40MIDLAYER2%3AFPGA-GPIO38%7CFPGA-GPIO39 serves each with its own layer_image region; all of them lie in x -29.55..-27.35, y 97.36..390.34 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@MIDLAYER2:FPGA-GPIO38|GND80 nets cross the split between the FPGA-GPIO38 and GND planes on MIDLAYER2 at 80 places, with no plane on the track's other side (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On MIDLAYER2 the FPGA-GPIO38 and GND planes part, and 80 nets cross from one to the other at 80 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 80 crossing(s) the track's other neighbour carries a plane, which the return can use there; 80 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'ARM_2V5_GPIO_PD10' on BOTTOM_LAYER at (-29.82, 119.74), 1.48 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PD11' on BOTTOM_LAYER at (-29.03, 103.69), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-29.03, 387.56), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE10' on BOTTOM_LAYER at (-29.79, 210.14), 1.46 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE13' on BOTTOM_LAYER at (-29.34, 190.71), 1.79 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE14' on BOTTOM_LAYER at (-29.34, 139.17), 1.79 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE15' on BOTTOM_LAYER at (-29.34, 155.23), 1.79 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-29.32, 352.08), 1.76 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-29.32, 368.13), 1.76 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-29.38, 316.59), 1.87 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE5' on BOTTOM_LAYER at (-29.38, 332.65), 1.89 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE6' on BOTTOM_LAYER at (-30.05, 281.11), 1.71 mm; other side: none: the signal layer is outermost
- and 68 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40MIDLAYER2%3AFPGA-GPIO38%7CGND serves each with its own layer_image region; all of them lie in x -32.4..-27.93, y 97.36..390.34 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@MIDLAYER2:FPGA-GPIO39|GND102 nets cross the split between the FPGA-GPIO39 and GND planes on MIDLAYER2 at 102 places, with no plane on the track's other side (fastest: NetCN1_U_WR_LINK_1_A7 at 100 ps 10-90 %, ASSUMED)
On MIDLAYER2 the FPGA-GPIO39 and GND planes part, and 102 nets cross from one to the other at 102 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 0 of the 102 crossing(s) the track's other neighbour carries a plane, which the return can use there; 102 are on an outer layer, with no other neighbour. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'ARM_2V5_GPIO_PD10' on BOTTOM_LAYER at (-27.81, 119.74), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PD11' on BOTTOM_LAYER at (-27.81, 103.69), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-27.81, 387.56), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE10' on BOTTOM_LAYER at (-27.81, 210.14), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE11' on BOTTOM_LAYER at (-27.81, 226.2), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE12' on BOTTOM_LAYER at (-27.81, 174.66), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE13' on BOTTOM_LAYER at (-27.81, 190.71), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE14' on BOTTOM_LAYER at (-27.81, 139.17), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE15' on BOTTOM_LAYER at (-27.81, 155.23), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-27.81, 352.08), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-27.81, 368.13), 0.21 mm; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-27.81, 316.59), 0.21 mm; other side: none: the signal layer is outermost
- and 90 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40MIDLAYER2%3AFPGA-GPIO39%7CGND serves each with its own layer_image region; all of them lie in x -28.92..-26.71, y 97.36..394.28 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PWR:+3V6|+5V21 nets cross the split between the +3V6 and +5V planes on PWR at 21 places; 7 with a plane on the track's other side (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On PWR the +3V6 and +5V planes part, and 21 nets cross from one to the other at 21 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 7 of the 21 crossing(s) the track's other neighbour carries a plane, which the return can use there. 7 of the 21 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_2V5_GPIO_PE10' on MIDLAYER2 at (-22.25, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE12' on MIDLAYER2 at (-25.68, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE13' on MIDLAYER2 at (-24.56, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-28.63, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-27.51, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA-GPIO39' on MIDLAYER2 at (-29.34, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO21' on MIDLAYER2 at (-22.96, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO24' on MIDLAYER2 at (-25.07, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO25' on MIDLAYER2 at (-26.19, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO26' on MIDLAYER2 at (-23.47, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO27' on MIDLAYER2 at (-23.97, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA_GPIO28' on MIDLAYER2 at (-27.99, 46.74), 0.51 mm; other side: no plane on BOTTOM_LAYER
- and 9 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40PWR%3A%2B3V6%7C%2B5V serves each with its own layer_image region; all of them lie in x -44.36..-21.25, y 25.11..47.99 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@PWR:+5V|CHASSIS_GND6 nets cross the split between the +5V and CHASSIS_GND planes on PWR at 16 places; 11 with a plane on the track's other side (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
On PWR the +5V and CHASSIS_GND planes part, and 6 nets cross from one to the other at 16 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 11 of the 16 crossing(s) the track's other neighbour carries a plane, which the return can use there. 11 of the 16 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-47.91, 9.04), 0.72 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA-GPIO36' on MIDLAYER2 at (-55.04, 5.56), 0.72 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA-GPIO37' on MIDLAYER2 at (-55.04, 4.9), 0.72 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA-GPIO38' on MIDLAYER2 at (-50.14, 9.04), 0.72 mm; other side: no plane on BOTTOM_LAYER
- 'FPGA-GPIO39' on MIDLAYER2 at (-48.9, 9.04), 0.72 mm; other side: no plane on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-55.04, 1.91), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-55.04, 1.24), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-47.24, 9.04), 0.72 mm; other side: USB_5VBUS on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'FPGA-GPIO36' on MIDLAYER2 at (-51.56, 9.04), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'FPGA-GPIO37' on MIDLAYER2 at (-50.9, 9.04), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'FPGA-GPIO38' on MIDLAYER2 at (-107.11, -18.06), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- 'FPGA-GPIO38' on MIDLAYER2 at (-69.12, -18.06), 0.72 mm; other side: GND on BOTTOM_LAYER, 0.254 mm from the track against 0.127 mm to PWR: 67% of the return on PWR
- and 4 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40PWR%3A%2B5V%7CCHASSIS_GND serves each with its own layer_image region; all of them lie in x -109.58..-45.99, y -19.31..10.3 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@TOP_LAYER:+1V8_A|GND7 nets cross the split between the +1V8_A and GND planes on TOP_LAYER at 11 places; 10 with a plane on the track's other side (fastest: LINK_ACT at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +1V8_A and GND planes part, and 7 nets cross from one to the other at 11 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 10 of the 11 crossing(s) the track's other neighbour carries a plane, which the return can use there. 10 of the 11 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'TXO_P' on MIDLAYER1 at (-36.68, 60.97), 0.29 mm; other side: no plane on GND
- 'LINK_ACT' on MIDLAYER1 at (-45.27, 64.92), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'LINK_ACT' on MIDLAYER1 at (-45.27, 66.6), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'RXI_N' on MIDLAYER1 at (-42.22, 66.6), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'RXI_P' on MIDLAYER1 at (-42.01, 66.6), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'SPEED' on MIDLAYER1 at (-42.91, 66.6), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'TXO_N' on MIDLAYER1 at (-38.61, 63.19), 0.89 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'TXO_N' on MIDLAYER1 at (-36.68, 61.25), 0.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'TXO_P' on MIDLAYER1 at (-39.3, 63.59), 1.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'USB_INDICATOR' on MIDLAYER1 at (-42.55, 66.6), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'USB_INDICATOR' on MIDLAYER1 at (-41.21, 57.85), 0.26 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40TOP_LAYER%3A%2B1V8_A%7CGND serves each with its own layer_image region; all of them lie in x -46.27..-35.57, y 56.79..67.7 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@TOP_LAYER:+3V3|GND38 nets cross the split between the +3V3 and GND planes on TOP_LAYER at 184 places; 176 with a plane on the track's other side (fastest: LINK_ACT at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +3V3 and GND planes part, and 38 nets cross from one to the other at 184 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 176 of the 184 crossing(s) the track's other neighbour carries a plane, which the return can use there. 176 of the 184 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-29.54, 71.4), 0.47 mm; other side: no plane on GND
- 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-38.05, 40.81), 0.61 mm; other side: no plane on GND
- 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-34.04, 43.5), 0.51 mm; other side: no plane on GND
- 'FPGA_GPIO20' on MIDLAYER1 at (-33.5, 42.87), 0.29 mm; other side: no plane on GND
- 'FPGA_GPIO32' on MIDLAYER1 at (-30.53, 71.42), 0.21 mm; other side: no plane on GND
- 'FPGA_GPIO33' on MIDLAYER1 at (-31.37, 71.42), 0.21 mm; other side: no plane on GND
- 'SPEED' on MIDLAYER1 at (-38.47, 56.9), 0.32 mm; other side: no plane on GND
- 'USB_INDICATOR' on MIDLAYER1 at (-38.37, 57.79), 0.53 mm; other side: no plane on GND
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-36.12, 45.54), 0.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-33.51, 48.15), 1.08 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-32.44, 49.81), 0.82 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-32.44, 71.42), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- and 172 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40TOP_LAYER%3A%2B3V3%7CGND serves each with its own layer_image region; all of them lie in x -53.86..-19.14, y 24.24..89.62 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@TOP_LAYER:+5V|GND16 nets cross the split between the +5V and GND planes on TOP_LAYER at 35 places; 34 with a plane on the track's other side (fastest: MGTRX114_0_N at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the +5V and GND planes part, and 16 nets cross from one to the other at 35 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 34 of the 35 crossing(s) the track's other neighbour carries a plane, which the return can use there. 34 of the 35 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'FPGA_GPIO35' on MIDLAYER1 at (-39.7, 46.56), 0.37 mm; other side: no plane on GND
- 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-40.11, 39.34), 0.4 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-39.49, 39.38), 0.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-38.83, 40.03), 0.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO29' on MIDLAYER1 at (-40.73, 39.3), 0.4 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO32' on MIDLAYER1 at (-41.23, 39.37), 0.33 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO33' on MIDLAYER1 at (-41.37, 39.73), 0.88 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'FPGA_GPIO35' on MIDLAYER1 at (-40.16, 43.55), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX114_0_N' on MIDLAYER1 at (-57.1, 257.77), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX114_0_N' on MIDLAYER1 at (-56.44, 257.77), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX114_0_P' on MIDLAYER1 at (-57.3, 257.77), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX114_0_P' on MIDLAYER1 at (-56.24, 257.77), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- and 23 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40TOP_LAYER%3A%2B5V%7CGND serves each with its own layer_image region; all of them lie in x -58.87..-37.73, y 38.2..258.87 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
split@TOP_LAYER:CHASSIS_GND|GND95 nets cross the split between the CHASSIS_GND and GND planes on TOP_LAYER at 138 places; 134 with a plane on the track's other side (fastest: MGTRX115_0_N at 100 ps 10-90 %, ASSUMED)
On TOP_LAYER the CHASSIS_GND and GND planes part, and 95 nets cross from one to the other at 138 place(s). The return current cannot follow a track across; it detours to wherever the two planes are joined (a stitching capacitor, or the source), and the loop it opens radiates and couples. One decision covers the boundary: whether it is stitched near these crossings, or the nets crossing it are slow enough not to care. Tracks that run ALONG this split, down the slot rather than across it, are a finding of their own: theirs is an impedance step, not a detour. At 134 of the 138 crossing(s) the track's other neighbour carries a plane, which the return can use there. 134 of the 138 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-28.94, 74.22), 0.27 mm; other side: no plane on GND
- 'FPGA_GPIO29' on MIDLAYER1 at (-30.25, 74.2), 0.21 mm; other side: no plane on GND
- 'FPGA_GPIO34' on MIDLAYER1 at (-34.9, 88.59), 2.1 mm; other side: no plane on GND
- 'FPGA_GPIO34' on MIDLAYER1 at (-34.9, 74.22), 0.26 mm; other side: no plane on GND
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-31.7, 74.2), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-28.7, 89.53), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-28.7, 90.38), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-26.55, 94.24), 0.29 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-23.14, 118.95), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-35.18, 88.59), 2.1 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-35.18, 90.38), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-35.13, 74.2), 0.21 mm; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- and 126 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=split%40TOP_LAYER%3ACHASSIS_GND%7CGND serves each with its own layer_image region; all of them lie in x -57.85..-18.84, y 73.09..405.11 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:-44.52,79.22'SD' crosses where the outline of the GND plane on BOTTOM_LAYER is drawn back, at 1 place, the longest 0.1 mm (fastest: SD at 100 ps 10-90 %, ASSUMED)
Along 'SD' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 0.1 mm under the track with no copper, at (-44.52, 79.22), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-10.4, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'SD' on MIDLAYER2 at (-44.52, 79.22), 0.1 mm over no copper; other side: no plane on PWR
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3A-44.52%2C79.22 serves each with its own layer_image region; all of them lie in x -45.55..-43.48, y 78.18..80.25 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -42.71,59.69|-40.31,62.943 nets cross one void in the GND plane on BOTTOM_LAYER at 4 places, the longest 1.41 mm; 1 over tracks of other nets routed inside it (fastest: SD at 100 ps 10-90 %, ASSUMED)
Along 'USB_HDP_N' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 1.41 mm under the track with copper of NetIC7_5, not a plane, at (-41.89, 62.24), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.41 mm). 4 places on 3 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -42.71..-40.31, y 59.69..62.94. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 2 of the 4 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'SD' on MIDLAYER2 at (-41.3, 62.1), 0.52 mm over copper of NetIC7_5, not a plane; other side: no plane on PWR
- 'SD' on MIDLAYER2 at (-40.96, 61.61), 0.21 mm over no copper, to the end of the track; other side: no plane on PWR
- 'USB_HDP_N' on MIDLAYER2 at (-41.89, 62.24), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of NetIC7_5, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'USB_HDP_P' on MIDLAYER2 at (-42.09, 62.24), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of NetIC7_5, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-42.71%2C59.69%7C-40.31%2C62.94 serves each with its own layer_image region; all of them lie in x -43.09..-39.74, y 60.39..63.94 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -47.22,23.72|-17.65,26.1223 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 5 places, the longest 8.08 mm; 31 over tracks of other nets routed inside it (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
Along 'USB_CPU_DBG_N' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 8.08 mm under the track with copper of FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, not a plane, at (-29.47, 25.25), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 31 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 5 places on 23 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -47.22..-17.65, y 23.72..26.12. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 21 of the 31 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE10' on MIDLAYER2 at (-22.25, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE12' on MIDLAYER2 at (-25.68, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE13' on MIDLAYER2 at (-24.56, 25.61), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-28.63, 25.61), 0.73 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-27.51, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO39' on MIDLAYER2 at (-29.62, 25.09), 0.88 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO21' on MIDLAYER2 at (-22.96, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO24' on MIDLAYER2 at (-25.07, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO25' on MIDLAYER2 at (-26.19, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO26' on MIDLAYER2 at (-23.47, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO27' on MIDLAYER2 at (-23.97, 25.61), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO28' on MIDLAYER2 at (-27.99, 25.09), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO30' on MIDLAYER2 at (-26.62, 25.61), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO31' on MIDLAYER2 at (-27.05, 25.61), 0.72 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_CPU_DBG_N' on BOTTOM_LAYER at (-29.47, 25.25), 8.08 mm over copper of FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on BOTTOM_LAYER at (-22.6, 25.45), 7.87 mm over copper of FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_3V3_GPIO_PB4' on MIDLAYER2 at (-35.05, 25.09), 0.88 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_3V3_GPIO_PB5' on MIDLAYER2 at (-35.28, 25.61), 1.02 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_CPU_DBG_N' on BOTTOM_LAYER at (-35.27, 25.25), 1.45 mm over copper of ARM_3V3_GPIO_PB5, ARM_3V3_GPIO_PB4, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on BOTTOM_LAYER at (-35.09, 25.45), 1.29 mm over copper of ARM_3V3_GPIO_PB5, ARM_3V3_GPIO_PB4, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'FPGA-GPIO36' on MIDLAYER2 at (-33.34, 25.09), 0.91 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO37' on MIDLAYER2 at (-32.51, 25.61), 0.74 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_CPU_DBG_N' on BOTTOM_LAYER at (-32.84, 25.25), 1.3 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on BOTTOM_LAYER at (-32.75, 25.45), 1.09 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'FPGA-GPIO38' on MIDLAYER2 at (-31.46, 25.09), 1.02 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_CPU_DBG_N' on BOTTOM_LAYER at (-31.3, 25.25), 1.21 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on BOTTOM_LAYER at (-31.1, 25.45), 1.21 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'USB_CPU_DBG_N' on BOTTOM_LAYER at (-43.62, 23.98), 1.02 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on BOTTOM_LAYER at (-43.42, 24.18), 1.02 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'USB_HDP_N' on MIDLAYER2 at (-43.48, 24.34), 1.02 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_HDP_P' on MIDLAYER2 at (-44.28, 23.82), 1.02 mm over copper of USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-47.22%2C23.72%7C-17.65%2C26.12 serves each with its own layer_image region; all of them lie in x -45.49..-20.99, y 22.72..26.71 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -50.46,131.9|-46.43,135.734 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 7 places, the longest 3.68 mm; 5 over tracks of other nets routed inside it (fastest: MGTTX115_3_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTTX115_3_N' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 3.68 mm under the track with copper of WR_LINK0_LED_SYNCED_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C3, not a plane, at (-48.34, 135.03), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 5 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 8 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.6 mm). 7 places on 4 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -50.46..-46.43, y 131.9..135.73. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 8 of the 11 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'MGTTX115_3_N' on MIDLAYER2 at (-48.34, 135.03), 3.68 mm, running ALONG the bare copper for 2.6 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX115_3_P' on MIDLAYER2 at (-48.54, 135.03), 3.68 mm, running ALONG the bare copper for 2.6 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_2, NetCN1_U_WR_LINK_2_C3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'WR_LINK0_LED_SYNCED_U_WR_LINK_2' on BOTTOM_LAYER at (-49.7, 133.16), 1.04 mm over copper of MGTTX115_3_N, MGTTX115_3_P, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_2' on BOTTOM_LAYER at (-48.7, 134.14), 0.72 mm over copper of MGTTX115_3_P, MGTTX115_3_N, not a plane; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_2' on BOTTOM_LAYER at (-49.7, 134.91), 1.04 mm over copper of MGTTX115_3_N, MGTTX115_3_P, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'MGTTX115_3_P' on MIDLAYER2 at (-49.33, 135.18), 1.55 mm, running ALONG the bare copper for 1.14 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_3_P' on MIDLAYER2 at (-49.33, 133.42), 1.55 mm, running ALONG the bare copper for 1.14 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_3_N' on MIDLAYER2 at (-49.53, 135.03), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_3_N' on MIDLAYER2 at (-50.32, 135.03), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_3_N' on MIDLAYER2 at (-49.53, 133.27), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_3_N' on MIDLAYER2 at (-50.32, 133.27), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-50.46%2C131.9%7C-46.43%2C135.73 serves each with its own layer_image region; all of them lie in x -51.32..-47.08, y 131.05..136.73 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -50.46,146.45|-46.45,149.934 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 6 places, the longest 5.34 mm; 5 over tracks of other nets routed inside it (fastest: MGTTX115_2_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTTX115_2_N' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 5.34 mm under the track with copper of WR_LINK1_LED_SYNCED_U_WR_LINK_2, NetCN1_U_WR_LINK_2_E1, WR_LINK1_LED_WRMODE_U_WR_LINK_2, NetCN1_U_WR_LINK_2_E3, not a plane, at (-48.5, 149.23), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 5 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 7 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 4.37 mm). 6 places on 4 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -50.46..-46.45, y 146.45..149.93. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 10 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'MGTTX115_2_N' on MIDLAYER2 at (-48.5, 149.23), 5.34 mm, running ALONG the bare copper for 4.37 mm, not across it over copper of WR_LINK1_LED_SYNCED_U_WR_LINK_2, NetCN1_U_WR_LINK_2_E1, WR_LINK1_LED_WRMODE_U_WR_LINK_2, NetCN1_U_WR_LINK_2_E3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX115_2_P' on MIDLAYER2 at (-48.7, 149.2), 4.78 mm, running ALONG the bare copper for 4.02 mm, not across it over copper of WR_LINK1_LED_SYNCED_U_WR_LINK_2, WR_LINK1_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'WR_LINK1_LED_SYNCED_U_WR_LINK_2' on BOTTOM_LAYER at (-49.27, 147.03), 1.75 mm, running ALONG the bare copper for 0.76 mm, not across it over copper of MGTTX115_2_N, MGTTX115_2_P, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'WR_LINK1_LED_WRMODE_U_WR_LINK_2' on BOTTOM_LAYER at (-48.34, 148.41), 0.72 mm over copper of MGTTX115_2_P, MGTTX115_2_N, not a plane; other side: none: the signal layer is outermost / 'WR_LINK1_LED_WRMODE_U_WR_LINK_2' on BOTTOM_LAYER at (-49.21, 148.62), 1 mm over copper of MGTTX115_2_N, MGTTX115_2_P, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'MGTTX115_2_P' on MIDLAYER2 at (-49.36, 149.3), 1.52 mm, running ALONG the bare copper for 1.22 mm, not across it over copper of WR_LINK1_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_2_N' on MIDLAYER2 at (-49.56, 149.23), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK1_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_2_N' on MIDLAYER2 at (-50.23, 149.23), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK1_LED_WRMODE_U_WR_LINK_2, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_2_P' on MIDLAYER2 at (-50.43, 149.23), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_2_N' on MIDLAYER2 at (-50.37, 148.16), 0.27 mm over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-50.46%2C146.45%7C-46.45%2C149.93 serves each with its own layer_image region; all of them lie in x -51.46..-47.24, y 145.74..150.93 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -50.46,167.38|-46.43,171.214 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 6 places, the longest 3.68 mm; 6 over tracks of other nets routed inside it (fastest: MGTTX115_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTTX115_1_N' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 3.68 mm under the track with copper of WR_LINK0_LED_SYNCED_U_WR_LINK_3, NetCN1_U_WR_LINK_3_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_3, NetCN1_U_WR_LINK_3_C3, not a plane, at (-48.65, 168.76), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 6 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 6 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.6 mm). 6 places on 4 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -50.46..-46.43, y 167.38..171.21. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 11 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'MGTTX115_1_N' on MIDLAYER2 at (-48.65, 168.76), 3.68 mm, running ALONG the bare copper for 2.6 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_3, NetCN1_U_WR_LINK_3_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_3, NetCN1_U_WR_LINK_3_C3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX115_1_P' on MIDLAYER2 at (-48.86, 168.72), 3.68 mm, running ALONG the bare copper for 2.36 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_3, WR_LINK0_LED_WRMODE_U_WR_LINK_3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'WR_LINK0_LED_SYNCED_U_WR_LINK_3' on BOTTOM_LAYER at (-49.01, 167.96), 0.83 mm over copper of MGTTX115_1_P, MGTTX115_1_N, not a plane; other side: none: the signal layer is outermost / 'WR_LINK0_LED_SYNCED_U_WR_LINK_3' on BOTTOM_LAYER at (-49.49, 168.44), 0.6 mm over copper of MGTTX115_1_N, MGTTX115_1_P, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_3' on BOTTOM_LAYER at (-49.02, 169.72), 0.8 mm over copper of MGTTX115_1_P, MGTTX115_1_N, not a plane; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_3' on BOTTOM_LAYER at (-49.49, 170.19), 0.6 mm over copper of MGTTX115_1_N, MGTTX115_1_P, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'MGTTX115_1_N' on MIDLAYER2 at (-49.85, 168.76), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_1_P' on MIDLAYER2 at (-49.64, 168.76), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_1_N' on MIDLAYER2 at (-49.85, 170.51), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_1_P' on MIDLAYER2 at (-49.64, 170.51), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX115_1_N' on MIDLAYER2 at (-47.64, 171.15), 0.2 mm over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-50.46%2C167.38%7C-46.43%2C171.21 serves each with its own layer_image region; all of them lie in x -50.85..-46.56, y 166.53..172.21 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -50.46,202.87|-46.43,206.74 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 6 places, the longest 3.68 mm; 5 over tracks of other nets routed inside it (fastest: MGTTX114_3_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTTX114_3_N' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 3.68 mm under the track with copper of WR_LINK0_LED_SYNCED_U_WR_LINK_4, WR_LINK0_LED_WRMODE_U_WR_LINK_4, not a plane, at (-48.81, 204.19), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 5 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 6 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 2.49 mm). 6 places on 4 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -50.46..-46.43, y 202.87..206.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 10 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'MGTTX114_3_N' on MIDLAYER2 at (-48.81, 204.19), 3.68 mm, running ALONG the bare copper for 2.49 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_4, WR_LINK0_LED_WRMODE_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX114_3_P' on MIDLAYER2 at (-49.01, 204.32), 2.48 mm, running ALONG the bare copper for 1.09 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_4, WR_LINK0_LED_WRMODE_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'WR_LINK0_LED_SYNCED_U_WR_LINK_4' on BOTTOM_LAYER at (-49.16, 203.6), 0.9 mm over copper of MGTTX114_3_N, MGTTX114_3_P, not a plane; other side: none: the signal layer is outermost / 'WR_LINK0_LED_SYNCED_U_WR_LINK_4' on BOTTOM_LAYER at (-49.64, 204.07), 0.38 mm over copper of MGTTX114_3_P, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_4' on BOTTOM_LAYER at (-49.16, 205.35), 0.87 mm over copper of MGTTX114_3_N, MGTTX114_3_P, not a plane; other side: none: the signal layer is outermost
- 'MGTTX114_3_N' on MIDLAYER2 at (-50, 204.24), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX114_3_P' on MIDLAYER2 at (-49.8, 204.24), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX114_3_N' on MIDLAYER2 at (-50, 205.99), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX114_3_P' on MIDLAYER2 at (-49.8, 205.99), 1.41 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_4, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX114_3_N' on MIDLAYER2 at (-47.63, 206.57), 0.35 mm over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-50.46%2C202.87%7C-46.43%2C206.7 serves each with its own layer_image region; all of them lie in x -51..-46.56, y 202.02..207.7 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -50.46,96.41|-46.43,100.257 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 6 places, the longest 3.93 mm; 5 over tracks of other nets routed inside it (fastest: MGTTX116_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTTX116_1_P' on MIDLAYER2, the GND plane on BOTTOM_LAYER has 3.93 mm under the track with copper of WR_LINK0_LED_SYNCED_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C3, not a plane, at (-48.12, 99.54), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 5 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 7 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.81 mm). 6 places on 7 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -50.46..-46.43, y 96.41..100.25. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 7 of the 10 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'MGTTX116_1_N' on MIDLAYER2 at (-48.29, 97.79), 3.56 mm, running ALONG the bare copper for 1.54 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX116_1_P' on MIDLAYER2 at (-48.12, 99.54), 3.93 mm, running ALONG the bare copper for 1.53 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C1, WR_LINK0_LED_WRMODE_U_WR_LINK_1, NetCN1_U_WR_LINK_1_C3, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'NetCN1_U_WR_LINK_1_C3' on BOTTOM_LAYER at (-47.61, 99.54), 0.74 mm over copper of MGTTX116_1_P, MGTTX116_1_N, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'WR_LINK0_LED_SYNCED_U_WR_LINK_1' on BOTTOM_LAYER at (-48.64, 96.83), 0.72 mm over copper of MGTTX116_1_P, MGTTX116_1_N, not a plane; other side: none: the signal layer is outermost / 'WR_LINK0_LED_WRMODE_U_WR_LINK_1' on BOTTOM_LAYER at (-48.64, 98.65), 0.72 mm over copper of MGTTX116_1_P, MGTTX116_1_N, not a plane; other side: none: the signal layer is outermost
- 'MGTTX116_0_N' on MIDLAYER2 at (-49.93, 97.63), 2.46 mm, running ALONG the bare copper for 1.81 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_0_P' on MIDLAYER2 at (-49.93, 97.83), 1.71 mm, running ALONG the bare copper for 1.39 mm, not across it over copper of WR_LINK0_LED_SYNCED_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_0_P' on MIDLAYER2 at (-49.81, 99.82), 1.31 mm, running ALONG the bare copper for 1.29 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_0_N' on MIDLAYER2 at (-49.81, 99.61), 1.31 mm, running ALONG the bare copper for 1.3 mm, not across it over copper of WR_LINK0_LED_WRMODE_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'MGTTX116_0_N' on MIDLAYER2 at (-48.75, 100.18), 0.47 mm, running ALONG the bare copper for 0.35 mm, not across it over no copper; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-50.46%2C96.41%7C-46.43%2C100.25 serves each with its own layer_image region; all of them lie in x -51.46..-46.47, y 95.57..101.25 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@BOTTOM_LAYER:hole -71.07,-9.78|-57.37,-3.868 nets cross one void in the GND plane on BOTTOM_LAYER and the GND plane on MIDLAYER2 at 3 places, the longest 12.57 mm; 8 over tracks of other nets routed inside it (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
Along 'ARM_2V5_GPIO_PE14' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 12.57 mm under the track with copper of FPGA-GPIO39, USB_HDP_N, ARM_3V3_GPIO_PB1, FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, USB_HDP_P, not a plane, at (-61.28, -5.86), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 8 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 3 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 6.21 mm). 3 places on 8 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -71.07..-57.37, y -9.78..-3.86. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 6 of the 8 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE14' on BOTTOM_LAYER at (-61.28, -5.86), 12.57 mm, running ALONG the bare copper for 6.21 mm, not across it over copper of FPGA-GPIO39, USB_HDP_N, ARM_3V3_GPIO_PB1, FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, USB_HDP_P, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB1' on MIDLAYER2 at (-67.56, -7.77), 1.23 mm over copper of ARM_2V5_GPIO_PE14, not a plane; other side: no plane on PWR / 'FPGA-GPIO36' on MIDLAYER2 at (-65.72, -7.29), 0.73 mm over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO37' on MIDLAYER2 at (-65.32, -7.6), 0.73 mm over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO38' on MIDLAYER2 at (-63.84, -7.29), 0.73 mm over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO39' on MIDLAYER2 at (-59.49, -4.11), 0.52 mm over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'USB_HDP_P' on MIDLAYER2 at (-69.24, -7.59), 1.72 mm, running ALONG the bare copper for 1 mm, not across it over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'USB_HDP_N' on MIDLAYER2 at (-69.07, -7.71), 1.63 mm, running ALONG the bare copper for 0.89 mm, not across it over copper of ARM_2V5_GPIO_PE14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40BOTTOM_LAYER%3Ahole%20-71.07%2C-9.78%7C-57.37%2C-3.86 serves each with its own layer_image region; all of them lie in x -70.85..-58.06, y -9.67..-3.01 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER1:hole -135.62,37.77|-64.92,53.123 nets cross one void in the GND plane on MIDLAYER1 and the GND plane on TOP_LAYER at 1 place, the longest 1.02 mm; 3 over tracks of other nets routed inside it (fastest: NetQ2_1 at 100 ps 10-90 %, ASSUMED)
Along 'NetQ2_1' on MIDLAYER1, the GND plane on TOP_LAYER has 1.02 mm under the track with copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane, at (-77.61, 38.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 3 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. What cleared it: the hole at x -135.62..-64.92, y 37.77..53.12. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 3 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'NetQ2_1' on MIDLAYER1 at (-77.61, 38.18), 1.02 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'USB_CPU_DBG_N' on TOP_LAYER at (-77.83, 38.18), 0.95 mm over copper of NetQ2_1, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on TOP_LAYER at (-78.11, 38.18), 0.95 mm over copper of NetQ2_1, not a plane; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER1%3Ahole%20-135.62%2C37.77%7C-64.92%2C53.12 serves each with its own layer_image region; all of them lie in x -79.48..-76.46, y 36.84..39.51 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER1:hole -188.63,95.56|-180.39,105.052 nets cross one void in the GND plane on MIDLAYER1 at 2 places, the longest 0.78 mm; 2 over tracks of other nets routed inside it (fastest: NetIC9_23 at 100 ps 10-90 %, ASSUMED)
Along 'VREG5' on TOP_LAYER, the GND plane on MIDLAYER1 has 0.78 mm under the track with copper of ENC, not a plane, at (-183.45, 102.18), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -188.63..-180.39, y 95.56..105.05. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'VREG5' on TOP_LAYER at (-183.45, 102.18), 0.78 mm over copper of ENC, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'NetIC9_23' on TOP_LAYER at (-185.58, 96.2), 0.48 mm over copper of VREG5, not a plane, to the end of the track; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER1%3Ahole%20-188.63%2C95.56%7C-180.39%2C105.05 serves each with its own layer_image region; all of them lie in x -186.81..-182.11, y 94.97..103.4 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER2:-30.91,106.18'FPGA-GPIO36' crosses where the outline of the GND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.39 mm (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
Along 'FPGA-GPIO36' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 0.39 mm under the track with no copper, at (-30.91, 106.18), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'FPGA-GPIO36' on BOTTOM_LAYER at (-30.91, 106.18), 0.39 mm over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER2%3A-30.91%2C106.18 serves each with its own layer_image region; all of them lie in x -32.11..-29.72, y 105.18..107.18 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER2:-31.85,83.26'MODE_DEF0' crosses where the outline of the GND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.39 mm (fastest: MODE_DEF0 at 100 ps 10-90 %, ASSUMED)
Along 'MODE_DEF0' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 0.39 mm under the track with no copper, at (-31.85, 83.26), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'MODE_DEF0' on BOTTOM_LAYER at (-31.85, 83.26), 0.39 mm over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER2%3A-31.85%2C83.26 serves each with its own layer_image region; all of them lie in x -32.85..-30.85, y 82.07..84.46 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER2:-49.02,219.4'WR_LINK1_LED_WRMODE_U_WR_LINK_4' crosses where the outline of the GND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.1 mm (fastest: WR_LINK1_LED_WRMODE_U_WR_LINK_4 at 100 ps 10-90 %, ASSUMED)
Along 'WR_LINK1_LED_WRMODE_U_WR_LINK_4' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 0.1 mm under the track with no copper, at (-49.02, 219.4), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'WR_LINK1_LED_WRMODE_U_WR_LINK_4' on BOTTOM_LAYER at (-49.02, 219.4), 0.1 mm over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER2%3A-49.02%2C219.4 serves each with its own layer_image region; all of them lie in x -50.04..-47.96, y 218.38..220.43 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@MIDLAYER2:-49.1,98.83'WR_LINK0_LED_WRMODE_U_WR_LINK_1' crosses where the outline of the GND plane on MIDLAYER2 is drawn back, at 1 place, the longest 0.5 mm (fastest: WR_LINK0_LED_WRMODE_U_WR_LINK_1 at 100 ps 10-90 %, ASSUMED)
Along 'WR_LINK0_LED_WRMODE_U_WR_LINK_1' on BOTTOM_LAYER, the GND plane on MIDLAYER2 has 0.5 mm under the track with no copper, at (-49.1, 98.83), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'WR_LINK0_LED_WRMODE_U_WR_LINK_1' on BOTTOM_LAYER at (-49.1, 98.83), 0.5 mm over no copper; other side: none: the signal layer is outermost
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40MIDLAYER2%3A-49.1%2C98.83 serves each with its own layer_image region; all of them lie in x -50.27..-47.92, y 97.65..100.01 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:-37.16,57.79'USB_INDICATOR' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 0.3 mm (fastest: USB_INDICATOR at 500 ps 10-90 %, suggested by its name)
Along 'USB_INDICATOR' on MIDLAYER1, the GND plane on TOP_LAYER has 0.3 mm under the track with no copper, at (-37.16, 57.79), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'USB_INDICATOR' on MIDLAYER1 at (-37.16, 57.79), 0.3 mm over no copper; other side: no plane on GND
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3A-37.16%2C57.79 serves each with its own layer_image region; all of them lie in x -38.31..-36.01, y 56.79..58.79 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:-37.69,57.79'USB_INDICATOR' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 0.3 mm (fastest: USB_INDICATOR at 500 ps 10-90 %, suggested by its name)
Along 'USB_INDICATOR' on MIDLAYER1, the GND plane on TOP_LAYER has 0.3 mm under the track with no copper, at (-37.69, 57.79), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'USB_INDICATOR' on MIDLAYER1 at (-37.69, 57.79), 0.3 mm over no copper; other side: no plane on GND
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3A-37.69%2C57.79 serves each with its own layer_image region; all of them lie in x -38.85..-36.54, y 56.79..58.79 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:-42.72,85.62'USB_INDICATOR' crosses where the outline of the GND plane on TOP_LAYER is drawn back, at 1 place, the longest 0.37 mm (fastest: USB_INDICATOR at 500 ps 10-90 %, suggested by its name)
Along 'USB_INDICATOR' on MIDLAYER1, the GND plane on TOP_LAYER has 0.37 mm under the track with copper of GND, not a plane, at (-42.72, 85.62), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 0.28 mm). No hole cleared it: the outline of the pour at x -42.55..-39.65, y 84.97..85.68 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'USB_INDICATOR' on MIDLAYER1 at (-42.72, 85.62), 0.37 mm, running ALONG the bare copper for 0.28 mm, not across it over copper of GND, not a plane, to the end of the track; other side: no plane on GND
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3A-42.72%2C85.62 serves each with its own layer_image region; all of them lie in x -43.95..-41.55, y 84.45..86.85 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:copper of DUPLEX_COLLISION4 nets cross where the GND plane on TOP_LAYER is drawn back round copper of DUPLEX_COLLISION, at 5 places, the longest 1.53 mm (fastest: MGTRX116_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX116_1_P' on MIDLAYER1, the GND plane on TOP_LAYER has 1.53 mm under the track with copper of DUPLEX_COLLISION, not a plane, at (-46.09, 87.68), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.24 mm). 5 places on 4 net(s) cross it, listed below, the longest first. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 4 of the 5 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_3V3_GPIO_PB2' on MIDLAYER1 at (-44.63, 87.1), 1.47 mm, running ALONG the bare copper for 1.24 mm, not across it over copper of DUPLEX_COLLISION, not a plane; other side: no plane on GND
- 'MGTRX116_1_P' on MIDLAYER1 at (-46.09, 87.68), 1.53 mm, running ALONG the bare copper for 1.12 mm, not across it over copper of DUPLEX_COLLISION, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'ARM_3V3_GPIO_PB3' on MIDLAYER1 at (-44.96, 87.5), 1.46 mm over copper of DUPLEX_COLLISION, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_1_P' on MIDLAYER1 at (-46.09, 87.15), 1.35 mm over copper of DUPLEX_COLLISION, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_1_N' on MIDLAYER1 at (-46.09, 87.89), 1.21 mm over copper of DUPLEX_COLLISION, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Acopper%20of%20DUPLEX_COLLISION serves each with its own layer_image region; all of them lie in x -47.54..-43.63, y 85.77..89.23 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:copper of DUPLEX_COLLISION,SPEED'LINK_ACT' crosses where the GND plane on TOP_LAYER is drawn back round copper of DUPLEX_COLLISION, SPEED, at 1 place, the longest 1.28 mm (fastest: LINK_ACT at 100 ps 10-90 %, ASSUMED)
Along 'LINK_ACT' on MIDLAYER1, the GND plane on TOP_LAYER has 1.28 mm under the track with copper of SPEED, DUPLEX_COLLISION, not a plane, at (-37.34, 56.96), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. No crossing has a plane on the track's other side, so the whole return meets the break.
- 'LINK_ACT' on MIDLAYER1 at (-37.34, 56.96), 1.28 mm over copper of SPEED, DUPLEX_COLLISION, not a plane, to the end of the track; other side: no plane on GND
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Acopper%20of%20DUPLEX_COLLISION%2CSPEED serves each with its own layer_image region; all of them lie in x -39.24..-36.16, y 55.47..58.4 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:copper of USB_INDICATOR3 nets cross where the GND plane on TOP_LAYER is drawn back round copper of USB_INDICATOR, at 3 places, the longest 1.61 mm (fastest: MGTRX116_1_P at 100 ps 10-90 %, ASSUMED)
Along 'ARM_3V3_GPIO_PB3' on MIDLAYER1, the GND plane on TOP_LAYER has 1.61 mm under the track with copper of USB_INDICATOR, not a plane, at (-44.96, 85.94), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 1 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.14 mm). 3 places on 3 net(s) cross it, listed below, the longest first. No hole cleared it: the outline of the pour at x -207.68..-11.68, y -20.17..411.58 is drawn back there. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 2 of the 3 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'ARM_3V3_GPIO_PB2' on MIDLAYER1 at (-44.63, 86.26), 1.56 mm, running ALONG the bare copper for 1.14 mm, not across it over copper of USB_INDICATOR, not a plane; other side: no plane on GND
- 'ARM_3V3_GPIO_PB3' on MIDLAYER1 at (-44.96, 85.94), 1.61 mm over copper of USB_INDICATOR, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX116_1_P' on MIDLAYER1 at (-46.09, 86.21), 1.35 mm over copper of USB_INDICATOR, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Acopper%20of%20USB_INDICATOR serves each with its own layer_image region; all of them lie in x -47.54..-43.63, y 84.13..87.59 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -103.56,47.96|-102.1,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.44 mm (fastest: MGTRX115_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX115_0_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.44 mm under the track with copper of MGTRX115_0_N, not a plane, at (-102.93, 49.37), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.75 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -103.56..-102.1, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX115_0_N' on MIDLAYER1 at (-102.73, 49.93), 1.32 mm, running ALONG the bare copper for 0.76 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX115_0_P' on MIDLAYER1 at (-102.93, 49.37), 2.44 mm, running ALONG the bare copper for 1.75 mm, not across it over copper of MGTRX115_0_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-103.56%2C47.96%7C-102.1%2C50.7 serves each with its own layer_image region; all of them lie in x -104.15..-101.11, y 47.41..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -105.47,47.96|-104.01,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.46 mm (fastest: MGTRX114_3_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX114_3_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.46 mm under the track with copper of MGTRX114_3_N, not a plane, at (-104.84, 49.36), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.77 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -105.47..-104.01, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX114_3_N' on MIDLAYER1 at (-104.64, 49.92), 1.35 mm, running ALONG the bare copper for 0.73 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX114_3_P' on MIDLAYER1 at (-104.84, 49.36), 2.46 mm, running ALONG the bare copper for 1.77 mm, not across it over copper of MGTRX114_3_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-105.47%2C47.96%7C-104.01%2C50.7 serves each with its own layer_image region; all of them lie in x -106.06..-103.02, y 47.39..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -107.37,47.96|-105.91,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.5 mm (fastest: MGTRX114_2_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX114_2_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.5 mm under the track with copper of MGTRX114_2_N, not a plane, at (-106.74, 49.35), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.78 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -107.37..-105.91, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX114_2_N' on MIDLAYER1 at (-106.54, 49.9), 1.3 mm, running ALONG the bare copper for 0.77 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX114_2_P' on MIDLAYER1 at (-106.74, 49.35), 2.5 mm, running ALONG the bare copper for 1.78 mm, not across it over copper of MGTRX114_2_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-107.37%2C47.96%7C-105.91%2C50.7 serves each with its own layer_image region; all of them lie in x -107.96..-104.92, y 47.34..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -109.28,47.96|-107.82,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.48 mm (fastest: MGTRX114_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX114_1_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.48 mm under the track with copper of MGTRX114_1_N, not a plane, at (-108.65, 49.36), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.72 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -109.28..-107.82, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX114_1_N' on MIDLAYER1 at (-108.45, 49.92), 1.33 mm, running ALONG the bare copper for 0.79 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX114_1_P' on MIDLAYER1 at (-108.65, 49.36), 2.48 mm, running ALONG the bare copper for 1.72 mm, not across it over copper of MGTRX114_1_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-109.28%2C47.96%7C-107.82%2C50.7 serves each with its own layer_image region; all of them lie in x -109.87..-106.83, y 47.34..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -111.18,47.96|-109.72,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.53 mm (fastest: MGTRX114_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX114_0_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.53 mm under the track with copper of MGTRX114_0_N, not a plane, at (-110.55, 49.35), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.69 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -111.18..-109.72, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX114_0_N' on MIDLAYER1 at (-110.35, 49.9), 1.36 mm, running ALONG the bare copper for 0.63 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX114_0_P' on MIDLAYER1 at (-110.55, 49.35), 2.53 mm, running ALONG the bare copper for 1.69 mm, not across it over copper of MGTRX114_0_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-111.18%2C47.96%7C-109.72%2C50.7 serves each with its own layer_image region; all of them lie in x -111.77..-108.73, y 47.36..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -116.84,-19.49|-32.28,18.6250 nets cross one void in the GND plane on MIDLAYER1 and the GND plane on TOP_LAYER at 22 places, the longest 22.26 mm; 179 over tracks of other nets routed inside it (fastest: USB_DDP_N at 500 ps 10-90 %, suggested by its name)
Along 'ARM_2V5_GPIO_PD11' on MIDLAYER1, the GND plane on TOP_LAYER has 22.26 mm under the track with copper of ARM_2V5_GPIO_PE11, ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD10, FPGA_GPIO34, ARM_2V5_GPIO_PD12, FPGA_GPIO32, FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO33, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE8, not a plane, at (-67.92, -11.13), the same plane on both sides. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 179 of the crossings pass over tracks of other nets routed inside the hole on the reference layer: the plane is absent there, and those tracks stand in it. 38 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 16.5 mm). 22 places on 50 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -116.84..-32.28, y -19.49..18.62. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 61 of the 183 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-65.71, 1.54), 11.95 mm over copper of ARM_2V5_GPIO_PD12, FPGA_GPIO32, FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO33, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-69.06, -11.58), 5.86 mm, running ALONG the bare copper for 2.9 mm, not across it over copper of ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE8, ARM_2V5_GPIO_PE11, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-79.19, -13.64), 1.09 mm over copper of ARM_2V5_GPIO_PE8, ARM_2V5_GPIO_PE12, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD10' on TOP_LAYER at (-67, -7.74), 1.35 mm over copper of ARM_2V5_GPIO_PD11, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-67.92, -11.13), 22.26 mm, running ALONG the bare copper for 6 mm, not across it over copper of ARM_2V5_GPIO_PE11, ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD10, FPGA_GPIO34, ARM_2V5_GPIO_PD12, FPGA_GPIO32, FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO33, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE8, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-63.78, 2.15), 9.91 mm over copper of FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-69.51, -8.83), 14.42 mm, running ALONG the bare copper for 9.24 mm, not across it over copper of FPGA_GPIO34, FPGA_GPIO35, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on TOP_LAYER at (-67.23, -5.04), 3.24 mm, running ALONG the bare copper for 1.1 mm, not across it over copper of ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO35, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-70.3, -11.63), 3.08 mm over copper of ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE8, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-78.58, -13.03), 1.09 mm over copper of ARM_2V5_GPIO_PE8, ARM_2V5_GPIO_PE12, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE11' on TOP_LAYER at (-67.28, -10.08), 3.44 mm, running ALONG the bare copper for 1.4 mm, not across it over copper of ARM_2V5_GPIO_PD11, ARM_2V5_GPIO_PD10, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE12' on TOP_LAYER at (-74.61, -12.75), 10.17 mm, running ALONG the bare copper for 6.09 mm, not across it over copper of ARM_2V5_GPIO_PE11, ARM_2V5_GPIO_PD10, ARM_2V5_GPIO_PD11, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE8' on TOP_LAYER at (-74.8, -12.47), 10.92 mm, running ALONG the bare copper for 5.88 mm, not across it over copper of ARM_3V3_GPIO_PB1, ARM_2V5_GPIO_PE11, ARM_2V5_GPIO_PD10, ARM_2V5_GPIO_PD11, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-63.27, 2.32), 8.95 mm over copper of FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB0' on TOP_LAYER at (-67.81, -8.92), 2.41 mm over copper of ARM_2V5_GPIO_PD11, ARM_3V3_GPIO_PB1, ARM_2V5_GPIO_PD10, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-74.86, -12.6), 11.87 mm, running ALONG the bare copper for 8.41 mm, not across it over copper of ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PE8, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on TOP_LAYER at (-63.46, 0.85), 2.19 mm over copper of ARM_3V3_GPIO_PB0, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO13' on TOP_LAYER at (-65.98, 0.71), 1.76 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO17' on TOP_LAYER at (-63.53, 0.33), 1.94 mm over copper of FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO17' on TOP_LAYER at (-65.98, 0.33), 1.76 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO20' on TOP_LAYER at (-65.43, 6.66), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO21' on TOP_LAYER at (-63.53, -0.33), 1.94 mm over copper of FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO21' on TOP_LAYER at (-65.98, -0.33), 1.76 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO22' on TOP_LAYER at (-65.43, 7.67), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO24' on TOP_LAYER at (-65.43, 5.69), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO25' on TOP_LAYER at (-63.53, -0.76), 1.94 mm over copper of FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO25' on TOP_LAYER at (-65.98, -0.76), 1.76 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO27' on TOP_LAYER at (-65.43, 6.17), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO28' on TOP_LAYER at (-65.43, 3.58), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO29' on MIDLAYER1 at (-64.24, 2.15), 8.95 mm over copper of FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO29' on TOP_LAYER at (-64.51, -1.49), 0.76 mm over copper of FPGA_GPIO32, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO29' on TOP_LAYER at (-65.98, -1.8), 1.76 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO30' on TOP_LAYER at (-65.43, 4.17), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO31' on TOP_LAYER at (-65.43, 5.03), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO32' on MIDLAYER1 at (-64.69, 2.15), 9.91 mm over copper of FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO32' on TOP_LAYER at (-65.98, -3), 1.79 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO33' on TOP_LAYER at (-65.98, 2.12), 2.29 mm over copper of ARM_2V5_GPIO_PD10, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO34' on MIDLAYER1 at (-66.24, 2.74), 12.48 mm, running ALONG the bare copper for 1.4 mm, not across it over copper of ARM_2V5_GPIO_PD12, FPGA_GPIO32, FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO33, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO34' on TOP_LAYER at (-66.93, -6.3), 1.57 mm over copper of ARM_2V5_GPIO_PD11, ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO34' on TOP_LAYER at (-69.43, -6.55), 0.73 mm over copper of FPGA_GPIO35, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO35' on MIDLAYER1 at (-70.56, -7.9), 19.66 mm, running ALONG the bare copper for 6.96 mm, not across it over copper of ARM_2V5_GPIO_PD12, FPGA_GPIO32, FPGA_GPIO29, FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO33, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, FPGA_GPIO34, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO35' on TOP_LAYER at (-71.94, -11.04), 0.37 mm over copper of ARM_2V5_GPIO_PD12, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE10' on TOP_LAYER at (-47.44, 10.06), 1.02 mm over copper of USB_DDP_P, USB_DDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE10' on TOP_LAYER at (-54.59, 2.92), 1.02 mm over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE12' on TOP_LAYER at (-48.13, 10.06), 1.02 mm over copper of USB_DDP_P, USB_DDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE12' on TOP_LAYER at (-54.59, 3.6), 1.02 mm over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE13' on TOP_LAYER at (-42.22, 10.14), 9.9 mm, running ALONG the bare copper for 8.88 mm, not across it over copper of USB_DDP_P, USB_DDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE13' on TOP_LAYER at (-54.59, 2.21), 1.02 mm over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'USB_DDP_N' on MIDLAYER1 at (-42.24, 9.91), 21.57 mm, running ALONG the bare copper for 16.33 mm, not across it over copper of ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE10, ARM_2V5_GPIO_PE13, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'USB_DDP_P' on MIDLAYER1 at (-51.64, 7.11), 11.97 mm, running ALONG the bare copper for 7.33 mm, not across it over copper of ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE10, ARM_2V5_GPIO_PE13, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-71.72, 12.27), 0.73 mm over copper of FPGA_GPIO0, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-79.52, 11.79), 15.84 mm, running ALONG the bare copper for 15.09 mm, not across it over copper of FPGA_GPIO0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO0' on MIDLAYER1 at (-79.52, 11.81), 18.57 mm, running ALONG the bare copper for 16.5 mm, not across it over copper of ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on TOP_LAYER at (-71.34, 12.65), 0.73 mm over copper of FPGA_GPIO0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO3' on TOP_LAYER at (-71.03, 12.95), 0.73 mm over copper of FPGA_GPIO0, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-81.97, 12.27), 16.38 mm, running ALONG the bare copper for 15.71 mm, not across it over copper of FPGA_GPIO7, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO0' on TOP_LAYER at (-90.49, 11.81), 0.73 mm over copper of FPGA_GPIO7, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO2' on TOP_LAYER at (-74.01, 12.65), 0.73 mm over copper of FPGA_GPIO7, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO3' on TOP_LAYER at (-73.7, 12.95), 0.73 mm over copper of FPGA_GPIO7, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO7' on MIDLAYER1 at (-82.02, 12.24), 18.04 mm, running ALONG the bare copper for 15.81 mm, not across it over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO0, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-90.56, -13.64), 4.31 mm, running ALONG the bare copper for 2.92 mm, not across it over copper of ARM_2V5_GPIO_PE0, ARM_2V5_GPIO_PE2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-93.27, -11.99), 9.44 mm, running ALONG the bare copper for 6.6 mm, not across it over copper of ARM_3V3_GPIO_PB4, ARM_3V3_GPIO_PB5, ARM_2V5_GPIO_PE0, ARM_2V5_GPIO_PE2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE0' on TOP_LAYER at (-90.89, -13.11), 5.93 mm, running ALONG the bare copper for 2.92 mm, not across it over copper of ARM_2V5_GPIO_PE11, ARM_3V3_GPIO_PB1, ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD12, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-92.68, -13.03), 7.68 mm, running ALONG the bare copper for 6.56 mm, not across it over copper of ARM_2V5_GPIO_PE0, ARM_2V5_GPIO_PE2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE2' on TOP_LAYER at (-90.54, -13.41), 5.94 mm, running ALONG the bare copper for 2.97 mm, not across it over copper of ARM_2V5_GPIO_PD12, ARM_2V5_GPIO_PE11, ARM_3V3_GPIO_PB1, ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD10, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-94.47, -12.29), 11.3 mm, running ALONG the bare copper for 8.68 mm, not across it over copper of ARM_3V3_GPIO_PB4, ARM_3V3_GPIO_PB5, ARM_2V5_GPIO_PE0, ARM_2V5_GPIO_PE2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-94.12, -12.6), 11.3 mm, running ALONG the bare copper for 8.8 mm, not across it over copper of ARM_3V3_GPIO_PB4, ARM_3V3_GPIO_PB5, ARM_2V5_GPIO_PE0, ARM_2V5_GPIO_PE2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB4' on TOP_LAYER at (-94.32, -12.37), 10.1 mm, running ALONG the bare copper for 8.51 mm, not across it over copper of ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB5' on TOP_LAYER at (-93.9, -12.8), 10.13 mm, running ALONG the bare copper for 8.53 mm, not across it over copper of ARM_3V3_GPIO_PB1, ARM_3V3_GPIO_PB0, ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-62.59, -1.83), 11.08 mm, running ALONG the bare copper for 2.42 mm, not across it over copper of FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO27, FPGA_GPIO20, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on TOP_LAYER at (-62.43, 1.88), 0.73 mm over copper of ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO17' on TOP_LAYER at (-62.43, 0.74), 0.73 mm over copper of ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO21' on TOP_LAYER at (-62.74, -0.08), 0.73 mm over copper of ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO25' on TOP_LAYER at (-62.43, -0.48), 0.68 mm over copper of ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO28' on TOP_LAYER at (-62.74, 3.58), 0.52 mm over copper of ARM_3V3_GPIO_PB1, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-61.24, 5.92), 8.1 mm, running ALONG the bare copper for 1.05 mm, not across it over copper of FPGA_GPIO25, FPGA_GPIO21, FPGA_GPIO17, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, FPGA_GPIO22, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on TOP_LAYER at (-61.39, 2.92), 0.73 mm over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO17' on TOP_LAYER at (-61.08, 2.09), 0.73 mm over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO20' on MIDLAYER1 at (-61.58, 7.44), 0.96 mm over copper of FPGA_GPIO22, not a plane, to the end of the track; other side: no plane on GND / 'FPGA_GPIO22' on TOP_LAYER at (-60.76, 7.67), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO24' on TOP_LAYER at (-60.96, 6.83), 1.61 mm, running ALONG the bare copper for 0.79 mm, not across it over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO28' on TOP_LAYER at (-61.39, 3.81), 0.73 mm over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO30' on TOP_LAYER at (-61.08, 4.8), 0.73 mm over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO31' on TOP_LAYER at (-61.08, 5.44), 0.73 mm over copper of ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-56.63, 11.21), 6.62 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-56.16, 12.27), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-56.64, 11.79), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-58.81, 11.21), 6.62 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO16' on TOP_LAYER at (-59.05, 9.37), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO18' on TOP_LAYER at (-58.52, 9.91), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO19' on TOP_LAYER at (-57.78, 10.64), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO20' on MIDLAYER1 at (-57.8, 11.21), 6.62 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO23' on TOP_LAYER at (-59.64, 8.79), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO2' on TOP_LAYER at (-55.78, 12.65), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO3' on TOP_LAYER at (-55.47, 12.95), 2.92 mm over copper of ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-65.71, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-66.62, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-63.78, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-65.43, 12.27), 5.07 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-67.6, 11.79), 5.27 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB0' on MIDLAYER1 at (-63.27, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB2' on MIDLAYER1 at (-68.01, 10.27), 5.7 mm over copper of ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB3' on MIDLAYER1 at (-68.49, 11.21), 6.33 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO16' on TOP_LAYER at (-65.43, 9.37), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO16' on TOP_LAYER at (-69.13, 9.37), 0.73 mm over copper of ARM_3V3_GPIO_PB2, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO16' on TOP_LAYER at (-70.55, 9.37), 0.73 mm over copper of ARM_3V3_GPIO_PB3, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO18' on TOP_LAYER at (-65.43, 9.91), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO18' on TOP_LAYER at (-68.6, 9.91), 0.73 mm over copper of ARM_3V3_GPIO_PB2, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO18' on TOP_LAYER at (-70.02, 9.91), 0.73 mm over copper of ARM_3V3_GPIO_PB3, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO19' on TOP_LAYER at (-67.29, 10.64), 4.99 mm over copper of ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO19' on TOP_LAYER at (-69.28, 10.64), 0.73 mm over copper of ARM_3V3_GPIO_PB3, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO23' on TOP_LAYER at (-65.43, 8.79), 4.2 mm over copper of FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO23' on TOP_LAYER at (-69.71, 8.79), 0.73 mm over copper of ARM_3V3_GPIO_PB2, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO29' on MIDLAYER1 at (-64.24, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on TOP_LAYER at (-65.43, 12.65), 5.07 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO32' on MIDLAYER1 at (-64.69, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO33' on MIDLAYER1 at (-65.15, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO34' on MIDLAYER1 at (-66.24, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO35' on MIDLAYER1 at (-66.95, 11.21), 4.68 mm over copper of FPGA_GPIO23, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO3' on TOP_LAYER at (-65.43, 12.95), 5.07 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-51.22, 12.69), 4.9 mm over copper of FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-54.11, 12.27), 0.73 mm over copper of FPGA_GPIO23, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE8' on MIDLAYER1 at (-52.68, 11.1), 5.1 mm over copper of ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE9' on MIDLAYER1 at (-50.85, 12.7), 2.22 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane, to the end of the track; other side: no plane on GND / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-53.27, 11.79), 2.68 mm over copper of FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-54.59, 11.79), 0.73 mm over copper of FPGA_GPIO23, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO16' on MIDLAYER1 at (-51.92, 11.02), 5.4 mm, running ALONG the bare copper for 1.12 mm, not across it over copper of ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO18, FPGA_GPIO19, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO16' on TOP_LAYER at (-55.64, 9.37), 2.55 mm over copper of FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO16' on TOP_LAYER at (-57.44, 9.37), 0.73 mm over copper of FPGA_GPIO23, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO17' on MIDLAYER1 at (-53.4, 11.19), 5.16 mm over copper of ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO18' on MIDLAYER1 at (-49.84, 14.97), 1.95 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO18' on TOP_LAYER at (-55.11, 9.91), 3.58 mm over copper of FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO18' on TOP_LAYER at (-56.91, 9.91), 0.73 mm over copper of FPGA_GPIO23, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO19' on MIDLAYER1 at (-50.34, 14.47), 1.95 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO19' on TOP_LAYER at (-54.37, 10.64), 3.22 mm over copper of FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO19' on TOP_LAYER at (-56.17, 10.64), 0.73 mm over copper of FPGA_GPIO23, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO22' on MIDLAYER1 at (-54.22, 11.21), 5.32 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO23' on MIDLAYER1 at (-55.38, 11.21), 5.82 mm over copper of FPGA_GPIO2, FPGA_GPIO3, FPGA_GPIO16, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on TOP_LAYER at (-51.22, 13.27), 5.68 mm over copper of FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO3' on TOP_LAYER at (-51.22, 13.91), 5.71 mm over copper of FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-111.78, -11.99), 5.54 mm, running ALONG the bare copper for 0.99 mm, not across it over copper of ARM_2V5_GPIO_PE3, ARM_2V5_GPIO_PE5, ARM_2V5_GPIO_PE7, ARM_2V5_GPIO_PE9, ARM_2V5_GPIO_PE1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE1' on TOP_LAYER at (-113.81, -13.42), 0.73 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on TOP_LAYER at (-111.35, -11.83), 0.56 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on TOP_LAYER at (-112.73, -12.34), 0.73 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on TOP_LAYER at (-113.51, -13.13), 0.73 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on TOP_LAYER at (-110.8, -12.14), 0.71 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on TOP_LAYER at (-113.03, -12.83), 1.32 mm, running ALONG the bare copper for 0.5 mm, not across it over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on TOP_LAYER at (-110.12, -12.16), 0.59 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE9' on TOP_LAYER at (-109.58, -11.83), 0.52 mm over copper of ARM_2V5_GPIO_PD12, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE8' on MIDLAYER1 at (-58.37, 4.36), 4.76 mm over copper of FPGA_GPIO25, FPGA_GPIO13, FPGA_GPIO28, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO24, not a plane, to the end of the track; other side: no plane on GND / 'FPGA_GPIO13' on TOP_LAYER at (-58.61, 4.85), 1 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO24' on TOP_LAYER at (-57.07, 7.11), 1.55 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO25' on TOP_LAYER at (-58.55, 3.78), 0.58 mm over copper of ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO28' on TOP_LAYER at (-58.61, 5.41), 1.11 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO30' on TOP_LAYER at (-58.19, 5.99), 1.55 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO31' on TOP_LAYER at (-57.53, 6.66), 1.55 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, not a plane; other side: none: the signal layer is outermost
- and 10 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-116.84%2C-19.49%7C-32.28%2C18.62 serves each with its own layer_image region; all of them lie in x -115.06..-36.66, y -19.4..19.21 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -117.85,47.96|-116.39,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.45 mm (fastest: MGTRX113_3_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX113_3_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.45 mm under the track with copper of MGTRX113_3_N, not a plane, at (-117.22, 49.37), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.75 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -117.85..-116.39, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX113_3_N' on MIDLAYER1 at (-117.02, 49.92), 1.32 mm, running ALONG the bare copper for 0.78 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX113_3_P' on MIDLAYER1 at (-117.22, 49.37), 2.45 mm, running ALONG the bare copper for 1.75 mm, not across it over copper of MGTRX113_3_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-117.85%2C47.96%7C-116.39%2C50.7 serves each with its own layer_image region; all of them lie in x -118.44..-115.4, y 47.39..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -119.75,47.96|-118.3,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.44 mm (fastest: MGTRX113_2_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX113_2_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.44 mm under the track with copper of MGTRX113_2_N, not a plane, at (-119.13, 49.38), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.7 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -119.75..-118.3, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX113_2_N' on MIDLAYER1 at (-118.92, 49.94), 1.31 mm, running ALONG the bare copper for 0.76 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX113_2_P' on MIDLAYER1 at (-119.13, 49.38), 2.44 mm, running ALONG the bare copper for 1.7 mm, not across it over copper of MGTRX113_2_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-119.75%2C47.96%7C-118.3%2C50.7 serves each with its own layer_image region; all of them lie in x -120.34..-117.3, y 47.39..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -121.66,47.96|-120.2,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.41 mm (fastest: MGTRX113_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX113_1_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.41 mm under the track with copper of MGTRX113_1_N, not a plane, at (-121.03, 49.39), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.68 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -121.66..-120.2, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX113_1_N' on MIDLAYER1 at (-120.83, 49.95), 1.33 mm, running ALONG the bare copper for 0.64 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX113_1_P' on MIDLAYER1 at (-121.03, 49.39), 2.41 mm, running ALONG the bare copper for 1.68 mm, not across it over copper of MGTRX113_1_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-121.66%2C47.96%7C-120.2%2C50.7 serves each with its own layer_image region; all of them lie in x -122.25..-119.21, y 47.44..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -123.56,47.96|-122.11,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.41 mm (fastest: MGTRX113_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX113_0_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.41 mm under the track with copper of MGTRX113_0_N, not a plane, at (-122.94, 49.39), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.68 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -123.56..-122.11, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX113_0_N' on MIDLAYER1 at (-122.73, 49.95), 1.29 mm, running ALONG the bare copper for 0.73 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX113_0_P' on MIDLAYER1 at (-122.94, 49.39), 2.41 mm, running ALONG the bare copper for 1.68 mm, not across it over copper of MGTRX113_0_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-123.56%2C47.96%7C-122.11%2C50.7 serves each with its own layer_image region; all of them lie in x -124.15..-121.11, y 47.41..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -125.47,47.96|-124.01,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.41 mm (fastest: MGTRX112_3_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX112_3_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.41 mm under the track with copper of MGTRX112_3_N, not a plane, at (-124.84, 49.39), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.68 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -125.47..-124.01, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX112_3_N' on MIDLAYER1 at (-124.64, 49.95), 1.28 mm, running ALONG the bare copper for 0.75 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX112_3_P' on MIDLAYER1 at (-124.84, 49.39), 2.41 mm, running ALONG the bare copper for 1.68 mm, not across it over copper of MGTRX112_3_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-125.47%2C47.96%7C-124.01%2C50.7 serves each with its own layer_image region; all of them lie in x -126.06..-123.02, y 47.41..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -127.37,47.96|-125.92,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.41 mm (fastest: MGTRX112_2_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX112_2_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.41 mm under the track with copper of MGTRX112_2_N, not a plane, at (-126.75, 49.4), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.59 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -127.37..-125.92, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX112_2_N' on MIDLAYER1 at (-126.54, 49.96), 1.27 mm, running ALONG the bare copper for 0.66 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX112_2_P' on MIDLAYER1 at (-126.75, 49.4), 2.41 mm, running ALONG the bare copper for 1.59 mm, not across it over copper of MGTRX112_2_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-127.37%2C47.96%7C-125.92%2C50.7 serves each with its own layer_image region; all of them lie in x -127.96..-124.92, y 47.39..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -129.28,47.96|-127.82,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.47 mm (fastest: MGTRX112_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX112_1_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.47 mm under the track with copper of MGTRX112_1_N, not a plane, at (-128.65, 49.38), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.62 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -129.28..-127.82, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX112_1_N' on MIDLAYER1 at (-128.45, 49.94), 1.38 mm, running ALONG the bare copper for 0.56 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX112_1_P' on MIDLAYER1 at (-128.65, 49.38), 2.47 mm, running ALONG the bare copper for 1.62 mm, not across it over copper of MGTRX112_1_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-129.28%2C47.96%7C-127.82%2C50.7 serves each with its own layer_image region; all of them lie in x -129.87..-126.83, y 47.41..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -131.18,47.96|-129.73,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.37 mm (fastest: MGTRX112_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX112_0_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.37 mm under the track with copper of MGTRX112_0_N, not a plane, at (-130.56, 49.4), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.69 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -131.18..-129.73, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX112_0_N' on MIDLAYER1 at (-130.35, 49.96), 1.26 mm, running ALONG the bare copper for 0.7 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX112_0_P' on MIDLAYER1 at (-130.56, 49.4), 2.37 mm, running ALONG the bare copper for 1.69 mm, not across it over copper of MGTRX112_0_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-131.18%2C47.96%7C-129.73%2C50.7 serves each with its own layer_image region; all of them lie in x -131.77..-128.73, y 47.49..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -89.27,47.96|-87.82,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.41 mm (fastest: MGTRX116_1_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX116_1_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.41 mm under the track with copper of MGTRX116_1_N, not a plane, at (-88.65, 49.4), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.59 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -89.27..-87.82, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX116_1_N' on MIDLAYER1 at (-88.44, 49.95), 1.28 mm, running ALONG the bare copper for 0.76 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX116_1_P' on MIDLAYER1 at (-88.65, 49.4), 2.41 mm, running ALONG the bare copper for 1.59 mm, not across it over copper of MGTRX116_1_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-89.27%2C47.96%7C-87.82%2C50.7 serves each with its own layer_image region; all of them lie in x -89.86..-86.82, y 47.39..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -91.18,47.96|-89.72,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.51 mm (fastest: MGTRX116_0_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX116_0_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.51 mm under the track with copper of MGTRX116_0_N, not a plane, at (-90.55, 49.34), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.8 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -91.18..-89.72, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX116_0_N' on MIDLAYER1 at (-90.35, 49.89), 1.28 mm, running ALONG the bare copper for 0.87 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX116_0_P' on MIDLAYER1 at (-90.55, 49.34), 2.51 mm, running ALONG the bare copper for 1.8 mm, not across it over copper of MGTRX116_0_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-91.18%2C47.96%7C-89.72%2C50.7 serves each with its own layer_image region; all of them lie in x -91.77..-88.73, y 47.34..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -97.85,47.96|-96.39,50.73 nets cross one void in the GND plane on TOP_LAYER at 4 places, the longest 2.42 mm (fastest: MGTRX115_2_P at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX115_3_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.42 mm under the track with copper of MGTRX115_3_N, not a plane, at (-97.22, 49.41), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 3 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.51 mm). 4 places on 3 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -97.85..-96.39, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 3 of the 4 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX115_2_P' on MIDLAYER1 at (-97.82, 50.29), 0.28 mm over no copper; other side: no plane on GND
- 'MGTRX115_3_P' on MIDLAYER1 at (-97.22, 49.41), 2.42 mm, running ALONG the bare copper for 1.51 mm, not across it over copper of MGTRX115_3_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_3_N' on MIDLAYER1 at (-97.02, 49.13), 1.27 mm, running ALONG the bare copper for 0.75 mm, not across it over no copper, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'MGTRX115_2_P' on MIDLAYER1 at (-97.82, 49.33), 1 mm, running ALONG the bare copper for 0.97 mm, not across it over no copper; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-97.85%2C47.96%7C-96.39%2C50.7 serves each with its own layer_image region; all of them lie in x -98.84..-95.4, y 47.34..51.43 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:GND@TOP_LAYER:hole -99.75,47.96|-98.29,50.72 nets cross one void in the GND plane on TOP_LAYER at 2 places, the longest 2.4 mm (fastest: MGTRX115_2_N at 100 ps 10-90 %, ASSUMED)
Along 'MGTRX115_2_P' on MIDLAYER1, the GND plane on TOP_LAYER has 2.4 mm under the track with copper of MGTRX115_2_N, not a plane, at (-99.12, 49.4), running to the end of the track. No single drill's anti-pad and no landing explains it: a clearance is excused only when it holds a drill and is drawn round it, or the track ends in it on the net's own pad or via, or runs through its own via's clearance and no farther. The return current detours round the void. 2 of them run ALONG the bare copper, parallel to its edges, rather than across it (the longest 1.68 mm). 2 places on 2 net(s) cross it, listed below, the longest first. What cleared it: the hole at x -99.75..-98.29, y 47.96..50.7. One decision covers the void: whether these tracks may cross it, or the plane should be filled under them. 1 of the 2 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- 'MGTRX115_2_N' on MIDLAYER1 at (-98.92, 49.96), 1.33 mm, running ALONG the bare copper for 0.72 mm, not across it over no copper, to the end of the track; other side: no plane on GND
- 'MGTRX115_2_P' on MIDLAYER1 at (-99.12, 49.4), 2.4 mm, running ALONG the bare copper for 1.68 mm, not across it over copper of MGTRX115_2_N, not a plane, to the end of the track; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3AGND%40TOP_LAYER%3Ahole%20-99.75%2C47.96%7C-98.29%2C50.7 serves each with its own layer_image region; all of them lie in x -100.34..-97.3, y 47.44..51.29 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:routed@BOTTOM_LAYER|MIDLAYER2Tracks on BOTTOM_LAYER and MIDLAYER2 cross each other at 112 places, each layer the other's reference with its pour cleared round its own tracks, the longest 383.81 mm; 94 run ALONG the cut round another net's track (fastest: FPGA-GPIO36 at 100 ps 10-90 %, ASSUMED)
BOTTOM_LAYER and MIDLAYER2 each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 112 place(s) on 84 net(s), 19 of them seen from both tracks (each counted once). 94 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 284.21 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 101 of the 289 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-3.63, 276.01), 383.81 mm, running ALONG the bare copper for 281.22 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO27, ARM_2V5_GPIO_PE13, FPGA_GPIO24, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE10' on MIDLAYER2 at (-13.92, 110.59), 152.2 mm, running ALONG the bare copper for 108.05 mm, not across it over copper of FPGA_GPIO8, ARM_2V5_GPIO_PE5, FPGA_GPIO11, FPGA_GPIO10, FPGA_GPIO5, ARM_2V5_GPIO_PE4, FPGA_GPIO9, ARM_2V5_GPIO_PD12, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO14, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE10' on MIDLAYER2 at (-22.25, 42.21), 14.32 mm, running ALONG the bare copper for 12.02 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE12' on MIDLAYER2 at (-17.04, 113.96), 152.5 mm, running ALONG the bare copper for 111.58 mm, not across it over copper of GND, I2C_DL_SC14, I2C_DL_SD14, I2C_DL_SC9, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO14, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE13' on MIDLAYER2 at (-14.3, 162.46), 50.9 mm, running ALONG the bare copper for 36.11 mm, not across it over copper of FPGA_GPIO9, ARM_2V5_GPIO_PE4, ARM_2V5_GPIO_PD12, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO14, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE13' on MIDLAYER2 at (-16.08, 113.72), 110.13 mm, running ALONG the bare copper for 80.44 mm, not across it over copper of GND, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, FPGA_GPIO14, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO0, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-19.58, 120.4), 42.98 mm, running ALONG the bare copper for 37.9 mm, not across it over copper of ARM_2V5_GPIO_PE6, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-28.63, 44.93), 20.59 mm, running ALONG the bare copper for 10.79 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-18.75, 120.94), 99.34 mm, running ALONG the bare copper for 86.7 mm, not across it over copper of FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE6, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-27.51, 44.31), 24.21 mm, running ALONG the bare copper for 11.94 mm, not across it over copper of FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-5.49, 259.29), 339.04 mm, running ALONG the bare copper for 245.09 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, ARM_2V5_GPIO_PE10, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-4.95, 268.62), 357.99 mm, running ALONG the bare copper for 266.08 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-26.49, 44), 17.77 mm, running ALONG the bare copper for 11.6 mm, not across it over copper of FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, ARM_2V5_GPIO_PE14, FPGA_GPIO28, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-9.8, 245.83), 274.53 mm, running ALONG the bare copper for 195.34 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, ARM_2V5_GPIO_PE14, FPGA_GPIO28, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on BOTTOM_LAYER at (-9.07, 255.4), 317.17 mm, running ALONG the bare copper for 233.02 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, ARM_2V5_GPIO_PE15, FPGA_GPIO28, ARM_2V5_GPIO_PE14, FPGA-GPIO39, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE6' on BOTTOM_LAYER at (-20.57, 132.02), 209.59 mm, running ALONG the bare copper for 198.15 mm, not across it over copper of FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA_GPIO28, ARM_2V5_GPIO_PE14, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-18.97, 120.94), 226.51 mm, running ALONG the bare copper for 198.18 mm, not across it over copper of ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO20, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE14, FPGA_GPIO28, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-28.17, 44.92), 13.54 mm, running ALONG the bare copper for 11.12 mm, not across it over copper of ARM_2V5_GPIO_PE14, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO0' on BOTTOM_LAYER at (-22.6, 35.13), 9.03 mm over copper of FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO0' on BOTTOM_LAYER at (-3.23, 276.07), 364.07 mm, running ALONG the bare copper for 271.09 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO26, FPGA_GPIO27, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO10' on BOTTOM_LAYER at (-8.38, 255.38), 320.01 mm, running ALONG the bare copper for 235.1 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO11' on BOTTOM_LAYER at (-8.76, 255.41), 318.5 mm, running ALONG the bare copper for 234.25 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA_GPIO28, FPGA-GPIO39, ARM_2V5_GPIO_PE14, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO12' on BOTTOM_LAYER at (-19.33, 120.88), 210.64 mm, running ALONG the bare copper for 186.56 mm, not across it over copper of ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA_GPIO28, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO20, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE14, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO12' on BOTTOM_LAYER at (-28.63, 44.88), 12.28 mm, running ALONG the bare copper for 10.71 mm, not across it over copper of ARM_2V5_GPIO_PE14, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO14' on BOTTOM_LAYER at (-18.29, 120.85), 242.69 mm, running ALONG the bare copper for 211.1 mm, not across it over copper of FPGA_GPIO26, FPGA_GPIO27, ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO20, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO14' on BOTTOM_LAYER at (-27.31, 44.43), 15.73 mm, running ALONG the bare copper for 11.52 mm, not across it over copper of ARM_2V5_GPIO_PE15, FPGA_GPIO28, ARM_2V5_GPIO_PE14, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO15' on BOTTOM_LAYER at (-18.64, 120.88), 227.93 mm, running ALONG the bare copper for 197.73 mm, not across it over copper of FPGA_GPIO27, ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO20, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO15' on BOTTOM_LAYER at (-27.71, 44.72), 14.66 mm, running ALONG the bare copper for 11.38 mm, not across it over copper of FPGA_GPIO28, ARM_2V5_GPIO_PE14, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO1' on BOTTOM_LAYER at (-4.04, 275.92), 377.74 mm, running ALONG the bare copper for 284.21 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO27, ARM_2V5_GPIO_PE13, FPGA_GPIO24, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO21' on MIDLAYER2 at (-14.45, 110.8), 157.7 mm, running ALONG the bare copper for 113.65 mm, not across it over copper of FPGA_GPIO5, ARM_2V5_GPIO_PE4, FPGA_GPIO8, ARM_2V5_GPIO_PE5, FPGA_GPIO11, FPGA_GPIO10, FPGA_GPIO9, FPGA_GPIO14, ARM_2V5_GPIO_PD12, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO21' on MIDLAYER2 at (-22.96, 42.36), 16 mm, running ALONG the bare copper for 11.65 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO24' on MIDLAYER2 at (-16.54, 113.8), 153.97 mm, running ALONG the bare copper for 111.55 mm, not across it over copper of GND, I2C_DL_SC14, I2C_DL_SD14, ARM_2V5_GPIO_PD12, I2C_DL_SC9, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO14, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO0, ARM_2V5_GPIO_PE0, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO25' on MIDLAYER2 at (-17.53, 114.38), 110.43 mm, running ALONG the bare copper for 79.02 mm, not across it over copper of GND, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, ARM_2V5_GPIO_PE6, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO25' on MIDLAYER2 at (-18.39, 152.02), 26.95 mm, running ALONG the bare copper for 23.59 mm, not across it over copper of GND, FPGA_GPIO14, I2C_DL_SD10, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO26' on MIDLAYER2 at (-13.23, 163.02), 54.32 mm, running ALONG the bare copper for 36.92 mm, not across it over copper of +3V3, FPGA_GPIO9, ARM_2V5_GPIO_PE4, FPGA_GPIO8, ARM_2V5_GPIO_PE5, FPGA_GPIO11, FPGA_GPIO15, FPGA_GPIO14, ARM_2V5_GPIO_PD12, FPGA_GPIO12, ARM_2V5_GPIO_PE7, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO26' on MIDLAYER2 at (-23.47, 42.52), 17.43 mm, running ALONG the bare copper for 11.56 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO27' on MIDLAYER2 at (-13.72, 162.73), 52.53 mm, running ALONG the bare copper for 36.63 mm, not across it over copper of ARM_2V5_GPIO_PE5, +3V3, FPGA_GPIO9, ARM_2V5_GPIO_PE4, FPGA_GPIO8, ARM_2V5_GPIO_PD12, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO14, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO27' on MIDLAYER2 at (-23.97, 42.84), 18.87 mm, running ALONG the bare copper for 11.54 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO28' on MIDLAYER2 at (-19.18, 120.88), 86.28 mm, running ALONG the bare copper for 74.1 mm, not across it over copper of FPGA_GPIO12, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, ARM_2V5_GPIO_PE6, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO28' on MIDLAYER2 at (-27.99, 44.52), 20.18 mm, running ALONG the bare copper for 11.3 mm, not across it over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO30' on MIDLAYER2 at (-18.03, 120.85), 127.32 mm, running ALONG the bare copper for 100.61 mm, not across it over copper of FPGA_GPIO15, FPGA_GPIO14, FPGA_GPIO12, ARM_2V5_GPIO_PE7, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, ARM_2V5_GPIO_PE6, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO31' on MIDLAYER2 at (-18.39, 120.88), 126.59 mm, running ALONG the bare copper for 101.01 mm, not across it over copper of ARM_2V5_GPIO_PE7, FPGA_GPIO15, FPGA_GPIO12, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, ARM_2V5_GPIO_PE6, FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, not a plane, to the end of the track; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO4' on BOTTOM_LAYER at (-5.23, 259.85), 341.23 mm, running ALONG the bare copper for 246.88 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, ARM_2V5_GPIO_PE10, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE12, FPGA_GPIO25, FPGA_GPIO30, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO5' on BOTTOM_LAYER at (-8.08, 259.93), 328.96 mm, running ALONG the bare copper for 245.85 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE15, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO6' on BOTTOM_LAYER at (-4.34, 268.7), 363.73 mm, running ALONG the bare copper for 268.84 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, ARM_2V5_GPIO_PE13, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO7' on BOTTOM_LAYER at (-4.67, 268.64), 359.29 mm, running ALONG the bare copper for 267.34 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE13, FPGA_GPIO27, FPGA_GPIO26, FPGA_GPIO21, ARM_2V5_GPIO_PE10, FPGA_GPIO24, ARM_2V5_GPIO_PE12, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO8' on BOTTOM_LAYER at (-26.09, 43.84), 18.62 mm, running ALONG the bare copper for 11.54 mm, not across it over copper of FPGA_GPIO25, FPGA_GPIO30, FPGA_GPIO31, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO8' on BOTTOM_LAYER at (-9.45, 246.29), 276.83 mm, running ALONG the bare copper for 198.28 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, ARM_2V5_GPIO_PE13, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, FPGA_GPIO24, ARM_2V5_GPIO_PE14, FPGA_GPIO28, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO9' on BOTTOM_LAYER at (-10.06, 246.49), 262.52 mm, running ALONG the bare copper for 186.37 mm, not across it over copper of FPGA_GPIO13, FPGA_GPIO18, FPGA_GPIO19, ARM_2V5_GPIO_PE9, FPGA_GPIO16, ARM_2V5_GPIO_PE8, FPGA_GPIO17, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PE10, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, ARM_2V5_GPIO_PE13, ARM_2V5_GPIO_PE12, FPGA_GPIO24, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE14, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO9' on BOTTOM_LAYER at (-26.9, 44.15), 16.81 mm, running ALONG the bare copper for 11.7 mm, not across it over copper of FPGA_GPIO31, ARM_2V5_GPIO_PE15, ARM_2V5_GPIO_PE14, FPGA_GPIO28, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE12' on MIDLAYER2 at (-34.94, 14.56), 0.73 mm over copper of FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-43, 13.94), 2.03 mm over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-38.14, 13.94), 2.03 mm over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: no plane on PWR / 'ARM_3V3_GPIO_PB4' on BOTTOM_LAYER at (-43.83, 16.32), 5.47 mm, running ALONG the bare copper for 3.49 mm, not across it over copper of FPGA-GPIO36, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA-GPIO36' on MIDLAYER2 at (-44.23, 16.37), 12.69 mm, running ALONG the bare copper for 9.44 mm, not across it over copper of ARM_3V3_GPIO_PB4, FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO37' on MIDLAYER2 at (-48.58, 11.36), 11.51 mm, running ALONG the bare copper for 9.52 mm, not across it over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO38' on MIDLAYER2 at (-45.24, 13.94), 2.03 mm over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO39' on MIDLAYER2 at (-43.99, 13.94), 2.03 mm over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO24' on BOTTOM_LAYER at (-40.45, 14.4), 18.25 mm, running ALONG the bare copper for 9.8 mm, not across it over copper of FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA_GPIO31, FPGA_GPIO30, FPGA_GPIO25, ARM_2V5_GPIO_PE12, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO25' on MIDLAYER2 at (-35.67, 14.56), 0.73 mm over copper of FPGA_GPIO24, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO28' on MIDLAYER2 at (-38.82, 13.94), 2.06 mm over copper of FPGA_GPIO31, FPGA_GPIO24, not a plane, to the end of the track; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO30' on MIDLAYER2 at (-36.64, 14.18), 0.92 mm over copper of FPGA_GPIO24, not a plane, to the end of the track; other side: no plane on PWR / 'FPGA_GPIO31' on BOTTOM_LAYER at (-48.53, 11.52), 14.9 mm, running ALONG the bare copper for 9.61 mm, not across it over copper of FPGA-GPIO37, FPGA-GPIO38, FPGA-GPIO39, ARM_2V5_GPIO_PE14, FPGA_GPIO28, ARM_2V5_GPIO_PE15, FPGA-GPIO36, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO31' on MIDLAYER2 at (-37.44, 13.99), 1.46 mm, running ALONG the bare copper for 0.6 mm, not across it over copper of FPGA_GPIO24, not a plane, to the end of the track; other side: no plane on PWR
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE14' on MIDLAYER2 at (-50.56, 6.38), 14.07 mm, running ALONG the bare copper for 11.17 mm, not across it over copper of FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: CHASSIS_GND on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'ARM_2V5_GPIO_PE15' on MIDLAYER2 at (-50.34, 5.94), 15.05 mm, running ALONG the bare copper for 10.54 mm, not across it over copper of USB_5VBUS, FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: CHASSIS_GND on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO36' on MIDLAYER2 at (-55.35, 5.26), 2.85 mm over copper of FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO37' on MIDLAYER2 at (-54.69, 5.26), 2.85 mm over copper of FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: CHASSIS_GND on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA-GPIO38' on MIDLAYER2 at (-49.97, 9.21), 11.51 mm, running ALONG the bare copper for 8.08 mm, not across it over copper of FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: no plane on PWR / 'FPGA-GPIO39' on MIDLAYER2 at (-49.66, 8.28), 11.51 mm, running ALONG the bare copper for 8.34 mm, not across it over copper of FPGA_GPIO21, FPGA_GPIO26, FPGA_GPIO27, FPGA_GPIO30, not a plane; other side: CHASSIS_GND on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO21' on BOTTOM_LAYER at (-49.73, 7.44), 13.38 mm, running ALONG the bare copper for 8.33 mm, not across it over copper of ARM_2V5_GPIO_PE14, ARM_2V5_GPIO_PE15, FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO26' on BOTTOM_LAYER at (-49.76, 8.03), 13.67 mm, running ALONG the bare copper for 8.62 mm, not across it over copper of FPGA-GPIO39, ARM_2V5_GPIO_PE14, ARM_2V5_GPIO_PE15, FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO27' on BOTTOM_LAYER at (-49.86, 8.56), 13.6 mm, running ALONG the bare copper for 8.55 mm, not across it over copper of FPGA-GPIO39, ARM_2V5_GPIO_PE14, ARM_2V5_GPIO_PE15, FPGA-GPIO36, FPGA-GPIO37, FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO30' on BOTTOM_LAYER at (-49.87, 9.06), 13.71 mm, running ALONG the bare copper for 8.66 mm, not across it over copper of FPGA-GPIO38, FPGA-GPIO39, ARM_2V5_GPIO_PE14, ARM_2V5_GPIO_PE15, FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE6' on BOTTOM_LAYER at (-29.13, 45.39), 12.59 mm, running ALONG the bare copper for 10.87 mm, not across it over copper of FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost
- 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-29.54, 55.13), 10.1 mm, running ALONG the bare copper for 7.67 mm, not across it over copper of FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_3V3_GPIO_PB4' on BOTTOM_LAYER at (-52.17, 12.34), 8.56 mm, running ALONG the bare copper for 7.54 mm, not across it over copper of USB_HDP_N, USB_HDP_P, not a plane; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB5' on BOTTOM_LAYER at (-48.82, 15.44), 1.02 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'USB_HDP_N' on MIDLAYER2 at (-52.12, 12.36), 8.89 mm, running ALONG the bare copper for 7.42 mm, not across it over copper of ARM_3V3_GPIO_PB4, ARM_3V3_GPIO_PB5, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_HDP_P' on MIDLAYER2 at (-52.21, 12.56), 8.89 mm, running ALONG the bare copper for 7.48 mm, not across it over copper of ARM_3V3_GPIO_PB4, ARM_3V3_GPIO_PB5, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'FPGA_GPIO15' on BOTTOM_LAYER at (-29.21, 55.18), 8.81 mm, running ALONG the bare copper for 7.5 mm, not across it over copper of FPGA-GPIO39, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-43, 33.13), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-43, 35.24), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-43, 34.57), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-43.51, 37.39), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on BOTTOM_LAYER at (-43.51, 36.75), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-43.51, 38.84), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO0' on BOTTOM_LAYER at (-43.54, 32.64), 0.79 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO10' on BOTTOM_LAYER at (-43.51, 36.03), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO11' on BOTTOM_LAYER at (-43.51, 36.39), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO12' on BOTTOM_LAYER at (-43.51, 39.22), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO14' on BOTTOM_LAYER at (-43.51, 38.15), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO15' on BOTTOM_LAYER at (-43, 38.51), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO1' on BOTTOM_LAYER at (-43.51, 33.52), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO4' on BOTTOM_LAYER at (-43.51, 34.88), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO5' on BOTTOM_LAYER at (-43.51, 35.67), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO6' on BOTTOM_LAYER at (-43, 33.87), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO7' on BOTTOM_LAYER at (-43.51, 34.21), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO8' on BOTTOM_LAYER at (-43.51, 37.08), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO9' on BOTTOM_LAYER at (-43.51, 37.77), 0.72 mm over copper of USB_HDP_P, USB_HDP_N, not a plane; other side: none: the signal layer is outermost / 'USB_HDP_N' on MIDLAYER2 at (-43.16, 35.45), 7.3 mm over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, ARM_2V5_GPIO_PE6, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'USB_HDP_P' on MIDLAYER2 at (-43.36, 35.45), 7.31 mm over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, ARM_2V5_GPIO_PE6, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-30.8, 33.13), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-30.8, 35.24), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-30.8, 34.57), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-30.8, 37.39), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on BOTTOM_LAYER at (-30.8, 36.75), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE6' on BOTTOM_LAYER at (-30.8, 39.5), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-30.8, 38.84), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA-GPIO38' on MIDLAYER2 at (-30.8, 35.45), 7.3 mm over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, ARM_2V5_GPIO_PE6, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO0' on BOTTOM_LAYER at (-30.8, 32.72), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO10' on BOTTOM_LAYER at (-30.8, 36.03), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO11' on BOTTOM_LAYER at (-30.8, 36.39), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO12' on BOTTOM_LAYER at (-30.8, 39.22), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO14' on BOTTOM_LAYER at (-30.8, 38.15), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO15' on BOTTOM_LAYER at (-30.8, 38.51), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO1' on BOTTOM_LAYER at (-30.8, 33.52), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO4' on BOTTOM_LAYER at (-30.8, 34.88), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO5' on BOTTOM_LAYER at (-30.8, 35.67), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO6' on BOTTOM_LAYER at (-30.8, 33.87), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO7' on BOTTOM_LAYER at (-30.8, 34.21), 0.85 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO8' on BOTTOM_LAYER at (-30.8, 37.08), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO9' on BOTTOM_LAYER at (-30.8, 37.77), 0.86 mm over copper of FPGA-GPIO38, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE0' on BOTTOM_LAYER at (-32.75, 33.13), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE2' on BOTTOM_LAYER at (-32.75, 35.24), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE3' on BOTTOM_LAYER at (-32.75, 34.57), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE4' on BOTTOM_LAYER at (-32.75, 37.39), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE5' on BOTTOM_LAYER at (-32.75, 36.75), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE6' on BOTTOM_LAYER at (-32.75, 39.5), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'ARM_2V5_GPIO_PE7' on BOTTOM_LAYER at (-32.75, 38.84), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA-GPIO37' on MIDLAYER2 at (-32.51, 35.45), 7.3 mm over copper of FPGA_GPIO0, ARM_2V5_GPIO_PE0, FPGA_GPIO1, FPGA_GPIO6, FPGA_GPIO7, ARM_2V5_GPIO_PE3, FPGA_GPIO4, ARM_2V5_GPIO_PE2, FPGA_GPIO5, FPGA_GPIO10, FPGA_GPIO11, ARM_2V5_GPIO_PE5, FPGA_GPIO8, ARM_2V5_GPIO_PE4, FPGA_GPIO9, FPGA_GPIO14, FPGA_GPIO15, ARM_2V5_GPIO_PE7, FPGA_GPIO12, ARM_2V5_GPIO_PE6, not a plane; other side: +5V on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'FPGA_GPIO0' on BOTTOM_LAYER at (-32.75, 32.72), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO10' on BOTTOM_LAYER at (-32.75, 36.03), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO11' on BOTTOM_LAYER at (-32.75, 36.39), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO12' on BOTTOM_LAYER at (-32.75, 39.22), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO14' on BOTTOM_LAYER at (-32.75, 38.15), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO15' on BOTTOM_LAYER at (-32.75, 38.51), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO1' on BOTTOM_LAYER at (-32.75, 33.52), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO4' on BOTTOM_LAYER at (-32.75, 34.88), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO5' on BOTTOM_LAYER at (-32.75, 35.67), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO6' on BOTTOM_LAYER at (-32.75, 33.87), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO7' on BOTTOM_LAYER at (-32.75, 34.21), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO8' on BOTTOM_LAYER at (-32.75, 37.08), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost / 'FPGA_GPIO9' on BOTTOM_LAYER at (-32.75, 37.77), 1 mm over copper of FPGA-GPIO36, FPGA-GPIO37, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'FPGA_GPIO32' on BOTTOM_LAYER at (-48.45, 122.53), 2.55 mm, running ALONG the bare copper for 0.89 mm, not across it over copper of MGTTX115_3_P, MGTTX115_3_N, not a plane; other side: none: the signal layer is outermost / 'MGTTX115_3_N' on MIDLAYER2 at (-49.81, 123.33), 4.9 mm, running ALONG the bare copper for 3.54 mm, not across it over copper of NetCN1_U_WR_LINK_1_F3, NetCN1_U_WR_LINK_1_F1, FPGA_GPIO32, WR_LINK1_LED_LINK_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER / 'MGTTX115_3_P' on MIDLAYER2 at (-49.86, 122.34), 5.82 mm, running ALONG the bare copper for 4.36 mm, not across it over copper of NetCN1_U_WR_LINK_1_F3, FPGA_GPIO32, WR_LINK1_LED_LINK_U_WR_LINK_1, not a plane; other side: +3V6 on PWR, 0.127 mm from the track against 0.254 mm to BOTTOM_LAYER: 33% of the return on BOTTOM_LAYER
- 'ARM_2V5_GPIO_PD12' on MIDLAYER2 at (-12.07, 139.74), 5.65 mm, running ALONG the bare copper for 2.64 mm, not across it over copper of GND, ARM_3V3_GPIO_PB0, ARM_3V3_GPIO_PB1, not a plane, to the end of the track; other side: no plane on PWR
- and 100 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3Arouted%40BOTTOM_LAYER%7CMIDLAYER2 serves each with its own layer_image region; all of them lie in x -74.02..-2.23, y -14.56..398.98 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
void:routed@MIDLAYER1|TOP_LAYERTracks on MIDLAYER1 and TOP_LAYER cross each other at 87 places, each layer the other's reference with its pour cleared round its own tracks, the longest 13.23 mm; 41 run ALONG the cut round another net's track (fastest: LINK_ACT at 100 ps 10-90 %, ASSUMED)
MIDLAYER1 and TOP_LAYER each carry a pour and routed tracks, and each is the other's nearest reference. Wherever a track on one crosses a track on the other, the pour under it is cleared round that other track, so for the width of the cut the return has no plane under it and detours round the cut. 87 place(s) on 66 net(s), 16 of them seen from both tracks (each counted once). 41 of the crossings run ALONG the cut round another net's track rather than across it, parallel to its edges (the longest 10.21 mm): over or right beside that track, broadside to it as well as off the plane. One decision covers the layer pair: whether these layers may take a pour their own tracks cut as the reference, or the routing or the stackup should give the tracks a plane that is not cut where they cross. 87 of the 168 crossing(s) have a plane on the track's other side at most twice as far away as the broken one (to first order each plane beside a stripline carries a share of the return inversely proportional to its distance from the track). The rest leave most or all of the return to the break, so the finding is a warning.
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD13' on MIDLAYER1 at (-46.71, 24.45), 1.69 mm, running ALONG the bare copper for 0.39 mm, not across it over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE11' on MIDLAYER1 at (-50.56, 25.08), 5.12 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE8' on MIDLAYER1 at (-48.22, 25.08), 5.12 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB1' on MIDLAYER1 at (-52.11, 25.44), 3.9 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO16' on MIDLAYER1 at (-47.79, 25.08), 6.26 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO17' on MIDLAYER1 at (-48.76, 25.08), 5.12 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO20' on MIDLAYER1 at (-51.23, 25.15), 4.73 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO22' on MIDLAYER1 at (-49.26, 25.08), 5.12 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO23' on MIDLAYER1 at (-49.92, 25.08), 5.12 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on MIDLAYER1 at (-39.99, 25.8), 2.28 mm over copper of NetQ3_1, NetQ2_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetQ2_1' on TOP_LAYER at (-46.03, 25.98), 13.23 mm, running ALONG the bare copper for 1.01 mm, not across it over copper of FPGA_GPIO2, ARM_3V3_GPIO_PB7, ARM_3V3_GPIO_PB6, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE1, FPGA_GPIO3, ARM_3V3_GPIO_PB1, FPGA_GPIO20, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PD13, not a plane; other side: none: the signal layer is outermost / 'NetQ3_1' on TOP_LAYER at (-40.72, 25.39), 1.24 mm over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO3, FPGA_GPIO2, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'USB_CPU_DBG_N' on TOP_LAYER at (-47.76, 24.26), 7.55 mm, running ALONG the bare copper for 0.39 mm, not across it over copper of ARM_2V5_GPIO_PD13, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_3V3_GPIO_PB1, FPGA_GPIO20, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on TOP_LAYER at (-47.96, 24.05), 8.03 mm, running ALONG the bare copper for 0.65 mm, not across it over copper of ARM_2V5_GPIO_PD13, ARM_2V5_GPIO_PE11, FPGA_GPIO23, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_3V3_GPIO_PB1, FPGA_GPIO20, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'NetQ1_1' on TOP_LAYER at (-14.71, 20.58), 1.02 mm over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'NetQ1_3' on TOP_LAYER at (-14.71, 20.01), 1.02 mm over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'NetQ2_1' on TOP_LAYER at (-14.25, 16.45), 5.97 mm, running ALONG the bare copper for 4.95 mm, not across it over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'NetQ2_3' on TOP_LAYER at (-14.71, 15.96), 5.82 mm, running ALONG the bare copper for 4.8 mm, not across it over copper of USB_DDP_N, USB_DDP_P, not a plane; other side: none: the signal layer is outermost / 'USB_DDP_N' on MIDLAYER1 at (-14.55, 16.27), 12.67 mm, running ALONG the bare copper for 10.04 mm, not across it over copper of NetQ2_3, NetQ2_1, NetQ1_3, NetQ1_1, USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'USB_DDP_P' on MIDLAYER1 at (-14.35, 16.37), 12.87 mm, running ALONG the bare copper for 10.21 mm, not across it over copper of NetQ2_3, NetQ2_1, NetQ1_3, NetQ1_1, USB_CPU_DBG_N, USB_CPU_DBG_P, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- 'NetIC7_39' on TOP_LAYER at (-29.03, 58.09), 10.35 mm, running ALONG the bare copper for 4.68 mm, not across it over copper of FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_3V3_GPIO_PB1, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, FPGA_GPIO29, not a plane, to the end of the track; other side: none: the signal layer is outermost
- 'NetIC7_40' on TOP_LAYER at (-28.7, 58.2), 8.77 mm, running ALONG the bare copper for 3.24 mm, not across it over copper of FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, ARM_3V3_GPIO_PB1, FPGA_GPIO29, FPGA_GPIO33, FPGA_GPIO32, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE8' on MIDLAYER1 at (-30.79, 42.52), 1.63 mm over copper of ARM_3V3_GPIO_PB6, ARM_3V3_GPIO_PB7, ARM_2V5_GPIO_PD13, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB6' on TOP_LAYER at (-31.96, 45.01), 6.11 mm over copper of FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PD13, ARM_3V3_GPIO_PB7, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_3V3_GPIO_PB1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'ARM_3V3_GPIO_PB7' on TOP_LAYER at (-31.31, 45.65), 5.61 mm over copper of FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PD13, FPGA_GPIO22, FPGA_GPIO23, ARM_2V5_GPIO_PE11, FPGA_GPIO20, ARM_3V3_GPIO_PB1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'FPGA_GPIO16' on MIDLAYER1 at (-30.57, 42.3), 1.66 mm over copper of ARM_3V3_GPIO_PB6, ARM_3V3_GPIO_PB7, ARM_2V5_GPIO_PD13, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO17' on MIDLAYER1 at (-30.97, 42.87), 2 mm over copper of ARM_3V3_GPIO_PB6, ARM_3V3_GPIO_PB7, ARM_2V5_GPIO_PD13, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO22' on MIDLAYER1 at (-28.66, 45.69), 6.76 mm, running ALONG the bare copper for 1.86 mm, not across it over copper of ARM_3V3_GPIO_PB6, ARM_3V3_GPIO_PB7, ARM_2V5_GPIO_PD13, NetR28_1, NetR29_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO23' on MIDLAYER1 at (-28.87, 46.14), 7.28 mm, running ALONG the bare copper for 3.38 mm, not across it over copper of ARM_3V3_GPIO_PB6, ARM_3V3_GPIO_PB7, ARM_2V5_GPIO_PD13, NetR28_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER
- one crossing of two tracks, seen from each: 'SPEED' on MIDLAYER1 at (-42.91, 60.63), 6.95 mm, running ALONG the bare copper for 5.85 mm, not across it over copper of X25M_N, X25M_P, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'X25M_N' on TOP_LAYER at (-42.73, 63.09), 1.41 mm over copper of SPEED, USB_INDICATOR, RXI_N, RXI_P, not a plane; other side: none: the signal layer is outermost / 'X25M_P' on TOP_LAYER at (-42.73, 63.29), 1.41 mm over copper of SPEED, USB_INDICATOR, RXI_N, RXI_P, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on MIDLAYER1 at (-22.56, 58.57), 5.5 mm, running ALONG the bare copper for 3 mm, not across it over copper of NetIC7_40, NetR74_2, NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on MIDLAYER1 at (-22.99, 58.71), 5.79 mm, running ALONG the bare copper for 3.27 mm, not across it over copper of NetIC7_40, NetR74_2, NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO18' on MIDLAYER1 at (-23.29, 58.71), 5.73 mm, running ALONG the bare copper for 3.6 mm, not across it over copper of NetIC7_40, NetR74_2, NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on MIDLAYER1 at (-21.69, 58.71), 5.09 mm, running ALONG the bare copper for 2.8 mm, not across it over copper of NetIC7_40, NetR74_2, NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO3' on MIDLAYER1 at (-22.12, 58.71), 5.09 mm, running ALONG the bare copper for 2.84 mm, not across it over copper of NetIC7_40, NetR74_2, NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetIC7_39' on TOP_LAYER at (-23.12, 59.43), 3.28 mm, running ALONG the bare copper for 1.44 mm, not across it over copper of ARM_2V5_GPIO_PE1, FPGA_GPIO3, FPGA_GPIO2, FPGA_GPIO13, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'NetIC7_40' on TOP_LAYER at (-22.77, 55.44), 4.8 mm over copper of FPGA_GPIO3, FPGA_GPIO2, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE1, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, not a plane; other side: none: the signal layer is outermost / 'NetR74_2' on TOP_LAYER at (-21.85, 58), 5.97 mm, running ALONG the bare copper for 1.41 mm, not across it over copper of FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE1, FPGA_GPIO3, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE9' on MIDLAYER1 at (-32.13, 37.29), 0.73 mm over copper of PCB_HW_V_3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB6' on MIDLAYER1 at (-32.69, 37.29), 0.73 mm over copper of PCB_HW_V_3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB7' on MIDLAYER1 at (-33.28, 37.29), 0.73 mm over copper of PCB_HW_V_3, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO19' on MIDLAYER1 at (-31.86, 36.95), 5.82 mm, running ALONG the bare copper for 0.86 mm, not across it over copper of PCB_HW_V_2, PCB_HW_V_3, PCB_HW_V_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'PCB_HW_V_3' on TOP_LAYER at (-30.86, 37.63), 4.36 mm, running ALONG the bare copper for 0.55 mm, not across it over copper of FPGA_GPIO19, ARM_2V5_GPIO_PD13, ARM_3V3_GPIO_PB7, ARM_3V3_GPIO_PB6, ARM_2V5_GPIO_PE9, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on MIDLAYER1 at (-22.56, 52.42), 0.52 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE8' on MIDLAYER1 at (-25.53, 52.42), 0.73 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PE9' on MIDLAYER1 at (-24.26, 52.42), 0.64 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on MIDLAYER1 at (-22.99, 52.42), 0.52 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO16' on MIDLAYER1 at (-24.95, 52.42), 0.73 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO17' on MIDLAYER1 at (-26.11, 52.42), 0.73 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO18' on MIDLAYER1 at (-23.29, 52.73), 0.53 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO19' on MIDLAYER1 at (-23.78, 52.42), 0.6 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO22' on MIDLAYER1 at (-26.36, 52.73), 0.73 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on MIDLAYER1 at (-21.69, 52.56), 0.73 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO3' on MIDLAYER1 at (-22.12, 52.73), 0.52 mm over copper of NetIC7_39, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetIC7_39' on TOP_LAYER at (-24.45, 52.58), 5.64 mm over copper of FPGA_GPIO2, FPGA_GPIO22, FPGA_GPIO17, ARM_2V5_GPIO_PE8, FPGA_GPIO16, ARM_2V5_GPIO_PE9, FPGA_GPIO19, FPGA_GPIO18, FPGA_GPIO13, ARM_2V5_GPIO_PE1, FPGA_GPIO3, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PD10' on MIDLAYER1 at (-53.48, 28.18), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD11' on MIDLAYER1 at (-54.01, 28.71), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_2V5_GPIO_PD12' on MIDLAYER1 at (-52.37, 27.08), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB2' on MIDLAYER1 at (-54.65, 29.35), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'ARM_3V3_GPIO_PB3' on MIDLAYER1 at (-55.09, 29.79), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO29' on MIDLAYER1 at (-52.67, 27.37), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO32' on MIDLAYER1 at (-52.95, 27.65), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO33' on MIDLAYER1 at (-53.2, 27.9), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO34' on MIDLAYER1 at (-53.7, 28.4), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO35' on MIDLAYER1 at (-54.32, 29.02), 2.67 mm over copper of USB_CPU_DBG_P, USB_CPU_DBG_N, NetQ2_1, VBUS_USB2, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'NetQ2_1' on TOP_LAYER at (-55.52, 28.92), 4.79 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_N' on TOP_LAYER at (-56.01, 28.43), 4.77 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost / 'USB_CPU_DBG_P' on TOP_LAYER at (-56.15, 28.29), 4.77 mm over copper of ARM_3V3_GPIO_PB3, ARM_3V3_GPIO_PB2, FPGA_GPIO35, ARM_2V5_GPIO_PD11, FPGA_GPIO34, ARM_2V5_GPIO_PD10, FPGA_GPIO33, FPGA_GPIO32, FPGA_GPIO29, ARM_2V5_GPIO_PD12, ARM_3V3_GPIO_PB0, not a plane; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_2V5_GPIO_PE1' on MIDLAYER1 at (-29.96, 37.05), 3.62 mm, running ALONG the bare copper for 0.81 mm, not across it over copper of PCB_HW_V_1, PCB_HW_V_0, GND, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO13' on MIDLAYER1 at (-30.28, 37.24), 3.62 mm, running ALONG the bare copper for 0.72 mm, not across it over copper of PCB_HW_V_2, PCB_HW_V_1, PCB_HW_V_0, GND, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on MIDLAYER1 at (-28.56, 37.23), 0.73 mm over copper of PCB_HW_V_0, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO2' on MIDLAYER1 at (-30.09, 35.7), 2.46 mm over copper of PCB_HW_V_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO3' on MIDLAYER1 at (-28.87, 37.58), 0.97 mm over copper of PCB_HW_V_0, GND, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'FPGA_GPIO3' on MIDLAYER1 at (-30.3, 36.15), 2.46 mm over copper of PCB_HW_V_1, not a plane; other side: GND on GND, 0.254 mm from the track against 0.254 mm to TOP_LAYER: 50% of the return on TOP_LAYER / 'PCB_HW_V_0' on TOP_LAYER at (-28.71, 37.4), 1.9 mm over copper of FPGA_GPIO2, FPGA_GPIO3, ARM_2V5_GPIO_PE1, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'PCB_HW_V_1' on TOP_LAYER at (-29.36, 36.75), 2.55 mm over copper of FPGA_GPIO2, FPGA_GPIO3, ARM_2V5_GPIO_PE1, FPGA_GPIO13, not a plane, to the end of the track; other side: none: the signal layer is outermost
- one crossing of two tracks, seen from each: 'ARM_3V3_GPIO_PB2' on MIDLAYER1 at (-45.67, 62.52), 3.61 mm, running ALONG the bare copper for 2.74 mm, not across it over copper of X25M_N, X25M_P, not a plane; other side: no plane on GND / 'X25M_N' on TOP_LAYER at (-45.04, 63.35), 2.76 mm, running ALONG the bare copper for 0.73 mm, not across it over copper of LINK_ACT, ARM_3V3_GPIO_PB2, ARM_3V3_GPIO_PB3, not a plane, to the end of the track; other side: none: the signal layer is outermost / 'X25M_P' on TOP_LAYER at (-44.96, 63.55), 2.55 mm, running ALONG the bare copper for 0.73 mm, not across it over copper of LINK_ACT, ARM_3V3_GPIO_PB2, ARM_3V3_GPIO_PB3, not a plane, to the end of the track; other side: none: the signal layer is outermost
- and 75 more
Every site is a row of this finding's evidence, keyed by net, layers and position. GET /api/odb/boards/44/reference-planes?group=void%3Arouted%40MIDLAYER1%7CTOP_LAYER serves each with its own layer_image region; all of them lie in x -72.28..-10.83, y -0.67..390.52 mm (board frame, Y up).
Read from the copper as drawn on the reference layer, along each track's centreline at exact breakpoints. The reference is the copper beside the track, never the layer's type or name. Whether it matters depends on each signal's edge rate, which nothing on file states for these nets: a slow static line crosses a split harmlessly, a fast edge does not.
TPS51123 IC9 VREG5 has 10 uF (C71); the datasheet requires at least 33 uF
The 5 V LDO output VREG5 of the dual buck controller IC9 (TPS51123) is decoupled by one 10 uF capacitor (C71). The datasheet requires at least 33 uF on this pin, because VREG5 supplies the controller's analog core and both MOSFET gate drivers until the 5 V rail takes over.
What the datasheet requires
- Terminal functions table, p.7: "VREG5 17 O 5-V power supply output. Connect a 33-uF ceramic capacitor to Power GND near the device."
- Enable and soft start, p.21: "The VREG5 serves as the main power supply for the analog circuitry of the device and provides the current for gate drivers ... Add a ceramic capacitor with a value of at least 33 uF and place it close to the VREG5 pin".
- Layout guidelines, p.25: "VREG5 requires capacitance of at least 33-uF".
What the board has
Item Required (datasheet) On the board Margin Capacitance on VREG5 (IC9 pin 17) at least 33 uF 10 uF nominal (C71, the only capacitor on net VREG5) -23 uF (30 % of the minimum, before DC-bias derating) C71's value is 10 uF in both the BOM and the POWER sheet (p.15). The only other part on net VREG5 is R84 (100 k PGOOD pull-up). The BOM row puts C71 in an 0603 footprint, so its effective capacitance at 5 V bias will be lower than 10 uF.
``
mermaid flowchart LR VIN["+12V (IC9 pin 16 VIN)"] --> LDO["IC9 internal 5 V LDO"] LDO --> VREG5["VREG5 net (pin 17)"] VREG5 --> C71["C71 10 uF (only capacitor)"] VREG5 --> DRV["gate drivers DRVL1/2, and VBST via internal diode"] VO1["+5V (VO1, pin 24)"] -. "switch-over after VO1 > 4.7 V and PG" .-> VREG5``Why it matters
Until VO1 reaches 4.7 V and channel 1 reports power good (p.22, "VREG5 Switch Over"), both converters start up with their gate-drive current drawn from VREG5 alone. If VREG5 sags below the UVLO threshold (4.2 V wake-up, 0.43 V hysteresis, p.6), both switchers shut off (p.24, non-latching). The likely effect is a marginal or repeated start-up rather than damage. How much capacitance is needed in practice depends on the MOSFET gate charge and switching frequency. The datasheet states 33 uF as a minimum, and it is not met.
TPS51123 IC9 VREF is bypassed with 10 uF (C35); the datasheet range is 220 nF to 1 uF
The 2 V reference output VREF (pin 3) of IC9 (TPS51123) is bypassed by C35, a 10 uF capacitor. The datasheet asks for a 220 nF to 1 uF ceramic, so C35 is ten times the stated maximum. The same node also sets TONSEL (pin 4), which selects the 245/305 kHz switching frequency.
What the datasheet says
- Terminal functions, p.7: "VREF 3 O 2-V reference voltage output. Connect 220-nF to 1-uF ceramic capacitor to Signal GND near the device."
- Layout guidelines, p.25: "VREF requires a 220-nF ceramic bypass capacitor which should be placed close to the device".
- VREF output current is specified only for -5 uA < IVREF < 10 uA (p.4). The datasheet gives no start-up or stability figure outside the 220 nF to 1 uF range.
What the board has
Item Datasheet range On the board Margin VREF bypass (IC9 pin 3, net NetC35_1) 220 nF to 1 uF 10 uF (C35) +9 uF over the maximum (10x) The value comes from the BOM row (C35 in the 10 uF group) and from the POWER sheet, p.15, where C35 is drawn as 10uF on the VREF/TONSEL node. No other part is on that net. TONSEL is tied to the same node on purpose, to select 245/305 kHz (p.7).
``
mermaid flowchart LR VREF["IC9 pin 3 VREF (2.0 V out)"] --- N["NetC35_1"] TONSEL["IC9 pin 4 TONSEL"] --- N N --- C35["C35 10 uF (datasheet: 220 nF - 1 uF)"] C35 --- GND``Why it matters
The datasheet does not state the consequence, and none is claimed here beyond the deviation itself. The VREF output is only rated for about 10 uA of load, so a 10x larger capacitor may slow VREF at power-up, and the buffer's stability is characterised only inside the stated range. TONSEL reads this node to pick its frequency setting. A person should decide whether the value is intentional, for example by checking a CERN bench measurement or a TI EVM that used a larger VREF capacitor. The datasheet range is not met as drawn.
FPGA I2C buses pulled up to +2V5, but the TMP100 (IC3) and nine PCA9554 expanders on them run at 3.3 V (VIH = 0.7 x VCC = 2.31 V)
Two I2C buses from the FPGA are pulled up to +2V5, but every device on them is powered from a 3.3 V rail. These devices require SCL/SDA HIGH >= 0.7 x their supply = 2.31 V at 3.31 V, so a bus idling at 2.5 V leaves only about 0.19 V nominal margin. Supply and pull-up tolerances can consume that margin entirely.
The two buses
- FPGA-GPIO36 (SDA) / FPGA-GPIO37 (SCL): pull-ups R25/R26 4k7 to +2V5. Devices are IC3 TMP100 (SDA pin 6, SCL pin 1, V+ = +3V3) and U1_U_WR_LINK_1 PCA9554 (SDA 15, SCL 14, VCC = +3V3_SFP_U_WR_LINK_1).
- FPGA-GPIO38 (SDA) / FPGA-GPIO39 (SCL): pull-ups R23/R24 4k7 to +2V5. Devices are U1_U_WR_LINK_2 ... U1_U_WR_LINK_9 PCA9554 (SDA 15, SCL 14), each with VCC on its own +3V3_SFP_U_WR_LINK_n.
- No level translator sits on either bus. The +2V5 rail comes onto this board from the SCB via J1.81.
``
mermaid flowchart LR FPGA["FPGA (SCB) via J2.74/76/78/80"] --- BUS["SCL/SDA nets"] P25["+2V5 (from J1.81)"] -->|"R23-R26 4k7"| BUS BUS --- T["IC3 TMP100, V+ = +3V3 (3.31 V)"] BUS --- E["U1_U_WR_LINK_1..9 PCA9554, VCC = +3V3_SFP_n (3.31 V)"]``Numbers
Device Input-high requirement Supply (nominal / +2 %) VIH required Bus high level Margin TMP100 IC3 VIH min 0.7 x (V+) (TI SBOS231I p.5) +3V3 = 3.31 V / 3.37 V 2.31 V / 2.36 V +2V5 = 2.50 V nominal +0.19 V / +0.14 V PCA9554 U1_U_WR_LINK_1..9 SCL, SDA VIH min 0.7 x VCC (TI SCPS128D p.5) +3V3_SFP_n = 3.31 V / 3.37 V 2.31 V / 2.36 V 2.50 V +0.19 V / +0.14 V The 3.31 V comes from the AP7173 dividers: IC8 R46 4k7 / R76 1k5, and each IC6_U_WR_LINK_n R40 4k7 / R41 1k5, giving 0.8 x (1 + 4.7/1.5) (AP7173 p.2). The AP7173 output accuracy is +/-2 % (p.5). A +2V5 rail at -5 % (2.375 V) against a 3.37 V device supply leaves about 15 mV. The +2V5 tolerance is set on the SCB and is not stated on this board.
Context
The companion SCB has the same pattern on its own TMP100 bus (OBS-43 on OHWR0044 R1 WRS FL SCB). This observation covers the backplane's own devices, which are separate parts on separate nets. It works like an open-drain bus at a lower level. It usually does work, but with a margin that the datasheets do not guarantee.
D1 SMCJ13A on the 12 V input EXT_VIN: 13 V standoff, 21.5 V clamp; fits the downstream ratings except the unverified IMP811 path
The TVS D1 (SMCJ13A) on the external 12 V input fits the line. Its 13.0 V standoff sits above the 12 V nominal input, and its 21.5 V clamp at the rated pulse stays inside every downstream rating that is on file. Two limits remain open. The standoff margin is only 1.0 V, so a supply above 13 V would move D1 into leakage. The surge path through the R45/R77 divider into the IMP811 cannot be checked, because that datasheet is missing.
Ratings read (Littelfuse SMCJ series, p.2 table, row SMCJ13A)
Parameter SMCJ13A Line / downstream Margin Standoff VRWM 13.0 V EXT_VIN nominal 12 V (J6) +1.0 V (8 %) Breakdown VBR min @ 1 mA 14.40 V - - Clamp VC @ IPP 69.8 A 21.5 V TPS51123 VIN abs max 30 V (TI p.2) 8.5 V Clamp VC 21.5 V IRF7821 VDS 30 V (UMW p.1) 8.5 V Clamp VC 21.5 V C29-C31/C36/C37/C40/C41 rated 25 V (source BOM Voltage column) 3.5 V Peak pulse power 1500 W, 10/1000 us (p.1) - - Arrangement
``
mermaid flowchart LR J6["J6.2 EXT_VIN"] --> D1["D1 SMCJ13A to GND"] J6 --> F1["F1 3 A"] --> L15["L15"] --> V12["+12V: IC9 VIN, IC10/IC11 drains, R45/R77 divider to IC14"]``D1 is the first part at the connector, about 6 mm from J6, and its return is GND, the same net as J6.1. It sits ahead of F1, so a reverse-polarity or sustained over-voltage current through D1 is not fused.
Open points
- During a surge clamped at 21.5 V, the R45 6k8 / R77 4k7 divider puts about 8.8 V on IMP811 IC14 VCC. The IMP811 datasheet is not on file, so its absolute maximum cannot be checked.
- The J6 supply tolerance is a system requirement and is not stated on this board. Above 13.0 V the TVS runs beyond its standoff voltage.
Main parts
| Part number | Maker | Description | Where |
|---|---|---|---|
| 1206SFS400F/32-2 3A | Tyco | ??????? 1206SFS400F/32-2 | F1 |
| 219-4MST | 4 Positions DIP SWITCH | S1 | |
| 2EDG-5.08-2P-?? | J6 | ||
| 2EDG-5.08-3P-??? | J7 | ||
| 7A-25.000MAHE-T | U3 | ||
| AT93C56A-10SU-2.7 | U4 | ||
| AX88772BLI | IC7 | ||
| DMN2020LSN-7 | Diodes Inc. | N-Channel Power MOSFET | Q3 |
| FDN337N | N-Channel JFET | Q5 | |
| IMP811SEUS-T | IC14 | ||
| SFP_MHSP-85111-HDM | Socket for SFP module | CN2 | |
| SMCJ13A | Zener Diode | D1 | |
| TMP100NA/3K | I2C temp. sensor | IC3 | |
| TPS51123RGE | TEXAS INSTRUMENTS | Dual Synchronous Step-Down Controller For Low Voltage Power Rails | IC9 |
| APBL3025YSGC-F01 | Q1, Q2 | ||
| FDS6690AS | IC12, IC13 | ||
| IRF7821 | IC10, IC11 | ||
| PCA9548A | 8-channel 2C-bus switch with reset | IC1, IC2 | |
| PRTR5V0U2X | PHILIPS NXP | Ultra Low Capacitance Double Rail-to-Rail ESD Protection Diode | IC4, IC5 |
| QTS-048-02-L-D-DP-A | High Speed Ground Plane Header | J1, J2 | |
| USB-MINI-? | J3, J5 | ||
| SFP_MHSP-85121-YDM | SFP_SOCKET_DOUBLE_WITH_LIGHT_PIPE | CN1_U_WR_LINK_1, CN1_U_WR_LINK_2, CN1_U_WR_LINK_3, CN1_U_WR_LINK_4, CN1_U_WR_LINK_5, CN1_U_WR_LINK_6 and 3 more | |
| AP7173-SPG-13 | 1.5A Low Dropout Linera Regulator | IC6_U_WR_LINK_1, IC6_U_WR_LINK_2, IC6_U_WR_LINK_3, IC6_U_WR_LINK_4, IC6_U_WR_LINK_5, IC6_U_WR_LINK_6 and 4 more | |
| PCA9554PW | 8-bit I2C-bus SMBus I/O port with interrupt | U1_U_WR_LINK_1, U1_U_WR_LINK_2, U1_U_WR_LINK_3, U1_U_WR_LINK_4, U1_U_WR_LINK_5, U1_U_WR_LINK_6 and 4 more | |
| CC0603_10UF_6.3V_20%_X5R | Capacitor | C14_U_WR_LINK_1, C14_U_WR_LINK_2, C14_U_WR_LINK_3, C14_U_WR_LINK_4, C14_U_WR_LINK_5, C14_U_WR_LINK_6 and 12 more | |
| R0603_49R9_?%_0.25W_100PPM | SMD Resistor | R12_U_WR_LINK_1, R12_U_WR_LINK_2, R12_U_WR_LINK_3, R12_U_WR_LINK_4, R12_U_WR_LINK_5, R12_U_WR_LINK_6 and 12 more |
About this design
- Design
- WRS FL BACKPLANE — OHWR0043 R1
- Designed in
- Altium Designer
- Board
- 6 copper layers, 208.7 × 439.1 mm, 698 components, 535 nets
- Licence
- CERN-OHL-1.2
- Source
- https://gitlab.com/ohwr/project/wrs-fl-hw at commit
2ab905612229 - Attribution
- CERN Open Hardware Repository, project ohwr/project/wrs-fl-hw (commit 2ab9056122291de1bb29fb474d60db6378c82df6, 2026-07-03). Licence: CERN-OHL-1.2. Source: https://gitlab.com/ohwr/project/wrs-fl-hw. This is a snapshot of the copy published on the OHWR GitLab pages (R1), not CERN's released record. CERN's source of truth is EDMS (https://edms.cern.ch), and the current release may be newer.
- Reviewed with
- Probe by E# (E-Sharp AB)